Invacare® Alegio NG
Contents
1. E D DU 14 4 1 Mounting dismounting bed end onto U bracket style fitting 14 4 2 Mounting dismounting bed end onto Sanne style fitting 14 4 3 Mounting dismounting the steel Verso ll side rail 5 4 4 Mounting dismounting the Line and BrittV side 16 DOIG c CLP 7 4 6 Fitting the mattress support 7 UT en ee ee re ce ee ee ee ee ee ee eee 18 4 0 Transport ees bene hoes VA sees 19 5 Order numbers for 2 6 Cleaning and Maintenance 22 chee 22 6 2 Maintenance chart sa acus ERE 306 2 ene 23 6 3 MAMtenanGe 44 4 4 uer RET E E eee 24 OF Lubrication DIAN QI T peers cee ee Seda 24 7 Electrical system seem eda n SE 25 7 1 Trouble shooting the electrical system 26 7 2 Electro Magnetic Compliance EMC 27 8 Technical specificatio2. Hold the backrest 2 Remove the pipe pin from the backrest motor 3 Lower the backrest motor 4 Lower the backrest 13 N A minimum of 2 persons are required to emergency release a mattress section Both persons hold the mattress section One person pulls out the pipe pin Both slowly lower the mattress section until it is completely down 4 Accessories 4 1 Mounting dismounting bed end onto U bracket style fitting Mounting Lower the bed end in the U bracket fitting Press down firmly and ensure that bed end is fully seated at bottom of U bracket fitting Dismounting Hold bed end firmly on each side Pull up vertically on both sides at the same time 4 2 Mounting dismounting bed end onto Sanne style fitting Mounting Align the slots in the bed end with the tabs on the Sanne fitting Place bed end onto tabs and push down firmly and ensure that bed end is fully seated on the tabs Rotate the locking pin to allow it to engage with the bed end Dismounting Pull out he locking pin and rotate to temporarily disengage from bed end Repeat for both sides Hold bed end firmly on each side Pull up vertically on both sides at the same time 4 3 Mounting dismounting the steel Verso side rail Mounting The side rail must be mounted according to the side rails assembly instructions Tighten the side rail with the finger screws Dismounting Loosen the finger screws and remove the side rail Operatin
3. Modification of Alegio NG is strictly forbidden without authorization of Invacare 6 4 Lubrication plan We recommend lubricating the bed according to the following instructions Points of rotation in mattress support and base frame Lubricate with oil us a 2 Motor attachment points to mattress platform Lubricate with oil 3 Upper attachment point of Rastofix fitting Lubricate with oil 2 4 Scissor pivot bolts and attachment bolts Lubricate with oil NB The full length side rails gliding system must not be lubricated with oil otherwise the side rail bars will move sluggishly Lubricate with medically clean oil e g 50 order no 813239 NB Remove the mains plug from the socket before cleaning 24 7 Electrical system Voltage supply 230V 50 Hz Max current input 2A Voltage output 24V max 70 Intermittent periodic motor operation 10 max 2 min 18 min Sound level 45 50 dB A Protection class IPX6 Insulation class Il type B Alternating current Direct current Type B Applied part Potential equalization Indoor use only Thermal fuse product ry gt d gt gt n The bed is not provided with a mains switch so the mains plug is the only separation from the mains 25 7 1 Trouble shooting the electrical system amem em CS Motor plug not pushed fully into 1 Push the motor plug right into the control box control box The motor
4. 1563578 Version EN B Date 12 2012 Norway amp Iceland INVACARE AS Grensesvingen 9 Postbox 6230 Etterstad N 0603 Oslo Phone 47 22 57 95 00 Fax 47 22 57 95 01 www invacare no norway invacare com France INVACARE Poirier S A S Route de St Roch F 37230 Fondettes Phone 33 2 47 62 64 66 Fax 33 2 47 42 12 24 ww invacare fr contactfr invacare com Portugal INVACARE Lda Rua Estrada Velha 949 P 4465 784 Leca do Balio Phone 351 225 1059 46 47 Fax 351 225 1057 39 www invacare pt portugal invacare com 3rd party certified according to ISO 9001 150 13485 Germany INVACARE GmbH Alemannenstrasse 10 D 883 16 Isny Phone 49 75 62 7 00 00 Fax 49 75 62 7 00 66 www invacare de kontakt invacare com Italy INVACARE Mecc San s r l Via dei Pini 62 I 36016 Thiene VI Phone 39 0445 38 00 59 Fax 39 0445 38 00 34 www invacare it italia invacare com Australia INVACARE Australia Pty Ltd Lenton Place North Rocks NSW 2151 Phone 61 2 8839 5333 Fax 61 2 8839 5353 www invacare com au sales invacare com au Netherlands INVACARE BV Celsiusstraat 46 NL 6716 BZ Ede Phone 31 318 695 757 Fax 31 318 695 758 www invacare nl nederland invacare com csede invacare com Switzerland INVACARE AG Benkenstrasse 260 CH 4108 Witterswil Phone 41 61 487 70 80 Fax 41 61 487 70 8l www invacare ch switzerland invacare com New Zealand INVACARE NZ 4 Westfield Place Mt We
