kenwood TK-2160/3160 User Manual
Contents
1. 11 PROGRAMMABLE AUXILIARY FUNCTIONS 14 OPERATING BASICS 15 SWITCHING POWER ON OFF 15 ADJUSTING THE VOLUME 15 SELECTING A CHANNEL 15 MAKING A CALL 16 RECEIVING A CALL 16 SCAN 17 PRIORITY SCAN 17 CHANNEL LOCKOUT 18 REVERT CHANNEL 18 5 TONE SIGNALLING 19 RECEIVING 19 TRANSMITTING 19 iv DTMF SIGNALLING 20 FleetSync OPERATION 21 CALL TYPES 21 QUIET TALK QT DIGITAL QUIET TALK DQT 22 SCRAMBLER 23 VOX OPERATION 24 EMERGENCY CALLS 26 ADVANCED OPERATIONS 27 SELECTING AN OUTPUT POWER 27 MONITO2. 21 FleetSync OPERATION FleetSync is a protocol owned by KENWOOD Corporation and is enabled or disabled by your dealer This function opens the squelch only when the transceiver receives the Fleet code and ID code programmed in your transceiver Calls that do not contain the correct codes will not be heard RECEIVING When you receive a signal containing both your Fleet code and your ID code squelch opens and you will hear the call An alert tone will sound The LED indicator flashes orange To mute the speaker after squelch opens press the key programmed as Monitor Momentary or Monitor Toggle TRANSMITTING To transmit a FleetSync signal simply press the PTT switch and make the call If the selected channel has been programmed with a FleetSync PTT ID it will be transmitted when the call is made 22 QUIET TALK QT DIGITAL QUIET TALK DQT Your dealer may have programmed QT or DQT signalling on your transceiver channels A QT tone DQT code is a sub audible tone code which allows you to ignore not hear calls from other parties who are using the same channel When a channel is set up with a QT tone or DQT code squelch will only open when a call containing a matching tone or code is received Likewise signals that you transmit will only be heard by parties whose QT DQT signalling matches your transceiver If a call containing a different tone or code is made on the same channel you are using squelch will no
3. Transpond for 5 Tone Signalling is programmed an acknowledgment signal is returned to the calling station If Tone Alert for 5 Tone Signalling is programmed an alert tone will sound when the correct tones are received TRANSMITTING To transmit a 5 Tone signal simply press the PTT switch and make the call If the selected channel has been programmed with a 5 Tone signal it will be transmitted when the call is made 20 DTMF SIGNALLING DTMF Signalling is either enabled or disabled by your dealer This function opens the squelch only when the transceiver receives the DTMF code 3 to 10 digits programmed in your transceiver Each transceiver is normally programmed with a unique code You will not hear calls from transceivers that are not programmed with a matching code Your dealer may also program a Group Code in your transceiver Ask your dealer for further details When you receive a signal containing the correct tones squelch opens and you will hear the call The LED indicator flashes orange To mute the speaker after squelch opens press the key programmed as Monitor Momentary or Monitor Toggle Your dealer can program the squelch to close again after a specific time period elapses If Transpond for DTMF Signalling is programmed an acknowledgment signal is returned to the calling station If Tone Alert for DTMF Signalling is programmed an alert tone will sound when the correct tones are received
4. amount of current may flow upon discharging The battery may generate heat or smoke rupture or burst into flame Do not reverse charge or reverse connect the battery The battery pack has positive and negative poles If the battery pack does not smoothly connect with a charger or operating equipment do not force it check the polarity of the battery If the battery pack is reverse connected to the charger it will be reverse charged and an abnormal chemical reaction may occur The battery may generate heat or smoke rupture or burst into flame Do not touch a ruptured and leaking battery If the electrolyte liquid from the battery gets into your eyes wash your eyes out with fresh water as soon as possible without rubbing your eyes Go to the hospital immediately If left untreated it may cause eye problems 5 Do not charge the battery for longer than the specified time If the battery pack has not finished charging even after the regulated time has passed stop it The battery may generate heat or smoke rupture or burst into flame Do not place the battery pack into a microwave or high pressure container The battery may generate heat or smoke rupture or burst into flame Keep ruptured and leaking battery packs away from fire If the battery pack is leaking or the battery emits a bad odor immediately remove it from flammable areas Electrolyte leaking from battery can easily catch on fire and may cause th
