DIY LED Tape Kit manual_191213 - Choose-AV
Contents
1. NY fluxia NY fluxia DIY LED Tape Kit Yfluxia Use a soldering iron and solder to connect the DC wire to the relative terminals be sure not to cause a short circuit when making these connections DIY LE D TAPE KIT as this will result in malfunction and possible damage to the power supply FIG 2 co o asso BORO o osko a ae Required distance User Manual DIY LED TAPE KIT SINGLE COLOUR Introduction ane WARNING Only cut the tape on the highlighted intervals Cutting the tape in other parts without due care will permanently damage that section oe of the tape and will result in malfunction Thank you for purchasing the Fluxia DIY LED Tape Kit LED tape is ideal for use on the underside of a counter tops shelves cupboards around window frames or in an alcove of a ceiling to name just a few examples Points to remember when using this tape Before starting please ensure that you have read this instruction leaflet carefully 1 Only use the supplied power supply for 5m If you are unsure about anything please have this installed by a competent installer 2 Only cut the tape at the highlighted 5cm intervals 3 Do not connect another reel and operate from a single power supply as this will seriously affect the performance Blister Contents 3 The top track of the tape is the Positive pole 4 The bottom track of the tape is the negative pole 1 x 5m reel of LED tape 5 Ensure you connect the correct wires2. e tape together to form a loop it can be easily reconnected and used again see FIG 2 A Yes you can This will even the brightness out on the LEDS across the 5m length Step 3 Fitting Q Can I use the tape outdoors A Yes the tape is IP65 rated Ensure that the terminated ends are heat shrink protected Example 1 Simple straight run Q Can I clean the tape Clear the area you wish to install the tape and remove the backing paper exposing the adhesive tape Push tape firmly onto the surface It is A Yes the tape is IP65 rated and has an epoxy coating Just wipe down with a damp cloth regularly to ensure continuing brightness recommended to work on 50cm sections at a time in order to ensure a professional finish When you reach the end of your installation cut at the marked cutting point Q Can I replace patch damaged tape with a new piece A Yes just highlight the effected area by the 5cm intervals Cut out the faulty section then fit in a new piece soldering the connections securely Example 2 Requires cutting and using heat shrink to protect the repaired connection The tape can be cut at highlighted 5cm intervals for a perfect fit Specifications FIG 1 Voltage 12Vdc Cutting point Cutting point Cutting point Current consumption 480mA m Power consumption 5 76W m Number of LEDs 60 m LED Spacing 16mm Cut intervals 5cm Beam angle 140 160 LED type SMD3528 IP rating IP65 You may a
3. lso reconnect the two pieces by soldering the connection points together FIG 2 The tape has two tracks for the DC voltage with positive pole at the top and negative pole at the bottom To reattach use a craft knife to cut the Epoxy coating from the terminals DIY LED Tape Kit User Manual DIY LED Tape Kit User Manual LED DIY TAPE KIT RGB MULTI COLOUR Introduction NY fluxia Thank you for purchasing the Fluxia DIY RGB LED Tape LED tape is ideal for use on the underside of a counter tops shelves cupboards around window frames or in an alcove of a ceiling to name just a few examples Before starting please ensure that you have read this instruction leaflet carefully If you are unsure about anything please have the tape installed by a competent installer Contents 1 x 5m reel of RGB LED tape 1 x Power supply with 3 region adaptors UK EU amp Worldwide 1 x Control Box with IR remote handset Possible required tools Scissors Craft knife Soldering iron and solder 4 core DC wire and heat shrink tube Step 1 Preparation Ensure the surface you are attaching to is clear of dust and dirt Clean thoroughly and leave to dry before fitting the tape Step 2 Connecting IR Controller Connect the 4pin connector to the control box and then to the LED tape FIG 1 Plug in the power supply and use the IR remote control to select the various functions Fig 2 Unravel the tape to check that all the LEDs are f
