User Manual
Contents
1. 2 It is not allowed to use the partitioned and or password encoded USB memory Time sync through NTP server doesn t work NTP server requires DNS server address Please check if DNS server address is correct at Network tab E mail transmission doesn t work in using E mail notify function 1 E mail notify function works based on SMTP service Please check if the sending mail address is correct and if the mail server supports SMTP service 2 SMTP service is provided based on DNS Please check if the DNS server address is correct at Network tab There is an error message shown as Maximum user exceeded at the remote software In order to assure of system stability DVR has the limitation on the number of remote connection Please check how many users are in connection to the DVR For your information the number of connection from IE amp MMS is also2. When the system asks User amp Password input them which has the rights to system shutdown Note User can input password by virtual keyboard or front numeric buttons if available 2 Operation 2 1 User Log in Check the power connection Input USER and PASSWORD for login after turning on the system The factory default of user and password are ADMIN and 1234 respectively Admin user is to fully control the entire DVR system Note 1 LOGIN window will be permanently displayed in monitor as above picture until user logs in with the correct ID and password 2 If DVR is set as AUTO LOGIN login process is not necessary Please refer to the Section 3 1 2 User for details 5 2 2 Live Display Mode 2 2 1 Channel Selection Real time live image can be seen by easy button operation after power on The images can be seen on real time by 1 4 9 screen Whenever the up down arrow button on the front panel or IR remote controller is pressed the screen mode will be changed sequentially And whenever the left right arrow button on the front panel or IR remote controller is pressed the screen display will be sequentially changed To select a channel amp see as 1 Ch mode make double click of the left mouse button To return previous screen mode after selecting certain full channel make another double click of the left mouse button Note To properly select channel by mouse user is supposed to make slow and cl
3. INTENSIVE RECODING When alarm is triggered system instantly assigns remaining fps to alarm triggered channel and increases recording speed during the selected dwell time and also will trigger alarm signal via the selected sensor out channel The recording speed of all other channel will remain unchanged DWELL Post Alarm Set the recording period from the start of alarm activation During this period the corresponding camera image will record according to the frame and alarm relay output set The recording stops and alarm output is turned off when the setting period is elapsed PRE ALARM Set recording period in seconds just before perceiving motion alarm The system records in certain seconds of time prior to the time that alarm is activated so that user can search video even before alarm is triggered The pre alarm recording mode is always continuous at the recording speed that user sets in record of camera menu NOTIFY User can select how to be alerted upon motion is detected by pressing NOTIFY button The system will generate buzzer sound in the selection of buzzer and or make pop up screen of the camera in the selection of camera pop up And both notifications work together when All is selected 36 3 2 5 Extra Alarm There are several alarm functions available on the system such as SMART VIDEO LOSS RECORDING FAILURE and HDD FULL S M A R T It is to trigger alarm signal when HDD mi
4. to confirm whether you can use such domain name 2 In case of DYNDNS COM input full domain that was generated at dyndns com e USER If you use DYNDNS com input user ID registered at dyndns com e PASSWORD If you use DYNDNS COM input password registered at dyndns com Note It takes a little time to check Domain Name If there is no response please check the internet connection of the DVR In order to use DDNS function the accurate DNS server address should be required 47 3 4 3 Router Setting Port Forwarding If user wants to use router for network connection necessary Port Forwarding in the router both static IP and dynamic IP is required The procedure described as below is just one of the example for the reference and the captured figures may differ depending on the model of the router Please refer to the n manual of the socal del details a FO al Aci Parn ppan a 18 D UNK SYSTEMS INC VARELESS ROUTER HOME Windows Internet Explorer ole Gi a E eM gt le 192 1680 112 3 21 xo a P savti de MEP SRH MAV AN RA INM MAH mep FAL IRG le SHER g gmail Google SSE uf Wedhard English Has p ansa e AP Ame H racer 22 20RD Goo D LINK SYSTEMS INC WIRELESS ROUTER H A M S m RA RS IRO to vente Mera in dor Y e me t Mo gt Doe serna re in tas e D 0 lee boone for hosting online services such as FTP or Web Servers a ee mae cits nate a e _ _DonitSave Settings P
5. GPZ N a A o ee esatr te 1 Login to the router through M S IE browser 2 Go to the menu of ADVANCED gt Port Forwarding 3 Do necessary Port Forwarding as below TCP Port Mobile Port amp Web Port eo For TCP IP Port of DVR If you use 9010 for TCP IP Port mentioned as above then you have to forward Port 9010 to DVR LAN IP Name Public Port DVR data port Application Name 9010 9010 Any v IP Address Private Port 192 168 0 164 Computer Name v 9010 w OL Note If you change DVR TCP IP Port to 9020 you have to open and do Port Forwarding for 9020 eo For Mobile Port of DVR If you use 9011 for Mobile Port mentioned as above you have to forward Port 9011 to DVR LAN IP Name Public Port DVR mobile port Application Name 9011 9011 Any v IP Address Private Port 192 168 0 164 Computer Name v 9011 aw Note If you change DVR Mobile Port to 9021 you have to open and do Port Forwarding for 9021 48 eo For Web Port of DVR If you use 80 for Web Port mentioned as above you have to forward Port 80 to DVR LAN IP Name Pan Public Port DVR web port lt lt Application Name v 80 80 o Any wv IP Address e Private Port 192 168 0 164 lt lt Computer Name v 80 Note If you change DVR Web Port to 8080 you have to open and do Port Forwarding for 8080 DVR needs several ports to be opened for remote image transmission configuration time synchronization and
6. OFF in SENSOR of DEVICE and sets SENSOR in SCHEDULE then the system will not record anything even though a sensor is triggered SKY BLUE COLOR Continuous Motion Detection Recording The system records all the time by continuous as set by CAMERA of RECORD but will switch recording mode to motion configuration as made by MOTION ALARM of DEVICE if motion is detected in motion area The system also will notify motion event message to Remote Software over the network If user sets OFF in MOTION ALARM of DEVICE and sets CONT MOT in SCHEDULE then the system will record with continuous recording mode even though motion is detected in motion area 42 DARK ORANGE COLOR Continuous Sensor Activated Recording The system records all the time by continuous as set by CAMERA of RECORD but will switch recording mode to sensor configuration as made by SENSOR of DEVICE if a sensor is triggered during dwell time The system also will notify sensor event message to Remote Software over the network If user sets OFF in SENSOR of DEVICE and sets CONT SENS in SCHEDULE then the system will record with continuous recording mode even though a sensor is triggered PINK COLOR Motion Detection Sensor Activated Recording The system does not record in normal operation but records only when motion is
7. contact POS manufacturer for the detail v Custom It can be used except the above general character Only number 0 9 and alphabet A F can be used and even numbers should be inputted ex Hexadecimal OxOD Ox0A ODOA SAVE Select to save POS data LINE DISPLAY SETTINGS e DISPLAY LINE Set the number of line to be displayed on the screen e CLEAR TIME Set the period to be displayed on the screen The data will be deleted if no more data is inputted after passing the setting time here If it is set as 0 the data will not be deleted If there is Start Character and the character is inputted current data will be deleted regardless of the Clear Time setting e POSITION Designate the display position of POS data e FONT COLOR Select the font color which will be displayed on the screen It will be displayed with the color that is shown on SAMPLE TEXT eo SHOW Select to display POS data in the live mode e SCROLL REVERSE Select to change the direction of scrolling If it is selected you can scroll from the bottom to top that is the latest data is displayed on the top 99 PLAYBACK DISPLAY SETTINGS e DISPLAY LINE Set the number of line to be displayed on the screen e CLEAR TIME Set the period to be displayed on the screen The data will be deleted if no more data is inputted after passing the setting time here If it is set as 0 the data will not be deleted e POSITION Desi