5. do not damage the release latch Before charging a battery pack that is attached to the transceiver ensure that the safety catch is firmly closed While operating the transceiver using a Li ion or Ni MH battery pack in areas with an ambient temperature of 10 C 14 F and lower operating time may be shortened 8 INSTALLING REMOVING ALKALINE BATTERIES Do not install batteries in a hazardous environment where sparks could cause an explosion Never discard old batteries in fire extremely high temperatures can cause batteries to explode Do not short circuit the battery case terminals Do not use commercially available rechargeable batteries Note If you do not plan to use the transceiver for a long period remove the batteries from the battery case This battery case has been designed for transmitting at a power of approximately 1 W the low power setting on your transceiver If you want to transmit a stronger signal using the high power setting on your transceiver use an optional rechargeable battery pack 1 To open the battery case press on the 2 tabs on the upper rear of the case then pull the 2 halves apart 2 Insert 6 AA LR 6 alkaline batteries into the battery case Be sure to match the polarities with those marked in the bottom of the battery case 3 Align the tabs of the cover with the base then push down on the cover until it locks in place 9 Scre
6. locking bracket you must remove the battery pack from the rear of the transceiver 1 Insert the speaker microphone plugs into the speaker microphone jacks 2 Attach the locking bracket using the supplied screw Note To lift the locking bracket after it has been installed use a piece of hardened plastic or metal such as a small screwdriver Lift the bracket by its tab beside the screwhole taking care not to damage the bracket 11 4 1 2 3 5 8 6 7 GETTING ACQUAINTED Antenna Microphone Speaker 12 q q q q q LED indicator w w w w w Channel Switch Rotate to select a channel from 1 to 16 r olo C D E L tiL yls u o u nitn o C g nih s alF d e R g nitti m s n a rt elih W w ol r e w o p y r e tt a B n e e r G g nivie c e r elih W g nin n a c s elih W e g n a r O g nir o tin o m elih W s r e vie c s n a rt n o e n o T 5 r o f p u t e s yln o g nilla n gi S e h t g nits e t n e h W nia G X O V le v el ytivitis n e s d n o c e s 1 n a g nivie c e r elih W t a h t lla c d e d o c n e e d o c e h t s e h ct a m r u o y ni p u t e s r e vie c s n a rt s d n o c e s 2 o t u A e h t r e tf A e h t f o r e m i T t e s e R lla c e n o T 5 s a h t
7. or wire Do not carry or store the battery pack in containers holding metal objects such as wires chain necklace or hairpins If the battery pack is short circuited excessive current will flow and the battery may generate heat or smoke rupture or burst into flame It will also cause metal objects to heat up DANGER 3 Do not incinerate or apply heat to the battery If the insulator is melted the gas release vent or safety function is damaged or the electrolyte is ignited the battery may generate heat or smoke rupture or burst into flame Do not use or leave the battery near fires stoves or other heat generators areas reaching over 80 C 176 F If the polymer separator is melted due to high temperature an internal short circuit may occur in the individual cells and the battery may generate heat or smoke rupture or burst into flame Do not immerse the battery in water or get it wet by other means If the battery s protection circuit is damaged the battery may charge at extreme current or voltage and an abnormal chemical reaction may occur The battery may generate heat or smoke rupture or burst into flame Do not charge the battery near fires or under direct sunlight If the battery s protection circuit is damaged the battery may charge at extreme current or voltage and an abnormal chemical reaction may occur The battery may generate heat or smoke rupture or burst into flame Use only
8. 3 5 3 N 1 la u n a m n oitc u rts n I X X 8 8 7 1 2 6 B 1 2 PREPARATION BATTERY PACK PRECAUTIONS Do not recharge the battery pack if it is already fully charged Doing so may cause the life of the battery pack to shorten or the battery pack may be damaged After recharging the battery pack disconnect it from the charger If the charger power is reset turned ON after being turned OFF recharging will start again and the battery pack will become overcharged Do not use the transceiver while charging the battery pack We recommend you switch the transceiver power OFF while charging is taking place Do not short the battery terminals or dispose of the battery by fire Never attempt to remove the casing from the battery pack Information concerning the optional Li ion battery pack The battery pack includes flammable objects such as organic solvent Mishandling may cause the battery to rupture producing flames or extreme heat deteriorate or cause other forms of damage to the battery Please observe the following prohibitive matters Do not disassemble or reconstruct battery The battery pack has a safety function and protection circuit to avoid danger If they suffer serious damage the battery may generate heat or smoke rupture or burst into flame Do not short circuit the battery Do not join the and terminals using any form of metal such as a paper clip
