802.11bg High-Power Outdoor AP/CPE USER MANUAL
Contents
1. DH2 modp1024 or DH5 modpl536 key ee ee ae Description Key Life Time Fill in the key life time value by seconds Phase 2 Encryption Click to select 3DES AES128 or NULL Algorithm encryption Authentication Click to select MDS or SHAT authentication Algorithm 7 Be Key Life Time Fill in the key life time value by seconds Perfect Forward Click to select ON or NONE secrecy PFS Ok Click the Ok button to save current tunnel settings eee Cancel Click the Cancel button to close current window without any changes 2 3 19 Management Statistics This page shows the packet counters for transmission and reception regarding to wireless Ethernet LAN and Ethernet WAN networks Statistics This page shows the packet counters for transmission and reception regarding to wireless and Ethernet networks a d ent Packets Wireless LAN Received Packets Sent Packets Ethernet LAN Received Packets ee Sent Packets Ethernet WAN Received Packets Screen snapshot Management Statistics Item Description Wireless LAN It shows the statistic count of sent packets on Sent Packets the wireless LAN interface Wireless LAN It shows the statistic count of received packets Received Packets on the wireless LAN interface Ethernet LAN It shows the statistic count of sent packets on Sent Packets the Ethernet LAN interface Ethernet LAN It shows the statistic count of received packets Received Packets2. Enable uPNP Enable Web Server Access on WAN Enable WAN Echo Set TTL value Click the checkbox to enable uPNP function _ Click the checkbox to enable WAN ICMP response Apply Changes Click the Apply Changes button to complete the new configuration setting Reset Click the Reset button to abort change and recover the previous configuration setting vansanansononsenennnsnnensnsnnensnnensnsnnensnsnensnnenensnsenensenensnsenensnnenensnnenrnnenensenennnnnnensennenrenensnenennsnnenensnnenensnnensnsnnensnnenensnnensnsnnensnsensnsnsenensnnensnsnnensnnnnnnsennnensnnenrennnensensnsnsensnsnrn PPTP This page is used to configure the parameters for Intemet network which connects to the WAN port of your Access Point Here you may change the access method to static IP DHCP PPPoE or PPTP by click the item value of WAN Access type WAN Access Type PPTP IP Address 172 1 1 2 Subnet Mask 255 255 255 0 Server IP Address V1 1 User Name Password MTU Size 1400 1400 1460 bytes Request MPPE Encryption Attain DNS Automatically Set DNS Manually DNS 1 168 95 1 1 DNS 2 192 168 0 5 DNS 3 0 0 0 0 Clone MAC Address 000000000000 Enable uPNP Enable Ping Access on WAN Enable Web Server Access on WAN Enable IPsec pass through on VPN connection Enable PPTP pass through on VPN connection Enable L2TP pass through on
3. 802 1 lbg High Power Outdoor AP CPE USER MANUAL 1 Installation 1 1 Hardware Installation diagram Pa 1 Plug Power adapter into APoE02 WM RJ45 2 Connect RJ45 LAN Port to cable computer or Switch r Data 3 Connect RJ45 PoE Port to CPE RJ45 cable 1 2 Mounting kit Installation Diagram m 2 Software configuration There are web based management and configuration functions allowing you to have the jobs done easily The AP is delivered with the following factory default parameters on the Ethernet LAN interfaces Default IP Address 192 168 1 250 Default IP subnet mask 255 255 255 0 WEB login User Name admin WEB login Password 12345 2 1 Prepare your PC to configure the AP For OS of Microsoft Windows 95 98 Me l Click the Start button and select Settings then click Control Panel The Control Panel window will appear Note Windows Me users may not see the Network control panel If so select View all Control Panel options on the left side of the window Move mouse and double click the right button on Network icon The Network window will appear Check the installed list of Network Components If TCP IP is not installed click the Add button to install it otherwise go to step 6 Select Protocol in the Network Component Type dialog box and click Add button Select TCP IP in Microsoft of Select Network Protocol dialog box then click OK button to in
4. VPN Setup Edit 1 Item Enable Tunnel Local IP Address Network Local Subnet Mask Description Click to enable the IPSEC VPN current tunnel Connection Name Click to select PSK or RSA Click to select Single Address or Subnet Address VPN connection Fill in IP address or subnet address depends on which Local Site option you choose Fill in the local subnet mask Click to select Single Address Subnet Address Any Address or NAT T Any Address Remote Secure VPN remote connection Gateway Fill in remote gateway IP address Remote IP Address Network Fill in IP address or subnet address depends Remote Subnet Mask on which Remote Site option you choose Fill in remote subnet mask Local PeerID Define IKE exchange information type Local ID Type Click to select IP DNS or E mail as local Local ID exchange type Remote ID Type Fill in local ID except IP selected Click to select JP DNS or E mail as remote Remote ID exchange type Fill in remote ID except IP selected 1EE Manual Encryption Algorithm Authentication Algorithm 1234567 Status Connected Screen snapshot VPN Setup Edit 2 Item Description Key Management Click to select IKE or Manual mode Advanced Click Advanced button to configure more IKE Be settings Connection Type Click to select Initiator or Responder mode Connect Click to connect manually Responder mode _ only Disconnect Click
5. While Encryption is selected to be WPA Select the Pre shared key format from the pull down menu The format can be Passphrase or Hex 64 characters WPA Click to enable Pre Authentication WPA2 WPA2 Mixed only Enterprise only Set the IP address port and login password information of authentication RADIUS sever Click the Apply Changes button to complete the new configuration setting Click the Reset button to abort change and En recover the previous configuration setting WEP Key Setup Wireless WEP Key Setup This page allows you setup the WEP key value You could choose use O4 bit or 128 bit as the encryption key and select ASCI or Hex as the format of Input value Key Leagh Eer Format Hex 10 characters w Default Tx Ker Baron Key 1 Basten Key 2 Basten Key 3 Basten Key 4 ETEN Sid Beal Screen snapshot WEP Key Setup Item Descriptio Key Length Select the WEP shared secret key length from pull down menu The length can be chose between 64 bit and 128 bit known as WEP2 keys The WEP key is composed of initialization vector 24 bits and secret key 40 bit or Key Format Select the WEP shared secret key format from pull down menu The format can be chose between plant text ASCII and hexadecimal Default Tx Key Set the default secret key for WEP security function Encryption Key 1 Secret key 1 of WEP security encryption A e Encryption Key 2 Secret key 2 of WE