8. playback It is easy to use USB mouse or the Front Panel s Jog Shuttle to playback recording files Turn the Jog and the recorded files can be seen backwards or forwards Turn the Shuttle and the playback speed can be controlled 2 4 8 16 32 times gt O backwards or forwards User can click the right forwarded arrow button to automatically playback the latest video clip In playback screen user can make various playback modes make an instant manual backup archive go to calendar search mode change channel and change screen modes User can make a click of the left mouse button in colored time bar to move white vertical line that represents playback time 2 10 Quick Backup during Playback User can easily archive video while he she watches video playback In playback mode user can press ENTER button in the front panel to set archive start time After pressing this ENTER button user will see Quick backup starts in right bottom of the playback monitor Once Quick backup starts message is shown user can keep playing back video until user wants to finish archiving and then press the same ENTER button again to set backup end time Then backup menu window will be popped up and user can select the backup media like CD DVD or USB thumb drive and execute archiving Press ENTER button to set start and end time during video playback Button type may be different depending on
9. the DVR case Note HELP button can help you understand how to setup several important settings For example if you need help about how to set Backup click HELP button at the right bottom of the menu 15 2 11 Search Recorded Image The user can search recorded image by clicking the right mouse button and select Search button or clicking Tool button in the menu bar and select Search button 2 11 1 Calendar Search The user can select date and time to search for a certain image within the recorded image User can move the white vertical line to the time that user wants to search The colors of the time bar are different by each recording mode Please refer to section 3 3 2 for details on colors Time bars in color shows by 4channel group mark in date as above picture means that there is a video data recorded 2 11 2 Search Date Time Enter the desired date and time for the user to playback the recorded image Use the arrow button to move to each day month year and time category for selecting second minute hour month year 16 2 11 3 First Data Go to the first screen of the recorded image This is the oldest image recorded gt gt zo 12 F0107 18 2 11 4 Last Data Go to the last screen of the recorded image This is the latest image recorded E 2 11 5 System Log The system log search is used to find particular system log information quickly and easily User can copy this
10. Digital Video Surveillance System HD SDI User Manual The picture functions amp supplied items might differ according to the specification and model x Contents of this user manual are protected under copyrights and computer program laws DVR H 264 HD SDI DVR 1 Edition 31 Dec 2012 Thank You Before operating the system please read this User Manual and retain it for future reference WARNING TO REDUCE FIRE OR SHOCK HAZARD DO NOT EXPOSE THE UNIT TO RAIN OR MOISTURE The installation should be made by a qualified service person and conformed to all local codes Cautions Read Before System Operation Follow these details to prevent material damage or personal injury Signs of Caution and Warning A Warning This sign indicates that the user could die or be seriously wounded if not used or installed properly Caution This sign indicates that the user could be wounded or could expect property damage if not used or installed properly A Warning Do not expose the product to fog rain or too much humid to decrease danger from electric shock or fire General Warning A Warning 1 Use the power cord which is supplied or recommended by the supplier or it may cause fire 2 Do not disassemble or reassemble the product It may cause malfunction or fire 3 Enquire to your vendor for repair It may cause electric shock or fire if the repair is not done properly 4 Do not touch the product with wet han
11. General setting structure consists of System Device Record Network Backup and Quick Setup as below Main Classification Sub Classification SYSTEM INFO USER SYSTEM EXPORT IMPORT HDD FACTORY DEFAULT CAMERA AUDIO SENSOR DEVICE MOTION ALARM EXTRA ALARM PTZ CAMERA RECORD SCHEDULE NETWORK DDNS NETWORK NOTIFICATION POS MANUAL BACKUP BACKUP INSTANT BACKUP QUICK SETUP QUICK SETUP 3 1 System User can find the menu button in TOOL of the menu bar or pop up menu of mouse right button User can move mouse pointer from System through Quick Setup to instantly look around the sub menus in the menu screen OS Eu x gt aby L ee Lao ts 4 22 3 1 1 System Info SITE NAME User can designate the site name by using virtual keyboard as below Site name will be used as a folder name for back up the data or log a A be Ne oa gt F lt gt i d b A 1 1 09 0 Vp ae ae l a x SITE ID User must setup SITE ID to match with the ID setting of keyboard controller if user wants to use it to control DVR User also needs to select the correct model of keyboard controller and BUAD RATE setting DATE TIME User can make various settings such as time zone selection DST Daylight Saving Time and time sync mode 23 Note HELP button can help you understand how to setup severa
12. II A II A ae ere ee 38 O O a a 44 So PA KUP o N E A A 56 SO E S TOPE N NN lada 58 1 Getting Started 1 1 Checking Supplied Items Make sure that you have following items supplied with your DVR If any of these items is missing or damaged notify your vendor immediately Keep the packing utilities for moving or storage purposes afterwards User Manual and iar Remote Software we 12V D C Adaptor ji and Power Cable IR Remote Controller 3 i 1 Set Type of controller may differ depending on the DVR model Terminal Block 1 Pair 2 Pieces and Rubber Mount 1 Set 4 Pieces Packed goods may differ depending on the DVR model 3 1 2 System Startup After connecting all peripheral devices connect power cord to the DVR for system startup Input USER and PASSWORD for login after turning on the system The factory default of user and password are ADMIN and 1234 respectively Admin user is to fully control the entire DVR system Note 1 Do not forget the administrator s password that was set for the first time In case the password is forgot contact your local dealer for help 2 Refer to the Section 3 1 2 User for AUTO LOGIN and AUTO LOGOFF 1 3 System Shutdown To turn off the power click TOOL button and then click SHUTDOWN in the GUI software as below Do not pull off the power by pulling the power plug e gt 19190 s Y v2H 2012 19 aora ES PEA aE ae d
13. OBILE PORT Input the mobile port number to use when connecting from mobile devices It is for use with Mobile Software MMS of Windows Mobile or Blackberry It is also for use with MobileViewer 1 of Android or lOS iPhone iPad In case of MobileViewer 2 or higher version TCP IP Port is used instead of MOBILE Port WEB PORT Input the port number to use when connecting from the Web Browser UPnP Universal Plug and Play UPnP supports auto port forward function NAT TRAVERSAL even if the user does not set port forward in the router It may not be supported in some routers and some network conditions 45 BANDWIDTH LIMIT Depending on the setting made by user the system can control the data volume transmitted over network ranging from 25 kbps up to 1Gbps This function is effective especially under narrow bandwidth network condition or when user wants to limit network bandwidth occupied by video transmission to a certain level 2 oo E 7 ii r EE gt r 7 M 11 9 Wo Fp a A Input necessary information based on your network environment and then click SAVE button NETWORK TYPE IP ADDRESS SUBNET MASK GATEWAY DNS SERVER TCPAP PORT MOBILE PORT WEB PORT Select STATIC IP in case of fixed IP Assign a local IP to DVR ex 192 168 0 164 Input subnet mask of your LAN ex 255 255 255 0 Input gateway of your LAN ex 192 168 0 1 Input IP of your DNS server You must input thi
