RPM 2001 RPM 2001 MINI RPM 2005 RPM 2006 RPM 2007
Contents
1. file nr 235 RPM 2001 RPM 2001 MINI RPM 2005 RPM 2006 RPM 2007 RPM AVIO GET CRA I RDS ECHNMNMIOLOCG GPT ENGINEERING VIA CADORE 19 20038 SEREGNO MONZA BRIANZA ITALY PHONES 390362231023 FAX 390362239002 tech gpt it www gpt it The POWER RPM digitali s a small and powerfull tool that gives the driver information useful to evacuate driving performance and the tuning of vr vehicle the POWER RPM in accord with several versione will displav RPM engine water temperature in C9 or F9 with custom set up for 2 or 4 strokes from 1 to 24 cvlinders maximum RPM recall set up limit rpm led laser flashing for limit rpm and alarm temperature count down battery power supply by one internal battery PC version or 12 volts battery life 100 hrs Three differets way sto signal acquisitions from spark plug wire from negative coil or from electri cal manage injection system called EFI Digital watch when device turned off Fitting instruction Code version RPM 2001 RPM 2003 only rpm Version with battery on board fit the rpm wire the little alligator directly on the spark plug wire if there is present an insulated cable or special spark plug caps make two or three round of the cable bifore to fit the clip In 12 volts power supply the green wire is the positive and the white wire is the negative to ground the yellow is the for the backlight In case you have to fit the rpm cable into negative coil tak2. the set up is complete turn off the device tostore all the parameters selcted Features Turn on off push P1 for half second the version 12 volts 12 volts the turn on is automatically when arrive power Engine hours push P1 without release it and will appear the time Max rpm reached push P4 Liquid cooling temperature push P3 to return to rpm push P4 Rev Limited when you arrive to rev limited the red led flashing Alarm liquid cooling in accord with set up the red flashing IMPORTANT NOTES AND SUGGESTIONS the battery life is around 100 hrs the model to replace is 3v lithium CR 2430 when you replace it the pole must be to the up Do not pair rpm wire with others wires the rpm cable must be alone With the acquisition signal from spark plug wire take note if you have the wire and the spark plug insulated because in this case you must around the wire two or three time on the spark plug wire as the wave with the insulated cables are too low The power rpm can stand the exposure to the dust and the bad weather
3. e off the alligator and fit the cable Is pos sibile cut the rpm cable without problem Do not pair the tachometer wire with power supply one Code version RPM 2002 RPM 2004 only rpm Version with battery on board with EFI acquisition signal Connect the red cable efi WIRE directly to exit of central manage system EFI and the white cable to ground please see yr user manual of yr vehicle to find the correct wires in output In the back lite version you ll find three wires white negative to ground green to 12 volts and yellow 12v for the light Code version RPM 2005 RPM 2006 RPM 2007 RPM 2010 with temperature Version with battery on board there are present two wires one for the rpm as usual with alligator and another one for the water probe connect the fastom red wire directly to probe and the other white wire on ground directly to the T aluminium adaptor you must connect the positive wire on probe and the negative wire directly on adapter If you use some plastic tie wraps don t tighen them too much and rem mber not top air tachometer wire with the temperature one Code version RPM 2008 RPM 2009 with temperature Connect the power supply 12v green wire positive and white wire negative to ground and the yellow for the backlight Power 12v after connect the temperature wire Temp with the red wire positive directly to probe and the white wire negative to ground on chassis Now connect the rpm wire direct
4. ly to manage system EFI see version 2002 and 2004 see the user manual of vehicle manufacturer where is the output signal and connect the red wire positive while the white wire to ground If you use some plastic tie wraps don t tighen them too much and remember not top air the tachometer wire the temperature one In the drawing are presents four buttons called P1 P2 P3 P4 Digital watch The first operation is to set the digital watch i twill displav hours minutes and seconds in 24h format To set the time push P2 without release it and push P3 at this time hours flashing set the correct time with P4 the same for minutes and second P3 gt P4 after selected the minutes and seconds release P2 and the set up is finish If you don t want to display the watch push P3 and Pi to restore the watch push again P3 and P1 Tachometer Turn on the device with P1 push for half second now push P2 for two seconds to enter in set up menu at this point will appear T 2 2 or 4 strokes menu to select use P3 and P4 after push P2 P 1 nr of cilinders menu to select use P3 and P4 after push P2 H 2900 rpm limit set up to select use P3 and P4 after push P2 ST 50 rpm s engine reading per minute select with P3 and P4 suggest to select 100 after push P2 version with water temperature push again P2 and C select F or C menu with P3 or P4 after push P2 C 80 alarm water temperature select the alarm temp with P3 or P4 now
Download Pdf Manuals
Related Search