6. URL address that Delete All Click to delete all the registered entries from the URL Filtering list Reset Click the Reset button to abort change and recover the previous configuration setting 2 3 17 Firewall DMZ A Demilitarized Zone is used to provide Internet services without sacrificing unauthorized access to its local private network Typically the DMZ host contains devices accessible to Internet traffic such as Web HTTP servers FTP servers SMTP e mail servers and DNS servers DMZ A Demilitarized Zone is used to provide Internet services without sacrificing unauthorized access to its local private network Typically the DMZ host contains devices accessible to Internet traffic such as Web HTTP servers FIP servers SMTP e mail servers and DNS servers Enable DMZ DMZ Host IP Address 192 766 1201 Screen snapshot Firewall DMZ Item Description VUT UE UEC ENEHOECEEOEOEEOEOESEEOEOESUSOEOESOROESOAUEOESERUESESOSUEEESOSSEROESENOROESERURUESEAUESESERURUERURUESEROROENEEOEOEEOESESOEOESESUEOESERUEOESORUESESOEUESEROSUENOSUSNOROESENOHOESESUESESEAUESEOERURSERURUESEROEEEEOEOESEEOEOEEOEOESEEOEOEREROm DMZ Host IP To support DMZ in your firewall design fill in Address the IP address of DMZ host that can be access from the WAN interface Apply Changes Click the Apply Changes button to register the OO 8 as Reset Click the Reset button to abort change and Be ce SNE 2 3 18 VPN Setting This page is u
7. static IP DHCP PPPoE or PPTP by click the item value of WAN Access type WAN Access Type SacP M IP Address 172 1 1 1 Subnet Mask 255 255 255 0 Default Gateway 172 1 1 254 MTU Size 1400 1400 1500 bytes DNS 1 168 9511 i DNS 2 192 168 0 5 DNS 3 0 0 0 0 Clone MAC Address 000000000000 Enable uPNP C Enable Ping Access on WAN C Enable Web Server Access on WAN Enable IPsec pass through on VPN connection Enable PPTP pass through on VPN connection Enable L2TP pass through on VPN connection C Set TIL Value 6 499 Screen snapshot WAN Interface Setup Static IP Item Description Static IP Click to select Static IP support on WAN interface There are IP address subnet mask and default gateway settings need to be done IP Address If you select the Static IP support on WAN interface fill in the IP address for it Subnet Mask If you select the Static IP support on WAN interface fill in the subnet mask for it Default Gateway If you select the Static IP support on WAN interface fill in the default gateway for WAN interface out going data packets MTU Size Fill in the mtu size of MTU Size The default Oo value is 1400 DNS 1 Full in the IP address of Domain Name Server l DNS 2 a Fill in the IP address of Domain Name Server o pA DNS 3 Fill in the IP address of Domain Name Server 3 Clone MAC Address Fill in the MAC address
8. that is the MAC address to be cloned Enable uPNP Click the checkbox to enable uPNP function Enable Web Server Click the checkbox to enable web configuration Access on WAN from WAN side Enable WAN Echo Click the checkbox to enable WAN ICMP Reply response Enable IPsec pass Click the checkbox to enable IPSec packet pass through on VPN through connection Enable PPTP pass Click the checkbox to enable PPTP packet pass through on VPN through Enable L2TP pass Chick the checkbox to enable L2TP packet pass through on VPN through connection Set TTL value Click to Enable and set Time to Live value Apply Changes Click the Apply Changes button to complete the new configuration setting Reset Click the Reset button to abort change and recover the previous configuration setting DHCP Client WAN Interface Setup This page is used to configure the parameters for Intemet network which connects to the WAN port of your Access Point Here you may change the access method to static IP DHCP PPPoE or PPTP by click the itera value of WAN Access type WAN Access Type Host Name MTU Size 1 400 1400 1492 bytes Attain DNS Automatically Set DNS Manually DNS 1 DNS 2 DNS 3 Clone MAC Address 000000000000 C Enable uPNP C Enable Ping Access on WAN C Enable Web Server Access on WAN Enable IPsec pass through on VPN connection Enable P
9. the current configuration to factory default Save Reload Settings This page allows you save current settings to a file or reload the settings from the file which was saved previously Besides you could reset the current configuration to factory default Save Settings to File Load Settings from File fe Upload Reset Settings to Default Screen snapshot Management Save Reload Settings Item Description Save Settings to File Click the Save button to download the configuration parameters to your personal computer Load Settings from Click the Browse button to select the File configuration files then click the Upload button to update the selected configuration to the AP Reset Settings to Click the Reset button to reset the configuration Default parameter to factory defaults 2 3 26 Management Password Setup This page is used to set the account to access the web server of Access Point Empty user name and password will disable the protection Password Setup This page is used to set the account to access the web server of Access Point Empty user name and password will disable the protection User Name New Password Confirmed Password fs Apply Changes Screen snapshot Management Password Setup Item Description User Name Fill in the user name for web management login control New Password Fill in the password for web management login BS control Confirmed Password Bec
10. 00 02 72 81 86 0a AP 1 00 02 72 81 86 0b AP 2 Delete Selected Delete All Screen snapshot WDS Setup Item Description Enable WDS Click the check box to enable wireless distribution system MAC Address Fill in the MAC address of AP to register the wireless distribution system access capability Comment Fill in the comment tag for the registered AP Apply Changes Click the Apply Changes button to register the AP to new configuration setting Reset Click the Reset button to abort change and Se eS eee Set Security Click button to configure wireless security like WEP 64bits WEP 128bits WPA TKIP WPA2 AES or None Show Statistics It shows the TX RX packets rate statistics Delete Selected Click to delete the selected clients that will be removed trom the wireless distribution system Delete All Click to delete all the registered APs from the wireless distribution system allowed list Reset Click the Reset button to abort change and recover the previous configuration setting WDS Security Setup Requirement Set Wireless gt Basic Settings gt Mode gt AP WDS This page is used to configure the wireless security between APs WDS Security Setup This page allows you setup the wireless security for WDS When enabled you must make sure each WDS device has adopted the same encryption algorithm and Key Encryption WEP Key Format WEP Kev Pre Shared Key Format Pre Shared
11. AP Open a WEB browser 1 e Microsoft Internet Explore then enter 192 168 1 254 on the URL to connect the AP 2 3 Management and configuration on the AP 2 3 1 Status This page shows the current status and some basic settings of the device includes system wireless Ethernet LAN and WAN configuration information Broadband Router Status This page shows the current status and some basic settings of the device Ystem Uptime Oday Oh 2313s Firmware Version wad Wireless Configuration AP 2 4 GHz BH MW LAN 11 Disabled Oe ED 86 g Fined IP 192 168 1244 255 255 2550 1821681254 Enabled Oe 1 A 81 06 1821580146 255 255 255 0 132 163 010 168 95 1 1 132 168 0 5 0 0 0 0 Oe F214 a1 8 Screen snapshot Status Item Descript Wireless configuration Mode It shows wireless operation mode Band It shows the current wireless operating frequency SSID It shows the SSID of this AP The SSID is the unique name of AP and shared among its service area so all devices attempts to join the same wireless network can identify it Channel Number It shows the wireless channel connected currently Encryption It shows the status of encryption function BSSID It shows the BSSID address of the AP BSSID 1s a six byte address Associated Clients It shows the number of connected clients or stations PCs IP Address It shows the IP address of LAN interfaces of Subnet Mask It show
