Home

User Manual - B&H Photo Video Digital Cameras, Photography

1. Moving the right stick up and down changes the aircraft s fonward and backward pitch Push the stick up to fly forward and down to fly backward The Inspire 1 will hover in place if the stick is centered Push the stick further away from the center position for a larger pitch angle maximum 35 and faster flight Moving the right stick control left and right changes the aircraft s left and right pitch Push left to fly left and right to fly right The Inspire 1 will hover in place if the stick is centered Push the stick further away from the center position for a larger pitch angle maximum 35 and faster flight Gimbal Dial Turn the dial to the right and the camera will shift to point upwards Turn the dial to the left and the camera will shift to point downwards The camera will remain in its current position when dial is static 26 2014 Dul All Rights Reserved INSPIRE 1 User Manual Flight Mode Switch Toggle the switch to select the desired flight mode You may choose between P mode F mode and A mode F ats Figure Flight Mode FAS F mode AT A cli A mode Pc P mode Path P mode Positioning P mode works best when GPS signal is strong There are three different states of P mode which will be automatically selected by the Inspire 1 depending on GPS signal strength and Vision Positioning sensors P GPS GPS and Vision Position
2. gg 8 8 C DE 4 EE C 0 W N Ifthe Aircraft Status Indicator blinks red and yellow after the calibration move your aircraft to a different location to carry out compass calibration 0 Calibrate the compass before each flight Launch DJI Pilot App follow the on screen instruction to calibrate the compass When to Recalibrate 1 When compass data is abnormal and the Aircraft Status Indicator is blinking red and yellow 2 When flying in a new location or a location that is different from your last flight 3 When the mechanical structure of the Inspire 1 has changed i e changed mounting position of the compass 4 When severe drifting occurs in flight i e the Inspire 1 does not fly in straight lines Auto Take off and Auto Landing Auto Take off Use auto take off to take off your aircraft automatically if the Aircraft Status Indicator displays blinking green Follow the steps below to use auto take off 1 Launch DJI Pilot app enter Camera page 2 Ensure the aircraft is in P mode 3 Go through the pre flight checklist 4 Tap and confirm flight condition Slide to confirm and take off 5 Aircraft takes off and hovers at 1 5 meters above ground 50 2014 DJI All Rights Reserved INSPIRE 1 User Manual Auto Landing Use auto landing to land your aircraft automatically if the Aircraft Status Indicat
3. N Ensure to upgrade the remote controller s firmware to the latest version after you upgrade the aircrafts firmware he remote controller may dis link to the aircraft after upgrading Re link the remote controller and aircraft Confirm the upgrade result according to the gimbal sounds or the upgrade result document It is normal if the aircraft sounds or the LED blinking during the upgrading process The on screen rate of progress may be not accurate Ensure there is only one firmware package in your SD card otherwise it may cause abnormal Only the storage device that is formatted in FAT32 and ExFAT file system is supported for aircraft and remote controller upgrade process Delete automatically generated txt files xxx_GS TXT in the SD cards when upgrading multiple remote controller FCC Compliance FCC Compliance This device complies with part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 This device must accept any interference received including interference that may cause undesired operation Changes or modifications not expressly roved by the party responsible for compliance could void the user s authority to operate the equipment Compliance Information FCC Warning Message Any Changes or modifications not expressly roved by the party responsible for compliance could void the user s authority to operate the equ
4. INSPIRE 1 User Manual Remote Controller Remote Controller Profile The Inspire 1 Remote Controller is a multi function wireless communication device that integrates the video downlink ground system and aircraft Remote Controller system The video downlink and aircraft Remote Controller system operate at 2 4 GHz with maximum transmission distance of 2km The remote controller features a number of camera functions such as taking and previewing photos and video and controlling gimbal motions The remote controller is powered by a 2S rechargeable battery The current battery level is displayed by LEDs on the front panel of the remote control Compliance Version The Remote Controller is compliant with both CE and FCC regulations e Operating Mode Control can be set to Mode 1 Mode 2 Mode 1 The right stick serves as the throttle Mode 2 The left stick serves as the throttle N Do not operate more than 3 aircrafts within in the same area size equivalent to a soccer field to prevent transmission interference Remote Controller Operations Powering On And Off The Remote Controller The Inspire 1 remote controller is powered by a 2S rechargeable battery with a capacity of 6000mAh The battery level is indicated by the Battery Level LEDs on the front panel Follow the steps below to power on your remote controller 1 When powered off press the Power Button once and the Battery Level LEDs will display the current batter
