USER MANUAL - MBT Lighting
Contents
1. AUTO Dip 1 3 for Setting Dip 5 amp 6 Dip7 for with selection of 7 flashing for setting 1 0 0 fade static colors or not selection of 7 color Stand AUTO ON for 4 speeds changing Alone flashing or static 0 0 0 colors Sound X X X X X 1 0 NOTES DIP10 for setting Stand Alone or DMX Slave mode DIP 9 for setting AUTO or SOUND in Stand Alone mode DIP 8 for setting fade effect in AUTO mode DIP 7 for setting static color mode or color changing mode in AUTO In static color mode one can select single color using dip 1 3 Also one can set DIP 4 to ON position for flash effect and DIP 5 6 for desired flashing speed In color chasing mode set DIP 5 6 for desired color changing speed Static Color 1 2 3 Static Color 010 0 RED 1 0 0 GREEN 0 1 0 BLUE 1 1 0 YELLOW 010 1 ORANGE 1 0 1 PURPLE 0 1 1 CYAN 1 1 1 WHITE Flashing Speed 5 6 SPEED 0 0 HIGHEST 1 10 MEDIUM 1 0 1 MEDIUM 2 1 1 LOWEST A Auto mode When dipswitches 9 amp 10 are both set at OFF the fixture works in Auto mode Please check above DIPSWITCH SETUP for reference B Sound Active mode When dipswitch 9 is ON and dipswitch 10 is OFF the fixture works in Sound active mode Please check above DIPSWITCH SETUP for reference C MASTER SLAVE Mode Master set the dipswitch 10 of one LED PAR Light to OFF the other dip switches 1 9 control the speed2. requirements of all connected devices before use Following the cord cap manufacturer s instructions connect the yellow and green wire to ground earth the brown wire to live and the blue wire to neutral The table below details some pin identification schemes Wire Pin Marking Screw color Brown Live D Yellow or brass Blue Neutral N Silver Yellow or green Ground Green 2 2 Understanding DMX A About DMX DMX is the abbreviation of Digital Multiplex It s a universal protocol used by most audio lighting and controller manufactures as a form of communication between fixtures and controllers A DMX controller sends out DMX data instructions to the fixtures via 5 pin XLR cables The data travels through the DMX chain as a serial data DMX is a kind of common language allowing all products of different manufactures to be linked together and operate from a single controller as long as all fixtures and the controller are DMX compatible To ensure proper DMX data transmission when using several DMX fixtures try to use the shortest cable path possible B DMX Cable Requirements Your fixture LEDPAR64 uses 3 pin XLR cable as connection media C Connection of DMX Connect the DMX XLR cable to the female 3 pin XLR output of your controller and the other side to the male 3 pin XLR input of the fixture please refer to the figure below You 5 must chain multiple fixtures together through serial
3. LEDPAR64 USER MANUAL Table of Content Part General Information 1 1 IntroQUctiOnii eci icio pei eor pep rou arica 1 2 Safety Information mnererneenennene ee eee eee ee ne emen enne 1 3 Unpacklng ood des T4 Specifica A AN 125 rus E Part II Installation and Operation 2 1 AG Po Wei ica see de es eg ees 2 2 Understanding DMX 2er o dada A ADOUt DM B DMX Cable Requirement C Connection of DMX D DMX Addressing 2 3 Operation Instructions rrnrurrenennennannennenenanen reana nn aenen anne nnee A Auto Mode vuitton eae Ges taala B Sound Active Mode r nennnn nene nene eene rhe C Master Slave Mode n nrrnnnnenenennnnnnana nene nen nne nene 8 D DMX Mode Part III Maintenance and Cleaning mrrnenenerennenenenee nene nen nen enne 9 PART GENERAL INFORMATION 1 1 Introduction Thank you very much for purchasing the LEDPAR64 our 5 channel LED Par Lamp series product that can work in AUTO AUDIO and DMX mode To assure reliable performance it designed to please read the instructions in this manual thoroughly and carefully before application 1 2 Safety Information The following definitions of identifying the severity of the hazards associated with the products are used DANGER Imminently hazardous situation which if not avoided will cause death or serious i
4. h Avoid using any alcohol or solvents as they are harmful to the fixture
5. linking never split your DMX connections unless you are using our splitter signal amplifier such as SRL 144 Controller Fixture 1 Fixture 2 Fixture N D DMX addressing All fixtures should be given a DMX starting address when using a DMX controller so the correct fixture responds to the correct control signal This digital starting address is the channel number from which the fixture starts to listen to the digital control information sent out from the DMX controller The allocation of this starting DMX address is achieved by various combining the dipswitches This fixture employs 10 dipswitches to access its functions Normally the dipswitches from 1 to 9 are used for encoding DMX address the dipswitch 10 for enabling DMX mode init 123 4 567 8 9 10 ON OFF Dipswitch 1 address equals to 1 Dipswitch 2 address equals to 2 Dipswitch 3 address equals to 4 Dipswitch 4 address equals to 8 Dipswitch 5 address equals to 16 Dipswitch 6 address equals to 32 Dipswitch 7 address equals to 64 Dipswitch 8 address equals to 128 Dipswitch 9 address equals to 256 DMX address Dipswitch 1 Dipswitch 2 Dipswitch 9 2 3 Operation Instructions DIP SWITCH SETUP 12ON O OFF X ON or OFF switch 2 3 4 5 6 7 8 9 10 1 Function DMX Mode Dip 1 9 for DMX address setup 1 Master X X X X X X X 0 Slave X X X X X X X 1