12. Click the Apply Changes button to complete Reset Click the Reset button to abort change and recover the previous configuration setting 2 3 6 Wireless Security Setup This page allows you setup the wireless security Turn on WEP WPA WPA2 by using encryption keys could prevent any unauthorized access to your wireless network Wireless Security Setup This page allows you setup the wireless security Tum on WEP or WPA by using Encryption Keys could prevent any unauthorized access to your wireless network Encryption _ Use 02 1x Authentication WEP tbits WEP 12 8bits WPA Authentication Mode Enterprise RADIUS Personal Pre Shared Key Pre Shared Key Format Enable Pre Authentication Note When encryption WEP is selected vou must set WEP key value Apply Changes Screen snapshot Wireless Security Setup WE o Encryption Use 802 1x Authentication WPA Authentication Mode Pre Shared Key Format Pre Shared Key Enable Pre Authentication Authentication RADIUS Server Apply Changes Reset _ Description Select the encryption supported over wireless access The encryption method can be None WEP WPA TKIP WPA2 or WPA2 Mixed While Encryption is selected to be WEP Click the check box to enable IEEE 802 1x authentication function While Encryption is selected to be WPA Click to select the WPA Authentication Mode with Enterprise RADIUS or Personal Pre Shared Key
13. Kev Screen snapshot WDS Security Setup WDS AP Table This page is used to show WDS statistics WDS AP Table This table shows the MAC address transmission recerption packet counters and state information for each configured WDS AP Screen snapshot WDS AP Table Item Description SAUENERSESEAEEOESESEESESEAUESESEESESESUEOESESUEOESESUESESURURSEROESESEEOESESEESESUSUESESUSUESESUSUESESUESESOSUESESOSUENESUSUESESUSUSHOSOSUSHOSUSESSORSESESOESESUESESESUESESEEUESESESUESESEAUESESUSUESOSURSESORSESESOESESEESESESOESESESUESESEROES ES MAC Address It shows the MAC Address within WDS Tx Packets It shows the statistic count of sent packets on the wireless LAN interface Tx Errors It shows the statistic count of error sent packets on the Wireless LAN interface Rx Packets It shows the statistic count of received packets on the wireless LAN interface Tx Rare Mbps It shows the wireless link rate within WDS SAUENERSESEAERSESESEESENEROESESEROESEAUEEUESERUEUESESUREESORORSERORSESEEOESESERSESESUESESESUESESESUESESUEOESOSUESESOSUESESOSUSSESOSUSEOSOSUSSOSUSUSHORSESESOESESERSESESEESESERESESERUESESERUESESUSUESOESESESOESESESOESESEROESESEEOESESOESESESOEOESM Refresh Click to refresh the statistic counters on the screen Close Click to close the current window 2 3 9 Site Survey This page is used to view or configure other APs near yours Wireless Site Survey This page provides tool to scan the wireless network F an
14. P security encryption function Encryption Key 3 Secret key 3 of WEP security encryption function Encryption Key 4 Secret key 4 of WEP security encryption LE Apply Changes Click the Apply Changes button to complete the new configuration setting Close Click to close this WEP Key setup window Reset Click the Reset button to abort change and recover the previous configuration setting WEP encryption key secret key ae Forma t 64 bit 2 128 bit ASCI Sc characters o 13 characters 2a ee eee HEX 10 hexadecimal codes 26 hexadecimal codes 2 3 7 Wireless Access Control If you enable wireless access control only those clients whose wireless MAC addresses are in the access control list will be able to connect to your Access Point When this option is enabled no wireless clients will be able to connect if the list contains no entries Wireless Access Control Ifyou choose Allowed Listed only those chents whose wireless MAC addresses are in the access control list will be able to connect to your Access Point When Deny Listed is selected these wireless chents on the list will not be able to connect the Access Point Wireless Access Control Mode Allow Listed MAC Address Comments Current Access Control List 00 02 72 81 86 01 00 00 55 66 66 50 Delete Selected Delete All Screen snapshot Wireless Access Control Item Description Wireless Access Click the Disa
15. PTP pass through on VPN connection Enable L2TP pass through on VPN connection C Set TTL Value Ca 1 128 Screen snapshot WAN Interface Setup DHCP Client _ Description Attain DNS Automatically Set DNS Manually Click to select DHCP support on WAN interface for IP address assigned automatically from a DHCP server Fill in the host name of Host Name The default value is empty Fill in the mtu size of MTU Size The default value is 1400 Click to select getting DNS address for DHCP support Please select Set DNS Manually if nm the DHCP support is selected Click to select getting DNS address for DHCP support Fill in the IP address of Domain Name Server A Fill in the IP address of Domain Name Server 2 _ Fill in the IP address of Domain Name Server gt address to be cloned wenenevernensvernenenarnensnnenensenrnensenenenmenenenvenenennenenennenenennenenenvenenennenenenvenenennensnnre Enable uPNP Click the checkbox to enable uPNP function Enable Web Server Click the checkbox to enable web Access on WAN configuration from WAN side Enable WAN Echo _ Click the checkbox to enable WAN ICMP Reply response Set TTL value Click to Enable and set Time to Live value Apply Changes Click the Apply Changes button to complete ee the new configuration setting Reset Click the Reset button to abort change and recover the previous configuration setting This page is used to co
16. Port Range network behind the NAT firewall fill in the IP Comment address protocol port range and your comments The Protocol can be TCP UDP or Both The Port Range for data transmission Comments let you know about whys to allow number Apply Changes Click the Apply Changes button to register the IP address and port number to Port forwarding list Reset Click the Reset button to abort change and recover the previous configuration setting Delete Selected Click to delete the selected IP address and port number that will be removed from the port forwarding list Delete All Click to delete all the registered entries from the port forwarding list Reset Click the Reset button to abort change and recover the previous configuration setting 2 3 16 Firewall URL Filtering URL Filtering is used to restrict users to access specific websites in internet URL Filtering URL filter is used to deny LAN users from accessmg the internet Block those URLs which contain keywords listed below Enable URL Filtering URL Address wilfilter lst com Current Filter Table see cl filter bat com Screen snapshot Firewall URL Filtering Item Description Enable URL Click to enable the URL Filtering function Filtering URL Address Add one URL address Apply Changes Click the Apply Changes button to save Reset Click the Reset button to abort change and Delete Selected Click to delete the selected
