MHD44TP
Contents
1. 26 9 Safety Operation Guide iiti iR Loon o deste oua eee 27 10 After sales ener nnne 28 PTN Electronics Limited www PTN electronics com HDBaseT Matrix Switcher 4x4 1 Introduction 1 1 Introduction to MHD44TP MHD44TP is a 4x4 HDBaseT matrix switcher including 4 HDMI inputs 4 HDBaseT outputs 2 local HDMI outputs 4 de embedded stereo audio amp 4 de embedded digital audio outputs It enables cross point switching from any input to any output and supports high resolution 1080P HD3D The HDBaseT output can works with TPHD402PR to transmit HDMI IR RS232 and POE over a Cat5e Cat 6 cable And its transmission distance can up to 60 meters 1 2 Features HDTV compatible with High Definition Transmission resolution up to 1920 1200 60Hz supports 1080P 24Hz HDCP Compliant and DVI compatible supporting HDMI 1 4a amp DVI1 0 Powerful EDID amp HDCP management HDBaseT outputs to transmit HDMI IR amp RS232 to 60 meters long distance over a Cat5E 6 cable POE supports provides power for all the receivers connected to HDBaseT outputs Supports multiple control ways including front panel RS232 IR and optional TCP IP control works with PTNET IR OUT signal switching follow with video signal also can be broken away from video switching Supports remote control from receiver by IR amp RS22. 5 2 1 Usage IR Remote Menu buttons AV and ALL buttons have the same function as the front panel THROUGH To transfer the signals directly to the corresponding output channels Example Press 3 THROUGH the result will be IN 3 OUT 3 Press ALL THROUGH the result will be 121 222 323 494 Output channels range from 1 4 Each channel has 1 IR IN 1 COAX 1 HDBaseT 1 1 RS232 and 1 AUDIO outputs and channel No 1 amp i No 2 has 1 HDMI output 5 2 2 IR Operations 1 IR Matrix Switching The 4 IR OUT ports make up a 4x4 IR matrix with the IR IN ports of the far end receivers See as below PTN Electronics Limited 10 www PTN electronics com LL IR Transmitter 2 sr 4 Ung coax coax RSfO AUDIO TPHD402R 2 TPHD402R 3 TPHD402R 4 159 TRIN HOMIOUT OUT REAN 9 Te e DVD gt h w HDTV R Receiver R Receiver R Receiver R Receiver Control Local Devices or MHD44TP Remotely HDBaseT Matrix Switcher 4x4 The IR signal is received from corresponding remote controller then transferred to HDBaseT receiver then to corresponding zone of MHD44TP through the twisted pair finally transferred to IR OUT port and received by controlled device Switching Operation a Sending command reference to 5 3 RS232 Control x1 R x2 x1 Corresponding to the 4 IR OUT ports of MHD44TP
3. PTN Electronics Limited 15 www PTN electronics com HDBaseT Matrix Switcher 4x4 PTN EDIDM X B Y Manually EDID switching Copy the EDID data of output X to the input Y Upgrade EDID data via the RS232 port X is for input port when the value of X is 5 it EDIDUpgrade means to upgrade to all input ports When the x switcher gets the command it will show a message to send EDID file bin file Operations will be canceled after 10 seconds Note 1 Please cut off all connections of HDBaseT ports 9 0801 Automatically HDCP management Input is with HDCP so is output 960800 Manually HDCP management 960900 Set as infrared carrier following mode 960901 Set as infrared carrier enforcing mode 960911 Reset to factory default 969951 Check the command sent by port 1 when PWON 969952 Check the command sent by port 2 when PWON 969953 Check the command sent by port 3 when PWON 969954 Check the command sent by port 4 when PWON 969955 Check the command sent by port 1 when PWOFF 969956 Check the command sent by port 2 when PWOFF 969957 Check the command sent by port 3 when PWOFF 969958 Check the command sent by port 4 when PWOFF 969961 Check the system locking status 969962 Check the status while in standby mode 969963 Check the working mode of infrared carrier 969971 Check the connection status of the inputs 969972 Ch
4. 99232 connects with control device such as a PC Power 8 indicator Turn red and keep on when power on 48VDC Connect with 48V DV power adaptor amp GROUND Connect to grounding make the unit ground well TCP IP TCP IP port for unit control optional function i i he IR IR EYE Connect with extended IR receiver use the IR remote to control MHD44TP 2 3 Connection with RS232 Communication Port Except the front control panel MHD44TP can be controlled by far end control system through the RS232 communication port This RS232 communication port is a female 9 pin D connector The definition of its pins is as the table below No Pin Function 1 N u Unused 5 1 2 Tx Transmit 3 Rx Receive 1 00000 4 N u Unused 5 Gnd Ground d 6 N u Unused 9 6 6 7 N u Unused Female 8 N u Unused 9 N u Unused PTN Electronics Limited www PTN electronics com HDBaseT Matrix Switcher 4x4 2 4 Twisted Pair Cable Connection The cables for HDBaseT ports must be straight through ones using T568A or T568B standard TIA EIA T568A TIA EIA T568B Pin Cable color Pin Cable color 1 green white 1 orange white 2 green 2 orange 3 orange white 3 green white 4 blue 4 blue 5 blue white 5 blue white 6 orange 6 green 7 brown white 7 brown white 8 brown 8 brown 1st Ground 4 5 1st Ground 4 5 2nd Ground 3 6 2n
