Home

Manual

1. Network Turret Camera Quick Operation Guide 1 Appearance Description Figure 1 1 Overview Table 1 1 Description 10M 100M self adaptive Ethernet interface Power Cable Network Turret Camera Quick Network Turret Camera Quick Operation Guide Guide o O beses ef o o o me o Please make sure that the power adapter is compatible with the camera This series of camera supports Power over Ethernet PoE and the standard power supply is 12 VDC Network Turret Camera Quick Operation Guide 2 Installation Before you start Make sure the device in the package is in good condition and all the assembly parts are included e Make sure all the related equipment is power off during the installation e Check the specification of the products for the installation environment Make sure the power supply is matched with your required voltage to avoid damage e f the product does not function properly please contact your dealer or the nearest service center Do not disassemble the camera for repair or maintenance by yourself Make sure that the wall is strong enough to withstand three times the weight of the camera E GE For the camera that supports IR you are required to pay attention to the following precautions to prevent IR reflection Dust or grease on the dome cover will cause IR reflection Please do not remove the dome cover film until the installation is finished If there is dust or g
2. Figure 2 4 Secure the Camera to the Ceiling 5 Adjust the Lens 1 Loosen the lock screw 2 Rotate the enclosure to adjust the pan angle rotate the camera to adjust the tilt angle 13 Network Turret Camera Quick Operation Guide 3 Tighten the lock screw to fix the optimum surveillance angle Lock Screw Figure 2 5 Lock Screw UY Figure 2 6 Adjust the Lens 14 Network Turret Camera Quick Operation Guide 6 Attach the trim ring to the camera and rotate the trim ring clockwise to get it secured AA Figure 2 7 Install the Trim Ring Figure 2 8 Complete the Installation 15 Network Turret Camera Quick Operation Guide 3 Setting the Network Camera over the LAN Purpose To view and configure the camera via LAN Local Area Network you need to connect the network camera in the same subnet with your PC Then install the SADP or PCNVR software to search and change the IP of network camera The following figure shows the cable connection of network camera and PC j aoe rr se tw serwof Switch k co g a Network Camera Computer Figure 3 1 Wiring over LAN Set the IP address of the camera for accessing via LAN Steps 1 To get the IP address you can choose either of the following methods A Use SADP a software tool which can automatically detect network camera in the LAN and list the device information like IP address subnet mask port number device se
3. Network Turret Camera Quick Operation Guide Network Turret Camera Quick Operation Guide Thank you for purchasing our product If there are any questions or requests please do not hesitate to contact the dealer About This Document This manual applies to the following models HNC301 XD HNC303 XD This manual may contain several technical incorrect places or printing errors and the content is subject to change without notice The updates will be added to the new version of this manual We will readily improve or update the products or procedures described in the manual DISCLAIMER STATEMENT Underwriters Laboratories Inc UL has not tested the performance or reliability of the security or signaling aspects of this product ULhas only tested for fire shock or casualty hazards as outlined in UL s Standard s for Safety UL60950 1 UL Certification does not cover the performance or reliability of the security or signaling aspects of this product UL MAKES NO REPRESENTATIONS WARRANTIES OR CERTIFICATIONS WHATSOEVER REGARDING THE PERFORMANCE OR RELIABILITY OF ANY SECURITY OR SIGNALING RELATED FUNCTIONS OF THIS PRODUCT 0501001031101 Network Turret Camera Quick Operation Guide Regulatory Information FCC Information FCC compliance This equipment has been tested and found to comply with the limits for a digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protec
4. 18 Network Turret Camera Quick Operation Guide You can click or on each column heading to order the information you can click to show the device table and hide the network parameter panel on the right side or click to show the network parameter panel O Modify device information Steps 1 Select the device to be modified in the device list as shown in Figure 3 3 The network parameters of the device will be displayed in the Modify Network Parameters panel on the right side as shown in Figure 3 4 Edit the modifiable network parameters e g IP address and port number Enter the password of the admin account of the device in the Password field and click Save to save the changes Total nunber of online devices 1 Refresh a ast a MEN arya iD Device Type IPv4 Address Port Software Version IiPv4 Gateway Serial No 001 DS XXXX XX 192 0 0 64 8000 VX X XbuildXXXX 192 0 0 1 XX XXXX XXXXXXXXXX Figure 3 3 Select a Device 19 Network Turret Camera Quick Operation Guide Modify Network Parameters IP Address 192 0 0 64 Port 3000 Subnet Mask 255 255 0 0 rast IPv4 Gateway 192 0 0 1 IPv6 Address IPv6 Gateway IPv6 Prefix Length Serial No XXXXXXXXXXXXXXXXXXXXX P assword Save v Note Enter the admin password of the device before you save the network parameters Figure 3 4 Modify Network Parameters 3 Enter the IP address of network camera in the address field