17. VPN connection Set TTL Value 1 18 HAHN OOd oO Screen snapshot WAN Interface Setup PPTP Item Description PPTP Allow user to make a tunnel with remote site directly to secure the data transmission among the connection User can use embedded PPTP client supported by this router to make a VPN nn IP Address If you select the PPTP support on WAN EE CSE Subnet Mask If you select the PPTP support on WAN interface fill in the subnet mask for it User Name If you select the PPTP support on WAN interface fill in the user name and password to f you select the PPTP support on WAN interface fill in the user name and password to Password MTU Size Fill in the mtu size of MTU Size The default value is 1400 OO Request MPPE Click the checkbox to enable request MPPE Encryption encryption OO Attain DNS Click to select getting DNS address for PPTP Automatically support Please select Set DNS Manually if Set DNS Manually Click to select getting DNS address for PPTP ME A T DNS 1 Fill in the IP address of Domain Name Server DNS 2 Fill in the IP address of Domain Name Server DNS 3 Fill in the IP address of Domain Name Server Clone MAC Address Fill in the MAC address that 1s the MAC Enable uPNP Click the checkbox to enable uPNP function Access on WAN configuration from WAN side Enable WAN Echo Click the checkbox to enable WAN ICMP A ee Apply Changes Click the Apply Changes button t
18. ause the password input 1s invisible so please fill in the password again for ee confirmation purpose Apply Changes Clear the User Name and Password fields to empty means to apply no web management login control Click the Apply Changes button to complete the new configuration setting Reset Click the Reset button to abort change and recover the previous configuration setting 2 3 27 Logout This page is used to logout web management page This item will be activated next time you login after you define user account and password Logout This page 18 used to logout Do you want to logout Screen snapshot Logout Change setting successfully Screen snapshot Logout OK Apply Change Click the Apply Change button Then click OK button to logout
19. bled IAPP Enabled Disabled 802 112 Protection Enabled Disabled RF Output Power DIE Owy O25 ODB O5 Turbo Mode O auto Awy Of Note Always may have compatibility issue Avto will only werk with Realtek product Block Relay Between Clients Enhed Disabled WMH O Enabled Disabled ACK Timeout O 0255 lt Cument 116 3160s 11g Pons gt Screen snapshot Wireless Advanced Settings Authentication Type Click to select the authentication type in Open En A K Fragment Threshold Set the data packet fragmentation threshold value can be written between 256 and 2346 bytes RTS Threshold Set the RTS Threshold value can be written between Q and 2347 bytes lt lt o Beacon Interval Set the Beacon Interval value can be written Data Rate Select the transmission data rate from pull down menu Data rate can be auto select _______1IM 5 5M 2MorlMbps Preamble Type Click to select the Long Preamble or Short Preamble support on the wireless data packet transmission Broadcast SSID Click to enable or disable the SSID broadcast function 802 11g Protection Protect 802 11b user RF Output Power To adjust transmission power level Turbo Mode Click to Enable Disable turbo mode Only i EO Block Relay Click Enabled Disabled to decide if blocking A EE ED OA EN hade Le eee a ACK Timeout Set ACK timeout value It shows current time in the end Apply Changes
20. bled Allow Listed or Deny Control Mode Listed of drop down menu choose wireless access control mode This is a security control function only those clients registered in the access control list can MAC Address Fill in the MAC address of client to register this Comment _ Fill in the comment tag for the registered client Apply Changes Click the Apply Changes button to register the _ client to new configuration setting _ ee pen space recover the previous configuration setting Current Access It shows the registered clients that are allowed _ Control List to link to this AP Delete Selected Click to delete the selected clients that will be _ Delete Al Click to delete all the registered clients from EO nn Reset Click the Reset button to abort change and EC OVET Ne DiC MOUS CONE AO EE __ 2 3 8 WDS Settings Wireless Distribution System uses wireless media to communicate with other APs like the Ethernet does To do this you must set these APs in the same channel and set MAC address of other AP that you want to communicate with in the table and then enable the WDS WDS Settings Wireless Distribution System uses wireless media to communicate with other APs like the Ethernet does To do this you must set these APs in the same channel and set MAC address of other APs which you want to communicate with in the table and then enable the WDS Enable WDS Add WDS AP MAC Address E i Comment OoOo Current WDS AF List
21. brl topology change detected propagating Oday OO 02 18 brl port lieth entering learning State Oday 00 02 14 bri port lieth entering forwarding state Oday 00 02 18 brl topology change detected propagating Ze Screen snapshot Management Log Enable Log Click the checkbox to enable log System all Show all log of wireless broadband router Wirelessy Only show wireless log OO eee Enable Remote Log Click the checkbox to enable remote log Log Server IP Service dd EO eee Apply Changes Click the Apply Changes button to save above Refresh Click the refresh the log shown on the screen Clear Clear log display screen 2 3 24 Management Upgrade Firmware This page allows you upgrade the Access Point firmware to new version Please note do not power off the device during the upload because it may crash the system Upgrade Firmware This page allows you upgrade the Access Point firmware to new version Please note do not power off the device during the upload because it may crash the system Screen snapshot Management Upgrade Firmware Item Descriptio Select File Click the Browse button to select the new Upload Click the Upload button to update the selected Reset Click the Reset button to abort change and KE RAE LON 2 3 25 Management Save Reload Settings This page allows you save current settings to a file or reload the settings from the file that was saved previously Besides you could reset