5. Apply Reset Value PTN Electronics Limited 21 www PTN electronics com HDBaseT Matrix Switcher 4x4 PTN b Press the button Apply to save your settings Then the PC s in this LAN connected with this router will be able to control MHD44TP Change Serial Port a Select the tab serial info and then you are able to change the serial port Select apply Serial Port COM1 Apply All Serial Parameters The baud rate is the same as MHD44TP s Data bits 8 Stop bits uM Parity bits None Flow control None v Clear serial buffer Never v Data Packing PTN Electronics Limited 22 www PTN electronics com HDBaseT Matrix Switcher 4x4 b Set the port number to 4001 unique other number are unavailable as the picture below Packing length 500 Gap time 50 0 2 9999ms Start byte 0 HEX Stop byte 0x HEX Operating Parameters Operating mode Server TCP alive check time 20 0 60000s Inactivity time 0 0 60000 10ms Max connection 1 174 port 4001 2 Set as 4001 TCP turbo Enable TCP close when cable break Disable TCP connect password Disable TCP connect and send Nothing connect condition Startup IO Function Link Status v c Press the button Apply on present page
6. AV for 3 seconds it will enter into system inquire menu Use Left and Right direction button two check the previous next item Function Items Example Description Check the connection status of inputs In Connect Y means the corresponding port is connected with input device N means not Check the connection status of outputs Connect Y means the corresponding port is connected with output device N means not Correspondence between inputs and outputs Shows the correspondence between the 4 inputs and 4 outputs output is with HDCP Check if the Y means the input signal is with input is with HDCP N means not HDCP Check if the Y means the output signal is with HDCP N means not Check the output resolution Resolution Out 1 1920x1080 Use the UP and DOWN direction button to check all the 4 output resolutions 5 2 IR Control By using IR amp HDBaseT transmission technology MHD44TP has some functions as follows 1 Control far end output device from local 2 Control local input output device remotely 3 Control MHD44TP locally remotely MHD44TP can be controlled by its built in IR receiver or through the IR EYE port by connecting with extended IR receiver or even can be controlled remotely by a far end IR device through the twisted pair PTN Electronics Limited www PTN electronics com HDBaseT Matrix Switcher 4x4
7. MHD44TP PTN HDBaseT Matrix Switcher 4x4 All Rights Reserved Version MHD44TP20131 0 E www PTN electronics com HDBaseT Matrix Switcher 4x4 NOTICE Please read this user manual carefully before using this product This manual is only for operation instruction only not for any maintenance usage The functions described in this version are updated till May 2013 Any changes of functions and parameters since then will be informed separately Please refer to the dealers for the latest details This manual is copyright PTN Electronics Limited All rights reserved No part of this publication may be copied or reproduced without the prior written consent of PTN Electronics Limited All product function is valid till 2013 05 29 Update History Version Date Update Content 1 0 2013 05 29 First version PTN Electronics Limited www PTN electronics com HDBaseT Matrix Switcher 4x4 Table of Contents LN orte Em 1 1 1 Introduction to MHDAATP 1 1 2 ul xcv 1 1 3 Package Contents iik ete de Ea anb RR aa he P 1 2 Product Appearance of 44 2 2 1 Front Pariel a dex ere 2 2 2 MT 3 2 3 Connection with RS232 Communication Port esses 4 2 4 Twisted Pair Cable 5 3