9. INSTRUCTION MANUAL MODE D EMPLOI MANUAL DE INSTRUCCIONES MANUALE DI ISTRUZIONI BEDIENUNGSANLEITUNG GEBRUIKSAANWIJZING B62 1788 00 E E3 09 08 07 06 05 04 03 02 01 00 TK 2160 TK 3160 VHF FM TRANSCEIVER UHF FM TRANSCEIVER METTEUR R CEPTEUR FM VHF METTEUR R CEPTEUR FM UHF TRANSCEPTOR DE FM VHF TRANSCEPTOR DE FM UHF RICETRASMETTITORE FM VHF RICETRASMETTITORE FM UHF VHF FM TRANSCEIVER UHF FM TRANSCEIVER VHF FM ZENDONTVANGER UHF FM ZENDONTVANGER TK 2160 TK 3160 VHF FM TRANSCEIVER UHF FM TRANSCEIVER INSTRUCTION MANUAL i EXPLOSIVE ATMOSPHERES GASES DUST FUMES etc Turn off your transceiver while taking on fuel or while parked in gasoline service stations Government law prohibits the operation of unlicensed radio transmitters within the territories under government control Illegal operation is punishable by fine or imprisonment or both Refer service to qualified technicians only Safety It is important that the operator is aware of and understands hazards common to the operation of any transceiver THANK YOU We are grateful you chose KENWOOD for your land mobile radio applications We believe this easy to use transceiver will provide dependable communications to keep personnel operating at peak efficiency KENWOOD transceivers incorporate the latest in advanced technology As a result we feel strongly that you will be pleased with the quality and features of t
10. OX operation allows you to transmit hands free This feature can only be used if you are using a supported headset When operating VOX you must set a VOX Gain level This setting allows the transceiver to recognize sound levels If the microphone is too sensitive it will begin transmitting when there is noise in the background If it is not sensitive enough it will not pick up your voice when you begin speaking Be sure to adjust the VOX Gain level to an appropriate sensitivity to allow smooth transmission To activate VOX and set the VOX Gain level perform the following steps 1 Connect the headset to the transceiver The VOX function does not activate when a headset is not connected to the accessory terminal of the transceiver 2 With the transceiver power OFF press and hold the Side 1 key for 2 seconds while turning the transceiver power ON The LED flashes red and green 3 Press the Side 1 key to increase the VOX Gain level and the Side 2 key to decrease the level The VOX Gain can be adjusted from levels 1 to 10 and OFF 4 While adjusting the gain level speak into the headset microphone as you would while under normal operation to test the sensitivity level When the microphone recognizes a sound the LED lights orange This allows you to determine a suitable level where background noise will not activate VOX operation while speaking into the microphone will The transceiver does not transmit your voice duri
11. R SQUELCH OFF 27 BACKGROUND OPERATIONS 28 TIME OUT TIMER TOT 28 BATTERY SAVE 28 LOW BATTERY WARNING 29 BUSY CHANNEL LOCKOUT BCL 29 STUN 29 BEGINNING END OF TRANSMISSION TX SIGNAL 29 CONTENTS CONTINUED 1 UNPACKING AND CHECKING EQUIPMENT Note The following unpacking instructions are for use by your KENWOOD dealer an authorized KENWOOD service facility or the factory Carefully unpack the transceiver We recommend that you identify the items listed in the following table before discarding the packing material If any items are missing or have been damaged during shipment file a claim with the carrier immediately SUPPLIED ACCESSORIES Belt clip Speaker microphone jacks cap Binding machine screw Speaker microphone locking bracket m etI r e b m u n tr a P ytitn a u Q pilc tle B X X 1 0 7 0 9 2 J 1 g nik c ol e n o h p o r ci m r e k a e p S t e k c a r b X X 4 6 4 8 1 2 J 1 p a c s k c aj e n o h p o r ci m r e k a e p S X X 6 7 6 0 9 0 B 1 w e r c s e nih c a m g nid ni B X X 4 0 0
12. RY FUNCTIONS The AUX Side 1 and Side 2 keys can be programmed with the auxiliary functions listed below Call1 1 Call2 1 Emergency 2 Monitor Momentary Monitor Toggle None RF Power Low Scan Scan Temporary Delete Scrambler Squelch Off Momentary Squelch Off Toggle 1 These functions are only available on transceivers set up for 5 Tone signalling 2 This function can be programmed only on the AUX key 15 OPERATING BASICS SWITCHING POWER ON OFF Turn the Power switch Volume control clockwise to switch the transceiver ON Turn the Power switch Volume control counterclockwise to switch the transceiver OFF ADJUSTING THE VOLUME Rotate the Power switch Volume control to adjust the volume Clockwise increases the volume and counterclockwise decreases it You may need to adjust the volume more precisely while communicating with other parties Note If your dealer programmed Squelch Off Momentary or Squelch Off Toggle onto a PF key you can press that key to hear background noise while adjusting the volume level refer to MONITOR on page 27 SELECTING A CHANNEL Rotate the Channel switch to choose your desired channel from 1 to 16 Clockwise increases the number and counterclockwise decreases it If a channel has not been programmed it cannot be used When a non programmed channel is selected the LED indicator flashes red and orange and
