PM2700 - Digital Pen Plating System
Contents
1. 10 cm away from the walls for good air circulation 7 Do not stand or place heavy objects on the DPPS Use DPPS in flat stable position only 8 When DPPS is not used for an extended period of time disconnect the AC cord Basic Operations Preparation for work 1 2 3 Place the DPPS on horizontal stable surface avoiding direct sunlight Place the PS at least 10 cm 4 away from the walls for good air circulation Verify the specifications of your AC circuit 115V or 230V Check the position of input voltage value switch on the back of the unit Switch to the correct setting if necessary WARNING If the input voltage value setting of your unit does not correspond with the voltage value of your electrical circuit the Power Supply will be permanently damaged Do not use the electrical circuits which do not correspond to 110 120 V or 200 240 V 50 60 Hz 4 Insert the AC cord into the socket on the back side of the DPPS Plug the AC cord into the outlet Connect the anodes plating pens to the output terminals Connect the cathode black lead wire with alligator clip to the terminal Turn the voltage regulator 1 to the left position Turn the power switch 5 to ON position Turn the voltage regulator 1 to set the necessary voltage value 1 Turn the voltage regulator 1 to the extreme left position 2 Switch off the power switch 5 to OFF position 3 Unplug from the outlet Please be advised that our recomm2. 5 45 40502 Chisel tip pkg 5 Controls Names and Functions 1 Voltage regulator Top View Regulate the value of stabilized voltage 2 Digital Voltage indicator Terminals value voltage display Electrolyte Solution Jar holders Pen holders ON OFF switch Rear View A cord socket The input voltage value switch 3 Controls the value of input 4 voltage 115V 60Hz or 230V 50Hz 8 Terminals to connect electrodes Plating pens to stabilized voltage 9 Terminal to connect anode Ground wire with Alligator Clip to 10 Wire holder seat Sd SLD pie WARNING Before you begin Make sure the unit is switched to a correct Voltage Plugging the system into 230V outlet when system is set to 115V will permanently damage the system 1 Year Limited Warranty against factory defects Incidental or accidental damages due to improper use and or negligence is not covered under warranty All warranty claims must he accompanied with the original purchase receipt This warranty is extended to original purchaser only FOR PROFESSIONAL USE ONLY FD On Time 800 323 6091 FDJ On Time presents the manufacturer s instructions in a useful organized form Original instructions are available with the product
3. PEPETOOLS Digital Pen Plating System incorporates PM2700 Digital Pen Plating System Congratulations you have purchased one of the most advanced Digital Pen Plating Systems available State of the art circuitry Precise Digital Readout Stable Voltage Output Less than 1 variance at the max load Precision Voltage Regulator In 100mw increments 0 18V Automatic Current Limitation 500ma max Three 3 specially designed Electrode Styluses Plating Pens Make excellent contact with fiber electrodes Save Time use three different pens and solutions at the same time Compact Design Conveniently placed controls Dual Voltage 115V 60Hz 220V 50Hz User s Manual General Specifications INPUT 115 V AC 1 A max 60 Hz 230 VAC 0 5A max 50 Hz OUTPUT 17 VDC 0 5A max Short circuit protection Self restoring after elimination of short circuit Operating temperatures 5 C min 40 C max Overall dimensions 200 x 140 x 65mm 7 1 4 x 5 1 2 x 2 1 2 Mass weight 1 0 kg max 2 2lb Precautions 1 Do not expose the DPPS Digital Pen Plating System to rain or moisture 2 Donot expose the DPPS to acids or other corrosive chemicals 3 Do not remove the back cover 4 Donot place DPPS in direct sunshine or near heating source 5 When unplugging the unit from the AC outlet hold the plastic part Do not jerk the power cord and cold the metal part 6 Do not block the ventilation holes Place the DPPS at least
4. endations are very general and may not apply to your specific application We strongly recommend that you follow ALL THE SAFETY precautions working with an electrical device Also follow the plating solutions manufacturer s recommendations for proper handling use and disposal of plating solution The box contents 1 Power supply 2 Set of 3 platinum electrodes plating pens red yellow and white 3 3 Solution Jars with lids Empty 4 Black lead wire with alligator clip Cathode wire 5 Power cord 6 Wire holder 7 9 Fiber Electrodes 8 User s manual Troubleshooting Problem 1 Indicator light does not come on 1 Check if there is power in the network 2 Check the connection of AC cord in the outlet Special Instructions Inserting the felt tip into the _ Felt Tip PEPETOOLS Plating Pen Plating Pen a i The felt tips provided for the plating pen are very slightly oversized by design This is to insure that good contact is made with the platinum wire in the pen This is essential to good plating The tip must be presented at an angle to the pen see illustration Press the tip down on the platinum wire and push the tip into the pen at least 1 4 The platinum wire will make a slight groove on the felt tip which will allow the tip to be inserted into the pen The tip will not be able to be inserted unless this procedure is followed Replacement fiber tips available 45 405 Standard tip pkg 5 45 40501 Fine point ti kq
Download Pdf Manuals
Related Search