8. Female Female p Female RJ45 with LED Connector Connector a indicators Input Level T M D S 2 9V 3 3V Output Level T M D S 2 9V 3 3V input 1000 Differential Output 1009 Differential Impedance Impedance Gain 0 dB Bandwidth 6 75Gbit s Maximum Video Signal HDMI or DVI D Pixel Clock 165MHz Resolution Up to 1920 x 1200 or Switching Range 1080P 60Hz Speed SUIS AME Transmigsion 60m with POE Distance EDID In built EDID data and manual EDID management Management HDCP Supports HDCP 1 3 auto and manual HDCP management Stereo audio Output Output Signal Digital audio Connector connectors 9 4 Coax RCA Earphone output Stereo estoton Coax Supports PCM Dolby Output eee ee Output DTS 5 1 0 1 160 105mW i KHz Frequency gt 90dB 20Hz Eisen 20Hz 20KHz CMRR 20KHz 4 IR OUT green 4 IR IN black 1 IR EYE black Control Ports 1 TCP IP female RJ45 Panel Control Front panel buttons 1 RS232 9 pin female D 4 RS232 3p captive screw connectors IR Default IR remote TCP IP Works with PTNET2 2 PTN Electronics Limited 25 www PTN electronics com HDBaseT Matrix Switcher 4x4 Extend IR EYE Control PONET Input 100VAC Power SEI 240VAC 50 60Hz 48W Output DC48V 1 6A Temperature 20 70 C Humidity 10 90 W483 x H44 x Casa D235mm 1U high full Product 1 8Kg Dimension Weight rack wide 7 Panel Drawing 482 6
9. 7 DO NOT splash any chemistry substance or liquid in the equipment or around PTN Electronics Limited 27 www PTN electronics com HDBaseT Matrix Switcher 4x4 10 After sales Service 1 2 3 4 If there appear some problems when running MHD44TP please check and deal with the problems reference to this user manual Any transport costs are borne by the users during the warranty You can email to our after sales department or make a call please tell us the following information about your cases Product version and name Detailed failure situations The formation of the cases We offer products for all three year warranty which starts from the first day you buy this product The purchase invoice shall prevail Any problem is same with one of the following cases listed we will not offer warranty service but offer for charge Beyond the warranty Damage due to incorrectly usage keeping or repairing Damage due to device assembly operations by the maintenance company non assigned Nocertificate or invoice as the proof of warranty The product model showed on the warranty card does not match with the model of the product for repairing or had been altered Damage caused by force majeure Remarks For any questions or problems please try to get help from your local dealer or to email at support PTN electronics com PTN Electronics Limited 28 www PTN electron
10. System 5 3 1 Usage Precautions 5 2 ERRORI 5 3 2 System ceu eee etum iid et t t ttai ite E e ERE ei Yee 6 3 9 Connection Procedure ihres tiit 6 3 4 System Applications nene 7 4 Application Solution nennen nnne 7 5 System Operations 9 5 Button Control ende idee 9 5 2 IR Gontroll Ei amie etum pdt uut 9 5 2 1 Usage of IR Remote 10 5 2 2 4 Rt Operations e ee Ini Leto be EL 10 5 3 232 M 14 5 3 1 R8232 2 ated diet Ere pd 14 5 3 2 Control MHD44TP 5 3 3 Control 3rd Party Device from 18 5 3 4 Bi directional RS232 18 5 4 TCP IP Control ccccccccsccceccsneeeessceceeseneeeceneeeeeneaeeessaeeesceeeeesseeeeesseeeeseneeeess 18 5 4 1 Control Modes 2 0 0 eecceceseeseneeeeceseseeeeaeeeeseeeseeeseaeeesaesesaeesaeesaeessaeeeaaee 18 5 4 2 TOP IP S tlingS ete eana o RENE GERE TERES 20 5 5 USB Firmware nennen nene 24 6 SPECICATION o o ees exei irae 25 7 ducis M 26 8 Troubleshooting amp Maintenance
11. The IR emitter connected to this port can be placed at IR receiving area of output device or MHD44TP itself x2 Corresponding to the zone receive IR signal from HDBaseT receiver with IR IN port connects with IR receiver number of MHD44TP E g Command 2 means to transfer IR signal received from zone 2 to IR OUT port 3 b Using IR remote Input channel button IR Output channel Input channel the 4 INPUTS buttons corresponding to the 4 IR OUT ports of MHD44TP Output channel the 4 OUTPUTS buttons corresponding to the zone receive IR signal from HDBaseT receiver with IR IN port connects to IR receiver number of MHD44TP E g Press buttons 3 IR 1 in order 3 in OUTPUTS area 1 in INPUTS area to transfer IR signal received from zone 3 to IR OUT port 1 Note When switch all the 4 IR input signal channels to a same IR out channel it is not able to control the controlled device s at the same time 2 IR Carrier Enforcing a Only if the IR receiver connected with HDBaseT receiver is with IR carrier the received IR signal can be transferred to IR OUT port of MHD44TP b Only if the IR receiver connected with IR ALL IN port of MHD44TP is with IR carrier the received IR signal can be transferred to IR OUT port of MHD44TP If the IR receiver connected with HDBaseT receiver or IR ALL IN port of MHD44TP is not with IR carrier you need to send the command 960901 and then you are able to transf