13. The last channel responded to is assigned as the new revert channel Selected The last channel selected is assigned as the new revert channel Selected Talkback If the channel has been changed during Scan the newly selected channel is assigned as the new revert channel However the transceiver also transmits on the channel where Scan is currently paused Priority If your dealer has programmed a Priority channel it is the revert channel Priority Talkback If your dealer has programmed a Priority channel it is the revert channel However the transceiver also transmits on the channel where Scan is currently paused 19 5 TONE SIGNALLING 5 Tone Signalling is enabled or disabled by your dealer This function opens the squelch only when the transceiver receives the 5 tones programmed in your transceiver in succession Transceivers that do not transmit the correct tones will not be heard Your dealer may also activate Group Call for your transceiver RECEIVING When you receive a signal containing the correct tones squelch opens and you will hear the call The LED indicator flashes orange The LED remains lit after pressing any key To mute the speaker after squelch opens press the key programmed as Monitor Momentary or Monitor Toggle Your dealer can program the squelch to close again after a specific time period elapses The LED indicator flashes orange 2 seconds at this time If
14. again If the Emergency mode completes the preset number of cycles Emergency mode will automatically end and the transceiver will return to the channel that was in use before Emergency mode was entered Note Your dealer can set the transceiver to emit tones and received signals as normal or mute the speaker during Emergency operation 27 ADVANCED OPERATIONS SELECTING AN OUTPUT POWER Each channel is programmed with either high or low output power by your dealer You can change the output power of only channels programmed as high When you can reliably communicate with other parties without using high power select low power by pressing the key programmed as RF Power Low Each time you press RF Power Low the output power toggles between high and low Using low power conserves battery power and reduces the risk of interfering with other communications Note Pressing RF Power Low while using a channel programmed with low power causes an error tone to sound When changing a channel from high power to low power all channels programmed with high power are changed to low MONITOR SQUELCH OFF You can use the Monitor Squelch Off key to listen to weak signals that you cannot hear during normal operation and to adjust the volume when no signals are present on your selected channel Your dealer can program a key with one of 4 functions Squelch Off Momentary Press and hold to hear background noise Release t
15. an alert tone sounds 16 MAKING A CALL 1 Make sure no parties are currently transmitting on your selected channel 2 Press the PTT switch and speak into the microphone in your normal speaking voice For best sound quality at the receiving station hold the microphone approximately 1 5 inches 3 4 cm from your mouth 3 Release the PTT switch to receive RECEIVING A CALL Your dealer may have programmed QT or DQT signalling on your transceiver If your selected channel is programmed with one of these features you will hear calls only when another party in your system makes a call All other calls will not be heard If your selected channel is not set up with QT or DQT you will hear calls made by any party not just those in your system 17 SCAN Scan is useful for monitoring signals on the transceiver channels When scanning the transceiver checks for a signal on each channel and only stops if a signal is present The transceiver will remain on a busy channel until the signal is no longer present Your dealer programs the delay time between signal drop out and Scan resumption If a signal is received during the delay time the transceiver will remain on the same channel Note You can only use Scan if your dealer has programmed at least 2 channels on the transceiver Also there must be at least 2 channels not locked out of Scan Ask your dealer for an explanation on how Channel Scan functions when usi
