EPROM PROGRAMMING BOARDS FOR ST9 MCU FAMILY
Contents
1. STA ST90E158 EPB EPROM PROGRAMMING BOARDS FOR ST9 MCU FAMILY MAIN FEATURES Programming of the ST90158 MCUs in window EPROM or plastic OTP version a PLCC84 and PQFP80 supported package a PC driven mode menu driven software S19 orintel hex file format DESCRIPTION The ST90E158 EPB EPROM Programming Board is designed for programming a win dow EPROM or OTP microcontroller of the ST90158 family The EPROM can be pro grammed on the ST90E158 or ST90T158 EPROM OTP members of the ST90158 family It is dedicated for programming pro July 1998 totypes or a small amounts of micro control lers For a mass production it s recommend ed to use the appropriate gang programmer The ST90E158 EPB can operate in remote mode under control of a MS DOS compatible computer using the standard PC parallel port Object code in either INTEL HEX or MO TOROLA S19 format is read from disk files to program the target device The menu driven software also offers VERI FY BLANK CHECK READ master and oth er utility functions Rev 1 0 1 14 1 INTRODUCTION 1 1 1 2 1 3 Table of Contents Device installation ON the socket 0 0 00 0000 00 cee ee ee ee POWG6ISUDDIY vs spe Sane a eh anh wk REA E Dee eb ae Ol RA 2 USING PRECAUTIONS AND WORK ENVIRONMENT 0 00 c cece eee e eee 2 1 2 2 2 3 3 OPERATION MODE 3 1 3 2 3 3 3 4 3 5 3 6 Testers and equipment o Work Stati2. 0 0 eee 2 14 Equipment supplied 0 00000 ee eee eens 9 9 4 INTRODUCTION 1 INTRODUCTION 1 1 Equipment supplied 1ST90E158 EPB programming board 1 Power supply 1 communication cable 13 1 2 floppy disk containing the software 1 2 Device installation on the socket Put the device onto the null insertion force socket with the erasure window on the top and the pin 1 matching the mark white point on board Take care not to make a mistake when positioning the device to avoid possible damages to both the board and the device 1 3 Power supply The board can be supplied from the integrated power supply provided with the board or from an external 15V DC 0 5A power supply When using an external power supply take care of the polarities marked nearby the two points connector 3 14 4 USING PRECAUTIONS AND WORK ENVIRONMENT 2 USING PRECAUTIONS AND WORK ENVIRONMENT 2 1 Testers and equipment This product conforms to the 89 336 EEC directive with reference to the EN55022 emissions standard for ITEs and EN50082 1 generic immunity standard This product is a class A appartus In a residential environment this device may cause radi oelectrical disturbances which may require the user to adopt appropriate precautions This product is not into an outer casing and is not therefore protected against the electrostatics dis charges ESD Therefore all tester equipment and tools used at any p
3. 0000 F7BF Last area Device separator Contents of EPB90158 DEV ST90E158 lt EEPROM addresses gt 0000 0000 lt EPROM addresses gt 0000 F7FF 0000 F7FF ST90T158 lt EEPROM addresses gt 0000 0000 lt OTP addresses gt 0000 F7BF 0000 F7BF Be very careful to respect the following points if you ever modify the file contents The different headers must not be modified The different memory areas must be in increasing order The min and max addresses of these areas must not exceed the min and max memory ad dresses of the device ki 13 14 ANNEXES Notes Information furnished is believed to be accurate and reliable However STMicroelectronics assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics Specifications mentioned in this publication are subject to change without notice This publication supersedes and replaces all information previously supplied STMicroelectronics products are not authorized for use as critical components in life support devices or systems without the express written approval of STMicroelectronics The ST logo is a registered trademark of STMicroelectronics 1998 STMicroelectronics All Rights Reserved Purchase of C Components by STMicroelectronics conv
4. ction is done by moving the inverted video bar until the desired device name is reached and by pressing lt cr gt Different informations are selected at the same time Memory mapping Version of microcontroller OTP EPROM ROM See ANNEX II for use of devices other than those listed by TYPE These informations have been read by the software from the file EPB90158 DEV during the startup phase of the software See file syntax in annex 2 These setup data are set by STMi croelectronics for each ST90158 family member and should not be changed by the custom ers Without these data or if they are corrupted the software will be unable to operate properly Notes 1 The name of the selected device is displayed at the bottom right corner of the screen 2 Until this function is complete all the other commands cannot be reached 3 6 2 DEV This function allows the user to display and verify the specifications of the previously selected device Pressing any key exits the function 3 6 3 LPT This function allows the user to change the selected parallel communication port The port is selected by moving the cursor to the desired port and pressing lt cr gt to validate the selection The default selection is port LPT1 ITA 7 14 OPERATION MODE 3 6 4 LOAD This function loads the data from the selected file into the PC memory buffer The user is prompted to enter the desired filename If no path or file extension a