5. 8 1 Dimensions All measurements are stated in cm All angles are stated in degrees All measurements and angles are stated without tolerances Invacare reserves the right to change the stated measurements and angles 200 cm 80 cm 23 cm 30 cm 67 cm 28 80 cm 153 205 HI 0 70 32 8 2 Environmental conditions Environment Conditions Relative Atmospheric Lighting T t is iti emperature humidity pressure conditions Storage 15 700 hPa A 93 1060 hPa y Operating From 5 15 700 hPa An To 40 93 1060 hPa aware that when a bed has been stored under low temperatures it must adjusted to operating conditions before use Dust and lint have no effect on operation of bed 33 8 3 Weights Alegio NG bed Alegio NG complete standard bed excluding accessories 65 0 kg frame head section Standard 14 0 kg Top frame head 17 0 kg Top frame leg section 15 5 kg Top frame leg section Thigh 17 0 kg Top frame leg section Foot 17 0 kg Base and shedr Anil tanec onsen os ate cee 35 0 kg In MM 15 5 kg
6. ere Rastofix Exil M P ene ey Cee me a eee er eee mene ee ere eer mee eae ee ee ee err Paint for repair SPU P7208 uta doe eae eae ae ACER Hand set HL72 with integrated ACP function SX FEET COEPI Hand set HL73 with integrated ACP function SPIT OTA Mp Hand set HL74 with integrated ACP function Sig LUC roe rs ree eT ee eee Te eT Tere ee ee ee eee er eee ere re ee ore ce eee Hand set HB72 PT eee ee eee eee ee eee ee ee ee ee ee Hand set HB73 SLE Ce eee ee ee eee eee Seer ee ee er ee ee ee ee eee ee ee ee ree er ee Hand set HB74 nba c MERIT Be cate bere eat oe ease oa oe hE oe oes Safety Floor Mattress xxxx Colour must be indicated Bee 0125 White pigmented 0126 CER 0127 2 6 Cleaning and Maintenance 6 1 Cleaning The bed does not tolerate cleaning in automatic washing plants or the use of water jet based cleaning equipment Please make sure the power plug is removed from the socket outlet before cleaning The bed should be washed down using a wet sponge cloth or brush Use ordinary household cleaning agents Never use acids alkalines or solvents such as acetone or cellulose thinner The hand control motors and control unit may be washed with brush and water but not with pressurized w
7. is not running 2 The motor is defective 2 Replace the motor The relay in the control box makes a clicking noise 3 Motor cable is damaged 3 Replace the cable 4 Control box defective 4 Replace the control box 5 Hand control defective 5 Replace the hand control Control box is in order except 2 as one direction on one channel Control box defective Replace the control box Motor is but the spindle does not move The motor cannot motor cannot life full load full load nee damaged Replace the motor Motor noise but no movement of ae rod Piston rod Piston rod operate inwards and not outwards inwards and not outwards 26 7 2 Electro Magnetic Compliance EMC Guidance and manufacturer s declaration electromagnetic emission The medical bed Alegio NG is intended for use in the electromagnetic environment specified below The customer or the user of the bed should assure that it is used in such an environment Emissions test Compliance Electromagnetic environment guidance The medical Alegio NG uses RF energy only for its internal function Therefore CISPR 11 Group its RF emissions are very low and are not likely to cause any interference in nearby electronic equipment partly The medical Alegio NG is suitable for use all establishments including Class B domestic establishments and those directly connected to the public low
8. voltage CISPR partly power supply network that supplies buildings used for domestic purposes Harmonic emissions Class IEC 61000 3 2 Voltage fluctuations flicker emissions Complies IEC 61000 3 3 27 Guidance and manufacturer s declaration electromagnetic immunity The medical bed Alegio NG is intended for use in the electromagnetic environment specified below The customer or the user of the bed should assure that it is used in such an environment IEC 60601 test level Compliance level Electromagnetic environment guidance Electrostatic discharge ESD IEC 61000 4 2 Electrostatic transient burst IEC 61000 4 4 Surge IEC 61000 4 5 Voltage dips short interruptions and voltage variations on power supply input lines IEC 61000 4 1 6 kV contact t 8 kV air 2 kV for power supply lines kV for input output lines kV differential mode 2 kV common mode 576 U 795 76 dip in U for 0 5 cycle 40 U 60 dip in U_ for 5 cycles 70 U 30 dip in U_ for 25 cycles 576 U 295 dip in U for 5 sec 6 kV contact t 8 kV air 2 kV for power supply lines kV for input output lines kV differential mode 2 kV common mode lt 5 76 U 795 dip in U for 0 5 cycle 40 U 60 dip in U_ for 5 cycles 70 U 30 dip in U for 25 cycles 559 20 4 795 76 dip in U for 5 sec Floors should