12. to save your settings as below Destination IP address 1 Port 116001 Destination IP address 2 Port 216002 Destination IP address 3 Port 316003 Destination IP address 4 Port 416004 Step6 Select the tab reset device then your settings will be loaded onto MHD44TP PTN Electronics Limited 23 www PTN electronics com HDBaseT Matrix Switcher 4x4 5 5 USB Firmware Updating To meet with the request of different users or add function in future the firmware of MHD44TP can be upgraded USB When you need to upgrade it please download the latest upgrade file and then you are able to upgrade it through the update EXE software Copy the EXE software to the PC in controlled and double chick the program to upgrade the firmware Updata v1 4 1 exe When the program is running normally it will enter into the interface as shown in next figure please press the button and choose the upgrade file downloaded and then press the button It is ready to upgrade When all are done it will appear with a window shows the message Update success Connect USB Update File Note The COM number connected with PC is available only when in 1 to 9 PTN Electronics Limited 24 www PTN electronics com HDBaseT Matrix Switcher 4x4 PTN 6 Specification 2 HDMI Input 4 HDMI Output 4 HDBaseT
13. 0 mm PTN h S 436 40 mm Een min mm MIT 8 Troubleshooting amp Maintenance 1 When there is a color losing or no video signal output maybe the cables have already broken or haven t been connected well ben 44 00 mm 2 When EDID management does not work normally probably the HDMI cable is broken at the output end 3 When switching there is a blank screen on the displayer maybe the displayer does not support the resolution of the video source Switch again or manage the EDID data manually to make the resolution of the video source automatically compliant with the output resolution 4 When user cannot control the switcher by computer through its COM port please check the COM port number in the software and make sure the COM port is in good condition and the communication protocol is correct 5 When switching there is no output image Check if there is any signal at the input Check if there is any signal at the output If there is no signal input output maybe the input output cables broken or the connectors loosen please change for another cable Check if the output port number is the same with the controlled one PTN Electronics Limited 26 www PTN electronics com HDBaseT Matrix Switcher 4x4 e If itis still the same after the above checking maybe there is something wrong in the switcher Please send it to the dealer for repairing 6
14. 32 Supports centralized IR control to control all the remote display devices Supports PCM Dolby and DTS5 1 surround LCD indicator shows connection status switching status HDCP status and output resolution 1 3 Package Contents 1 x 44 2 x Mounting ears 1 x Power adapter DC48V 1 x IR remote 1 x Power cord 1 x RS232 cable 1 x CAT5e twisted pair 1 x IR converting cable 8 x Captive screw connectors 4 x Plastic cushions 1 x User manual VVVVVVVV VV N Notes Please confirm if the product and the accessories are all included if not please contact with the dealers PTN Electronics Limited 1 www PTN electronics com HDBaseT Matrix Switcher 4x4 2 Product Appearance of MHD44TP 2 1 Front Panel x c FM Be e 7 om fe A v 4 5 wes We We 8 o n T ovevs We N AV ALL EDID No Name Description Firmware Micro USB port for update firmware iade Keep light when power on IR Receiver Receive control signal from IR remote ud Real time shows system status Indicator Normal mode Input buttons ranging from 1 to 4 INPUTS amp Menu Inquire mode Press AV more than 3 seconds to enter this mode 4 to change different menus AV to change buttons different channels gt AV synchronal button To transfer AV and IR s
15. HD44TP can be controlled by its built in IR receiver or through the IR EYE port by connecting with external IR receiver The IR signal can also be transmitted bi directionally connect IR OUT port of MHD44TP to IR IN port of other far end IR device and connect IR IN ports of MHD44TP to IR OUT port of other far end IR device and in this mode we can control MHD44TP remotely Note The IR IN port has built in infrared carrier receiver Connect DC48V power adaptor to MHD44TP PTN Electronics Limited 6 www PTN electronics com HDBaseT Matrix Switcher 4x4 3 4 System Applications As its good performance in control and transmission MHD44TP can be widely used in computer realm monitoring large screen displaying conference system television education and bank securities institutions etc 4 Application Solution 979 Speaker 10 80 Video Signal Audio Signa z Signal i k HDBeseT Signal Speaker 10 Rs232 Signal 5 Speaker 10W 80 L 2 Speaker 10W 82 MHD44TP sw TPHD402PR 2 A3 4 PTN control panel p 2 WP8 2 Transmitter 1 52 P pe 4 HDTV AAN P a 221 2 gt ia lt M Laptop NI n d 1 2 S SC61D Q I Blue Ray TA gt 60M Speaker 10W 82 tpe Qe 2 Z we Speaker 10W 80 lt gt Ut PC e 0 09 Speaker 10W 82 9 23 at WP8 R 1 control panel TPHD402