6. njury WARNING Potentially hazardous situation which if not avoided could cause death or serious injury CAUTION Potentially hazardous situation which if not avoided may cause minor or moderate injury or property damage In addition it uses to alert against unsafe practice IGNORING A HAZARD WILL VOID ANY WARRANTY DANGER Ensure that the fixture is disconnected from the main power before performing any type of service or any cleaning procedure WARNNING No serviceable parts inside the fixture do not attempt to open it WARNNING The Installation must be performed by qualified professional in accordance with related local codes WARNNING Do not attempt to operate the fixture before read and understand the installation instructions and safety labels CAUTION Do not modify alter or attempt to service the LEDPAR64 CAUTION Always ground earth the fixture electrically CAUTION Refer all service to a qualified technician CAUTION When suspending the fixture above ground level or place it on the ground verify that the structure or surface can hold at least 10 times the weight of all installed devices 3 Unpacking The LED PAR PRO DMX has been thoroughly tested and shipped in perfect operating condition Check the shipping carton carefully for damage that may have occurred during shipping If the carton appears to be damaged carefully inspect your fixture for damage and be sure all accessories necessar
7. of the programs Master mode has three working ways auto with fade auto without fade and sound Please refer to DIPSWITCH SETUP above Slave set all the dip switch 1 amp 10 to ON 2 9 dip switches to OFF D DMX mode When dipswitch 10 is set at ON the fixture works in DMX mode By various combining the Dipswitches 1 to 9 you can set the address ranging from 1 to 512 At this moment the fixtures can be controlled by DMX controller or another fixture that has been designated as Auto or Sound Active mode with 5 channels receiving the data controlling the Red Green Blue brightness and strobe rate output of the fixture respectively Note the address encoded by combining dipswitches 1 to 9 function as initial channel address PART III MAINTENACE AND CLEANING Please refer to the following points during the normal inspection A Be sure all screws and fasteners are securely tightened at all times Lose screws may cause unexpected damage or injury B Electric power supply cables must not show any damage or frayed spot CAUTION Make sure that the power cord of the unit is disconnected from the mains before performing the following operation to avoid shock hazard We recommend if possible frequent cleaning of the device which will ensure its long lifespan and bright light output While performing the cleaning please always make sure that the power cord is disconnected from the mains and use a moist lint free clot
8. y to operate the fixture have arrived intact In case damage has been found or parts are missing please contact the sales person for further instructions You can find the following components inside the box D Aset of LEDPAR64 2 User Manual 3 A3 wire IEC power cable 4 Specifications Power Supply AC120V 60Hz LED Configuration 200PCS R 80PCS 0 044w G 66PCS 0 064w B 54PCS 0 064w Power Consumption 19W Dimension mm L785XW145XH150 Weight 2 8 kg Note Power configuration may differ by regions Please be sure the outlet in your area is suitable for the fixture 5 Features Low power consumption Maintenance free operation 100 000 hours rated LED lifespan 200 PCS of LED generates 16 7 million additive RGB colors DMX or stand alone mode with Master Slave function 18 built in programs accessed via DMX controller or manually Sound activated via built in microphone of adjustable sensitivity Brilliant light output PART Il Installation and Operation 2 1 AC power The fixture s mains lead may require a grounding type cord cap that fits your power distribution cable or outlet Consult a qualified electrician if you have any doubts about proper installation WARNNING For protection from dangerous electric shock the fixture must be grounded earthed The AC mains power supply shall have overload and ground fault protection CAUTION Verify that the feed cables are undamaged and rated for the current
Download Pdf Manuals
Related Search