FT-6315 Fan Free Touch Control Desktop POS Terminal
Contents
1. RJ11 connector in main connection area of a FT 6315 system can be used for controlling most of the common cash drawers available on the market However it is most recommended that the Posiflex CR 2000 or CR 2200 or CR 3100 or CR 3200 or CR 4000 or CR 4100 or CR 4210 or CR 6200 be used for best compliance The FT 6315 system will directly control the cash drawer using the cash drawer port CR both to operate the opening mechanism and to monitor the drawer open status Both functions may be accomplished under software control of the COM serial port Use the cable supplied with the cash drawer Part No 21863018010 for connection to the CR port in FT 6315 system This cable has a 6 pole plug at one end and an 8 pole plug at the other The 8 pole plug should be inserted into the connector marked signal cable from POS Printer at the rear of the cash drawer The 6 pole plug should be inserted in the connector marked CR found in the main connection area in the system The user may also use the optional 2 in 1 cash drawer control cable CCBLA 238 to control 2 cash drawers in 1 port It has a 6 pole plug at one end and two 8 pole plugs at the other The 6 pole plug should be inserted in the connector marked CR found in the main connection area in the system Each 8 pole plug should be inserted into the connector marked signal cable from UPS Battery Compartment Part 9 7 POS Printer at the rear of one of the c2. for IR touch Posiflex USB Touch Manager A program named Posiflex USB Touch Manager and a right click sticky button tool in the program group Posiflex USB Touch Tools is installed in the preloaded Windows system with a USB interface touch panel controller This program can also be obtained by download from the POSIFLEX web site RS232 Touch Controller If the FT system purchased is the leading edge Infra Red type touch models the touch controller is of RS232 interface using an internally reserved COM6 port The Posiflex USB Touch Manager above should be disregarded Once the RS232 touch controller driver is installed the user can utilize it to control the mouse emulation Please click Start Settings Control Panel and Elo Touchscreen or just click the elo icon in tool tray to engage this utility However with this touch controller driver certain display mode like full screen display of Windows DOS box should be avoided Part 19 POSIFLEX S ooogg 731454 Part 20
3. front cover LAWN status indicator HDD status indicator 11 LCD brightness contrast adjust buttons 12 CF reader status indicator ee LO a _ Part 4 a b c e f 13 14 15 16 17 18 19 20 21 22 23 24 2D 26 ZT 28 29 30 31 32 33 34 35 36 37 38 39 40 41 LCD panel tilt adjust button Power switch button Acoustic vent Back cover release button Reserved back cover lockup screw hole Back cover External power connector for power adaptor Power adaptor Internal power connector UPS battery connector Additional serial COM port Standard serial COM ports USB ports in back PS 2 KB port LAN port Cash drawer port VGA port Microphone input port Audio line out port LPT port Semi cut PCI plate window PS 2 mouse port PCI bracket PCI bracket fixing screw HDD bracket HDD hold spring HDD bracket handle UPS battery hold spring UPS battery compartment PRODUCT FEATURES Standard Features CPU Celeron M 1 5 GHz Fan free structure with Aluminum die cast main unit base casing for harsh environment Data storage device HDD 2 5 40 GB with status indicator in base or CF card Support Win 2000 Win XP Pro WEPOS and Linux OS High quality 15 TFT active matrix LCD panel Vertical type LCD panel with easy tilt angle adjustment from 10 to 45 Part 5 i j I n o p r S Brightness control by 2 push buttons in front
4. on the system Replace the battery as soon as the monitoring software indicates the battery is out of service Attempt to recharge a dead battery is dangerous A separate battery monitor is not required for this series DAILY MAINTENANCE GUIDE For regular cleaning of the FT systems please use only soft haired brush or dry soft cloth You may use moist soft cloth to remove stains when necessary Apply only proper amount of mild neutral detergent for obstinate stains Please note that never use Acryl dissolving solvent or Polycarbonate dissolving solvent You may apply ammonia based glass cleaner only on the screen surface CAUTION Risk Of Explosion If Battery Is Replaced By An Incorrect Type Dispose Of Used Batteries According To Local Regulations Part 2 INTRODUCTION PRODUCT PICTURES Front Views Part 3 Rear Views Detail inside back cover Please note that the picture for inside front and back cover is for reference only The actual layout may disagree from this picture if there is any difference in model or options selected or in the system revision Please follow the actual layout for cable connections in this case CAUTION DO NOT release the HDD compartment items 37 38 and 39 or system damage may occur PARTS IDENTIFICATION Optional base mount kit Touch panel LCD panel Optional side mount kit LOGO amp Power indicator Base unit Front cover CF memory card reader slot in front cover USB port in