9. DIOS GMM een eae ner edq pe I EE Vt Ft 19 5 kg Alegio NG accessories Line Side fallor ees PAS eee eat RS LES TIS seers 4 5 kg Line extendable side rail 5 6 5 kg Britt V side rail 8 0 kg Verso 11 side rail 8 3 kg Rid 4 2 kg ico cr een 0 3 kg Mattress support extension 15 1 8 kg Bed Ends Vibeke piece 6 0 kg Bed Ends Emma 7 0 kg Bed Ends Susanne Sophie 8 5 kg 9 Waste disposal This product has been supplied from an environmentally aware manufacturer that complies with the Waste Electrical and Electronic Equipment WEEE Directive 2002 96 CE This product may contain substances that could be harmful to the environment if disposed of in places landfills that are not appropriate according to legislation The crossed out wheelie bin symbol is placed on this product to encourage you to recycle wherever possible Please be environmentally responsible and recycle this product through your recycling facility at its end of life All wooden parts must be dismantled and sent for incineration All electric parts must be d
10. Invacare Alegio NG Bed User manual EN This manual must be given to the user of the product C Before using this product read this manual and save for future reference Yes you can Contents General informato e 293 reerd beset wee Gece HV Ned 2 ee ee ee ees EE EE as 2 led CETEMNCAON eee ee ee ae es eee bears oe eee 3 3 Labels and 4 1 4 Safety 5 ic VYAO errean eRe eR EEEE EEE RE EAS 7 Receiving the 8 Z Parts ofthe Ded seeks Gees ahs E 8 2 2 Assembly of the 9 NC rm 2 4 Disassemble the Alegio NG Operating the bed x esie E Eua bb dure mq doe bct 12 3 1 Operating of the hand control 12 3 2 Operating the braking 12 3 3 Adjustment of leg section 13 3 4 Emergency lowering of the backrest and or thigh 13 A ACCESSO O s
11. NET eas Scala Medium 2 collapsible steel side rail one pair alu grey for SB 755 15300 147 0 931 9 48 wack OP Os ROE OY EROR SR Scala Decubi 2 collapsible steel side rail one pair alu grey for SB 755 act qub Se ee eee eee ag COR pm dal ere Side rail height extender for Line Line extendable beech piece 1538 120 0129 aay EXE ER RU S ee ee Eo bud aub E eb ape be bar doi oS qur d dc Side rail height extender for Britt IV beech piece 15427093 01533 eee ee eee ee LAGER UR eee qupd 2103 0 979 9909 89 9 3 909 8 9 5 Br dac dd Lifting pole with adjustable handle EL topo ae ee ee ee ee ee ee ee ee ee Drip rod bar steel epoxy support Sub ce ne eas oes eats Upgrade kit legrest actuator and locking handset Do ce ne rernm Transport kit for a assembled bed 17 74299 aqq PPS T ERE PES Trolley non compatible with central brake Cm Support handle H40xW30 WFO PR ee oe eee es eee a Geen ee ae neers oe Extension kit 15 SB7BT eli eee pe ene ee ed ee ee ee ee ee ere eS eee ee err ee Extension kit 15cm and foam insert 245 7 PT eee a ek ees 15 cm foam insert Sg hye Saree ee ee ee ee eee er 0 EEE A ee ee ee eer ee
12. ater Dry the bed after cleaning NB All plugs must be installed during washing of the bed 22 6 2 Maintenance chart Service and maintenance of the Alegio NG must only be performed by personnel who have received the necessary instruc tion or training Bed ld no Date Initials Visual inspection of all parts of the bed plastic deformation and or wear and tear of welded joints Check all pins and clips Check that all screws bolts nuts are tight Control of all centres of rotation motors mattress support parts All motors running without failures with regular speed and at low noise Check the Rastofix fittings and function Check that mains cable and plug are intact Check the running of the cable Check all remaining cables for damages Also check the running of the cables 23 Visual inspection of all bed ends for damages 6 3 Maintenance e Personnel who have received the necessary instructions or training may only perform Service and maintenance 1 of the bed When relocating the bed service must be carried out according to the service schedule Before use Ensure that all manual and electrical parts functions correctly and are in a secure state After 3 months Ensure that all manual and electrical parts are functioning and tighten bolts screws nuts etc Every two year Service should be performed after the maintenance chart See chapter 6 2 Maintenance chart
13. be less than V V m 30 Recommended separation distances between portable and mobile RF communications equipment and the medical bed Alegio NG The medical bed Alegio NG is intended for use in an electromagnetic environment in which radiated RF disturbances are controlled The customer or the user of the medical bed Alegio NG can help prevent electromagnetic interference by maintaining a minimum distance between portable and mobile RF communications equipment transmitters and the medical bed Alegio NG as recommended below according to the maximum output power of the communications equipment Separation distance according to frequency of transmitter Rated maximum output m of transmitter 150 kHz to 80 MHz 80 MHz to 800 MHz 800 MHz to 2 5 GHz d 22 WP d WP Ei For transmitters rated at a maximum output power not listed above the recommended separation distance d in metres m can be estimated using the equation applicable to the frequency of the transmitter where P is the maximum output power rating of the transmitter in watts VV according to the transmitter manufacturer NOTE lI At 80 MHz and 800 MHz the separation distance for the higher frequency range applies NOTE 2 These guidelines may not apply in all situations Electromagnetic propagation is affected by absorption and reflection from structures objects and people 3l 8 Technical specifications 1 Further information available upon request of Invacare