14. are COVERT If a channel is set as COVERT no other users except administrator can see the image in live amp playback mode It is applied to both DVR and remote monitoring software MOTION AREA User can select motion detection area and sensitivity The area can be selected by clicking block or drag of the mouse Note Motion detection area and sensitivity should be set properly in consideration of the actual motion happened in the site 32 3 2 2 Audio User can select audio input and output during live display and match the audio input to a designated channel Number of audio channel may differ depending on DVR model USE 2 WAY AUDIO lt is an option to make the voice communication between DVR and remote software available Audio out of the DVR outputs the audio voice from the remote software In the remote software user can listen the audio voice of the selected channel once the user activate 2 way audio function at the remote software Note Depends on the condition audio output channel is different Live Mode 1 1 Screen Mode Audio of the currently displayed channel 2 Multi Screen Mode Audio of the audio channel that is set at LIVE Playback Mode 1 1 Screen Mode Audio of the currently displayed channel 2 Multi Screen Mode Audio output is not available 33 3 2 3 Sensor It allows user to set alarm generation when the external sensor device connected to the DVR detects signal User can i
15. auses but system clock date time information continues running Open pop up menu by right click on the mouse and select the FREEZE mode again to resume the live view 2 6 ADD BOOKMARK Click Bookmark button to save the information on the current showing image including description in live amp playback mode 11 2 7 PTZ Operation User can get into PTZ mode by clicking right mouse button and selecting PTZ in the pop up menu as below or select joystick button screen in the menu bar appeared in the bottom of the main In PTZ mode user can control PTZ operation with the mouse While pressing the left button of mouse user can drag the mouse pointer to up down or left rightward to move pan tilt position of the camera If user moves the mouse pointer long away from the center position of the main screen the PTZ camera moves at faster speed in case that the PTZ camera support speed control function User can also move zoom in out by rolling the mouse wheel to up or downward Note Full PTZ functions are available by using mouse IR remote control or keyboard controller For focus control in PTZ screen mode user can click right mouse button again to get the pop up menu as below picture Default mode is to tick ZOOM Thus user can tick FOCUS to switch the wheel function of mouse from zoom in out to focus Then user can control focus by moving the wheel of mouse In the same way user can se
16. ays continuous at the recording speed that user sets in record of camera menu TYPE Select the sensor type between N O Normal Open and N C Normal Close connecting to alarm input plate Circuit of N O type is usually open and the activation of the sensor occurs at the time of close and N C type works the reverse way NOTIFY User can select how to be alerted upon sensor is activated by pressing NOTIFY button The system will generate buzzer sound in the selection of buzzer and or make pop up screen of the camera in the selection of camera pop up And both notifications work together when All is selected Note Check the setting of the sensor type N O or N C The alarm might not function if the used sensor type and the system setting are inconsistent Note Camera pop up means that multi screen live video mode will be switched to single channel mode automatically upon alarm triggered This single channel video is the channel triggered by alarm 35 3 2 4 Motion Alarm Motion alarm is to start the recording when motion is detected by installed camera based on the area setting The system will trigger alarm signal via the selected sensor out channel ON OFF Turn on or turn off the motion alarm OUT Select the associated alarm output Caution Relay contact can stand up to 24V 1A In case that it is connected to the external circuit which is over 24V 1A it can cause a problem on the system
17. detected as set by MOTION of DEVICE and a sensor is triggered as set by SENSOR of DEVICE If user set OFF in both MOTION of DEVICE and SENSOR of DEVICE then the system will record only when the motion is detected but will not record even though a sensor is triggered And the system will not notify both motion 4 sensor to Remote Software Note Incase the recording schedule is set by CONT MOT or MOT SENS then the system records by continuous or motion detection mode in normal operation However when motion is occurred in motion area or alarm is activated then recording mode will be automatically switched to intensive recording as set by MOTION or SENSOR of DEVICE menu Note Dark Blue Color The data recorded during DST Daylight Saving Time will be indicated in Dark Blue color in Intelli Search Bar on playback mode 43 User can add holiday in HOLIDAY SETUP as below picture to up 32 holidays Press DATE first and write description and then press ADD button to list up holiday Note Emergency Recording In case of a specific model that has Emergency recording button in front face the system will instantly start recording all the channels with its maximum frame rate in total amp highest resolution when a the Emergency recording button User can do the same with Cross icon button in the Tool bar All the channels regardless o
18. ds It may cause malfunction or electric shock 5 Product installation must be ensured to a professional for product installation or it may cause malfunction electric shock or fire 6 Ground applies to video products equipped with a 3 wire grounding type plug having a third grounding pin This plug only fits into a grounding type power outlet If grounding is not done it may cause malfunction or electric shock 7 Ground connection must not touch gas pipe water pipe or telephone line If grounding is not done properly it may cause electric shock 8 Prevent metallic foreign substance from going inside the product It may cause malfunction or electric shock 9 Do not spray insecticide or flammable spray while driving It may cause fire 10 Place the system in a open place where air ventilation is guaranteed or it may cause over heating and seriously damage the system to be fired 11 Prevent water from instilling inside electrical parts Clean with a dry towel or malfunction or electric shock could result A Caution 1 Use the power cord which is supplied or recommended by the supplier The internal fan rotates at high speed and may cause an accident 2 Do not drop give strong vibration or shock to the product It may cause malfunction 3 The air inhaler of the front panel and air outlet of the back panel must not be blocked during installation The internal temperature of the product would be greater than allowab
19. e system will not notify alarm upon motion alarm or sensor even though user ticks the check box of above event selection unless user sets the SCHEDULE of RECORD and MOTION SENSOR of DEVICE accordingly For example if user sets just Continuous only in SCHEUDLE of RECORD and tick All check box of REMOTE NOTIFY the system will not notify alarm message In this case user has to set CONT MOT MOTION SENSOR or CON SENS to enable REMOTE NOTIFY properly Note User can set remote pop up in RemoteManager S W RMS and Central Management S W CMS upon alarm trigger in DVR In order for RMS or CMS user to receive an instant pop up video over network from DVR DVR user has to tick SENSOR or MOTION ALARM in above menu SENSOR means the alarm triggered by physical alarm while MOTION ALARM means the alarm triggered by motion detection Note In order to receive event notification properly event port in the setting menu of the Remote Software PC should be the same to that of in this setting screen Note Incase the Remote software PC is not in the same network port forwarding for the PC should be required to receive remote notify properly 50 E MAIL NOTIFY The system can make an event notification to the e mail address registered in the DVR Select E MAIL NOTIFY to use this function and set e mail address amp events ADD EDIT DELECT User ca
