eq manual all(2012.04.14)
Contents
1. ACUS 4TN PREAMP USER S MANUAL Functions 3 Tuner Button for Power on off Button 4 B a n d E Q wi t h F N D Tu n e r The tuner will work with or without a cable plugged into the output jack 4 Volume Knob The VOLUME controls the output volume Turned fully counter clockwise it is completely OFF Turned fully clockwise it is LOUD 5 Bass EQ TONE CONTROL for bass tones 6 Treble EQ TONE CONTROL for high tones The BASS and TREBLE controls are a 2 band equalizer for controlling tone The BASS and TREBLE tone controls are normal boost cut shelving controls The center detent on these tone controls yields a flat tone response 12 boosts the tone 12 cuts the tone O grat max VOLUME min 4 boost BASS cut Battery 5 A 9 volt battery powers the ATN 3000 preamp Before connecting the bI gt Od instrument to an amplifier or mixer please check that a fully charged 9 volt boost TREBLE cut battery is connected TUNER ALNE ae TAA Tuner FND Display Tuner LED Display Tuner Button Volume Bass Treble OA AOUOUN gt aS e Tuner Operation Specification Features 4Band EQ with FND Tuner 4 Input Impedance 20MQ Output Impedance 1KQ Tuner FND Display A Control Range Bass2. 12dB at 80Hz Middle 12dB at 800Hz Tuner LED Display b gt O lt 1 Treble 12dB at 3KHz Presence 12dB at 15KHz Tuner LED Display Tuner Function Auto Chromatic Tuning Tuning Guide LED for right tune Battery Life Pre amp only a _ Tuning Guide LED for flat tune Tuner off 700Hours 0 7mA Tuner on with signal 40Hours 12mA Bw Tuning Guide LED for Sharp tune Power Supply 9V Alkaline Battery Low Battery Check LED Pick up OMEGA II Piezo Cable pick up Dimension W 72mm X D 50mm Tuner Display 2 8 X 1 9 The tuner will work with or without a cable plugged into the output jack Pushing the tuner button turns ON the tuner When the tuner is active 2 the output signal is muted No sound will go to the amplifier or mixer Caution when the tuner is active The jack should be pluged for proper Preamp working Pushing the tuner button again turns the tuner OFF and the output TUNER will works regardless pluging jack signal will be active and sound will go to the amplifier There is no output sound please check if tuner or mute is turned on When LCD screen is dim or no display please check battery life If the tuner is ON and the tuner button is not pushed within 2 minutes To prevent battery loss please unplug jack when preamp is not in use the tuner will turn OFF automatically and sound returned to the output Do not disassemble for repair Return to your dealer for service
3. e or distortion please exchange battery Check if the pickup and battery connector is connected correctly or not Check if out put jack is connected correctly 2 When there is hum noise Check the pickup is connected well or not Check if the connectors are connected to correct position well or not 3 Some causes of the balance problem When the bottom of saddle or the groove of saddle is not flat When saddle is installed to the groove of saddle loosly When the connection is not good between the bottom of saddle and the groove of saddle When Saddle is very short When there is grounds on the groove of saddle When Saddle is declined toward front or back When the top of guitar is bended When the pickup is installed to only a part of the groove of saddle back page
4. or repair The tuner Note Readout FND Display shows the nearest note of one Do not use too much force when operating the control plucked string s sound The Note Read Display read out shows twelve note possibilities in half steps in sharps for example A A B C C D D and so on For flat notes for example Bb B flat use A For Gcleal Eb E flat use D BELCAT Co Ltd Tel 86 752 355 7545 Fax 86 752 355 2460 RoHS C Email belcat belcat com This product complies Internet www belcat com with the RoHS directive INSTALLATION MANUAL 1 Contents O 2 Battery 3 Pick Up Box oA Im oh 1 Preamp 4 Output Jack g 6 Screw 2 Tool 4 Router and Grinder cutting edge 3mm 1 Electric Drill fs me o 2 Drill Bit 5 Round File 2 3mm or 3mm O 3 Phillips Screwdriver 6 Masking Tape 1 Cut out the hole with template Cutting Template Masking Tape Cutting Template 3 Drilling hole for Jack 4 Drilling hole for pick up Masking 5 Insert EQ and battery box into hole of guitar 6 Fasten screws properly 5 Put plugs into jacks 7 Installing the pick up 8 Fix wire with clip EQ peal Clip Out put jack LIN x Cable i Battery box Solution 1 When there is no sound or sound is stopped Check guitar cable amp or Mixer Check if there is batter or not When it happens nois
Download Pdf Manuals
Related Search