5. er the INTEL HEX or the MOTOROLA 19 format Checksum error The data contained in the hexadecimal file are wrong You must verify the file content File contents exceeds memory size The data file content exceeds the device MCU memory capacity or doesn t match the availa ble memory areas Address gt memory size The specified address is greater than the maximum EPROM Start address gt End address The specified starting address is greater than the end address Access to non available memory range Access to a memory range which is not in the right memory space of the device as defined in the file EPB90158 DEV Writing disk error This error could be caused by a disk full situation Attempt to write to a write protected disk The disk is write protected Attempt to access to an unknown unit The specified destination drive is unknown by DOS system Drive not ready No disk is present or detected in the drive Drive error General failure during disk operation 4 11 14 ANNEXES Setup file not found During startup phase the remote software didn t find the setup data file in the working direc tory Invalid setup file content The content of the setup file is corrupted Port LPT1 is not installed No parallel port is installed on your computer Refer to your computer user manual Port LPT2 is not installed Only one or no parallel port is installed on your computer Refer to your computer user manu al Target c
6. eys a license under the Philips 12C Patent Rights to use these components in an 12C system is granted provided that the system conforms to the 12C Standard Specification as defined by Philips STMicroelectronics Group of Companies Australia Brazil Canada China France Germany Italy Japan Korea Malaysia Malta Mexico Morocco The Netherlands Singapore Spain Sweden Switzerland Taiwan Thailand United Kingdom U S A 14 14 STA
7. hip not present or defective Unsuccessful attempt to read or write to a device Check if the programmer is properly con nected and supplied if the device is inserted properly into the zero insertion force socket and if the device is not defective Blank check not performed on EEPROM Attempt to use the Blank check function when the EEPROM memory space is selected Device fails at address xxxxH During a Verify command or a verification performed at the end of a Programming command a mismatch has been found between the byte read from the device and the corresponding byte in the buffer During a Blank check of the EPROM this message indicates that a byte is not read as FF hex erased state 4 2 ANNEX II EPB90158 DEV syntax This file specifies the device names and the available EPROM and EEPROM memory areas it has the following syntax For a ST90E158 EPROM version Name of device ST90E158 Memory header lt EEPROM addresses gt Min and Max memory address in hex 0000 0000 Memory header lt EPROM addresses gt Min and Max memory address in hex 0000 F7FF Min and Max address of first area 0000 F7FF Last area Device separator 4 12 14 ANNEXES For a ST90T158 OTP version Name of device ST90T158 Memory header lt EEPROM addresses gt Min and Max memory address in hex 0000 0000 Memory header lt OTP addresses gt Min and Max memory address in hex 0000 F7BF Min and Max address of first area
8. n ooo towed haan Hea oe DE Redes Cee Ee eee eee eee ee Manipulation of finish goods 0 ccc ee eee Hardware installation omo dai ia 2 lede Riis io thea wd a dadd caddies Software installation isnin ia a a a ee eee Default path and file extension 1 0 ee ee Program execution 0 0 cee ee eee Selecting and exiting a command 0 0 00 c cette ee Funcions CESCIIPUONS 4 0 0 2 caw et eed rr ioe a e ned V A SSO SIV RES pe enee E S E a yh a a a a O se aan ache cue ath see te O A A hacen oe setae ates edecn eta a a at E eee wali 3 69 CPT Exa as a Ge w ek ac slew Sead Bie ales ee 0 EDAD ia eee EG 90 9 RAME icra A A ON 316 0 FILES ista a ena Powe an oe dele A wane mad etna 3 36 PROG oia e eet ete asia oa ada ida 30 89 VENIR toa ies ncaa tala E A ei ce at ae 3 6 9 BLANK aviar bis sl a A aaa Seana it eae ay a mae ane ale ahs 3 60 10 READS fod cn as be A So pea eee bead ae danke oe 91611 SPACES a A eh cate ean le Pea ae Ee eee eee IGAZ EXIT gic Pees news ce a te heeds A ee eee ee eed hee ee 3 6 13 RAM Galt CMU oe sc caer dearer new dl aoe aout dara aoe dh aoe gd ahd dd de ean 30 13 VAD DR gor a bic a he een eg es aes an EL ane eo ini te oe B 6 13 2EDIT S223 esas cowie ee al a ata aa edad odes aaa ada S613 SPILLS iria bees lee het hes AS oe aiaa IC APOUR eee red Saag a o is GANNEXES a A A meee ee hee eee a 4 1 ANNEX Errors messages 0 00 cee eee 4 2 ANNEX II EPB90158 DEV syntax 0