14. be wood concrete or ceramic tile If floors are covered with synthetic material the relative humidity should be at least 30 76 Mains power quality should be that of a typical commercial or hospital environment Mains power quality should be that of a typical commercial or hospital environment Mains power quality should be that of a typical commercial or hospital environment If the user of the medical bed Alegio NG requires continued operation during power mains interruptions it is recommended that the medical bed Alegio NG be powered from an uninterruptible power supply or a battery IEC 60601 test level Compliance level Electromagnetic environment guidance Power frequency 50 60 Hz Power frequency magnetic fields should be at magnetic field 3 A m 3 A m levels characteristic of a typical location in a typical commercial or hospital environment IEC 61000 4 8 U_ is the c mains voltage prior to application of the test level Portable and mobile RF communications equipment should be used no closer to any part of the EQUIPMENT medical bed Alegio NG including cables than the recommended separation distance calculated from the equation applicable to the frequency of the transmitter Recommended separation distance Conducted RF IEC 61000 4 6 WP 1 3 5 Radiated RF d NP 80 MHz to 800 MHz 1 IEC 61000 4 3 d Ap 800 MHz to 2 5 GHz Ei 29 IEC 60601 test level Compliance level Electromagnetic en
15. dical electrical equipment used in medical procedures may be provided to help maintain or the condition of the patient Application environment 4 Care provided in a domestic area where medical electrical equipment is used to alleviate or compensate for an injury disability or disease 135 kg The max patient weight 35 kg provided that the weight of the mattress and the accessories do not exceed 35 kg Safe working load weight max 170 kg 170 kg The bed is not intended for children under 12 years and psychiatric patients Furthermore Be aware of the limitations of use mentioned in the warnings chapter 1 4 The following parts may be in contact with user during normal use of bed bed ends mattress deck mains E and hand control The Alegio NG is not intended to be used for patient transport The Alegio NG is suitable for refurbishment The Alegio NG bed is suitable for disinfection with household disinfectants If the patient height exceeds 2 meters it is recommended to use a mattress support extension JN The estimated product life cycle is 5 years for a Alegio NG bed The bed is quipped with loose cables which have to be exchanged if damaged The control unit external power supply hand control and motors are protected according to IPX6 Bed with lockable hand controls is only protected according to IPX4 The IP rating is a measure of protection against ingress of foreign matter into a product Remove the plug from th
16. ds onto trolley hooks 6 3 A 3 B 4A 5 A 20 5 Order numbers for accessories L332 CO Aen end eb ek CRA ed eA eR Os Vibeke NG wooden bed ends cherry for steel side rails i510 ee ee ee ee ee ee ee ee ee ee ee Oda bed end beech 90 cm Ol 6740 Ol oo ee fans Piggy bed end beech 90 cm Eco P Susanne bed ends Emma ends 15273992 90000 hs ee ee ee ee Pe he ae eee Sophie bed end dec ar Bese aed Ge rer Victoria bed end VCCI ED ol TTC eee eee ee ee ee eee EEES ee ee Tee ee eee ee ee ee ere Anita bed end hos fo Tus PCI Std Pies Verso ll steel side rail 53645820000 ah a ee eee ee ee ee benda PR NE REP ad Eq NIS M eda be aquest eis Britt V wooden side rail ence E PEPPER EADEM ae anna AN Id queas dee Line side rail beech one pair 152778 ODDO ea Papa eee ee eee Dorica quad d RU URGE Pee EX AGENS a Sas Line extendable side rail beech on pair 528990 0 199 ee eee ee ee ee ee ee ee eee ee ee ee EDU Scala Basic 2 collapsible steel side rail one pair alu grey loza cwm Scala Basic Plus 2 collapsible steel side rail one pair alu grey 15301380199 car Gnd Pong bane TESES EE
17. e mains voltage before moving the bed The cable must be kept clear off the floor and the castors during transportation Certification The Alegio NG bed is marked with the CE mark in accordance with directive 93 42 EEC concerning Medical Apparatus The Alegio NG bed have been approved according to IEC 6060 1 2 52 The Alegio NG bed has been approved and marked with the TUV mark The Alegio NG bed has undergone a risk analysis according to EN ISO 14971 2001 03 The Alegio NG bed has undergone a usability analysis according to IEC 60601 1 6 Invacare is certified according to DS EN ISO 9001 and ISO 13485 which ensures that our customers are always supplied with products of uniform quality Throughout the entire production process our materials products are quality controlled by the operators Additionally a final test is carried out prior to packaging and shipping If the product does not correspond to the quality demands of Invacare it will be discarded If contrary to our expectations a problem should arise in connection with the delivered product please contact your Invacare sup plier An address list is Shown on the back side at this manual Invacare reserves the right to alter product specifications without prior notice 1 3 Labels and symbols o WARNING This symbol warns of dangers If the necessary measurings not are taking it can result in injury or damage to the bed Instruction Reference to the user manua