16. e battery to generate smoke or burst into flame Do not use an abnormal battery If the battery pack emits a bad odor appears to have different coloring is deformed or seems abnormal for any other reason remove it from the charger or operating equipment and do not use it The battery may generate heat or smoke rupture or burst into flame Using the Li ion Battery Pack Charge the battery pack before using it To keep the battery discharge at a minimum remove the battery pack from the equipment when it is not in use Store the battery pack in a cool and dry location When storing the battery pack for a long period 1 Remove the battery pack from the equipment 2 Discharge the battery pack if possible 3 Store the battery pack in a cool below 25 C 77 F and dry location 6 Characteristics of the Li ion Battery Pack As the battery pack is charged and discharged repeatedly the battery capacity decreases Even if the battery pack is unused the battery pack degrades It takes a longer time to charge the battery pack in cooler areas The life of battery pack is shortened when it is charged and discharged in hotter areas When the battery pack is stored in a hot location the battery pack degrades quicker Do not leave the battery pack in vehicles or near heating appliances When the battery pack operating time becomes short even if it is fully charged replace the batte
17. f both are set the ID signal is transmitted when you press and release the PTT switch
18. he key to return to normal operation Squelch Off Toggle Momentarily press to hear background noise Press the key again to return to normal operation Monitor Momentary Press and hold to deactivate QT DQT or 5 Tone Signalling Release the key to return to normal operation Monitor Toggle Momentarily press to deactivate QT DQT or 5 Tone Signalling Press the key again to return to normal operation 28 BACKGROUND OPERATIONS Your dealer can activate a variety of transceiver functions to perform without any additional operation on your part TIME OUT TIMER TOT The Time out Timer is used to prevent any caller from using a channel for an extended period of time If you continuously transmit for a period of time that exceeds the programmed time default 60 seconds the transceiver will stop transmitting and an alert tone will sound To stop the tone release the PTT switch If programmed by your dealer a pre alert tone will sound before the timer expires Also if programmed by your dealer you may have to wait for a short duration before you can continue to transmit If you press the PTT switch before the timer has been reset an alert tone will sound and the transceiver will not enter transmit mode BATTERY SAVE The Battery Save function decreases the amount of power used when a signal is not being received and no operations are being performed no keys are being pressed and no switches are being turned Whi
19. his product MODELS COVERED BY THIS MANUAL TK 2160 VHF FM Transceiver TK 3160 UHF FM Transceiver NOTICES TO THE USER ii PRECAUTIONS Observe the following precautions to prevent fire personal injury and transceiver damage Do not modify this transceiver for any reason Do not expose the transceiver to long periods of direct sunlight nor place it close to heating appliances Do not place the transceiver in excessively dusty humid and or wet areas nor on unstable surfaces If an abnormal odor or smoke is detected coming from the transceiver switch OFF the power immediately and remove the optional battery pack from the transceiver Contact your KENWOOD dealer iii CONTENTS UNPACKING AND CHECKING EQUIPMENT 1 SUPPLIED ACCESSORIES 1 PREPARATION 2 BATTERY PACK PRECAUTIONS 2 INSTALLING REMOVING THE OPTIONAL RECHARGEABLE BATTERY PACK OR ALKALINE BATTERY CASE 7 INSTALLING REMOVING ALKALINE BATTERIES 8 INSTALLING THE OPTIONAL ANTENNA 9 INSTALLING THE BELT CLIP 9 INSTALLING THE COVER OVER THE SPEAKER MICROPHONE JACKS 10 INSTALLING THE OPTIONAL SPEAKER MICROPHONE 10 GETTING ACQUAINTED
20. i fi s e t a vitc a y b d e t a vitc a n e e b r ela e d r u o y e g n a r O d e R d e tc ele s e h T t o n s a h le n n a h c d e m m a r g o r p n e e b e b t o n n a c d n a d e s u e g n a r O n e e r G e h t g nis s e r p elih W T T P n e h w h cti w s d e t a vitc a si n u ts n e e r G d e R si r e vie c s n a rt e h T nia G X O V ni e d o m t n e m ts ujd a 13 e e e e e Power switch Volume control Turn clockwise to switch ON the transceiver Rotate to adjust the volume To switch OFF the transceiver turn counterclockwise fully r r r r r AUX key This is a PF Programmable Function key Press it to activate its auxiliary function page 14 The default setting for this key is None t t t t t PTT Push to Talk switch Press this switch then speak into the microphone to call a station y y y y y Side 1 key This is a PF Programmable Function key Press it to activate its auxiliary function page 14 The default setting for this key is Call1 u u u u u Side 2 key This is a PF Programmable Function key Press it to activate its auxiliary function page 14 The default setting for this key is Monitor Toggle i i i i i Speaker Microphone jacks Connect an optional speaker microphone here 14 PROGRAMMABLE AUXILIA