9. or not A blank EPROM byte reads as FF hex See error message description in annex 1 for more details 3 6 10 READ This function reads the content of the selected memory SPACE of the device and stores its content into the memory buffer After the read operation is complete the checksum of the read data will be displayed If any problem is encountered during reading an error message will appear on the screen 3 6 11 SPACE This function allows to select the device memory SPACE on which the PROG VERIF BLANK and READ commands will operate actually only EPROM OTP space on ST90158 devices The selected space is marked ON in the bottom right corner of the screen 3 6 12 EXIT This command allows the user to exit the program and return to the operating system 3 6 13 RAM edit menu This menu is accessed through the RAM function from the main menu It allows to examine and modify the memory buffer contents where the programming data are stored The screen displays a 128 byte range starting from the lowest memory address of the select ed memory area as defined in the file EPB90158 DEV 9 14 4 OPERATION MODE 3 6 13 1 ADDR This command allows to change the displayed address range of the memory buffer Any ad dress between the minimum and maximum device memory can be entered in hexadecimal Locations above the upper address limit of the device are not displayed 3 6 13 2 EDIT This command is used to edit
10. re provided the default settings will be used Data will be read from the file until either the memory buffer is full or end of file is reached The FILE checksum is then displayed as well as the DEVICE checksum which is the reflection of the device selected If the file doesn t exist or is not found in the specified directory a message will appear on screen and the user will be prompted to enter a new filename If any problems are encountered during file loading an error message will be displayed at the bottom of the screen See error message description in annex 1 for more details 3 6 5 RAM This command allows the user by the mean of a specific menu to examine and modify the contents of the memory buffer The RAM function operation will be detailed later see page of the present manual RAM menu section 3 6 6 FILE This function writes the data in the memory buffer onto the disk using the supplied filename This file is stored using an INTEL HEX format Should a file with the same name already exist the user will be prompted to confirm overwrit ing of the previous file If any problems are encountered during command execution an error message will be dis played at the bottom of the screen See error message description in annex 1 for more de tails 3 6 7 PROG The selected memory SPACE of the selected device will be programmed using the data stored in the memory buffer The user can modify the values from
11. rial interface of the PC damages to the board may occur Power the programmer using the power supply adaptor delivered with your programming board package it is adapted to the mains voltage and the mains outlet shape in use in your country Power on the computer Notes 1 The supplied interface cable has been tested in order to operate properly on most PC s please do not use another cable especially if it is longer that the one provided by STMicroe lectronics the board may not operate properly 2 The cable should be connected directly to the DB 25 female connector of the PC par allel port this connector is similar to the one present on the programming board please do not insert any additional cables nor switchboxes between the PC and the board a malfunction of the board may result 3 If a dongle hardware key required by some PC software is already connected on the PC parallel port it should not interfere with the programming board However if you notice a mal function of the board please remove the dongle s and restart the above sequence 3 2 Software installation First of all it is strongly recommended to copy the contents of the original source disk supplied with the ST90E158 EPB on another disk and to keep the original disk in a safe place Since the contents ofthe floppy disk are not copy protected you just have to type the following com mand COPY A C assuming the floppy disk is inserted in the A d
12. rive It is possible to work directly on a floppy disk but it is strongly recommended to install the soft ware package on your PC s hard disk in order to operate atthe maximum speed Then the fol lowing operations should be performed Insert the supplied disk in the relevant disk drive Usually drive A Create a working directory on your hard disk e g type MD C EPB90158 Type the following command COPY A CAEPB90158 The software package provided with the board includes the following files ky 5 14 OPERATION MODE EPB90158 BAT This is a batch file which calls the different graphics utilities and the main program This is the file to launch to start the EPROM Programming Software PGM90158 EXE This the main program EPB90158 DEV This file contains the list of the existing ST90158 family members including their names and programming address ranges EPB90158 LBR This file contains the different screens used by the main program BEG COM AFFICHE COM END COM are utility files for graphics screens All these files must be located in the same directory e g C EPB90158 3 3 Default path and file extension The default path for all the software is the path from which the program was called If the desired file is in another directory the user has to type the entire access path The default file extension is HEX and the default file type supported is the MOTOROLA for mat Neverthele