18. g Up Lift up on the top tube of the side rail with a rotating motion toward the head end of bed Ensure the locking mechanism engages Down Pull the plastic knob on the locking mechanism and push down on the top tube of the side rail with a rotating motion toward the foot end of bed When 3 4 length using side rails you must always make sure that the distance between the bed end and the side rail s handle upper edge is between 0 6 cm for the the head section and more than 32 cm for the foot section There is a risk of entrapment of fingers on assembly and operation of the side rail Please ensure that the side rail locking system has engaged properly by pulling pushing the upper bar 4 4 Mounting dismounting the Line and Britt V side rail Mounting the Line and Britt V side rail Mount one end at a time Lift the upper bar the release buttons must face up outwards A 2 Press the locking pin at the end of the side rail with a finger 3 All three gliding shoes at the end of the bars are guided into the bed end rail until the lower bar has been locked thereby preventing the side rail from falling down B 4 Repeat points 2 and 3 when mounting the other end of the side rail To avoid entrapment suffocation or accidental fall accidents from the mattress support it is essential that the gliding shoes are correctly guided into the bed end rails Adjust the side rail bars by hand to ensure they are mounted correctly Di
19. has taken place and been accepted When using side rails it is essential to ensure correct fitting otherwise there is danger of entrapment suffocation between mattress support side rail and bed end Do not place any objects underneath bed Electromagnetic interference between the bed and other electrical products can occur To reduce or eliminate such electromagnetic interference increase the distance between the bed and the products or switch them off This medical bed can be used together with medical electrical equipment connected to the heart intracardially or the blood vessels intravascularly provided that following points are respected The medical bed should be equipped as describe above with means for potential equalization connection marked out by a symbol shown in the back of this manual Medical electrical equipment should not be fixed on the bed s metallic accessories such as side rails lifting pole drip rod bed ends ect In addition the medical electrical equipment power supply cord should be kept clear of the accessories or any other moving part of the bed Make sure that there are nothing under over or near the bed that can limit the movement of the bed or the mattress support such as furniture window frames and storage boxes Always lower the bed to the lowest position before leaving the patient in the bed unattended There is a risk of entrapment of fingers in the bed moving parts It can be da
20. ismantled and be disposed of as electric components Plastic parts must be sent for incineration or recycling Steel parts and castors must be disposed of as waste metals Waste disposal must comply with the laws and regulations pertaining waste handling in each country 34 35 36 37 Denmark INVACARE A S Sdr Ringvej 37 DK 2605 Br ndby Phone 45 36 90 00 00 Fax 45 36 90 00 0I www invacare dk denmark invacare com Austria INVACARE Austria GmbH Herzog Odilostrasse 101 A 5310 Mondsee Phone 43 6232 5535 0 Fax 43 6232 5535 4 www invacare austria at info austria invacare com United Kingdom amp Ireland INVACARE Ltd Pencoed Technology Park Pencoed UK Bridgend CF35 5AQ Phone 44 656 776 200 Fax 44 656 776 201 www invacare co uk uk invacare com ireland invacare com Manufacturer INVACARE Lda Rua Estrada Velha 949 P 4465 784 do Balio www invacare pt Customer Sales and Service Sweden amp Finland INVACARE AB Fagerstagatan 9 S 163 91 Spanga Phone 46 8 761 70 90 Fax 46 8 761 81 08 www invacare se sweden invacare com Belgium amp Luxemburg INVACARE N V Autobaan 22 B 8210 Loppem Br gge Phone 32 50 83 10 10 Fax 32 50 83 10 11 www invacare be belgium invacare com Spain INVACARE S A c Areny s n Poligon Industrial de Celra E 17460 Celra Girona Phone 34 972 49 32 00 Fax 34 972 49 32 20 www invacare es contactsp invacare com Ident no