21. le the channel is not busy and no operation is performed for 10 seconds Battery Save activates When a signal is received or an operation is performed Battery Save is disabled 29 LOW BATTERY WARNING Low Battery Warning alerts you when the battery needs to be recharged or replaced While transmitting or receiving the LED will blink red when the battery power is low If programmed by your dealer a tone may also sound BUSY CHANNEL LOCKOUT BCL When activated BCL prevents you from interfering with other parties who may be using the same channel that you selected Pressing the PTT switch while the channel is in use will cause your transceiver to emit an alert tone and transmission will be inhibited you cannot transmit Release the PTT switch to stop the tone and return to receive mode STUN When the transceiver receives a call containing a stun code either transmit mode will be disabled or both receive mode and transmit mode will be disabled default This function is used when a transceiver is stolen or lost Stun is cancelled when the transceiver receives a call with a revive code BEGINNING END OF TRANSMISSION TX SIGNAL The Beginning of TX and End of TX identification signals are used to access and release some repeaters and telephone systems If Beginning of TX is set the ID signal is transmitted when you press the PTT switch If End of TX is set the ID signal is transmitted when you release the PTT switch I
22. ng 5 Tone or DTMF signalling To start scanning press the key programmed as Scan Scanning starts from the current channel and ascends through the channel numbers The LED flashes green When a signal is received on a channel and signalling matches the LED indicator lights green To end Scan press the Scan key again PRIORITY SCAN If your dealer set up a Priority channel on your transceiver the transceiver will automatically change to the Priority channel when a call is received on it even if a call is being received on a regular channel The transceiver will remain on the Priority channel until the signal drops out Your dealer programs the delay time between signal drop out and Scan resumption 18 TEMPORARY CHANNEL LOCKOUT During Scan if a key is programmed with the Scan Temporary Delete function you can temporarily remove specific channels from the scanning sequence When Scan stops at a channel you can remove that channel from the scanning sequence by pressing the Scan Temporary Delete key To add the channel back into the Scan list simply exit Scan mode or switch the transceiver OFF and then ON again REVERT CHANNEL During Scan pressing the PTT switch to transmit will cause the transceiver to select the revert channel Your dealer can program the revert channel using one of the following methods Last Called The last channel received is assigned as the new revert channel Last Used
23. ng this test procedure 25 5 Turn the transceiver power OFF and then ON again to save the setting and activate VOX To turn VOX operation OFF enter the VOX Gain level setting step 2 above and press the PTT switch then turn the transceiver power OFF and then ON again Note If a speaker microphone is connected to the transceiver while the VOX function is switched ON and the VOX Gain Level is configured to a higher more sensitive level louder received signals may cause the transceiver to start transmission When you operate the VOX function you must use an optional KHS 1 or KHS 2 accessory 26 EMERGENCY CALLS If your transceiver has been programmed with the Emergency function you can make emergency calls Note Only the AUX key can be programmed with the Emergency function 1 Press and hold the key programmed as Emergency Depending on the delay time programmed into your transceiver the length of time you must hold the Emergency key will vary When the transceiver enters Emergency mode a tone will sound and the transceiver will change to the emergency channel and begin transmitting based on how the transceiver is set up by your dealer When transmission ends a second tone will sound The transceiver will henceforth periodically transmit with tones sounding when it starts and stops Transmission periods are set by your dealer 2 To exit Emergency mode press and hold the Emergency key
24. ry pack Continuing to charge and discharge the battery pack may result in electrolyte leakage Charging the Li ion Battery Pack When charging a transceiver with a KNB 24L battery pack the safety catch of the battery pack may stick out past the battery When inserting the transceiver with the battery pack into the charger the safety catch will touch the metal contacts of the charger and the charger LED will momentarily light red Be sure to push the transceiver fully into the battery pack slot so the safety catch no longer touches the charger terminals Once in place the battery pack will begin charging For charging procedures refer to the KSC 25 Instruction Manual 7 INSTALLING REMOVING THE OPTIONAL RECHARGEABLE BATTERY PACK OR ALKALINE BATTERY CASE 1 Match the guides of the battery pack with the corresponding grooves on the upper rear of the transceiver then firmly press the battery pack to lock it in place 2 Flip the safety catch into place to prevent accidentally pressing the release latch and removing the battery 3 To remove the battery pack lift the safety catch press the release latch then pull the battery pack away from the transceiver Note To lift the battery pack safety catch use a piece of hardened plastic or metal such as a screwdriver that is no more than 6 mm wide and 1 mm thick It is imperative that you place the implement under only the lip of the safety catch so that you