20. ear double click of the left mouse button 2 2 2 Menu Tool Bar When user place USB mouse pointer in the bottom of the monitor in live mode menu tool bar will be instantly appeared as below picture 2012 19492 21 A Fs Sequence button o makes screen display change based on the current display mode sequentially as per time setting Cross icon button means instant emergency recording which is useful to urgently start recording In emergency recording the system records all the channels within its maximum frame rate at D1 resolution Joystick icon button EJ means PTZ mode which is useful to instantly switch to PTZ control In PTZ mode user can control pan tilt by moving the mouse pointer and zoom in out by controlling mouse wheel In order to control focus by mouse wheel click the right mouse button and select Focus User can click the right forwarded arrow button gt to automatically playback the latest video clip Pin icon button means that user can fix this menu bar or disable fixing the menu bar by moving out mouse pointer If user fixes the menu bar then this menu will not disappear even though user moves away mouse pointer out of this range If user does not fix the menu bar then the menu will be shown when user places mouse pointer in this bottom area only Circle icon button means the HDD usage percentage by video recording If it shows 60 then 60 of HDD space has been used up for rec
21. een of MultiBackup Player as shown picture to begin video play In the left box files amp folders saved in the PC are shown Note Single Channel Mode It shows SSF files in a selected folder Multi Channel Mode It shows SSF files and folders in the PC User can print out capture a still image and zoom out by using the icons on the bottom left of the player window 58 3 6 Quick Setup Quick Setup is to help user make easy configuration for recording resolution recording speed recording mode recording quality and recording periods based on the capacity of HDD installed The setting made by QUICK SETUP will get the first priority to apply on the system whatever user sets configurations in other menu USE QUICK SETUP If user ticks in the check box of USE QUICK SETUP and designate the Desired Recording Period the setting value for recording resolution fos and quality will be optimally adjusted to get the similar recording period set in the box of INPUT DESIRED DAYS Furthermore user can adjust the setting value at CUSTOMER SETTINGS by manual input finally to get the Recordable Period at DAYS TO RECORD based on the capacity of HDD installed Note Recordable period calculated by QUICK SETUP is just for reference and may vary depending on the actual site situation Note Ifthe camera is set as OFF in the camera setting menu it will not be recorded even if it is set in the Quick Setup menu Please check i
22. etc Please refer to below port list to make sure that those ports are not blocked by firewall or other network setting lt may differ depending on the model of the router Please refer to the manual of the router for details Usage Remark _ _ _ Editable Location DVR Data Port for Remote S W DVR Mobile Port Y Mobile Viewer Mobile Port If DVR works as the Sven inio DVR Time Sync client port should be y 8002 gt Date Time Service Port opened at the server Setti e etting Network TCP Port gt Network Network gt Network 8003 Event Port for Event Need port forward at Notify remote P C network gt Notification Network ne 80 8245 DDNS Server Need to be opened Select ee System Info NTP Server Need to be opened Fixed gt Date Time Setting 49 3 4 4 Notification REMOTE NOTIFY The system can notify an event to the IP address of Remote Software PC over the network Select REMOTE NOTIFY to use this function and set IP address amp events ADD EDIT DELECT User can use these to add edit delete IP address of Remote Software PC IP ADDRESS Input the IP address of Remote Software PC which will receive events notification PORT Input Port number which is set at the Remote Software PC Default is 8003 EVENT Select events to be notified When ALL is selected all of the events will be notified Note Configuration first priority is always on SCHEDULE of RECORD Thus th
23. event list to USB memory device in text file format Once USB memory stick is put via USB port user must press SCAN button to detect it and then press EXPORT to copy the log information to the media Once export is completed user can find a date folder created in USB thumb drive There is system_ Date log file stored in the date folder Following is the category indicated on the system log viewer 1 Log by system 2 Log by setup 3 Log by network Note 10 numbers of log record will be shown on one page of the System Log and Event Log window User can click the arrow icon to search the log records on another page 7 J 1 To see the corresponding list of System Log and Event Log user needs to click SEARCH button after selecting desired date and event type 2 11 6 Event Log The Event log search is used to find particular event quickly and easily User can copy this event list to USB memory device in text file format Once USB memory stick is put via USB port user must press SCAN button to detect it and then press EXPORT to copy the log information to the media To see particular event of activated time move the arrow button of the Front Panel or Remote Controller to the desired time range Following is the category indicated on the Event Viewer 1 Alarm by Sensor 2 Alarm by Motion 3 Alarm by Video Loss 4 Alarm by HDD Full 2 11 7 POS Input the information ca
24. eze add bookmark search PTZ recording info and move to menu 2 2 5 Video Loss Video Loss is shown on the display screen when no camera is connected or camera is disconnected on a certain channel When camera is disconnected warning sound shall be generated depending on the system setting 12 21 2012 19 57 56 2 2 6 User Add Edit Admin user can set different level of authorization for each user If a certain user is not allowed to view a certain live and playback channel then no image is shown on the display screen as below Note If no camera is connected after system booting the channel is shown as Video Loss If no camera is connected before system booting or no authorized channel the channel is shown with channel logo 2 3 Sequence When SEQUENCE is selected EJ icon is shown on the right bottom corner of the screen and display screen will be sequentially changed Dwell time can be set in the menu System Info gt Display 2 4 Zoom When ZOOM is selected on full screen mode digital zoom function is activated and ZOOM icon is shown on the right bottom corner of the screen In zoom pop up menu user can select ZOOM IN or ZOOM OUT and exit to normal live display mode by selecting ZOOM EXIT User also can use mouse wheel to control zoom in out 2 5 Freeze Mode Click the right mouse button and select the FREEZE mode on pop up menu while viewing live image then live image p
25. f recording mode amp recording on off are to be recorded is shown in live mode and red colored bar is shown in the time search bar of playback mode for the video recorded by emergency recording 44 3 4 Network DVR can be connected to network or internet through either fixed IP or dynamic IP by proper setting of DVR amp router 3 4 1 Network NETWORK TYPE Select either STATIC IP or DHCP for dynamic IP If DHCP is selected click IP DETECT button to get the updated IP address information then you can see the process on Progress Bar SUBNET MASK Subnet Mask address classifies the subnet that the system belongs to For more information please consult your network administrator or your internet provider GATEWAY This is the IP address of the network router or gateway server It is required when the user wants to connect through external router For more information please consult your network administrator or your internet provider DNS SERVER Enter the IP address of the Domain Name Server You should input the DNS Server information in order to use DDNS E mail notify and NTP Server If it is hard to know the correct information user can input 8 8 8 8 For more information please consult your network administrator or your internet provider TCP IP PORT Input the port number to use when connecting locally or remotely It is for use with Remote Software P C RMS amp CMS amp mobile device MMS M