16. If the static becomes stronger when connecting the video audio connectors it probably due to bad grounding please check the grounding and make sure it connected well otherwise it would damage the switcher 7 If the switcher cannot be controlled through the RS232 port front panel buttons or by the IR remote the unit may have already been broken Please send it to the dealer for repairing 9 Safety Operation Guide In order to guarantee the reliable operation of the equipments and safety of the staff please abide by the following proceeding in installation using and maintenance 1 The system must be earthed properly Do not use two blades plugs and ensure the alternating power supply ranged from 100v to 240v and from 50Hz to 60Hz 2 Do not put the switcher in a place of too hot or too cold 3 As the power generating heat when running the working environment should be maintained fine ventilation in case of damage caused by overheat 4 Cut off the general power switch in humid weather or left unused for long time 5 Before following operation ensure that the alternating current wire is pull out of the power supply Take off or reship any components of the equipment Take off or rejoin any pin or other link of the equipment 6 As to non professional or without permission please DO NOT try to open the casing of the equipment DO NOT repair it on your own in case of accident or increasing the damage of the equipment
17. PR A w M N S Transmitter Projector Product Assortment Description D SC61D mini scaler switcher video Inputs 2 x HDMI 1 x VGA 1 x YPbPr 1 x C video amp 1 x S video Upscale to HDMI output at 1080P 3 audio outputs HDMI embedded audio 3 5mm stereo audio and Coaxial SPDIF Output resolutions selectable to assure preferred output Output display H V size adjustable to settle any overscale problem Output display H V position moveable Picture MP3 display via USB Video parameter setting and preset Powerful OSD function with full control support output freeze function Ultra switching for instaneous display HDMI1 3 and HDCP compatible Firmware updatable via USB Front panel lockout PTN Electronics Limited 7 www PTN electronics com HDBaseT Matrix Switcher 4x4 e e e ec eee e eee 40W power amplifier Mono audio output at 40Watt Switchable between 70V and 100V Ducking function 16 ID codes for controlling between different PA3V amplifiers 3 level MIC input supports condenser microphone dynamic microphone and wireless microphone MIC port can support balance unbalance signal suppress the external noise effectively Two stereo audio inputs and one digital audio input switchable by button IR remote amp RS232 Volume Bass Treble controllable by buttons IR remote amp RS232 Fast switching speed for good performance Convection cooler f
18. an is not needed TPHD402P HDMI IR RS232 POE twisted pair extender Support Full HD Delivers high resolution image 1080 60 7 48 b pixels 3D AKx2K Max transmission distance is up to 70 meters over single CAT5e CAT6 cable HDTV Compatible use HDMI 1 4 and HDCP compliant Support POE amp CEC Connect with a displayer to transmit EDID and HPD signals constantly by using a CAT5e cable Use HDBaseT technology Bi directional RS232 IR control WP8 control panel Every button can be programmed to send the bi direction RS232 and RS485 commands simultaneously to control third party devices Every button can be programmed to send the infrared code control the relay to let them work simultaneously to control the third party devices Every button is built in the infrared code and RS232 code learning function and baud rate setting ID looping function 99 WP8 can be looped and controlled together by ID identifying Programmed by USB or RS232 working with PTN PC software PS WP Crystal and backlit buttons with easy user friendly customizable changeable labels The backlit brightness is controllable Dimension 11 4cm long and 7cm wide PTN Electronics Limited 8 www PTN electronics com HDBaseT Matrix Switcher 4x4 PTN 5 System Operations 5 1 Button Control The operation examples are showed in 2 1 Front Panel Here we make a brief introduction to the system inquiry operations Keep pressing the button