21. l To identify the product please look at the Product label Type no of the bed Serial no Date of production bracers inam enmi Earl al ae m do Balis PORTUGAL tee 351 125 39 Fine PORTY 22 105738 1563584 0154 ui NN n max Ale gio NG WI as IPX4 fet 26 10 2012 44549 L3 1100 ERO y Code E0801 2 52 Alegio NG Symbols See chapter and 7 NOTE This symbol inform about important information and guidelines Electrical information See chapter 7 Pe 5 1467 1 4 Safety and Warnings Invacare accepts no liability for any use change or assembly of the product other than as stated in this user manual Accessories not mentioned in this manual must not be used The Alegio NG bed fulfils all requirements regarding maximum distances However if the bed is used for the care of patients with a small body dimensions it must be especially noted that there is a risk of such a patient slipping through the openings between the side rails or through the opening between the side rail and the mattress support The bed must not be used by patients under 12 years of age or by patients with body size equivalent to an average 12 years old or smaller The bed in combination with side rails must not be used for persons under 45 kg or under 150 cm height Either for persons that are restless spams or confused unless a professional risk assessment
22. llington Auckland Phone 64 9 917 3939 Fax 649 917 3957 www invacare co nz sales invacare co nz Yes you can
23. nd check that the cord is locked in the cord lock by pulling the handle The distance between the lifting pole and the mattress Minimum at 16 cm mattress 36 59 cm Y Maximum at 10 cm mattress 42 65 cm 4 6 Fitting the mattress support extension X4 Remove the bed end board 2 Loosen the machine screws that secure the standard length bed end brackets and remove 3 Insert the extended length bed end brackets into the frame tubes and secure with machine screws 55 4 Replace the bed end board secure with tapping screws SS gt 5 Add the mattress deck extender to the foot end of mattress deck SUR x SS 7 4 7 Mattress Safety aspects regarding combination of side rails and mattresses In order to obtain the highest possible safety level when using the bed in combination with side rails it is important to respect the minimum and maximum measures for mattresses stated in the table To mitigate the possibility of the user crawling over the top of the side rail with the risk of severe injury due to e g falling a mini mum vertical distance of 22 cm between the top of the mattress and the top of the side rail are to be respected The maximum mattress height in combination with a given side rail is stated in the table The Alegio NG is equipped with mattress support brackets These brackets must be properly installed on both sides of the bed in combination with the correct mattress size to prevent patient entrapment and ri
24. nd then raise the knee pivot point Attach cable fitting to bottom hole of deck bracket with clevis pin provided Make sure the head of the clevis pin is on the same side as the Rastofix deck brackets Secure clevis pin with hitch pin Lower the knee pivot point and ensure the cable and pin are mounted properly Control Box The control box is latched to the bed lifting motor The control box is provided with a label with symbols showing where to connect the motors plugs Backrest motor e Thigh section motor e Hand control Bed lifting motor 2 3 Wiring Route the head actuator cable under the control box over the shear assembly cross tube and into the hook on the mattress support cross tube Route cable un der head section motor housing Plug cable into motor and secure with locking clip Verify the mains cable strain relief is attached to the bed shear arm assembly Improper routing of cables could lead to user injury After completion of assembly always check that bed is fully func tional before placing patient in bed 2 4 Disassemble the Alegio NG bed Lock all castors Remove all accessories end boards and mattress Bring bed to its lowest height position and adjust all mattress support platform to horizontal Disconnect the mains power cable Roll cable and place on hook at head end of bed If the bed is provided with cable actuated foot section follow step 4 4 Unfasten cable from foot secti
25. ngerous to roll over the mains cable e Do not bring mains cable into moving parts e Disconnect the plug from the mains before moving the bed e he cables must be mounted in such a way that they are kept clear of the floor and do not block the castors We recommend to mount the mains cable on the hook for this purpose see picture 6 1 5 Warranty The warranty covers all material and production defects for 2 years from the date of delivery provided it can be demonstrated that such defects were present before delivery All manufacturing faults or defects must be promptly reported Invacare may repair the fault or replace the component The warranty provided by Invacare does not cover additional costs trans port packaging labour sundry expenses etc are for the customer s account The warranty does not cover Damage caused during transport that is not directly reported to the forwarder at the moment of delivery Repairs performed by unauthorized centers and personnel Parts subject to normal wear Malicious damage or damage caused by improper use of the bed 2 Receiving the bed 2 1 Parts of the bed e Check the packaging if the bed shows signs of damage upon delivery please see the terms of delivery Follow part must be provided Mattress support head end Mattress support bracket 4 pcs Mattress support foot end Motor for head end Castors 4 pcs Hand control Base frame Shear Arms Con