22. ct on Demand and Manual three types to select Continuous connection type means to setup the connection through PPPoE protocol Idle Time MTU Size Attain DNS Automatically Set DNS Manually DDO DNS 1 DNS2 0 DNS3 whenever this AP is powered on Connect on Demand connection type means to setup the connection through PPPoE protocol whenever you send the data packets out through the WAN interface there are a watchdog implemented to close the PPPoE connection while there are no data sent out longer than the idle time set Manual connection type means to setup the connection through the PPPoE protocol by clicking the Connect button manually and If you select the PPPoE and Connect on Demand connection type fill in the idle time for auto disconnect function Value can be Fill in the mtu size of MTU Size The default _ value is 1400 SNSEESESESESESESESESUESESESOESESESUESESESSESESUSSESOSOSSESESSESESOSSESESSESESEESESESEESESESUSSESESSSSESESUESESUSSSSESSSSSSOSUSESSOESESSESESESSESESESESSESESSESESEEOESESESSESESESSESESUESESESUSSESSSESESEESESEEDSSESEOESEEEEOESESOEOESEEOES n Click to select getting DNS address for PPPoE support Please select Set DNS Manually if the Click to select getting DNS address for Static Fill in the IP address of Domain Name Server _ Fill in the IP address of Domain Name Server Fill in the IP address of Domain Name Server 3 Clone MAC Address Fill in the MAC address that is the MAC _
23. elete the selected port range that will be removed from the port filtering list Delete All Click to delete all the registered entries from the port filtering list Reset Click the Reset button to abort change and recover the previous configuration setting 2 3 13 Firewall IP Filtering Entries in this table are used to restrict certain types of data packets from your local network to Internet through the Gateway Use of such filters can be helpful in securing or restricting your local network IP Filtering Entries in this table are used to restrict certain types of data packets from your local network to Internet through the Gateway Use of such filters can be helpful in securing or restricting your local network Enable IP Filtering Loal IP Address Protocol Comment Current Filter Table 192 168 1201 T 1 L 192 168 1 202 ST 2 Delete Selected Delete All Screen snapshot Firewall IP Filtering Item Description Enable IP Filtering Click to enable the IP filtering security function Local IP Address To restrict data transmission from local Protocol network on certain IP addresses fill in the IP Comments address and the protocol also put your comments on it The Protocol can be TCP UDP or Both Comments let you know about whys to restrict data from the IP address Apply Changes Click the Apply Changes button to register the IP address to IP filtering list Reset Click the Re
24. ferent modes to LAN and WLAN interface for NAT and bridging function Gatewav In this mode the device is supposed to connect to internet via ADSL Cable Modem The NAT is enabled and PCs in LAN ports share the same IP to ISP through WAN port The connection type can be setup in WAN page by using PPPOE DHCP client PPTP client or static IP Bridge In this mode all ethernet ports and wireless interface are bndged together and NAT function is disabled All the WAN related function and firewall are not supported Wireless ISP In this mode all ethernet ports are bridged together and the wireless chent will connect to ISP access point The NAT is enabled and PCs in ethernet ports share the same IP to ISP through wireless LAN You must set the wireless to chent mode first and connect to the ISP AP in Site Survey page The connection type can be setup in WAN page by using PPPOE DHCP chent PPTP chent or static IP Apply Change Screen snapshot Operation Mode Item Description Gateway Traditional gateway configuration It always connects internet via ADSL Cable Modem LAN interface WAN interface Wireless interface NAT and Firewall modules are Bridge Each interface LAN WAN and Wireless regards as bridge NAT Firewall and all Wireless ISP Switch Wireless interface to WAN port and all Ethernet ports in bridge mode Wireless Apply Changes Click the Apply Changes button to complete Reset Click the Reset button
25. hannel Number Select the wireless communication channel from pull down menu Associated Clients Click the Show Active Clients button to open Active Wireless Client Table that shows the MAC address transmit packet receive packet and transmission rate for each associated ee wireless client Enable Mac Clone Take Laptop NIC MAC address as wireless Single Ethernet client MAC address Client Mode only Send Enable Universal Click to enable Universal Repeater Mode Repeater Mode SSID of Extended Assign SSID when enables Universal Repeater Interface Mode Apply Changes Click the Apply Changes button to complete the new configuration setting Reset OO Click the Reset button to abort change and ea Ue 2 3 5 Wireless Advanced Settings These settings are only for more technically advanced users who have a sufficient knowledge about wireless LAN These settings should not be changed unless you know what effect the changes will have on your AP Wireless Advanced Settings These settings are only for moe technically advanced users who have a sufficient knowledge about wireless LAN These settings Should not be changed unless you know what effect the changes will have on your Access Point Authentication Type O Open System Shared Key Auto Fragment Threshold 2546 256 2346 RTS Threshold Air 23471 Heres Utes 20 1024 ms Data Rate Preamble Type Long Preamble Short Preamble Broadcast SSID Enabled Disa
26. nd TCP UDP Portscan sensitivity ICMP Smurf IF Land IF Spoof IF TearDrop PingOMeath TCP Scan TCP Syn WithData UDP Bomb UDP EchoChargen Enable Source IP Blocking Block time sec Screen snapshot Management Denial of Service Item Description Enable DoS Click the checkbox to enable DoS prevention Prevention Whole System Flood Enable and setup prevention in details Per Source IP Flood Select ALL Click the checkbox to enable all prevention items Clear ALL Click the checkbox to disable all prevention items Apply Changes Click the Apply Changes button to save above settings 2 3 23 Management Log This page is used to configure the remote log server and shown the current log System Log This page can be used to set remote log server and show the system leg Enable Loz system all Cl Enable Remote Loz Oday 00 02 18 brO port 2fwlanl entering disabled state Oday 00 02 18 device wlan left promiscuous mode Oday OO 02 18 br port lfieth0 entering disabled state Oday 00 02 18 device eth left promiscuous mode Oday 00 02 18 device eth entered promiscuous mode Oday 00 02 18 eth0 phy is 8305 Oday 00 02 18 device wlan entered promiscuous mode day 00 02 18 brl port 2fwlanl entering listening state Oday OO 02 18 bri port lieth0 entering listening state Oday 00 02 18 entering learning state Oday 00 02 14 bri port 2iwlanO entering forwarding state Oday 00 02 14