5. it to high electromagnetic radiation To avoid heat accumulation good ventilation is required for operating environment Keep the camera away from liquid while in use While in delivery the camera shall be packed in its original packing or packing of the same texture Regular part replacement a few parts e g electrolytic capacitor of the equipment shall be replaced regularly according to their average enduring time The average time varies because of differences between operating environment and using history so regular checking is recommended for all the users Please contact with your dealer for more details Improper use or replacement of the battery may result in hazard of explosion Replace with the same or equivalent type only Dispose of used batteries according to the instructions provided by the battery manufacturer If the product does not work properly please contact your dealer or the nearest service center Never attempt to disassemble the camera yourself We shall not assume any responsibility for problems caused by unauthorized repair or maintenance Network Turret Camera Quick Operation Guide Table of Contents 1 Appearance Description ccssccssssisicersescassossssecsscessieensessesencrssounvessss 8 2 Installati n 232 sneen Er re dre ange 10 3 Setting the Network Camera over the LAN ccsseccssecceseeeees 16 4 Accessing Via Web Browser sccsssssccssssecccssceccsssscccsseccceseesees 21
6. of the web browser to view the live video sm Nore The default value of the IP address is 192 0 0 64 The default user name is admin and password is 12345 For accessing the network camera from different subnets please set the gateway for the network camera after you log in 20 Network Turret Camera Quick Operation Guide 4 Accessing via Web Browser System Requirement Operating System Microsoft Windows XP SP1 and above version Vista Win7 Server 2003 Server 2008 32bits CPU Intel Pentium IV 3 0 GHz or higher RAM 1G or higher Display 1024x768 resolution or higher Web Browser Internet Explorer 6 0 and above version Apple Safari 5 02 and above version Mozilla Firefox 3 5 and above version and Google Chrome8 and above version Steps 1 Open the web browser 2 Inthe browser address bar input the IP address of the network camera e g 192 0 0 64 and press the Enter key to enter the login interface 3 Input the user name and password Click Login 21 Network Turret Camera Quick Operation Guide Erepish Uit Mane Sern Fisse HH Ligh Figure 4 1 Login Interface 5 Install the plug in before viewing the live video and managing the camera Please follow the installation prompts to install the plug in ia NOTE You may have to close the web browser to finish the installation of the plug in 22 Network Turret Camera Quick Operation Guide Live View Playba
7. 6 EC battery directive This product contains a battery that cannot be disposed of as unsorted municipal waste in the European Union See the product documentation for specific battery information The battery is marked with this symbol which may include lettering to indicate cadmium Cd lead Pb or mercury Hg For proper recycling return the battery to your supplier or to a designated collection point For more information see www recyclethis info Network Turret Camera Quick Operation Guide Safety Instruction These instructions are intended to ensure that user can use the product correctly to avoid danger or property loss The precaution measure is divided into Warnings and Cautions Warnings Serious injury or death may occur if any of the warnings are neglected Cautions Injury or equipment damage may occur if any of the cautions are neglected Warnings Follow these Cautions Follow these safeguards to prevent precautions to prevent serious injury or death potential injury or material damage A Warnings In the use of the product you must be in strict compliance with the electrical safety regulations of the nation and region Please refer to technical specifications for detailed information Input voltage should meet both the SELV Safety Extra Low Voltage and the Limited Power Source with 24 VAC or 12 VDC according to the IEC60950 1 standard Please refer to technical specifications for detai
8. ck Log Configuration Please click here to download and install the plug m Close the browser when installing the plug in Figure 4 2 Download Plug in Tanzel Figure 4 3 Install Plug in 1 23 Network Turret Camera Quick Operation Guide Setup Web Components lela a Setup has finished naling Web Component on your Coripauter Ole Finish ta awit Setup Figure 4 4 Install Plug in 2 6 Reopen the web browser after the installation of the plug in and repeat steps 2 4 to login xt For detailed instructions of further configuration please refer to the user manual of network camera 24