5. pro Built in internal stereo speaker with 2 W audio amplifier Built in UPS function to support the system from intermittent power failure battery itself is an option Accidental power off protection The power switch is safely located inside a push open cover and it can be defined as a ON switch only through software command Part 6 Option Items Note The underlined items in the following list means that option must be a b c d e f g h 1 set prior to shipment from the factory The rest items can be set by the dealers DDR SDRAM memory expansion up to 2GB RS232 interface Infra Red type touch panel durable for 50 million touches min at same spot SATA control card with 2 5 SATA HDD installation Conversion cable for the additional COMS port to connect DB9 RS232 device Please note that only the correct conversion cable must be used 2 in 1 cash drawer control cable Integrated side mount upgrade kit lt FA 200 MSR lt or other later developed side mount upgrade kit Integrated base mount device lt PD2603 VED pole display lt PD308 LCD pole display lt PD7623 graphic LCD customer display lt or other later developed base device UPS battery in base Preload OS Part 7 INSTALLATION GUIDES CAUTION Before any installation or cable connection to the set please always make certain that the system is turned off and the external power source to the set is removed t
6. till release Main LCD Display For best viewing result please set your display resolution at 1024 x 768 with high color for FT 6315 In configuration of system memory max 32 MB can be shared as the video memory VGA Port The VGA port in the FT system supports Posiflex LCD monitor or touch monitor for 2 display This port supports either mirror mode identical image or extended mode dual display function for WinXP To support the DC power to the stand alone Posiflex monitor use the DC adaptor to connect into the monitor or use Posiflex VGA power cable and set an internal jumper in FT main board to supply the required power through the VGA connector Do not connect other monitor to this port before the power in this port is disabled Display Utility Driver The end user of the FT 6315 terminals is not supposed to install the utility drivers personally If an optional preloaded OS is ordered the required Part 17 driver will be already installed in the preloaded OS However the driver will always be available over our web site http www posiflex com FRONT COVER amp OTHER INDICATORS At left part on the front side of base unit there 1s a front cover Pick it up at the bottom notch and the CF memory card reader slot and an USB port for user s convenience na will be accessible To place the front cover back oened insert first ihe ioe eTA and then push the bottom edge in In the area between the front cover and the
7. will keep on flashing for few seconds before steady till the AC supply is stable Power ON OFF control The FT 6315 system implements electronic power control such that the main power to the system may be controlled by many methods as below 1 Hardware power switch 2 Software OFF command 3 Emergency power OFF Switching from OFF to ON requires a normal supply of the AC power Hardware Power Switch This button is located at top front corner of right side of base unit as in right picture and can be used to turn the system on and off alternatively This hardware switch can also be programmed to be an ON only switch through software command so that when this switch is accidentally pressed during system turned on the system just remains on and unaffected When using this feature please make sure that the software application has the ability to power off the machine In preloaded Windows Posiflex Power Switch Manager in Posiflex Tools in the Program Files helps managing these functions There must always be at least 10 seconds waiting before switching on again once the system is powered off successfully Software OFF Command The system may also be shut down under software control Please just follow the arrangement by your system integrator for this capability The FT also provides a specific means for the software to detect if the system is working on external or UPS battery power Due to this feature compatible software applic
8. LCD brightness adjust buttons there are several LED indicators for status other than the power status which is done by the LED module under logo in bottom center of the LCD panel The upper one of the 2 LED s near the LCD brightness adjust buttons indicates the operation status of the HDD and the lower one indicates for the CF reader The LED nearest to the front cover indicates the LAN status When it lights up in green the onboard LAN chip is linked When it flashes in yellow data transmission in LAN is in process The LAN status indication is also observable on the LAN connector in back cover area SERIAL PORTS COM1 2 3 4 5 In FT system there are 4 standard RS232 serial ports and 1 additional COMS port in form of a 10 pin RJ45 type modular connector available Please use only the optional conversion cable for COMS P N 21863233801 color black to connect a standard RS232 device All serial ports can supply a 5 V DC through pin 9 or 12 V DC through pin 1 after proper jumper setting change Please always change the jumper back to disable the power in these ports once the specific devices are no longer attached otherwise damages will occur if non designated device is connected to such power supports On COM 1 port of the FT system a COM 1 terminator will be installed at delivery Please always occupy COM1 serial port by a suitable serial device or this terminator If this port is left vacant or connected with something like a mou