26. f any of camera is not recorded 59 QUA There is a HDD installed but No HDD con MA2B is still shown on the screen 1 Please check the cable connection of the HDD again 2 If you can see the HDD list at System gt HDD but the capacity indicates 0 it means that the HDD requires format There is nothing displayed on the monitor though electric power is supplied to DVR 1 Please check if the power is supplied properly When the power is supplied you can hear the noise from FAN and HDD operation 2 Please check the cable connection with the DVR Remove all the cable connections except for the monitor cable and then apply power to the DVR again and check booting status 3 Incase that the display screen is stopped at logo screen H 264 Digital Video Surveillance System please contact your dealer or distributor How to make PPPoE connection xDSL cable and so on 1 There is no function to log in at the DVR 1 Please use the router which supports PPPoE log in Is it necessary to open the port when using DDNS cctv link net dyndns org Yes it is DDNS is the function to let remote software acknowledge the changed address of the DVR dynamic IP provided by ISP or to allow connection to the DVR by sub domain sub domain cctv link net without memorizing IP Remote software connection to the DVR works fine but WEB connection doesn t work 1 Some ISP blocks port number 80 Please try aga
27. ght be about to be out of operation VIDEO LOSS It is to trigger alarm signal when the camera signal is disconnected RECORDING FAILURE It is to trigger alarm signal when the system doesn t record image due to the error in HDD or system and so on DISK FULL It is to trigger alarm signal when the HDD is occupied with a certain percentage of its capacity If user set HDD FULL as STOP RECORDING in HDD menu and the HDD is occupied with the certain percentage set here DVR stops recording and alarm trigger Note Extra alarm will be remained in the event log only when it is set as ON Note S M A R T Self Monitoring Analysis and Reporting Technology is the technology that is developed by HDD manufacturers In some cases S M A R T may not detect the abnormal operation of the HDD It is recommended to do HDD health check in the HDD menu regularly 37 3 2 6 PTZ Check the below items for proper P T Z operation e Check if the protocol of the connected PTZ camera is correct e Check if the communication setting including baud rate of the connected PTZ camera is in accordance with the assigned value for that P T Z protocol e Check if the address of the connected PTZ camera is correct e Check if wiring to P T Z controllers is correct Procedure How to setup PTZ camera with Pelco D protocol example 1 Make sure of serial communication with the PTZ camera through RS 485 port 2 Select Pelco D in the protocol list and
28. gnate the display position of POS data e FONT COLOR Select the font color which will be displayed on the screen It will be displayed with the color that is shown on SAMPLE TEXT o SHOW Select to display POS data in the live mode e SCROLL REVERSE Select to change the direction of scrolling If it is selected you can scroll from the bottom to top that is the latest data is displayed on the top PORT SETUP TYPE Setup the type of communication port Y SERIAL ltis for 1 to 1 connection between DVR and POS device without Serial MUX v MUX It is for 1 to Multi connection between DVR and POS devices BAUDRATE Set BAUDRATE according to the connected POS device PARITY Set PARITY according to the connected POS device DATABIT Set DATABIT according to the connected POS device STOPBIT Set STOPBIT according to the connected POS device TCPAP Port Set TCP IP Port according to the connected POS device 56 3 5 Backup 3 5 1 Manual Backup User can archive video clip recorded for certain period for a selected channel or channels as below picture Connect an appropriate USB memory device like USB thumb drive built in CD or USB ODD burner and press SCAN button to get the system recognize it before actual archiving Necessary file size will be shown before burning User can leave ticking in the check box of ADD VIEWER to automatically put in an executable viewer file of SSF format in order to help user p
29. in after changing WEB port 8080 or 8088 is recommended 2 Please check whether the WEB port is opened or not Image is not shown after login at WEB monitoring TCP Base port should be opened Default of TCP base port is 9010 No image is shown on MMS connection Mobile port has to be opened for MMS connection In case of MobileViewer 1 Mobile Port that is set in the network menu should be used In case of MobileViewer 2 or higher version TCP IP Port is used instead of Moblie Port DVR doesn t record images in sensor mode and or motion mode 2 It records images only when there is an event for the corresponding mode 2 Please check if the setting is correctly done at the menu of Device gt Sensor and Device gt Motion Image on remote software is suddenly disappeared after displaying for a short time 1 Some ISP restricts upload data traffic volume Please contact your ISP 2 Upload traffic restriction can be easily checked with the following steps gt Turn off the power of Modem amp Router gt After some time 1 5minutes turn on the power of Modem first and then Router gt After reconnection if it is disconnected again after a shot time in a similar period later it means that the ISP restricts upload traffic 10 11 12 13 60 Backup or firmware upgrade through USB memory stick cannot be made though it is detected by the DVR 1 USB memory stick should be formatted by FAT or FAT 32
30. l important settings For example if you need help about how to set Date TIME click HELP button at the right bottom of the menu TIME SYNC MODE There are three types of time sync mode e Server Mode The operating DVR is set as a Time Sync Server which can synchronize the time clock of another DVR s connected over the same network environment e Client Mode The operating DVR is set as one of the client DVR s Input the IP No of designated DVR or RemoteManager P C RMS or Central Management P C CMS as a Time Sync Server in SYNC SERVER then DVR time clock is synchronized with Time Sync Server by interval time set in TIME SYNC CYCLE e NTP Mode NTP server is one of standard time servers available on Internet and it is recommended to use pool ntp org If you want to activate this mode you have to correctly set the TIME ZONE of your local area and then click SYNC NOW LANGUAGE User can select the language according to the country or user s preference The language included in the product according to the model REMOTE ID User must setup REMOTE ID to match with the ID setting of IR remote controller if user wants to use it to control DVR Note How to setup the ID in IR Remote Controller 1 Keep pressing ID selection button for about 5 seconds 2 Set the ID number by pressing numeric button on IR Remote Controller ID number is available from 000 up to 255 3 You have to press numeric button as three digi
31. lay the video clip without installing program in the computer 11 0 1 2012 00 31 48 Note Itis recommended to use built in CD DVD burner or well known major brand of USB thumb drives formatted by FAT FAT 32 for proper backup 1 The system does not detect external HDD due to different format type 2 It is not allowed to use the partitioned and or password encoded USB memory 57 3 5 2 Backup Video Retrieve After archiving there would be multiple files created as the picture below if ADD VIEWER was selected User can double click MultiBackupPlayer exe file and open the video data file SSF format in the folder of date The folder is named by the date recorded amp CDROM E File Edit View Favorites Tools Help gt iT yo Search ES Folders Ez Go Links gt A Files Currently on the CD J Dvri 2009 11 10 2 2 45 File and Folder Tasks 2 s AUTORUN INF 2009 12 06 Q7 12 29 BKPLAYER EXE 2009 12 06 27i 12 29 CA BKPLAYER ICO 2009 12 06 24 12 29 ia Share this Folder E MYAVCD DLL 2009 12 06 27i 12 29 gt E SADPCMV2 DLL 2009 12 06 2541 12 29 A E SG723DEC DLL 2009 12 06 24 12 29 E SIMGEXPT DLL 2009 12 06 Q7 12 29 My Computer E SM4VDEC DLL 2009 12 06 Q7 12 29 E My Documents Shared Documents My Netwnrk Plares Publish this Folder to the Web Details The Backup player supports two modes O MuULTICH y User can drag and drop a SSF file Video data file in the empty scr