19. controlled device and connecting the RS232 port of corresponding HDBaseT receiver with controlled device or PC the RS232 signal is able to be transmitted through the twisted pair bi directionally 5 4 TCP IP Control 5 4 1 Control Modes TCP IP default settings IP is 192 168 0 178 Gateway is 192 168 0 1 and Serial Port is 4001 IP amp Gateway can be changed as you need Serial Port cannot be changed Controlled by PC without network accessing Connect a computer to the TP port of MHD44TP and set its IP address and gateway to the same IP section as the default IP of MHD44TP 192 168 0 178 PTN Electronics Limited 18 www PTN electronics com HDBaseT Matrix Switcher 4x4 r Internet Protocol Version 4 TCP IPv4 Properties General You can get IP settings assigned automatically if your network supports this capability Otherwise you need to ask your network administrator for the appropriate IP settings Same IP section but cannot be 192 168 0 178 Obtain an IP address automatically Use the following IP address IP address 192 168 Subnet mask 255 2h5 255 0 Default gateway 192 358 0 Obtain DNS server address automatically Use the following DNS server addresses Preferred DNS server 202 96 134 133 Alternate DNS server 202 96 128 68 Validate settings upon exit Controlled by PC s in LAN MHD44TP can be connected with a r
20. d Ground 1 2 3rd Group 1 2 3rd Group 3 6 4th Group 7 8 4th Group 7 8 R 3 System Connection 3 1 Usage Precautions 1 System should be installed in a clean environment and has a prop temperature and humidity All of the power switches plugs sockets and power cords should be insulated and safety All devices should be connected before power on 2 lt 3 PTN Electronics Limited 5 www PTN electronics com HDBaseT Matrix Switcher 4x4 3 2 System Diagram i Laptop 7 c IR Receiver P P RS232 PTN control panel ZZ Laptop ONA TPHD402R IR Receiver Video Signal Audio Signal IR Signal TP Signal Control Signal 3 1 2 3 4 5 6 7 8 Projector 3 Connection Procedure Connect HDMI sources e g DVD to HDMI inputs of MHD44TP with HDMI cables Connect HDMI displayers e g HDTV to HDMI outputs of MHD44TP with HDMI cables Connect speakers earphones to AUDIO output ports 3p captive screw connectors Connect the HDBaseT port of HDBaseT receiver and MHD44TP with twisted pair Connect the RS232 port 9 pin female D of MHD44TP with control device e g PC Connect the RS232 port of controlled device to any other RS232 port 3p captive screw connector of MHD44TP The control signal can be transmitted bi directionally M
21. data bit is 8 stop bit is 1 and parity bit is none Communication protocol RS232 Communication Protocol Baud rate 9600 Data bit 8 Stop bit 1 Parity bit none Type Inquire the models information Lock Lock the front panel buttons on the Matrix Unlock Unlock the front panel buttons on the Matrix Nersion Inquire the version of firmware System iMessage Turn off the feedback command from the com port It Command will only show the Switch Ok MessageOn Turn on the feedback command from the com port Switch to the demo mode 1 gt 1 2 22 3 23 and Demo so on The switching interval is 2 seconds Undo To cancel the previous operation Transfer signals from the input channel x to all Operation output channels Command Transfer input signals to the corresponding output PTN2 0 channels respectively Command Switch off all the output channels System Transfer signals from the input channel to the output channel x PTN Electronics Limited 14 www PTN electronics com HDBaseT Matrix Switcher 4x4 PTN x Switch off the output channel x Transfer the AV signal from the input channel x1 to 1 2 the output channel x2 1 BIx2 Transfer the AV and IR signal from the input channel x1 to the output channel x2 Status Inquire the input channel to the ou
22. eceiver pass through to all the HDBaseT ports to control the remote devices HDMI HDMI input ports 4 in total type A female HDMI connector INPUTS connect with HDMI input source devices Connect with IR emitter to send out the IR signal from the HDBaseT port of the far end Receiver These IR OUTs make IROUT up an IR matrix with the IR INs on the HDBaseT receivers and all can be switched synchronously with the AV signal or separately switching IR IN Connect with IR receiver fixed IR input for the output cannot be switched separately It makes up an IR bi directional transmission with the IR OUT on the corresponding HDBaseT receiver HDMI HDMI output port connect with HDMI output devices To split HDMI output for local monitoring COAX HDMI de embedded digital audio output HDBaseT Works with receivers using HDBaseT technology such as TPHD402R TPHD402PR It can pass through AV IR and RS232 signal to 60m distance Meanwhile it can OUTPUTS PTN Electronics Limited 3 www PTN electronics com HDBaseT Matrix Switcher 4x4 provide power for the receivers which support POE RS232 RS232 port to communicate with the RS232 port on corresponding HDBaseT receiver When controlled by HDBaseT receiver the communication protocol must be the same with MHD44TP AUDIO HDMI de embedded stereo audio output The serial port for unit control 9 pin female connector