9. POUSIFLEX FT 6315 Fan Free Touch Control Desktop POS Terminal User s Manual FCC Notes Rev Original This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions manual may cause interference to radio communications It has been tested and found to comply with limits for a Class A digital device pursuant to subpart J of Part 15 of FCC Rules which are designed to provide reasonable protection against interference when operated in a commercial environment Operation of this equipment in a residential area is likely to cause interference in which case the user at his own expense will be required to take whatever measures to correct the interference Warranty Limits Warranty terminates automatically when any person other than the authorized technicians opens the machine The user should consult his her dealer for the problem happened Warranty voids if the user does not follow the instructions in application of this merchandise The manufacturer is by no means responsible for any damage or hazard caused by improper application About This Manual Posiflex Technologies Inc has made every effort for the accuracy of the content in this manual However Posiflex will assume no liability for any technical inaccuracies or editorial or other errors or omissions contained herein nor for direct indirect incidental consequential or otherwise damages including without li
10. ash drawers The cable lengths for the two 8 pole plugs are different Use the shorter one for the original cash drawer CRI and use the longer one for the extended cash drawer CR that will be distinguished by the software command INSTALLING BASE MOUNT KIT OPTION When the FT 6315 series is ordered with the base mount upgrade kit like customer display PD 2603 2603U PD 308 308U or PD 7623 option the customer display together with the pole for installing them to rear of base will be delivered in separate package from the system unit Please follow the step by step installation guides below with reference to the attached pictures The customer display will occupy one USB or COM port in the connection area Consult your distributor for technical support on setting up the 5V DC supply to the COM port used if the customer display is of the serial interface type The USB interface type such as PD 2603U or PD 308U will be powered through the USB port without specific setting 1 First open the back cover of FT system base by pastes in n the circled buttons on both sides as in the right pictures and lift from bottom edge to on rm 1 remove the back cover q O 2 Remove the cover on rear edge of the base top cover of FT system by first removing the 2 arrowed screws in the left picture and then pushing the wedge shaped pole cover up 3 Insert the base of base mount upgrade kit from top of FT system base with the flat side of the pol
11. ations have the ability to change operating conditions when running on standard backup power The software programmer may take reference from the FT technical manual to apply such features Emergency Power OFF In case of serious system halt due to any reason the system could fail to be powered off through normal means Press and hold the Power ON OFF Switch for Emergency Power Off Release the switch after the system powered off It will take about 4 seconds if the hardware switch is set to ON OFF mode and it takes about 10 seconds if the hardware switch is set to ON only Part 16 mode If there appears to be some serious trouble for system restart or even this emergency power off please disconnect the UPS battery if installed and the AC power supply for few minutes This may allow all hardware registers to reset DISPLAY ISSUES LCD Touch Panel Tilt Adjust Please find the rectangular plastic button at rear of the display base as enlarged in the right picture Push it down from back of the panel towards the front side to adjust the display up and down Release the button when done The panel will lock firmly for application LCD Panel Brightness Adjust There are 2 LCD panel brightness control buttons on front side of base for digital control over the LCD panel brightness A brief touch at the right left button makes the LCD display brighter dimmer by a minute amount A holding touch makes continuous change
12. e base facing the back cover direction and screw back the 2 screws as in the right picture Connect the interface cable to appropriate port SIDE MOUNT UPGRADE KIT When a side mount upgrade kit option such as FA 200 is ordered with the FT 6315 system this option is already installed in the delivery No matter the kit itself contains MSR only finger print sensor only or both options the connection to the FT 6315 system is through an internal cable in right side cover of the LCD touch unit Remove the 2 circled screws in the left picture to remove the cover for side mount upgrade kit Take out the cable inside this cover as circled in the left picture here and connect it to connector inside the side mount upgrade kit as arrowed in the same picture ho Xx Part 10 Gently arrange the excessive length of this cable back in the hole and screw fit it back to the position originally occupied by the cover as in the right picture Please reserve the cover if there is chance to have the side mount kit removed in the future BARCODE SCANNER OPTION When a PS 2 KB interface barcode scanner is installed in the system a connection of a normal PS 2 keyboard or a Posiflex programmable keyboard could become obligatory by some OS Therefore if there will be no keyboard installed for such OS it is advisory to use an USB interface type barcode scanner instead of the PS 2 KB interface type AUDIO LINE OUT PORT The audio outp