25. t open and you will not hear the call This allows you to ignore not hear these calls Although it may seem like you have your own private channel while using QT DQT other parties can still hear your calls if they set up their transceiver with the same tone or code 23 SCRAMBLER Whereas the Quiet Talk and Digital Quiet Talk functions page 22 allow you to ignore unwanted calls Scrambler allows you to hold a conversation in complete privacy When activated any other party listening in on your channel will be unable to understand your conversation The transceiver scrambles your voice so that anybody listening to your conversation will not be able to understand what you are saying In order for members of your own group to understand your call while you are using the Scrambler all other members must also activate the Scrambler on their transceivers This scrambles everybody s voice while transmitting and descrambles the voice message on your own transceiver when you receive the message To activate the Scrambler press the key programmed as Scrambler To deactivate the Scrambler press the Scrambler key again Note There are 2 options for using the Scrambler Your dealer can activate or deactivate the built in Scrambler function of the transceiver or he she can add a more secure optional scrambler board to your transceiver Ask your dealer for details 24 VOX OPERATION VOX can be activated or deactivated by your dealer V
26. the specified charger and observe charging requirements If the battery is charged in unspecified conditions under high temperature over the regulated value excessive high voltage or current over regulated value or with a remodelled charger it may overcharge or an abnormal chemical reaction may occur The battery may generate heat or smoke rupture or burst into flame Do not pierce the battery with any object strike it with an instrument or step on it This may break or deform the battery causing a short circuited The battery may generate heat or smoke rupture or burst into flame Do not jar or throw the battery An impact may cause the battery to leak generate heat or smoke rupture and or burst into flame If the battery s protection circuit is damaged the battery may charge at an abnormal current or voltage and an abnormal chemical reaction may occur The battery may generate heat or smoke rupture or burst into flame 4 Do not use the battery pack if it is damaged in any way The battery may generate heat or smoke rupture or burst into flame Do not solder directly onto the battery If the insulator is melted or the gas release vent or safety function is damaged the battery may generate heat or smoke rupture or burst into flame Do not reverse the battery polarity and terminals When charging a reversed battery an abnormal chemical reaction may occur In some cases an unexpected large
27. w the antenna into the connector on the top of the transceiver by holding the antenna at its base and turning it clockwise until secure INSTALLING THE OPTIONAL ANTENNA INSTALLING THE BELT CLIP Note When installing the belt clip you must remove the battery pack from the rear of the transceiver 1 Remove the 2 screws from the rear of the transceiver then remove the small plastic black covering that was held in place 2 Insert the belt clip mount into the space on the rear of the transceiver 3 Using the 2 screws affix the belt clip in place Note Do not dispose of the plastic black covering If you remove the belt clip replace the covering into the space on the rear of the transceiver Either this covering or the belt clip must be in place otherwise the battery pack may not remain installed properly 10 If you are not using a speaker microphone install the cover over the speaker microphone jacks by sliding the cover s tab into the slot on the side of the transceiver until it snaps in place Note To keep the transceiver water resistant you must cover the speaker microphone jacks with the supplied cover INSTALLING THE COVER OVER THE SPEAKER MICROPHONE JACKS Note When installing the speaker microphone jack cover you must remove the battery pack from the rear of the transceiver INSTALLING THE OPTIONAL SPEAKER MICROPHONE Note When installing the optional speaker microphone and its
Download Pdf Manuals
Related Search