26. ns 32 8 1 UR QUA BOIS ORI ERR 32 8 2 Environmental conditions 33 lp C 34 J Waste disposal x ceno SER RUSSIE REP ER ER eee tee ain eR d S 34 Congratulations Congratulations on your choice of Invacare Alegio NG nursing bed Alegio NG is the dismountable nursing bed from Invacare designed especially for home nursing and long term care Alegio NG bed provides ease of handling combined with good functionality Please read the entire user manual before using the bed If you have any questions concerning the use or maintenance please contact us All indications of right and left are based on that a person lying on his back in the bed Please note that there may be sections in this user manual which are not relevant to your bed since this manual applies to all on the date of printing existing modules General information Product use The Alegio NG bed has been developed for domestic care long term care and features a comfortable sitting and lying position for the patient Furthermore ergonomical operation for the carer is ensured The Alegio NG bed is defined to be used according to Application environment 3 Long term care a medical area where medical supervision is required and monitoring is provided if necessary and me
27. nt Operating castors without central braking system Each of the castors is provided with brakes for both lengthwise and crosswise locking The brake is foot operated When the bed is positioned correctly at least one castor at the head end and one castor at the foot end must be locked 1 Braking Step on the pedal 2 Releasing the brake Step on the release pedal Operating the steerable castor The Alegio NG with central braking system may be equipped with a steerable castor The steerable castor is operated by means of the central braking pedal Activating the steering If the brake is in neutral step on the green pedal 2 Deactivating the steering Step on the red pedal until the brake is in neutral position Placement in the room N The bed must be placed so that the height adjustment up down is not obstructed by for example lifts or furniture Otherwise there is a risk for injury on user and or equipment 3 3 Adjustment of leg section optional Operate the leg section by lifting the leg section Up Lift the leg section Down Lift the leg section right up and then lower the leg section 3 4 Emergency lowering of the backrest and or thigh section An emergency release of the mattress support may be necessary in case of e g a power or motor failure An emergency release of the height adjustment is NOT possible x adi Remove the plug from the mains before emergency release of the mattress support
28. on deck bracket being sure to retain the clevis pin and hitch pin Unscrew the threaded knobs from the middle of both sides of the bed frame Pull the head section away from foot section to disengage brackets and plastic glides On the foot section rotate the locking pins on the snap lock fittings Pull foot section up and away from the shear arm pivot pins 3 Operating the bed 3 1 Operating of the hand control unit e A Sitting position lt Q Head section Thigh section optional Height adjustment of the bed om EH Key for locking and unlocking the Ex electrical functions Insert the key below each button to T respectively lock and unlock the hand control functions HL 70 with integrated ACP function HB70 To deactivate bed functions remove mains cord plug from power outlet 3 2 Operating the braking castors E Set off from the castors might under special conditions appear at different types of absorbing floor covering includ ing untreated or badly treated floors matters of doubt Invacare recommends to place a suitable kind of protec tion between the castors and the floor Do not release the brake with the fingers as there can risk of trapping Always apply the brakes when there is no need for moving the bed to avoid accidents during entering or exiting the bed and during handling of the patie