13. east 25 mm air clearance around any top or side ventilation holes with a free flow of air around the unit at ALL times for the installation Operating Environment The equipment must not be operated or stored in extremes of both temperature and humidity moisture Operating range 5 C to 40 C and up to 80 humidity non condensing max wet bulb 26 C UPS Battery option General care The UPS battery is consumables beyond product warranty Please definitely observe the alerts in beginning of this manual If the equipment is to be powered off for more than few days please always disconnect the battery from the system Reconnect it and turn on the system to recharge the battery for 1 2 hours every 3 months for temperature lower than 30 C Recharge for 1 2 hours every month for temperature over 30 C Temperature above 40 C must be strictly avoided as it could cause termination of battery life and unexpected result even if the battery is not in work The UPS battery can support basically the data preservation and smooth running of the system during intermittent or few minutes within 30 min depending on loading and battery condition power failure Battery replacement In the preloaded OS for a FT system there is a built in utility Power Manager that will interface the UPS battery monitor status with user When battery monitor disables the battery charging as designed while the UPS function of the system is originally enabled in othe
14. erating system The System Integrator shall take care of software restoration after OS recovered A Posiflex supplied USB interface CDROM drive will be required for such action Other brand CDROM drive may require its specific driver different from what supported in the recovery CD Please use the recovery CD in rescue operation only Using it otherwise may wipe out whatever stored in the HDD All upgrade devices drivers needed for manual installation in usual way are available in the subfolder drivers in OS recovered HDD and the latest versions of these required drivers will be available on our web http www posiflex com tw Then follow instructions from your system integrator for software recovery OPERATING SYSTEM INSTALLATION This product is a highly professionalized equipment The installation of an OS into a machine without any preloaded OS could constitute major difficulty for average user or obstacle by possibly unintentional negligence even for PC veterans to accomplish such a task Therefore OS installation into Part 12 a system without preloaded OS is highly discouraged Posiflex shall not be responsible for any technical support to questions arisen due to non preloaded OS Part 13 USING THE TOUCH TERMINAL APPLICATION ENVIRONMENT It is very important that you check the following operational guidelines Ventilation This terminal must NOT be operated in an environment with restricted ventilation There must be at l
15. in right picture to release the lower part of back cover Please note that there are 2 hooks on top edge of back cover holding to the base as marked on upper part of the picture Carefully release the back cover from the hooks to show the main connection area for cable connections and installation of Part 8 E E Push This Button and also The One on The Other Side to Open Back Cover 41 Ay optional UPS battery Note Never press the HDD hold spring carelessly or system damages could occur The user shall be responsible for such kind of damage INSTALLING UPS BATTERY OPTION When the FI 6315 system is ordered UPS Battery Connector with the UPS battery the UPS battery is separately stored in the carton at delivery Please take it out and place it into the battery compartment by first pressing down the UPS battery hold spring and then allow the spring to spring back and hold the UPS battery in the compartment as indicated by lower rectangle in picture at right Connect the cable to its connector above the battery compartment in correct orientation observe the shape of the connector red wires at left only when the system is about to power up for operation Always disconnect the UPS battery when the system is to be left powered off for more than few days Please pay particular attention to the environment requirement for UPS battery in next chapter USING THE TOUCH TERMINAL CONNECTING CASH DRAWER OPTION The
16. le the power outlet and any power fusing arrangements must conform to local safety regulations Please never do any connection disconnection when system is still powered on Please always keep the system in a free air circulation POWER ON OFF Power Indicator POSIFLEX The power indicator is the backlight LED module under the logo that serves for several purposes The relationship between the indicator status and other conditions is summarized in following table System External i Indicator Status UPS Battery Powering Up Off Not possible Off Not allowed O O O Blue Not required Blue flash Not required Blue rapid flash pon fo uae i Not required low capacity The LED module indicates Power StandBy status When it lights up in green it means that the external AC power is standing by with the system powered off It turns into blue when the system is powered up This module also indicates the status of system working on battery power by flashing in 0m Or Off Of Green Off On __ Noinfluence Allowed O O On Of ff ff ff ff On On On Part 15 7 blue The blue light will flash rather fast when the UPS battery approaches a fully discharged condition to remind the operator that power will soon finish In few seconds the whole system will soon be automatically turned off and the LED module will be OFF In case the AC power resumes during the usage of the battery power the flashing LED