5. lt LED is flashing lt LED is off Battery Level LED1 LED2 LEDS LED4 Battery Level 87 5 100 19 87 5 62 5 5 50 62 5 37 5 50 25 37 5 12 5 25 0 12 5 AA ATR ATR FA AVR ES MAN EAN A ATR MAN AES MAN ES ES EN PS 0 INSPIRE 1 User Manual Battery life The battery life indicates how many more times the battery can be discharged and recharged before it must be replaced When the battery is powered off press and hold the Power Button for 5 seconds to check the battery life The Battery Level Indicators will light up and or blink as described below for 2 seconds Battery Life LED1 LED2 LED3 LED4 Battery Life 90 100 80 90 70 80 60 70 50 60 40 50 30 40 20 30 AEASATR ATR EE KARAKARAABLA N MAN S AWS A ES EN ESA below 20 Z When battery life reaches 0 it can no longer be used For more information about the battery launch DJI Pilot app and check the information under the battery tab Charging the Intelligent Flight Battery 1 Connect Battery Charger to a power source 100 240V 50 60Hz 2 Open the Protection Cap and connect the Intelligent Flight Battery to the Battery Charger If the battery level is above 95 turn on the battery before charging 3 The Battery Level Indicator will display the current battery level during charging The Intelligent Flig
6. 2M D 39m ND N83 ws CT M S Vision Positioning Status Icon is highlighted when Vision Positioning is in operation Flight Telemetry e N Flight attitude is indicated by the flight attitude icon 1 The red arrow shows which direction the aircraft is facing 2 Light blue and dark blue areas indicate pitch 3 Pitching of the boundary between light blue and dark blue area shows roll angle Home Point Settings Q Tap this button to reset the current home point You may choose to set the aircraft take off location the remote controller s current position or the aircraft s current position as the Home Point Return to Home RTH d Initiate RTH home procedure Tap to have the aircraft return to the latest home point 2014 Dul All Rights Reserved INSPIRE 1 User Manual 16 Gimbal Operation Mode Refer to Gimbal Operation Mode P38 for more information 17 Auto Takeoff Landing 4 1 Tap to initiate auto takeoff or landing 18 Back Tap to return to the main GUI Map User can view the current flight route in a larger map view in this page You can also perform Auto take off and Landing in the page Academy Download user manual view online videos and using flight simulator User Center You can sync the picture and videos to the mobile device view the flight records and check your Dul account status in the User Center Use the DJI registered account to login to the User
7. 3 Enter Camera view and tap on and then tap Linking Remote Controller button as shown below RC Control Setting Remote Control Calibration Stick Mode Default stick mode is Mode 2 changing stick modes alters the way the aircraft is controlled Do not change unless familiar with your new mode C1 Gimbal Pitch Yaw C2 Reset gimbal yaw Le So xa CS o You can customize the C1 and C2 buttons on the back f O a i of the remote controller EN Linking Remote Controller 32 INSPIRE 1 User Manual 4 The remote controller is ready to link The Remote Controller Status Indicator blinks blue and beep sound is emitted RC Control Setting Remote Control Calibration Stick Mode Searching for aircraft frequency Default stick mode is Mode 4 timeout in 54 seconds Do not change unless familia m Press the linking button on the aircraft to link this remote controller Cancel You can customize the C1 and C2 buttons on the back of the remote controller Linking Remote Controller 5 Locate the Linking button on the front of the aircraft as shown in the figure shown below Press the Linking button to start linking The Remote Controller Status Indicator will display solid green if Link is succeed A Remote controller cannot link to the aircraft if the remote controller is set as Slave Meanwhile the Slave remote controller ca