29. sk of suffocation To prevent head entrapment between the inside surface of the side rail and the mattress with the risk of e g suffocation a safety maximum space has to be respected When especially very thick mattresses or soft mattresses low density or a combination of these it is important to focus on this risk The minimum width and length of mattresses in combination with a given side rail is stated in the table Alegio NG Max Mattress Max Mattress Height Height Width Width Length Length For beds equipped with mattress support extension add 15 cm 18 4 8 Transport trolley Beforehand lock the brakes of 2 bottom castors of the base by positioning them upward to avoid that they touch the ground during the manipulation Mount foot section onto these tubes 1 with motor facing away from trolley cross channel 5 Secure foot section to trolley with finger knobs Place the lifting pole onto its location 2 2 Mount head section onto these tubes 3 with motor facing away from trolley cross channel 5 Secure head section to trolley with finger knobs 3 Align square glide bushings of base assembly with brackets 4 and roll onto trolley as far as possible Lift end of base assembly into a vertical position allowing the square glide bushings to engage into the brackets 4 Secure base to trolley with spring pins 4 Place Verso II Rails if applicable into cross channel of trolley 5 5 Place bed en
30. smounting the Line and Britt V side rail Lower the side rail 2 Dismount one end at a time Lift the lower bar so that the spring pawl is visible 3 Press the spring pawl with a key or a screwdriver C 4 Hold the lower bar Lower the side rail until all three bars are free of the bed end rail 5 Repeat points 2 to 4 when dismounting the other end of the side rail Operating Line and Britt V side rail The bed end may be equipped to lock the side rail at half height as well as in the top position Normally the side rail can only be locked in top position Up Pull up the top side rail bar until the locking pin locks with an audible click Down Lift the top side rail bar and press the two locking rings together Lower the side rail l6 Release 4 5 Lifting pole thumb screw If the lifting pole is used while the handle has been turned away from the bed the bed can tip when the handle is used Maximum load of the lifting pole is 80 kg Make sure that the lifting pole screw is properly tightened Position the lifting pole in such a way that the handle extends inwards across the Always lock lifting pole with Mounting Insert the lifting pole into the lifting pole tube and fix with the thumb screw Adjusting the height of the lifting pole handle Loosen the cord as shown A 2 lifting handle can now be adjusted to the desired height 3 Press the cord together as shown in B a
31. trol Box 10 Lift Motor Re po SLE T a Optional Beds Ends Beds Ends fitting Lifting pole Rastofix for leg section Mattress support extension 15 cm Motor for leg end Side rail Verso 11 Line Britt V Support handle Safety floor mattress Equipotentiality plug IV Drip Rod 2 2 Assembly of the Alegio NG bed 1 For questions concerning the assembly of your bed please contact your dealer or Invacare customer service Place base and shear arm assembly on floor and lock all cas tors 2 Place foot section on shear arms at end of bed with lifting actuator Align the plastic snap lock fittings with the pivot pins on the shear arm Press down firmly to engage the pivot pins in the snap lock fitting Rotate the locking pin on the snap lock fitting to prevent disengagement of foot section 3 Place head section on shear arms at opposite end of bed Align the square plastic glides with channel on head section Align the frame tubes with the brackets the foot section 5 4 Push the head section toward the foot section until the frame AA tubes are touching Secure the head and foot sections on each y ws gt side with the threaded knob DU am 2 7 3 C 4 mm mum VEA oW If the bed is provided with cable actuated foot section follow step 5 5 Unfasten cable from head section Lift foot section deck and lay cable over tube and guide pulley Lower foot section a
32. vironment guidance where p is the maximum output power rating of the transmitter in watts VV according to the transmitter manufacturer and d is the recommended separation dis tance in metres Field strengths from fixed RF transmitters as deter mined by an electromagnetic site survey should be less than the compliance level in each frequency range Interference may occur in the vicinity of equipment marked with the following symbol c NOTE At 80 MHz and 800 MHz the higher frequency range applies NOTE 2 These guidelines may not apply in all situations Electromagnetic propagation is affected by absorption and reflection from structures objects and people Field strengths from fixed transmitters such as base stations for radio cellular cordless telephones and land mobile radios amateur radio AM and FM radio broadcast and TV broadcast cannot be predicted theoretically with accuracy To assess the electromagnetic environment due to fixed RF transmitters an electromagnetic site survey should be considered If the measured field strength in the location in which the medical bed Alegio NG is used exceeds the applicable RF compliance level above the medical bed Alegio NG should be observed to verify normal operation If abnormal performance is observed additional measures may be necessary such as reorienting or relocating the medical bed Alegio NG Over the frequency range 150 kHz to 80 MHz field strengths should
Download Pdf Manuals
Related Search