13. roduction step or for any manipulation of semi conductor devices must have its shield connected to GROUND 2 2 Work station The antistatic work station is composed of Aconductive table top made of steel or clean aluminium or covered by an antistatic surface superficial resistivity equal or superior to 0 5 Megohm cm2 grounded through a ground ca ble conductive cable from protected equipment to ground isolated through a 1 MQ resistor placed in series An antistatic floor covering grounded through a conductive ground cable with serial resistor between 0 9 and 1 5 MQ 2 3 Manipulation of finish goods Manipulation of finish goods must be made at a grounded work station see 2 1 and 2 2 It is mandatory to wear either on wrist or ankle an antistatic bracelet connected to the anti static floor covering or to the grounded equipment It is mandatory to wear antistatic gloves or finger coats Nylon clothing is prohibited during ma nipulation of parts The work station must be free of any non antistatic plastic objects The wearing of the antistatic bracelet must be controlled every day 4 4 14 OPERATION MODE 3 OPERATION MODE 3 1 Hardware installation The following steps must be performed Power off the computer Using the interface cable delivered with the board connect the PC computer parallel inter face port LPT1 or LPT2 to connector P1 of the ST90E158 programmer Do not connect the cable to a se
14. ss the INTEL HEX format is also usable when reading a file 3 4 Program execution Under MS DOS prompt type the command EPB90158 lt cr gt Note In this document lt cr gt stands for the Return key on the computer keyboard If you want to execute the program from MS Windows be careful to specify EPB90158 BAT as the executable file in order to launch the graphics environment properly A title screen is displayed Press any key to enter the TYPE menu Select the device type and press lt cr gt You can now select the desired function The different functions available are described in the following pages Note MS DOS and Windows are trademarks of Microsoft corporation 6 14 4 OPERATION MODE 3 5 Selecting and exiting a command For selecting a command the user can either move the cursor inverted video bar to the de sired function with the SPACE BAR oran arrow key and press lt cr gt or type the uppercase let ter corresponding to the desired command in the top screen menu Each time the cursor is moving a message briefly describing the selected function appears at the left bottom of screen Error messages are displayed at the bottom of the screen All the possible error messages are described at the end of the document Any function can be aborted by pressing the ESCAPE key 3 6 Functions descriptions 3 6 1 TYPE This function allows the user to select the type of device he wants to program The sele
15. start and end addresses of the memory area to be pro grammed otherwise the default values corresponding to the selected memory will be used The device memory will be programmed using a specific programming algorithm defined by STMicroelectronics After programming each byte the content of the device will be verified against the memory buffer byte to confirm the successful programming After a correct verify operation a success message will appear If a programming error is en countered a failure message will appear on screen indicating the failing byte address 8 14 ky OPERATION MODE If any other problem is encountered device not present in the socket defective device an error message is displayed at the bottom of screen See error message description in annex 1 for more details 3 6 8 VERIF This function compares the contents of the selected memory SPACE of the device against the data contained in the memory buffer The verify procedure is interrupted if any data mismatch is detected and an error message is displayed indicating the error address location See er ror message description in annex 1 for more details 3 6 9 BLANK This command performs a blank checking of the device EPROM memory The command is available only if an EPROM type device ST90E158 or ST90T158 and the EPROM memory space are currently selected A fail or success message will indicate whether the device EPROM is effectively blank
16. the memory buffer contents When starting the Edit session the cursor is positioned on the first address of the displayed screen The location selected by the cursor can be interactively modified by entering a new hexadecimal value The ASCII field on the right side of the screen is simultaneously updated Arrows keys may be used to access any location on screen The ESCAPE key is used to exit this command and return to the main menu 3 6 13 3 FILL A memory buffer area between two pre selected address limits can be set to any hexadeci mal value The user is prompted for the start address the end address the hex value to write to the se lected area and a confirmation for the previously entered data 3 6 13 4 PGUP This command displays the previous 128 byte page of the memory buffer 3 6 13 5 PGDN This command displays the next 128 byte page of the memory buffer 3 6 13 6 EXIT This command allows the user to exit the RAM menu and return to the main menu 4 10 14 ANNEXES 4 ANNEXES 4 1 ANNEX I Errors messages Device not yet selected This message means that you attempt to execute a command before selecting a device This is required to set different parameters like the maximum EPROM addresses File not yet loaded This message appears when the commands which operate on data in PC memory buffer are called before loading data from an hexadecimal file No hexadecimal file The selected file doesn t match eith
Download Pdf Manuals
Related Search