23. eck the connection status of the outputs 969973 Check the HDCP status of the inputs 969974 Check the HDCP status of the outputs 969975 Check the switching status 969976 Check the output resolution PTN Electronics Limited 16 www PTN electronics com HDBaseT Matrix Switcher 4x4 Set communication between PC and HDBaseT receiver D Yis for RS232 port connect with RS232 port of HDBaseT receiver Value 1 2 3 4 5 A B C D E F G or H The value of Y is defined into the following meanings in a given baud rate depended by the value of X Y 1 2 3 or 4 send this command to the corresponding HDBaseT receiver to control far end device b Y 5 send this command to all HDBaseT receivers to control all far end devices c Y A B CorD d Y E F Gor H For items c or d send this command it will be IH YV X saved to MHD44TP but taken without action to corresponding HDBaseT receiver And its command function will be effective almost at the same time when you send the command PWON for item c or PWOFF for item d Note A amp E are for port 1 B amp F are for port 2 C amp G are for port 3 D amp H are for port 4 2 Xis for bound rate Value ranges from 1 to 7 1 is for 2400 2 for 4800 3 for 9600 4 for 19200 5 for 38400 6 for 57600 and 7 for 115200 3 is for data max 48 Byte 4 The symbol is the end of one command If there are some symbols of
24. er the IR signal to IR OUT port 3 IR Settings When need to control a remote displayer from local the IR receiver used must be with IR carrier The IR signal is transferred to the corresponding zone connected with the HDBaseT receiver which is connected with the IR emitter When the IR receiver is connected to IR ALL IN port the IR signal can be finally transferred to all the 4 IR emitters connected with HDBaseT receivers As the figure below PTN Electronics Limited 12 www PTN electronics com IR Remote 4 es IR Receiver TP Signal IR Signal Video Signal ZONE cy ZONE ZONE LM IREYE JO OJO COAX COAX 85232 XN eb TPHD402R LJ ee TPIN HDMIJOUT IRIN IRQUT RS232 e e e Control Remote Displayer from Local HDBaseT Matrix Switcher 4x4 4 Controlled by Third party IR Control Device Use the included IR converting cable see as below connect the red end to IR input port of MHD44TP the black end to IR output port of the third party control device Then the IR signal is able to be transmitted via the twisted pair and finally gets to remote output device 1000mm Connect to signal GND Connect to signal 5 3 RS232 Control 5 3 1 RS232 Commands Through the RS232 communication port user can control a far end device whose bound rate is 2400 4800 9600 19200 38400 57600 or 115200 Default setting of MHDAATP bound rate is 9600
25. ics com www PTN electronics com Email info PTN electronics com PTN Electronics Limited Tel 86 755 2846 1819 Fax 486 755 8471 7796 Website www PTN electronics com 21013062 1806013
26. ignal from IR OUT port synchronously by the switcher Note The IR OUT port number is corresponding with HDMI INPUTS port number as default Example To transfer both AV and IR signals from input channel No 1 to output channel No 3 Operation Press buttons in this order 1 AV 3 Fun ti n gt ALL outputs button To transfer one input to all outputs Example To transfer both AV and IR signals from input buttons channel No 1 to all output channels Operation Press buttons in this order 1 ALL gt EDID management button manually capture and copy the EDID data from output device to input port Example To capture and copy the EDID data from output channel No 4 to input channel No 2 Operation Press buttons in this order EDID 2 4 Press button 2 in INPUTS area 4 in OUTPUTS area OUTPUTS Output buttons ranging from 1 to 4 PTN Electronics Limited 2 www PTN electronics com HDBaseT Matrix Switcher 4x4 With the front control panel the switcher could be control directly and rapidly by pressing the buttons under below format Input Channel AV Output Channel Input Channel Fill with the number of input channel to be controlled Output Channel Fill with the number of output channels to be controlled 2 2 Rear Panel TCP IP m No Name Description G IRALLIN IR control signal input port connect with IR r