8. GPS Module Used to pinpoint the location of the remote controller 21 Back Left Button Customizable button in DJI Pilot app 22 Power Port Connect to a power source to charge the remote controller s internal battery 23 Back Right Button Customizable button in DJI Pilot app Aircraft This chapter describes the features of the Flight Controller Vision Positioning system and the Intelligent Flight Battery 2014 DJI All Rights Reserved 11 1e49JlV Aircraft Flight Controller The Inspire 1 s flight controller is based on Dul flight controller with several enhancements such as new flight mode and new safe mode Three safe modes are available Failsafe Return Home and Dynamic Home Point These features ensure the safe return of your aircraft if the control signal is lost A flight recorder stores crucial flight data for each flight Flight Mode Three flight modes are available The details of each flight mode are found in the section below P mode Positioning P mode works best when GPS signal is strong There are three different states of P mode which will be automatically selected by the Inspire 1 depending on GPS signal strength and Vision Positioning sensors P GPS GPS and Vision Positioning both are available and the aircraft is using GPS for positioning P OPTI Vision Positioning is available but the GPS signal is not Aircraft is using only Vision Positioning for hovering P ATTI Ne
9. Center ddy 10 Id Ira Flight This chapter describes the flight safety and flight restrictions 44 2014 DJI All Rights Reserved Flight Once pre flight preparation is complete it is recommended to carry out the tasks in the Inspire 1 Pilot Training Guide to prepare for more complex flight manoeuvres and learn to fly safely Ensure that all flights are carried out in a suitable location Flight Environment Requirements 1 Do not use the aircraft in severe weather conditions These include wind speed exceeding 10m s Snow rain and smog 2 Only fly in open areas Tall buildings and steel structures may affect the accuracy of the on board compass and GPS signal 3 Avoid from obstacles crowds high voltage power lines trees or bodies of water 4 Minimize electromagnetic interference by not flying in area with high levels of electromagnetism including mobile phone base stations or radio transmission towers 5 Aircraft and battery performance is subject to environment factor such as air density and temperature Be very careful when flying 14700 feet 4500 meters or more above sea level as battery and aircraft performance may be reduced 6 The Inspire 1 cannot operate within the polar areas in P mode Flight Limits and Flight Restriction Area Flight limits on height and distance can be set The details of these flight limits are described in the following section All unmanned aerial vehicle UAV operators
10. LEDA blinks three times per second Battery Protection Item Over current detected Short circuit detected Over charge detected Over voltage charger detected Hoom temperature is not suitable for charging Hoom temperature is not suitable for charging After any of the above mentioned protection issues are resolved press the button to turn off the Battery Level Indicator Unplug the Intelligent Flight Battery from the charger and plug it back in to resume charging Note that you do not need to unplug and plug the charger in the event of a room temperature error the charger will resume charging when the temperature falls within the normal range A DJI does not take any responsibility for damage caused by third party chargers ule jd How to discharge your Intelligent Flight Battery Slow Place the Intelligent Flight Battery into the Inspire 1 s Battery Compartment and power it on Leave it on until there is less than 8 of power left or until the battery can no longer be turned on Launch the DJI Pilot app to check battery level Rapid Fly the Inspire 1 outdoors until there is less than 8 of power left or until the battery can no longer be turned on 22 Remote Controllers This chapter describes the features of the remote controller that includes aircraft and remote controller operations and dual remote controller mode 2014 DJI All Rights Reserved 23 SJ9 OJ1UO2 2JOWOH
11. aircraft s orientation to avoid collision during the Smart HTH Press the Smart RTH button once to start the process press the Smart RTH button again to exit omart RTH and regain the control 1e49JlV 1e49JlV INSPIRE 1 User Manual Low Battery RTH The low battery level failsafe is triggered when the DJI Intelligent Flight Battery is depleted to a point that may affect the safe return of the aircraft Users are advised to return home or land the aircraft immediately when these warnings are shown DJI Pilot app will advise user to return the aircraft to the Home Point when low battery warning is triggered Aircraft will automatically return to the Home Point if no action is taken after 10 seconds countdown User