32. le and could cause malfunction or fire 4 Do not touch the product or the power cord when there is thunder It may cause electric shock 5 Do not install the product near or on top of heating source The internal temperature of the product would be greater than allowable and could cause malfunction or fire 6 Do not install the product on inclined or unstable location or where vibration could be committed It may cause malfunction Cautions about the Power AN warning 1 Must use the outlet of the grounding to connect the power cord or it may cause fire 2 Do not connect on the middle of power cord or use extension cord It may generate heat or cause fire 3 Do not touch the power cord with wet hands It may cause electric shock 4 Keep power cord dry and protect from humidity It may generate heat or cause fire The power cord is not waterproof 5 Hold the body of the plug while removing the power plug Do not pull the power cord Damage to the power cord may generate heat or cause fire 6 Check the power plug regularly Humidity and moderation in smoking may cause fire 7 Remove power cord from outlet when product is not used for a long time It may cause short circuit or electric shock LN Caution 1 Do not turn off the power by removal of the power plug To turn off the power click the power button from the front panel When the system stops abnormally the power button might not work Click power button fo
33. lect preset button or exit PTZ screen mode Note User can select Preset number with virtual keypad once after user set a PTZ protocol in setting menu Maximum Preset number is 255 but it can be restricted by the number that PTZ camera supports User can automatically switch PTZ camera position according to the sequence of preset setting by using GUARD TOUR function though the connected PTZ camera does not support it GUARD TOUR on the pop up menu can be enabled after changing to full screen for the channel that the PTZ camera is connected to Please make sure that PTZ camera setting is correct otherwise GUARD TOUR is shown as disabled Caution Interval time can be set in between 5seconds and 30seconds according to preset Depending on PTZ camera some preset positions might be skipped in the case that the PTZ camera cannot mechanically move or control focus within the interval time set by DVR In this case it is recommended to make setting of interval time a little longer Guard Tour function might require DVR rebooting or preset change 13 2 8 Recording Info Click the right mouse button and select the RECORDING INFO on pop up menu while viewing live image Then user can check detail information on image recording 2 9 Playback Recorded Images To playback recorded image press Play button from the Front Panel or IR Remote Controller When the Play button is pressed the latest recording image will be
34. mera date amp time keyword and click SEARCH button Then it will display the recorded data include POS data If no keyword is inputted the system will display all data during that time Select one of the list and click PLAY button to display the relevant video image with POS data 2 11 8 BOOKMARK It can be checked modified and deleted the bookmark data Select one of list and click PLAY button to display the relevant image video Note User can press SEARCH button in the front panel to get the SEARCH pop up menu as below In this menu full search function by using front key buttons is available 20 2 12 DST Setting and Image Playback During DST Daylight Saving Time period DVR time clock has to be adjusted according to regional time zone That is DVR time clock will be shifted by one hour after DST setting while DVR will restore the time clock to normal after DST finishes To make DST setting on the DVR go to the menu of SYSTEM gt SYSTEM INFO and click DATE TIME to get the DST setting window as below User can setup DST Begin amp End time after checking USE DST box There is an hour overlapped data when DST finishes Such period of hour will be indicated in Blue color in Intelli Search Bar on playback mode When user click on such overlapped period a message of Data Selection will pop up then user can select whether to play DST data or Non DST data 21 3 Setting
35. n the contrary the higher percentage requires the bigger network bandwidth but the image quality will be better The highest image quality 100 is same to the standard image quality of record setting Note Frame assignment is not made by total frame but by chip unit Therefore remaining FPS shows per chip 41 3 3 2 Schedule Set recording schedule for each camera First select the camera to set schedule or All Recording can be set by each hour from 00 through 23 a day SCHEDULE NO COLOR Off Off means no recording Even though user set recording frames and on in CAMERA the system will not record anything if user sets OFF in SCHEDULE YELLOW COLOR Continuous Recording In continuous recording mode the system records all the time as set by CAMERA GREEN COLOR Motion Detection Recording In this mode the system records only when motion is detected in the motion area and stops recording when motion is not occurred In addition user can make motion recording configuration in MOTION ALARM of DEVICE menu If user sets OFF in MOTION ALARM of DEVICE and sets MOTION in SCHEDULE then the system will record when motion is detected but motion alarm will not be activated ORANGE COLOR Sensor Activated Recording In sensor mode the system will record when sensor is triggered only during dwell time as set in SENSOR of DEVICE menu If user sets
36. n use these to add edit delete e mail address E MAIL Input e mail address which will receive events notification EVENT Select events to be notified When ALL is selected all of the events will be notified SENDER Setting SMTP Setting User needs to set sender to send e mail notification eo SMTP Input SMTP server address e PORT Input Port number that will be used for e mail sending e USER Input User in case the log in is required to SMTP server e PASSWORD Input Password in case the log in is required to SMTP server o FROM Input sender s e mail address e E MAIL TEST User can check if setting is done properly or not DVR sends e mail and inform you of the result 1 It may take long depending on the SMTP server s response time 2 In some cases SMTP server does not send e mail even though the test result is OK Thus please check at the receiver s e mail if it receives the mail or not USE SSL AUTHENTICATION In case the SMTP server requires SSL authentication ex Gmail Yahoo mail etc select it to send e mail after log in with SSL authentication Note Configuration first priority is always on SCHEDULE of RECORD Thus the system will not email alarm message upon motion alarm or sensor even though user ticks the check box of above event selection unless user sets the SCHEDULE of RECORD and MOTION SENSOR of DEVICE accordingly For example If user sets jus
37. nstall multiple sensors on the system to get the pre amp post alarm recording and intensive recording function as well E E a 24 2 de ON OFF Turn on or turn off the sensor CAM Select the associated camera OUT Select the associated alarm output Caution Relay contact can stand up to 24V 1A In case that it is connected to the external circuit which is over 24V 1A it can cause a problem on the system INTENSIVE RECODING When alarm is triggered system instantly assigns remaining fps to alarm triggered channel and increases recording speed during the selected dwell time and also will trigger alarm signal via the selected sensor out channel The recording speed of all other channel will remain unchanged PRESET User can select the camera to move to preset position once the sensor is triggered User should setup preset position in PTZ menu 3 2 6 in advance DWELL Post Alarm Set the recording period from the start of sensor input activation During this period the corresponding camera image will record according to the frame and alarm relay output set The recording stops and alarm output is turned off when the setting period is elapsed 34 PRE ALARM Set recording period in seconds just before perceiving sensor input The system records in certain seconds of time prior to the time that alarm is activated so that user can search video even before alarm is triggered The pre alarm recording mode is alw
38. on cannot be changed and the recording resolution is decided by camera input FPS lt means Frame consisting even and odd fields per second The system automatically calculates Remaining FPS per chipset QUALITY The setting value of Quality directly influences the byte size per image For example the byte size decreases as quality goes lower In this case blocking mosaic phenomena tends to appear which is resulted by high compression In contrast blocking phenomena disappears as quality goes higher In this case the required storage space per image increases which leads to shortening of total recording period Therefore give consideration to the necessary recording period importance of each camera image and quality of signal when setting the recording quality 39 AUTO DEL Auto Delete lt means that the system will delete video whatever is recorded longer than the number of days set by Auto Del in accordance with privacy regulation in certain country CANCEL H do A i M 11 0 geo T AA A m aS Note Auto Del does not guarantee the number of recording days user set For example even though user sets 10days in Auto Del if HDD space is not enough then the system can not record up to 10days This feature is not to keep video data for a certain number of days set by user If user sets 10days in Auto Del on August 20 for the system that has for example 30days of video da