17. mitation loss of data or profits resulting from the furnishing performance or use of this material This information is provided as is and Posiflex expressly disclaims any warranties expressed implied or statutory including without limitation implied warranties of merchantability or fitness for particular purpose good title and against infringement The information in this manual contains only essential hardware concerns for general user and is subject to change without notice Posiflex Technologies Inc reserves the right to alter product designs layouts or drivers without notification The system integrator shall provide applicative notices and arrangement for special options utilizing this product The user may find the most up to date information of the hardware from web sites http www posiflex com or http www posiflex com tw or http www posiflexusa com All data should be backed up prior to the installation of any drive unit or storage peripheral Posiflex Technologies Inc will not be responsible for any loss of data resulting from the use disuse or misuse of this or any other Posiflex product All rights are strictly reserved No part of this documentation may be reproduced stored in a retrieval system or transmitted in any form or by any means electronic mechanical photocopying or otherwise without prior express written consent from Posiflex Technologies Inc the publisher of this documentation Copyright P
18. o prevent electric hazard Never touch any metal pin in the connectors or circuits to avoid high voltage hazard or electrostatic discharge damage unless the operator is well grounded Failure to do the above will void the product warranty TECHNICAL ENHANCEMENTS Applicable technical enhancements in FT 6315 series include serial COM port power supply settings RTC battery replacement VGA port power supply setting DRAM upgrades and adding a half length PCI adapter card All these technical enhancement operations require purchase of applicable Technical Manual from Posiflex or consultation from Posiflex authorized dealers and should be handled only by a qualified technician NON USER INSTALLABLE OPTIONS When the FT 6315 system is ordered with options like expanded system memory or side mount upgrade kit the option s is are already installed in the system delivered Therefore no more installation is required HALF LENGTH PCI EXTENSION CARD Adding a half length PCI extension card is possible However the whole operation will involve cautiously accessing the interior of the system replacing the slot window metal plate applying the card and installing its driver Therefore only a computer expert can perform this operation on his own risk OPENING BACK COVER The FT 6315 series is constructed for very easy maintenance Press inward both back cover release buttons at lower rear corners on both sides of the system base unit circled
19. osiflex Technologies Inc 2007 All brand and product names and trademarks are the property of their respective holders P N 16600900010 Part 1 7 ALERT TO OUR HONORABLE CUSTOMERS Please always read thoroughly all the instructions and documents delivered with the product before you do anything about it Don t take any premature action before you have a full understanding of the consequences This product contains inside a Lithium battery and maybe also a sealed type Lead acid battery if the UPS battery option is ordered Please always follow local environmental protection laws regulations for disposal of used batteries and always replace only with battery of same type If you have an UPS battery installed in the product lt gt lt gt Temperature above 40 C must be strictly avoided as it could cause termination of battery life and unexpected result even if the battery is not in work Do not power off the system just by shutting off the AC power leaving the battery supporting the whole system till completely exhausted Repeatedly using it up or improper maintenance reduces the battery life dramatically Always fully recharge the battery at least once every 3 months if the battery is not connected Always disconnect the UPS battery from the system if the system is to be left OFF for more than 72 hours to prevent possible damage Only connect the UPS battery back right before you are going to re power
20. r words the UPS battery is found out of order if actually installed there will be a popup Ma as ie picture at right asking the user to agree disabling the No ey ee See Soe n UPS function The system will operate under fas poets ene Do you want to stop showing this message deactivated UPS function no matter agreed or not However the monitoring goes on and the popup message will come back on next system power up boot if not agreed In any case please replace the used up UPS battery at power off if the battery is well Part 14 connected there but found inoperable by such messages Emergency treatment The battery is constructed maintenance free and leakproof It is well protected in FT system as long as the ambient temperature remains below 30 C and the ventilation of the FT system remains free However should any accident happen and the sulfuric acid from the battery spills on skin or clothing wash immediately with water If the acid comes in contact with eyes rinse eyes with large amount of clean water and see a doctor immediately A larger external battery may be connected to give an extended operation Please check your dealer about this capability when required WARNING If there are any signs of over charging or leakage of electrolyte please contact your dealer immediately Power Supply The operating voltage range of the power adaptor should cover the local power supply for proper operation The power cab