27. nfigure the parameters for Intemet network which connects to the WAN port of your Access Point Here you may change the access method to static IP DHCP PPPoE or PPTP by click the iter value of WAN Access type WAN Access Type User Name Password Service Name Connection Type Idle Time 1 1000 minutes MTU Size 1360 1492 bytes Attain DNS Automatically Set DNS Manually DNS 1 168 95 1 1 DNS 2 DNS 3 Clone MAC Address 192 168 0 5 0 0 0 0 OO0000000000 Enable uPNP Enable Ping Access on WAN Enable Web Server Access on WAN Enable IPsec pass through on VPN connection Enable PPTP pass through on VPN connection Enable L2TP pass through on VPN connection Set TIL Value 6 amp 4 1 128 CRC oO Screen snapshot WAN Interface Setup PPPoE Item PPPoE Service Name Description Click to select PPPoE support on WAN interface There are user name password connection type and idle time settings need to be done If you select the PPPoE support on WAN interface fill in the user name and password to login the PPPoE server If you select the PPPoE support on WAN interface fill in the user name and password to login the PPPoE server Fill in the service name of Service Name The default value is empty Connection Type Select the connection type from pull down menu There are Continuous Conne
28. nizing with a public time server over the Internet Current Time Yr Mon Day Hr Mn Sec Time Zone Select 00 Enable NTP client update NTP server 19254141 Morth America Ol latere setting Screen snapshot Management Time Zone Settings Item Description Current Time It shows the current time Time Zone Select Click the time zone in your country Enable NTP client Click the checkbox to enable NTP client update update NTP Server Click select default or input NTP server IP address Apply Change Click the Apply Changes button to save and enable NTP client service Reset Click the Reset button to abort change and recover the previous configuration setting Refresh Click the refresh the current time shown on the screen 2 3 22 Management Denial of Service This page is used to enable and setup protection to prevent attack by hacker s program It provides more security for users Denial of Service A denial of servace DoS attack ic characterized by an explicit attempt by hackers to prevent eevtomate users of a service from vang thet terria Enable DoS Preventicn Whole System Flood Packets Second Whole System Flood Packets Second Whole System Flood Packets Second Whole System Flood Packet Second Per Source IF Flood Packets Second Per Source IF Flood Packets Second Per Source IP Flood Packets Second Per Source IF Flood Packets Seco
29. o complete Click to Enable and set Time to Live value the new configuration setting Reset Click the Reset button to abort change and TE OVE ME PI VOU eoi EU onet 2 3 12 Firewall Port Filtering Entries in this table are used to restrict certain types of data packets from your local network to Internet through the Gateway Use of such filters can be helpful in securing or restricting your local network Port Filtering Entries in this table are used to restrict certain types of data packets from your local network to Internet through the Gateway Use of such filters can be helpful in securing or restricting your local network Enable Port Filtering Port Range ae En Protocol Comment E Current Filter Table 20 21 TCP UDP FIP F Delete Selected Delete All Screen snapshot Firewall Port Filtering Item Description Enable Port Filtering Click to enable the port filtering security function Port Range To restrict data transmission from the local Protocol network on certain ports fill in the range of Comments start port and end port and the protocol also put your comments on it The Protocol can be TCP UDP or Both Comments let you know about whys to restrict data from the ports Apply Changes Click the Apply Changes button to register the ports to port filtering list Reset Click the Reset button to abort change and recover the previous configuration setting Delete Selected Click to d
30. on the Ethernet LAN interface Ethernet WAN It shows the statistic count of sent packets on Sent Packets the Ethernet WAN interface Ethernet WAN It shows the statistic count of received packets Received Packets on the Ethernet WAN interface Refresh Click the refresh the statistic counters on the screen 2 3 20 Management DDNS This page is used to configure Dynamic DNS service to have DNS with dynamic IP address Dynamic DNS Setting Dynamic DNS is a service that provides you with a valid unchanging internet domain name an URL to zo with that possibly everchanging IP address C Enable DDNS Service Provider Note For IZO vou can have a 30 davs free trial here or manage vour IZO account in control panel m aa es a 7 For DynDNS you can create your DynDNS account here Screen snapshot Management DDNS Item Description Enable DDNS Click the checkbox to enable DDNS service Service Provider Click the drop down menu to pickup the right ie 2 Domain Name To configure the Domain Name Password Key Configure Password Key oe Apply Change Eg C lick the Apply Changes button to save the enable DDNS service Reset E C lick the Reset button to abort change and recover the previous configuration setting 2 3 21 Management Time Zone Setting This page is used to configure NTP client to get current time Time Zone Setting You can maintain the system time by synchro
31. on to abort change and recover the previous configuration setting Delete Selected Click to delete the selected MAC address that will be removed from the MAC filtering list Delete All Click to delete all the registered entries from the MAC filtering list Reset Click the Reset button to abort change and recover the previous configuration setting 2 3 15 Firewall Port Forwarding Entries in this table allow you to automatically redirect common network services to a specific machine behind the NAT firewall These settings are only necessary if you wish to host some sort of server like a web server or mail server on the private local network behind your Gateway s NAT firewall Port Forwarding Entries in this table allow you to automatically redirect common network services to a specific machine behind the NAT firewall These settings are only necessary if you wish to host some sort of server like a web server or mail server on the private local network behind your Gateways NAT firewall Enable Port Forwarding IP Address Protocol Port Range a iz Comment 7 Current Port Forwarding Table FIP 192 168 1201 TCP UDP 20 21 Delete Selected Delete All Screen snapshot Firewall Port Forwarding Item Description Enable Port Click to enable the Port Forwarding security Forwarding function IP Address To forward data packets coming from WAN to Protocol a specific IP address that hosted in local
32. perties button on the Network dialog box Select Specify an IP address and type in values as following example v IP Address 192 168 1 1 any IP address within 192 168 1 1 to 192 168 1 253 is good to connect the Wireless LAN Access Point v IP Subnet Mask 255 255 255 0 Click OK to completes the IP parameters setting For OS of Microsoft Windows NT l Click the Start button and select Settings then click Control Panel The Control Panel window will appear Move mouse and double click the right button on Network icon The Network window will appear Click Protocol tab from the Network window Check the installed list of Network Protocol window If TCP IP is not installed click the Add button to install it otherwise go to step 6 Select Protocol in the Network Component Type dialog box and click Add button Select TCP IP in Microsoft of Select Network Protocol dialog box then click OK button to install the TCP IP protocol it may need the Microsoft Windows CD to complete the installation Close and go back to Network dialog box after the TCP IP installation 6 Select TCP IP and click the properties button on the Network dialog box 7 Select Specify an IP address and type in values as following example v IP Address 192 168 1 1 any IP address within 192 168 1 1 to 192 168 1 253 1s good to connect the Wireless LAN Access Point YIP Subnet Mask 255 255 255 0 8 Click OK to complete the IP parameters setting 2 2 Connect to the