39. onitoring screen 26 3 1 2 User The ADMIN user default password is 1234 has got the full authority for system setting and can change the system password or assign different permission level to each user FUNCTION shutdown search PTZ control backup and playback MENU ACCESS system device record network backup and quick setup LIVE amp PLAYBACK live amp playback channel E 20 3 D gl Note Total number of users including administrator is 16 Click OPTION button to make setting of Auto Login amp Auto Logoff function AUTO LOGON and AUTO LOGOFF If user selects On Boot DVR does not request to input ID and Password during system rebooting On the contrary if user selects Auto Logoff and sets the time DVR will go to live display mode just after the setting time User has to login again by input of ID and Password to control the DVR 27 LEVEL OF USER AUTHORIZATION The administrator can control full function of the system and add the New User with a different authorized level and also delete edit User details e Setting Authorized Level at DVR Go to the menu of SYSTEM gt USER and click ADD You can add or edit user details Example How to set a User with Live Monitoring only Add a new user name description and password Disable all options in FUNCTION and MENU ACCESS In LIVE amp PLAYBACK select channel s for live monitoring and click OK A new use
40. ording Usage percentage Is displayed by 5 unit 7 2 2 3 Icons In real time live mode icons or messages will be indicated on the screen to notify the system mode or status Below are the icon categories which are indicated on the monitor Icon to be shown at right upper corner on each channel screen Icon to be shown at right bottom corner on full screen No HDD Smart Alarm amp HDD Failure Motion Detection Recording Using Emergency Recording Continuous Recording Sensor Activating Recording Using PTZ Continuous Motion Alarm Warning for exceeding Recording temperature Continuous Sensor Activating l Recording Motion Detection Sensor Activating Recording Showing sequence mode Showing digital zoom mode Emergency Recording Sensor Activated Motion Detected Audio Connected Channel PTZ Camera Connected Channel E POS Connected Note If you can t find any recording icon in the right up corner of the live screen mode it means that the system does not record any image In this case you need to check recording schedule or camera of the main setup menu But if you turned off the OSD in the System Information Menu the recording icon is not shown even if it is being recorded 2 2 4 Pop up Menu User can click the right mouse button to pop up the menu as below With this pop up menu user can use various functions display mode change sequence zoom fre
41. r 5 full seconds to turn power off 2 Do not cut off the power artificially or give shock or vibration to unit while the hard disk is activating It may cause hard disk failure or loss of data A Remarks Xx Pictures and buttons are subject to be changed or modified up to different models x Function or configuration is subject to be changed or modified without prior notice for improvement of the product Contents Ta GETTING STARTED o e detec o N 2 Ll CHECKING SUPRUIE DO IMEM Serrat nario 2 t2 SYSTEMS TARO eee an ee ee a ee eee eee a ee ar a ee eee ee ee 3 L3 NS TENSHI DOWN li a ia e clan ano lana melo 3 Zu OPERATION 0 20 A ba 4 2 NUSERLOG Nico e ria e a de o oras 4 2 NAIVE IDISPIAY MODE e ia coda da E 5 2 CO EQUENO Eos ico A dci Beran TEM OTR 9 ZA ON o oe cau 10 2 FREEZE MODE merone UREN ECE PUN CEE ORME eo PATE OR ORRIN a Re ener albo 10 ZO ADD BOOKMARK a os pe ied aces 10 A ASS RECT eS N A 11 238 RECORDINGINFO nia id dai las 13 2 9 PLAYBACK RECORDED IMAGES cccsccccecccecccceccccececcecuccececaucucuececuuaecsuaecuuaeuucausecsuaesauaeesuaeeas 13 2 10 QUICK BACKUP DURING PLAYBACK ccccccsccceccecceccccccuccecececcucceceecuccecaucacsueaucesacsueaereseaeeaees 14 2 11 SEARCH RECORDED IMAGE cosas rr RS 15 2212 DST SEFTING ANDUIMAGE PLAYBACK anat ARA A tada 20 5 eel 94 ee en hee ee a SO a ee PE O 21 A sce cts tarts outs sete rata ene A A ceca eae TE A E 21 E O CO Cer ee ae CE 31 e RO 1 E D Dg ren
42. r has been added and click SAVE To verify this limited function go to the menu of TOOL gt USER and login as the User set as above User can get the live images However when user clicks Playback button or select any other function warning message will pop up IPL 11 04 ple a TEI A 28 3 1 3 Export Import User can copy and paste the system configuration values in this menu Export allows user to copy the setting values of this system to USB memory devices Import allows user to call up the setting values of other system from CD DVD USB memory devices During import process make sure that the F W version of source DVR has to be the same as the one of target DVR which user wants to import setting values to If user imports the setting value from the system which is in the same network there will be IP confliction Therefore IP setting should be changed after import procedure e A 28 AS A 3 1 4 HDD User can select Overwrite or Stop recording when HDD becomes full and also can easily format new HDD or existing HDD by ticking in the check box 29 HEALTH Click CHECK button of each HDD to open the window of DVR HEALTH CHECK User can see full information of each HDD such as model name serial no capacity bad sector ratio life time used time and temperature HDD FORMAT When the new HDD is installed or there seems to be a problem on the HDD user needs to format the HDD If sys
43. s IP for internet connection Please contact your ISP to get this IP You can input 8 8 8 8 in case you do not know this IP Default is 9010 If your ISP blocks the port 9010 you need to input another valid port number ex 9020 Default is 9011 If your ISP blocks the port 9011 you need to input another valid port number ex 9021 Default is 80 If your ISP blocks the port 80 you need to input another valid web port number ex 8080 BANDWIDTH LIMIT Default is 100 Mbps Select bandwidth limit you want to set in consideration of network condition 46 3 4 2 DDNS User can use either a public DDNS server or the DDNS server operated by DVR maker cctv link net to connect through dynamic IP It is recommended to use maker s DDNS server for stable network connection DDNS SERVER User has to tick on Use DDNS check box The default is CCTV LINK NET and user can select DYNDNS COM by using drop down list cctv link net is the fixed domain name of DDNS server operated by DVR maker while dyndns com is one of public DDNS severs DS 28 se A Input necessary information based on your network environment and then click SAVE button Enable USE DDNS box DDNS SERVER Select CCTV LINK NET or DYNDNS COM TCP IP PORT Default is 80 If your ISP blocks port 80 select 8245 e DOMAIN NAME 1 In case of CCTV LINK NET assign domain name for your DVR ex abc then click CHECK
44. set address amp baud rate 3 Click Save button to confirm this configuration PROTOCOL Select the proper protocol of the connected PTZ camera BAUD RATE User can select the baud rate level from 2 400bps up to 57 600bps ADDRESS Set the P T Z driver address of the connected camera CONTROL When the SET button is clicked OSD menu of the PTZ camera will be shown on the monitor User can set the PTZ such as speed preset tour autopan and so on PRESET The system supports the number of preset from 1 to 255 But it can be restricted by the number that PTZ camera supports 38 3 3 Record 3 3 1 Camera ON OFF It is to switch recording on and off in each channel If recording is not required on the selected channels even when the camera signal is inputted set the recording of the corresponding channel as OFF Then recording of the channel stops without pulling camera BNC cable off ON or OFF can be selected anytime but the default is ON RESOLUTION It shows camera s resolution Recording resolution is as follows e Video type 720P mode DVR records at 1280 720 resolution regardless of camera input If the video type is set as 720P mode but 1080P camera is connected DVR records at 1280 720 resolution by cutting extra size In the menu it is displayed as 1920 1080 e Video type 720P 1080P Auto mode DVR records at 1280 720 1920 1080 resolution according to camera input Recording resoluti