21. se the power switch management and the cash drawer control may fail to work correctly An RS232 MODEM is also not applicable to this port It is recommended to use other COM port instead CUSTOMER DISPLAY Please follow the instructions on the manual that comes along with the customer display when it is installed Part 18 7 TOUCH FUNTION Mouse Emulation The touch panel in FT system uses USB interface as standard Only the optional InfraRed type touch panel of FT 6315 uses RS232 interface When the touch driver is properly installed this touch panel works exactly like a standard mouse for both interfaces However if the system is running under safe mode most drivers are disabled in this mode and the touch panel calibration is therefore not guaranteed It is recommended to use a standard USB mouse or keyboard in this mode All the below mentioned mouse emulation functions can be manipulated through relevant software The system can give a beep and a click on the left button of a mouse at the point when the touch panel is touched If the point touched is dragged across the screen surface it works as the mouse drag and drop feature If the point is touched released and touched within a short time interval it is double clicking left button of the mouse To obtain the effect like clicking on the right button of a mouse you have to use the right click sticky button tool for USB touch or you have to go into the controller
22. side of base Durable resistive type touch panel that endures 35 million touches min at same spot leading edge Infra Red type optional Spill proof water resistant structure allowing easy cleaning Easy maintenance construction Various I O ports supported including 1 one PS 2 KB port 2 one PS 2 mouse port 3 4 serial ports with capability for 5V and 12V DC support in form of DB9 connectors with one additional serial port in form of 10 pin RJ45 modular jack 4 one parallel port 5 4 standard USB ports 1 in front 3 in back with 2 additional internal used USB ports 6 one LAN port 10 100 base T Ethernet with LAN status indicators on jack and one indication LED in front side of base green for link orange for data transmission 7 one external VGA monitor port 8 one PCI extension slot 9 one DIN 4 pin lock type DC 12 V power input connector 10 one UPS battery connector 11 one cash drawer connector for control over max 2 cash drawers 12 one microphone input port 13 one audio line out port 14 one CF memory card reader slot on front side of base Touch control functions left right button double click drag amp draw Dual display support per OS capability VGA memory size shared from system memory 8 32 MB Support high performance DDR SDRAM with maximum memory size 2GB in 2 modules Integrated structure for side mount upgrade kit like FA 200 with software programmable MSR parameters for Win 2000 or Win XP
23. t be done WITHOUT any connection to the AC power The operating voltage selection switch is located close to the power input connector in the main connection area inside the back cable cover The switch should indicate either 115 volts or 230 volts When set at 115 volts the acceptable power supply voltage range is 103 volts to 122 volts whilst at 230 volts the acceptable power supply voltage ranges from 207 volts to 244 volts The power supply cable should first be connected to the power inlet but NOT the wall socket This cable should be consolidated with other cables and come out of the connection area through the bottom opening of the chassis OPERATING SYSTEM RECOVERY For FT systems with operating system in the Compact Flash Card once the Compact Flash is damaged for any reason the thin client may fail to boot A bootable new Compact Flash Card will be required to have the workstation back to work Please follow instructions given by the System Integrator to deal with situations like that One more advice for CF Card application is that in spite of the fact that it is used in the way like an ordinary HDD usual utilities such as FDISK EXE or FORMAT COM shall never be used on CF Card otherwise the boot sector of operating system itself may be damaged and causing the CF Card no longer bootable For FT systems preloaded with Windows XP Pro or WEPOS on HDD Posiflex provides recovery CD delivered with the touch terminal for the preloaded op
24. ut port is internally connected to audio amplifiers and speakers So this port must be connected to a pair of speakers with booster or amplifier only CONNECTING INTERFACE CABLES Please connect all required interface cables to the appropriate connectors Please make sure that each connector is connected to the correct port with the correct orientation Damages due to incorrect connection or orientation are not covered by product warranty Some connectors like the LAN or CR connector or the optional conversion cable for additional COMS port have to be gently inserted until a click is heard Please note that the click lock spring has to be pressed down prior to pulling out the connector for later removal of the cables from these ports It is recommended that connectors such as the external VGA and LPT connector be screwed into place once seated Connect the cables to appropriate external devices Please make sure that each connector has to be connected to the right device in the right way CAUTION On doing any insertion or extraction of any connector please always hold the connector head itself instead of pulling on the cable wire Failure to do this could damage the cable and jack that is considered as an artificial destruction and is not covered by the warranty Part 11 CONNECTING AC POWER The power supply operating voltage must be checked to support the city power supply specification and switch selected if necessary This mus
Download Pdf Manuals
Related Search