33. pposed to connect to internet via ADSL Cable Modem The NAT is enabled and PCs in four LAN ports share the same IP to ISP through WAN port The connection type can be setup in WAN page by using PPPOE DHCP chent PPTP chent or static IP Bridge In this mode all ethernet ports and wireless interface are bridged together and NAT function is disabled All the WAN related function and firewall are not supported Wireless ISP In this mode all ethernet ports are bridged together and the wireless chent will connect to ISP access point The NAT is enabled and PCs in ethernet ports share the same IP to ISP through wireless LAN You must set the wireless to chent mode first and connect to the ISP AP in Site Survey page The connection type can be setup in WAN page by using PPPOE DHCP client PPTP chent or static IP Screen snapshot Operation Mode Time Zone Setting This page is used to enable and configure NTP client 2 Time Zone Setting You can maintain the system time by synchrorizing with a public time server over the Internet C Enable NTP client update Time Zone Select NIF server Screen snapshot Time Zone Settings LAN Interface Setup This page is used to configure local area network IP address and subnet mask 3 LAN Interface Setup This page is used to configure the parameters for local area network which connects to the LAN port of your Access Point Here you may change the setting for IP add
34. resss subnet mask DHCP etc IP Address Subnet Mask Screen snapshot LAN Interface Setup WAN Interface Setup This page is used to configure WAN access type 4 WAN Interface Setup This page is used to configure the parameters for Internet network which connects to the WAN port of your Access Point Here you may change the access method to static IP DHCP PPPoE or PPTP by click the item value of WAN Access type WAN Access Type DHCP Client Screen snapshot WAN Interface Setup Wireless Basic Settings This page is used to configure basic wireless parameters like Band Mode Network Type SSID Channel Number Enable Mac Clone Single Ethernet Client 5 Wireless Basic Settings This page is used to configure the parameters for wireless LAN clients which may connect to your Access Point Band Mode Network Type ssm Channel Number ll w Enable Mac Clone Single Ethernet Client Screen snapshot Wireless Basic Settings Wireless Security Setup This page is used to configure wireless security 6 Wireless Security Setup This page allows you setup the wireless security Tum on WEP or WPA by using Encryption Keys could prevent any unauthorized access to your wireless network Encryption 4 feoiedd Screen snapshot Wireless Security Setup 2 3 3 Operation Mode This page is used to configure which mode wireless broadband router acts Operation Mode You can setup dif
35. s the IP subnet mask of LAN oe interfaces of AP Default Gateway It shows the default gateway setting for LAN MAC Address It shows the MAC address of LAN interfaces WAN configuration Attain IP Protocol It shows how the AP gets the IP address The IP address can be set manually to a fixed one or set dynamically by DHCP server or attain IP by PPPoE PPTP connection eesceccscsccscscsccscscsccscecsscscecescecscsscecsscscececcscecescececescececcscecsscececcecececcececsccececcecececeacececcececeecececcececescecesescecescsceasscececsscececsececessscscescecscescecesescscsscesesescssssesssssszssssse Subnet Mask It shows the IP subnet mask of WAN interface of AP 2 3 2 Setup Wizard This page guides you to configure wireless broadband router for first time Setup Wizard The setup wizard will guide you to configure access point for first time Please follow the setup wizard step by step Welcome to Setup Wizard The Wizard will guide you the through following steps Begin by clicking on Next Setup Operation Mode Choose your Time Zone Setup LAN Interface Setup WAN Interface Wireless LAN Setting Wireless Security Setting 1 2 3 4 3 6 Screen snapshot Setup Wizard Operation Mode This page followed by Setup Wizard page to define the operation mode 1 Operation Mode You can setup different modes to LAN and WLAN interface for NAT and bridging function Gatewav In this mode the device is su
36. sed to show VPN connection table configure IPSEC VPN NAT Traversal Generate RSA Key Show RSA Public Key VPN Setup This page i used to enabledisable WEN function and select a VPN connection to editidelete Enable IPSEC WPN Enable NAT Traversal Generate BSA Key Show RSA Public Rey WAN IP 192 16 3 254 ol l sites 12 1681 O24 192 168 4024 192 168 3 1 t e IE g e E e E e IK OD e IE 10 Screen snapshot VPN Setup Item Description Enable IPSEC VPN Click to enable IPSEC VPN function Enable NAT Click to enable NAT Traversal function Traversal Generate RSA Key Click to generate RSA key Show RSA Public Click to show RSA public key that we Key generate Apply Changes Delete Refresh Click the Apply Changes button to enable IPSEC VPN NAT Traversal settings It shows current WAN interface information l and VPN connection table Click to enter the current VPN tunnel configuration page Click to delete the current VPN tunnel that radio button stay Click to refresh the current VPN connection VPN Setup Edit Tunnel VPN Setup Enable Tunnel 1 Connection Name Auth Type Local Site Local F Address Network Local Subnet Mask Remote Site Remote Secure Gateway Remote F Address Network Remote Subnet Mask Local Peer ID Local ID Type Leval ID Remote ID Type Remote ID eo a Ie Rell El a HEIRE R B a l EISEN D D 4 Screen snapshot
37. set button to abort change and recover the previous configuration setting Delete Selected Click to delete the selected IP address that will be removed from the IP filtering list Delete All Click to delete all the registered entries from the P filtering list Reset Click the Reset button to abort change and recover the previous configuration setting 2 3 14 Firewall MAC Filtering Entries in this table are used to restrict certain types of data packets from your local network to Internet through the Gateway Use of such filters can be helpful in securing or restricting your local network MAC Filtering Entries in this table are used to restrict certain types of data packets from your local network to Internet through the Gateway Use of such filters can be helpful in securing of restricting your local network Fnable MAC Filtering MAC Address Comments Current Filter Table 00 02 72 00 51 90 00 02 72 00 81 P1 Delete Selected Delete All Screen snapshot Firewall MAC Filtering Miser Enable MAC Click to enable the MAC filtering security Filtering OO e a MAC Address To restrict data transmission from local Comments network on certain MAC addresses fill in the MAC address and your comments on it Comments let you know about whys to restrict data from the MAC address Apply Changes Click the Apply Changes button to register the MAC address to MAC filtering list Reset Click the Reset butt