27. in one command this case is allowed and the last one is the end Note 1 Please disconnect all the twisted pairs before sending command EDIDUpgrade X 2 In above commands are symbols for easy reading and do not need to be typed in actual operation 3 Please remember to end the commands with the ending symbols and 4 Type the command carefully it is case sensitive PTN Electronics Limited 17 www PTN electronics com HDBaseT Matrix Switcher 4x4 5 3 2 Control MHD44TP To control MHD44TP you need to connect the 9 pin female RS232 port to PC s RS232 port or you can just connect any one of the HDBaseT receiver s RS232 port with PC RS232 command transmits to MHD44TP via the twisted pair By using RS232 control software and setting right baud rate you are able to control MHD44TP then 5 3 3 Control 3rd Party Device from Local Connect the 9 pin female RS232 port of MHD44TP with PC by using the RS232 command Y X you are able to control the 3rd party device connected with the HDBaseT receiver Please reference to the detailed command description in 5 3 1 RS232 Commands j em PC SOAU TAUTAS E of lo E D n E LCS I LE TPHD402R 230 4 party SC Control 3rd party Device from Local 5 3 4 Bi directional RS232 Control By connecting one 3p captive screw RS232 port of MHD44TP with PC or
28. ou can enter the configuration page to configure the IP port including the IP reset Serial reset and password reset etc As picture below PTN Electronics Limited 20 www PTN electronics com HDBaseT Matrix Switcher 4x4 6 1 Configuration Windows Internet Explor C hitp192 168 0 178 L0GIN 8 x sing j m 2 bing B he 5 sen di Favorites y Suggested Sites v gp Web Slice Gallery v Port Configuration OS ov Pager Tools amp IPort Configuration Web Server E welcome systom into serial into change password reset restore defaut Welcome to IPort Web Server Internet Protected Mode Off f gt 105 v Step5 Change IP Serial Port Change IP a Select the tab system info and then you are able to change the IP Network Parameters DO NOT change it Device IP Mode Gtatic v IP 192 6 1 Gateway SubMar 255 255 255 DNS Server Enter into right IP for each item better has the same IP section with the router Device Parameters Command 5000 Web 80 IP Eilter DO NOT change it Filter1 IP SubMark Filter2 IP SubMark Filter3 IP SubMark Filter4 IP SubMark Filter IP SubMark Filter6 IP SubMark Filter7 IP SubMark Filter8 IP SubMark
29. outer to make up a LAN with the PC s this make it able to be controlled in a LAN When control just make sure MHD44TP s IP section is the same with the router Please connect as the following figure for LAN control PTN Electronics Limited 19 www PTN electronics com HDBaseT Matrix Switcher 4x4 Step1 Step2 Step3 Step4 Step5 Connect the TCP IP port of MHD44TP to Ethernet port of PC with twisted pair Set the PC s IP address and gateway to the same IP section as MHD44TP Do please remember the PC s original IP address and gateway Set MHD44TP s IP address and gateway to the same IP section as the router Set the PC s IP address and gateway as the original one Connect MHD44TP and PC s to the router In the same LAN each PC is able to control MHD44TP asynchronously 5 4 2 TCP IP Settings Step1 Step2 Step3 Step4 Connect the TCP IP port of MHD44TP to Ethernet port of PC with twisted pair Set the PC s IP and gateway to the same IP section as the default IP of MHD44TP 192 168 0 178 Enter the 192 168 0 178 to the Internet Explore you will see the LOGIN page as below Com M gum E sos s Favorites ig Suggested Sites ge Web Slice Gallery Port Configuration Password Login Please input the password Internet Protected Mode Off Enter the password 88888 and you can only press the Login button not the Enter key on your keyboard Then y
30. tput channels one by one Save X Save the present operation to the preset command X ranges from 0 to 9 Recall Y Recall the preset command Y Clear Y Clear the preset command Y PWON Work in normal mode PWOFF Enter into standby mode 17 HDCP management command Y is for input value 1 or output value X is the number of one port if the value of X is ALL it means all ports 7 is for working status value 1 or 0 gt amp Z 1 means the input port is compliant with HDCP gt Y O amp Z 1 means output with HDCP gt amp Z 0 means the input port is not compliant with HDCP gt Y O amp Z 0 means output without HDCP 1 R x2 Transfer the IR signal from the input channel x1 to the output channel x2 EDIDH xJBIy Copy the EDID from output port x to input port y If the EDID data is effective and the audio part supports not only PCM mode then force set it to PCM mode If the EDID data is not effective then set it as initialized EDID data Enable HDMI audio output of port x oo X 1 2 3 4 enable this one port X 5 enable all the 4 ports MAn Disable audio output of port x X 1 2 3 4 disable this one port 5 disable all the 4 ports EDIDG 4 Get EDID data from the output and display the output port number of X EDIDMInit Recover the factory default EDID data
Download Pdf Manuals
Related Search
MHD44TP mhd45pk15-k mhd45ppk25-db25p-k mhd45ppk-9-bk mhd45pk15-db15p-k mhd45pk9-db9p-k mhd45pk9-db9s-k mhd45pk15-db15pk mhdtpk9-db9s-k mhdtpk9-k mhd 4 poprad mhd45ppk-15-bk mhdtppk25-db25p-k mhdtppk9-db9s-k mhdtpk9-db9p-k