45. t Continuous only in SCHEUDLE of RECORD and tick Al check box of REMOTE NOTIFY then the system will not make email notification In this case user has to set CONT MOT MOTION SENSOR or CON SENS to enable Email Notification properly 51 MOBILE NOTIFY The system can make an event notification to the mobile device registered in the DVR Mobile Push Notification can be set as following steps 1 Go to menu Network gt Notification 2 Click Mobile Notify button on the bottom NOTIFICATION 4 When the mobile device is registered to the DVR correctly it shows in the list Device ID is a unique ID of the mobile device If you want to delete it select the device and click Delete button Then push notification setup in the mobile device will be disabled Note Note 52 Mobile Push Notification function is available only with the iOS iPhone iPad iPod Touch Registration of Mobile Push Notification is available when it is applied at the mobile device Deletion of the list can be available when you click Delete button in the DVR menu or when you select disable of the Push Notify function in the mobile device Maximum number of mobile device to be registered is 50 Push Notification function only works when the DVR amp mobile device has network connection For the detail please refer to MMS manual 53 3 4 5 POS DVR and POS are connec
46. t number format For example press 000 for 0 023 for 23 234 for 234 24 When the ID at the remote controller is inputted and it can communicate with the DVR correctly DVR sounds beep once at the first time VERSION Current firmware version amp MCU H W version of the DVR can be checked By clicking UPGRADE button user can upgrade firmware UPGRADE FIRMWARE User can easily upgrade the system firmware via DVD CD USB Memory Stick FTP server Caution Do not click CANCEL button during firmware upgrade It may cause serious damage on the system Do not turn off the power of the DVR It may cause serious damage on the system and DVR may not be turned on after that The setting value might be changed to that of factory default in case that there area lot of changes between new firmware and existing firmware in functions etc Therefore it is recommended to check the setting value and operating condition of the DVR after firmware upgrade Procedure How to upgrade system firmware by using USB memory stick 1 Put USB thumb drive which was formatted by FAT FAT32 in any USB port of DVR that shall be compatible with USB 2 0 version 2 Once the system detects the thumb drive user can see a brand or model name in DEVICE after pressing SCAN button A 11 01 Me ia 19 ES A 3 Select DVR name and version to be applied and then click OK to confirm It is not allowed to use the partitioned and or pass
47. ta then the system will keep video from August 11 to August 20 for 10days All other video recorded before August 11 will be deleted by the system On August 21 the system will keep video from August 12 to August 21 for 10days DUAL STREAM DVR can simultaneously generate two independent video streams one for local recording and the other for network transmission for user to effectively manage recording image quality and network traffic The frame rate and resolution for each stream can be independently set Dual stream function is applied to network transmission of the live image monitoring only In case of VOD Playback it is not related to dual stream and the network transmission follows record setting of the DVR 40 RESOLUTION Select the resolution to be transmitted It should be the smaller than or equal to the recording resolution The higher resolution requires the bigger network bandwidth due to its data size FPS Select the frame rate to be transmitted It is not related to the record setting QUALITY Select the image quality to be transmitted It is not related to the record setting The higher quality requires the bigger network bandwidth due to its data size AUDIO Select On or Off to transmit audio or not STREAM LIMIT lt allows user to reduce the image quality for transmission by percentage of the standard quality The lower percentage requires the smaller network bandwidth but the image quality will be worse O
48. ted through RS 232 port The POS data will be displayed on the assigned channel oT be e noel CAM TYPE PROTOCOL SAVE SHOW SETUP Assign ID for the port number of Serial Mux Ex ID1 COM1 ID4 COM4 Select the camera to link with POS device Communication type between DVR and POS device Communication protocol between DVR and POS device Select to save POS data Select to save POS data on the screen Click to go to the setup screen PLAYBACK DISPLAY SETTINGS Click to open setup screen for playback mode PORT SETUP Click to open setup screen for communication port Current POS setting ID Select the camera to link with POS device Communication type between DVR and POS device Input IP of POS device when it is connected through network 54 e PROTOCOL Communication protocol between DVR and POS device v TEXT IN Text input type ASCII character Y SDVR POS Manufacturer s own protocol e START CHARACTER Input the assigned character to start display and save If there is no input the system will display and save all data without classification per transaction eo END CHARACTER Input the assigned character to terminate display and save It must have START CHARCTER to work correctly LINE BREAK Set the line change character it should be 16 digits HEX Value v CRLF CR LF The character that is generally used in ASCII communication type POS Please
49. tem resources are occupied such as network connection or image playback during format process format may be failed In this case it is recommended to reboot the system to release system resources and then try to format again Note 1 The system always reserves some space in each built in HDD to effectively utilize archiving memory 2 When the format is done all data in the HDD will be deleted WARNING MESSAGE To achieve high level system stability warning message as below will be popped up when temperature inside the system exceeds optimum range This problem may be driven from mal function of ventilation fans In this case user shall inspect if the cooling fan is properly working or ambient temperature around the system is properly kept 30 3 1 5 Factory Default When the overall change of configuration is required or the system operation doesn t seem to be normal user can make the system to factory default The system setting will be originated by factory defaults However video data recorded are protected im P k r E al 31 3 2 Device 3 2 1 Camera User can set each camera s name motion area and covert function etc CAMERA lt shows camera channel number RESOLUTION It shows camera s resolution It is not related to the recording resolution TITLE In order to distinguish the channel from the others user can designate the channel name The name is applied to both DVR and remote monitoring softw
50. word encoded USB memory Do not take the USB memory stick from the port during upgrade It may cause serious damage to the DVR VIDEO SIGNAL It shows current setting video signal There are two modes of input signal 720P amp 720P 1080P Auto mode It can be selected by the switch on the rear side of the DVR Please set in consideration of the Cameras which are connected to the DVR IP ADDRESS It shows current setting value of IP address User can change it in Network setting menu 25 MAC ADDRESS It is the unique identity number for each system and cannot be changed KEY BOARD When the external keyboard controller is in use select the right protocol BAUDRATE Select Baudrate which is set at the keyboard controller User can select between 2400bps and 57600bps KEY PAD BEEP User can turn on or off the beeping sound of key pad of the front panel DISPLAY User can set sequence dwell time resolution OSG output alpha blending OSD display on the monitor as below picture gt ie az F TVN h ES f Es E x j Y des f r y A odeon SEQUENCE User can set dwell time for sequence display VGA RESOLUTION User needs to set the proper resolution in accordance with the monitor resolution Resolution is applied to both VGA amp Digital Output ALPHA BLENDING It is the transparency level of the menu screen 0 means no transparency at all OSD User can select the information that will be displayed on m
Download Pdf Manuals
Related Search