4. otherwise the tape will not work 1 x Power supply with 3 region adaptors UK EU amp Worldwide 6 Ensure that when soldering there are no short circuits 7 We recommend use of heat shrink tubing to protect the connection Possible Required tools Scissors Craft knife Soldering iron and solder 2 core DC wire and heat shrink tube 8 Check that everything operates correctly before installing Step 1 Preparation FAQ Ensure that the surface you are attaching to is clear of dust and dirt Clean thoroughly and leave to dry before fitting the tape Q Can I connect different colours in a chain Unravel the tape and connect the power supply Check that all the LEDs are functioning correctly and if there are any faults return to your retailer AE al EEDS Araw thg Same Bower current and have tng Same connection Dut Oo nob ey seed Sm without delay Q Can you cut a 5m tape into many different sections then connect them all together Step 2 Cutting A Yes as long as you cut the tape at 5cm intervals highlighted Q I have connected two reels together off one power supply and the LEDs are dim towards the end WARNING Disconnect from the power supply before attempting any cutting A This product is designed to be used at a maximum of 5m Anything longer will seriously affect the performance Measure out each section and cut with sharp scissors at the marked 5cm intervals to achieve the perfect length Do not discard any excess tape as Q Can I connect th
5. r the DC voltage Common indicated as 12V on the tape Green Red and Blue To re attached use a craft knife to cut the Epoxy coating from the terminals Use a soldering iron and solder to connect the DC wire to the relative terminals be sure not to cause a short circuit in the process as it will not work FIG4 Cutting point Cutting point O38 O EE Q 0 0 ie O Q 0 0 0 Q 4n nn Required distance Cutting point cut it Cutting point 000 C000 O O T o O WARNING Only cut the tape on the highlighted intervals Cutting the tape in other parts without due care will permanently damage that section of the tape and will result in malfunction Points to remember when using this tape 1 Only cut the tape at the highlighted 10cm intervals 2 Do not connect another reel and operate from a single power supply as this will seriously affect the performance 3 Ensure you connect the correct wires otherwise the tape will not work 4 Ensure that when soldering there are no short circuits 5 We recommend use of heat shrink tubing to protect the connection 6 Check that everything operates correctly before installing FAQ Q Can you cut a 5m tape in many of different sections then solder connect them all together A Yes as long as you cut the tape at 10cm intervals highlighted Q Can I connect the tape together to form a loop A Yes you can as long as both sides have a
6. sufficient power supply it is possible Q Can I use the tape outdoors A Yes the tape is IP65 rated Ensure though that the terminated ends are heat shrink protected Q Can I use the LED tape without a controller A Yes you can but you can only have a choice of 7 permanent colours It will be a better solution to buy the single colour tape Specifications Voltage 12Vdc Current consumption 600mA m Power consumption 7 2W m Number of LEDs 30 m LED Spacing 32mm Cut intervals 10m Beam angle 140 160 LED type SMD5050 IP rating IP65 Errors and omissions excepted Copyright 2013 AVSL Group Ltd DIY LED Tape Kit User Manual
7. unctioning correctly If there are any faults return to your retailer without delay FIG 1 Control Box Power IN IR Receiver Connector ATT FIG 2 Brightness Brightness Rise Drop OF al Static i Static Static Red Grean Static Blue White Static 7 Colour Static K Static A Orange Pci Deep Blue changing reen program Static Deep Yellow Static Cyan Static Brown Gradually changing Static Yellow Step 2 Cutting Static Light Blue Static Sky Blue Static Pink WARNING Disconnect from the power supply before attempting any cutting 7 Colour fade changing 3 Colour quick changing LED Tape O OG C Measure out each section and cut with sharp scissors only at the marked 10cm intervals Do not discard any excess tape as it can be easily reconnected and used again see FIG 4 DIY LED Tape Kit User Manual Step 4 Fitting NV fluxia Clear the area you wish to install and remove the backing paper exposing the adhesive tape Push tape firmly onto the surface It is recommended to work on 50cm sections at a time in order to ensure a professional finish When you reach the end of your installation cut at the marked cutting point The tape can be terminated at highlighted 10cm cut intervals if less than 5m is required FIG 3 Cutting point You may also reconnect the two pieces by soldering the point connections together The tape has 4 tracks fo
Download Pdf Manuals
Related Search