can cancel the RTH by pressing once on the RTH button The thresholds for these warnings are automatically determined based on the current aircraft altitude and its distance from the Home Point Aircraft will land automatically if the current battery level can only support the aircraft to land to the ground from the current altitude User can use the remote controller to control the aircraft s orientation during the landing process The Battery Level Indicator is displayed in the DJI Pilot app and is described below Critical Low battery level Sufficient battery warning Red level Green Low battery level warning Remaining flight time L Power requires to return home Battery level indicator Battery Level Aircraft Statu
12. and down at least four times 4 Power off the aircraft Travel Mode Togglex4 Landing Mode N Battery must be fully charged before using it for the first time Refer to Charging the Intelligent Flight Battery P21 for more information e If you have purchased the dual remote controller version you must use the Master remote controller to deactivate Travel Mode Refer to Setting Up Dual Remote Controllers Mode P30 section for more infromation about Master remote controller Be sure to remove the gimbal from the aircraft before switch from Landing Mode to Travel Mode Installing Gimbal and Camera 1 Remove Gimbal Cover 2 Rotate the Gimbal Lock to the unlocked position to the right when facing the nose of the aircraft 3 Insert the gimbal by aligning the white mark on the Gimbal 4 Rotate the Gimbal Lock back into the locked position Q Gimbal Cover Locked N Ensure the Micro SD card is correctly inserted into the camera 2014 Dul All Rights Reserved 1 2H01d JONPOld e jo4d 19npoJd INSPIRE 1 User Manual Attaching Propellers Attach propellers with the black nut onto motors with the black dot and spin counter clockwise to secure Attach propellers with gray nut onto motors without a black dot and spin clockwise to secure N Place all propellers onto the correct motor and tighten by hand to ensure security before flight Pre
13. controller battery level is above 50 Step 2 Prepare the Firmware Update Package 1 Extract the all downloaded file into the root directory of the SD card or the USB disk 2 Insert the SD card into a SD card reader or the USB disk onto the remote controller USB port when remote controller powered off If you do not have a SD card reader you may insert the SD into the gimbal and connect the gimbal with remote controller to upgrade the remote controller Step 3 Update the Remote Controller 1 Power on the remote controller and wait for 20 seconds until the upgrade begins 2 It will take approximately 10 minutes to complete the firmware update The camera will sound a beeping sound and the Status LED on the remote controller shows solid blue to indicate the update is in progress The Status LED on remote controller shows solid green and beeping sound will stop if the upgrade is completed with success The Status LED on remote controller shows solid red if upgrade is failed Try upgrade again 60 2014 DJI All Rights Reserved INSPIRE 1 User Manual Updating Intelligent Flight Battery Firmware The Intelligent Flight Battery is upgraded during the aircraft firmware upgrade process It is recommended to keep the upgrade package files in your SD card Upgrade the Intelligent Flight Battery If DJI Pilot App prompts The upgrade will start automatically if the aircraft does not connect to the DJI Pilot app after power cycling the aircraft
14. could void the user s authority to operate the equipment KCC Warning Message HS TUE ESSuui ESMZSo lena UBAN HAE A H c tT gel de tuc BSS UZA 7AtS Ol WS 0 NCC Warning Message KS eat Se Sie is B ROUES AEM ETT AT BARRERAK SEER D AWTS EGRE RERE ETORRERA ESL AMX ERNER TENAS KARB TERRI ESS FRISH BURGAS IAEA AERAR aA RRNA ERRON BERLE FAKERAHSRK EN Seti 62 2014 DJI All Rights Reserved The content is subject to change Download the latest version from www dji com support 2014 DJI All Rights Reserved
15. support GoPro attachments The gimbal is designed to hold Dul cameras only When will ground station functionality be available The Inspire 1 does not currently support ground station Ground station will be available with future firmware updates Is the camera s exposure automatic The exposure can be set to Auto for automatic changes or Manual if you wish to use a specific setting Can see the size of images through the app Yes you can preview image or video sizes through the DJI Pilot app How much weight can the Inspire 1 carry without its included camera We do not recommend flying with any payload other than the included DJI gimbal and camera Do you have an LCD monitor available for the Inspire 1 No DJI does not sell LCD or HD monitors for the Inspire 1 However you can output the live streaming video to a compatible monitor or mobile device of your own How long does it take to charge the battery Does it comes with a charger Yes all Inspire 1 units come with standard TB47 charger With the standard TB47 100W charger it takes 85min to fully charge a 4500mAh battery Are the two remote controllers the same Should setup the remote controllers in the app or somewhere else to control the camera and aircraft separately The two remote controllers are physically identical You can set the remote controllers to either Master or Slave through the DJI Pilot app if you wish to use dual controller mode Where c