38. stall the TCP IP protocol it may need the Microsoft Windows CD to complete the installation Close and go back to Network dialog box after the TCP IP installation Select TCP IP and click the properties button on the Network dialog box Select Specify an IP address and type in values as following example v IPAddress 192 168 1 1 any IP address within 192 168 1 1 to 192 168 1 253 is good to connect the Wireless LAN Access Point v IP Subnet Mask 255 255 255 0 Click OK and reboot your PC after completes the IP parameters setting For OS of Microsoft Windows 2000 XP l 8 Click the Start button and select Settings then click Control Panel The Control Panel window will appear Move mouse and double click the right button on Network and Dial up Connections icon Move mouse and double click the Local Area Connection icon The Local Area Connection window will appear Click Properties button in the Local Area Connection window Check the installed list of Network Components If TCP IP is not installed click the Add button to install it otherwise go to step 6 Select Protocol in the Network Component Type dialog box and click Add button Select TCP IP in Microsoft of Select Network Protocol dialog box then click OK button to install the TCP IP protocol it may need the Microsoft Windows CD to complete the installation Close and go back to Network dialog box after the TCP IP installation Select TCP IP and click the pro
39. to abort change and recover the previous configuration setting 2 3 4 Wireless Basic Settings This page is used to configure the parameters for wireless LAN clients that may connect to your Broadband Router Here you may change wireless encryption settings as well as wireless network parameters Wireless Basic Settings This page is used to configure the parameters for wireless LAN chente which may connect to your Access Point Here you may change wireless encryption settings as well as wireless network parameters C Disable Wireless LAN Interface Band 2 4 GHz B G w Mode AP Network Type SSID MAAALA Channel Number Associated Clients Show Active Clients Enable Mac Clone Single Ethernet Client Enable Universal Repeater Mode Acting as AP and client simultaneouly SSID of Extended Interface O O Apply Changes Screen snapshot Wireless Basic Settings Item Description Disable Wireless Click on to disable the wireless LAN data LAN Interface transmission Band Click to select 2 4GHz B 2 4GHz G 2 4GHz B G Mode nn Click to select the WLAN AP Client WDS OO AP WDS wireless mode Site Survey The Site Survey button provides tool to scan the wireless network If any Access Point or IBSS is found you could choose to connect it manually when client mode is enabled Refer to Be 3 3 9 Site Survey SSID It is the wireless network name The SSID can Be be 32 bytes long C
40. to disconnect manually Responder mode only ESP Click to configure 3DES AES128 or NULL encryption Click to configure MDS or SHAI authentication PreShared Key Fill in the key value IKE mode only Remote RSA Key Fill in the remote gateway RSA key IKE nn mode only Status It shows connection status IKE mode only SPI Fill in Security Parameter Index value Manual mode only Encryption Key Fill in encryption key Manual mode only Authentication Key Fill in authentication key Manual mode only Apply Change Click the Apply Changes button to save current tunnel settings Reset Click the Reset button to abort change and recover the previous configuration setting Refresh It shows the current connection status Manual mode only Back It returns back to VPN Setup page Advanced IKE Setup Adavnced VPN Setting for IKE This This page 1s used to provide advanced setting for IEE mode Tunnel Phase 1 Nezotation Mode Encryption Algorithm Authenticaiton Algorithm Ker Group Eey Lite Time Phase 2 Acte Protocol Encryption Algorithm Authenticaiton Algorithm Eey Lite Time Feapsulation Perfect Forward Secrecy PRS Screen snapshot Advanced VPN Settings for IKE Item aoa ee eee Encryption Click to select 3DES or AES128 encryption Authentication Click to select MD5 or SHAI authentication Key Group Click to select DH 1 modp768
41. up Item Descriptio IP Address Fill in the IP address of LAN interfaces of this 506 CCS U Subnet Mask Fill in the subnet mask of LAN interfaces of ee Default Gateway Fill in the default gateway for LAN interfaces out gomg data packets DHCP Click to select Disabled Client or Server in different operation mode of wireless Access allocate a range of IP addresses client with DHCP function set will be assigned an IP Show Client Click to open the Active DHCP Client Table window that shows the active clients with their assigned IP address MAC address and time EADS Od OND CEVEE Mode oniy DNS Server Manual setup DNS server IP address Domain Name Assign Domain Name and dispatch to DHCP oe eee 802 1d Spanning Select to enable or disable the IEEE 802 1d MOONEN En Clone MAC Fill in the MAC address that is the MAC GENE ee Apply Changes Click the Apply Changes button to complete Reset Click the Reset button to abort change and recover the previous configuration setting 2 3 11 WAN Interface Setup This page is used to configure the parameters for wide area network that connects to the WAN port of your AP Here you may change the access method to Static IP DHCP PPPoE or PPTP by click the item value of WAN Access Type Static IP WAN Interface Setup This page is used to configure the parameters for Intemet network which connects to the WAN port of your Access Point Here you may change the access method to
42. y Access Point or B55 15 found you could choose to connect rt Toanually when client mode is enabled hoy LAN OOM 2008186 11 BH linwx wlan OOO at Oe ad 6 BI ETLI iE VEH GW gedde 81 56 23 11 B AP ne AP 76 66 AP ales DOO 72 04 68 92 11 B AF 53 AF OO 0e 72 00 95 Th a Bi 35 dEdedetd 2 d4 iB Adho 32 00 00 72 85 15 99 11 B G AP 32 Screen snapshot Wireless Site Survey Oe el SSID Ttshows the SSIDof AP BSSID Ttshows BSSID of AP Channel It show the current channel of AP occupied Type Ttshow which type AP acts Encrypt It shows the encryption status Signal Tt shows the power level of current AP Select Click to select AP or client you d like to connect eee Refresh Click the Refresh button to re scan site survey on the screen Connect Click the Connect button to establish connection 2 3 10 LAN Interface Setup This page is used to configure the parameters for local area network that connects to the LAN ports of your AP Here you may change the setting for IP address subnet mask DHCP etc LAN Interface Setup This page is used to configure the parameters for local area network which connects to the LAM port of your Access Point Here you may change the setting for IP addresses subnet mask DHCP etc IP Address 192 168 1 254 Subnet Mask oe 255 255 0 Default Gateway 0 0 0 0 DNS Server fs 802 1d Spanning Tree Clone MAC Address Screen snapshot LAN Interface Set
Download Pdf Manuals
Related Search