9. led information Network Turret Camera Quick Operation Guide Do not connect several devices to one power adapter as adapter overload may cause over heating or a fire hazard Please make sure that the plug is firmly connected to the power socket When the product is mounted on wall or ceiling the device shall be firmly fixed If smoke odor or noise rise from the device turn off the power at once and unplug the power cable and then please contact the service center A Cautions Make sure the power supply voltage is correct before using the camera Do not drop the camera or subject it to physical shock Do not touch sensor modules with fingers If cleaning is necessary use clean cloth with a bit of ethanol and wipe it gently If the camera will not be used for an extended period please replace the lens cap to protect the sensor from dirt Do not aim the camera at the sun or extra bright places Blooming or smearing may occur otherwise which is not a malfunction and affect the endurance of sensor at the same time The sensor may be burned out by a laser beam so when any laser equipment is in using make sure that the surface of sensor will not be exposed to the laser beam Network Turret Camera Quick Operation Guide Do not place the camera in extremely hot cold the operating temperature shall be 30 C 60 C or 40 C 60 C if the camera model has an H in its suffix dusty or damp locations and do not expose
10. rease on the dome cover clean the dome cover with clean soft cloth and isopropyl alcohol 10 Network Turret Camera Quick Operation Guide Make sure that there is no reflective surface too close to the camera lens The IR light from the camera may reflect back into the lens causing reflection The foam ring around the lens must be seated flush against the inner surface of the bubble to isolate the lens from the IR LEDS Fasten the dome cover to camera body so that the foam ring and the dome cover are attached seamlessly Steps 1 Rotate the trim ring counterclockwise to remove it from the camera Figure 2 1 Dissemble the Camera 11 Network Turret Camera Quick Operation Guide 2 Drill the screw holes and the cable hole on the ceiling according to the drill template Ceiling Mounting Figure 2 2 The Drill Template There are two cable outlet methods One is to route the cables through the cable hole and the other is to route the cables through the side outlet shown below Figure 2 3 Side Outlet 12 Network Turret Camera Quick Operation Guide ae NOTE Three side outlets on the enclosure are selectable which makes routing the cables easier instead of drilling a cable hole on the ceiling Use a plier to remove the plastic and route the cables through the hole 3 Connect the corresponding power network cable 4 Fix the camera to the ceiling with the supplied expansion YW Screws
11. rial number device version etc shown in O 16 Network Turret Camera Quick Operation Guide O Use PCNVR software and to list the online devices Please refer to the user manual of PCNVR client software for detailed information 2 Change the IP address and subnet mask to the same subnet as of your PC Refer to the following introductions to set IP address with SADP software O Search active devices online Search online devices automatically After launch the SADP software it automatically searches the online devices every 15 seconds from the subnet where your computer locates It displays the total number and information of the searched devices in the Online Devices interface Device information including the device type IP address port number gateway etc will be displayed 17 Network Turret Camera Quick Operation Guide PRm gt Sohns Meroe Pa len Senai feo KENDON 992 001 151000 00000000 Note Erte Be saren pas sort ol Me sewe Detre you save Pe networt parameters Now Serta coe is penes of mancen U DANA tv Pe st t bre and Pe pers Figure 3 2 Search Online Devices NOTE Device can be searched and displayed in the list in 15 seconds after it goes online it will be removed from the list in 45 seconds after it goes offline Search online devices manually Refresh You can also click sal to refresh the online device list manually The newly searched devices will be added to the list
12. tion against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense FCC Conditions This device complies with part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference 2 This device must accept any interference received including interference that may cause undesired operation EU Conformity Statement This product and if applicable the supplied 3 accessories too are marked with CE and comply therefore with the applicable harmonized European standards listed under the Low Voltage Directive 2006 95 EC the EMC Directive 2004 108 EC the RoHS Directive 2011 65 EU Network Turret Camera Quick Operation Guide 2012 19 EU WEEE directive Products marked with this symbol cannot be disposed of as unsorted municipal waste in the European Union For proper recycling return this product to your local supplier aa upon the purchase of equivalent new equipment or dispose of it at designated collection points For more information see www recyclethis info 2006 6

Manual

Contents

Download Pdf Manuals

Related Search

Related Contents