16. the desired IOC modes from the DJI Pilot app IOC only works under F mode and user must toggle the flight mode switch to F mode to activate IOC Refer to the table below Its forward direction is pointing to the nose direction when recording which is fixed until you re record it or exit from CL Hecord a Home Point HP and push Pitch stick to control the aircraft far from or near to the HP Point of Interest Record a point of interest POI the aircraft can circle around the POI and the nose always points to the POI Course Lock CL Home Lock HL Point of Interest POI X Home Lock and Point of Interest feature are coming soon Prerequisites of IOC Use the IOC feature under the following condition Modes IOC GPS enabled GPS Flight Distance Limits Course Lock No None None Home Lock Yes ll Aircraft 210m Home Point POI Yes 8 ul Aircraft m 9500m Point of Interest Using IOC Enable the IOC feature by tapping Enable IOC in the setting page of the DJI Pilot app Toggle the Flight Mode Switch to F mode and follow the on screen instruction to use IOC feature xipueddy xipueddy INSPIRE 1 User Manual Firmware Updates Follow the process described below to upgrade the aircraft remote controller and battery Updating the Aircraft Firmware Step 1 Check Battery and SD Card Capacity Ensure the Intelligent Flight Battery has at least 50 power and there is at least 100MB of free s
17. the sensors on the Vision Positioning system Inspire 1 can perform precision hovering even when no GPS is available 16 2014 DJI All Rights Reserved INSPIRE 1 User Manual Follow the steps below to use Vision Positioning 1 Toggle the switch to P as shown the figure to the right 2 Place the Inspire 1 on a flat surface Notice that the Vision Positioning system cannot work properly on surfaces without pattern variations 3 Power on the Inspire 1 The aircraft status indicator will flash twice in green light which indicates the Vision Positioning system is ready Gently push the throttle up to lift off and the Inspire 1 will hover in place N The performance of your Inspire 1 s Vision Positioning System is subject to the surface you are flying over The ultrasonic waves may not be able to accurately measure the distance over sound absorbing materials and the camera may not function correctly in suboptimal environments The aircraft will switch from P mode to A mode automatically if both GPS and Vision Positioning System are not available So operate the aircraft cautiously when in any of the following situations e Flying over monochrome surfaces e g pure black pure white pure red pure green e Flying over a highly reflective surfaces Flying at high speeds over 8m s e Flying over water or transparent surfaces e Flying over moving surfaces or objects e Flying in an area where th
18. uses 3510 motors and 1345 propellers 2014 Dul All Rights Reserved Appendix 2014 DJI All Rights Reserved 55 xipueddy Appendix Specifications Aircraft Model T600 Weight Battery Included 2935 9 Vertical 0 5 m Hovering Accuracy P Mode Max Angular Velocity Max Tilt Angle Max Ascent Speed Max Descent Speed Max Speed Max Flight Altitude Max Wind Speed Resistance Max Flight Time Motor Model Propeller Model Indoor Hovering Operating Temperature Range Diagonal Distance Dimensions Gimbal Model Output Power With Camera Operating Current Angular Vibration Range Mounting Controllable Range Mechanical Range Max Controllable Speed 56 2014 DJI All Rights Reserved Horizontal 2 5 m Pitch 300 s Yaw 150 s 35 5 m s 4 m s 22 m s ATTI mode no wind 4500 m 10 m s Approximately 18 minutes DJI 3510 DJI 1345 Enabled by default 10 to 40 C 559 to 581 mm 438x451x301 mm ZENMUSE X3 Static 9 W In Motion 11 W Station 750 mA Motion 900 mA 0 03 Detachable Pitch 90 to 30 Pan 320 Pitch 125 to 45 Pan 330 Pitch 120 s Pan 180 s Camera Name Model Total Pixels Effective Pixels Image Max Size ISO Range FOV Field Of View CMOS Lens Still Photography Modes HD Video Recording Modes Max Bitrate Of Video Storage Supported File Formats Supported SD Card Types Operating Temperature Rang
19. video then press again to stop recording Controlling Aircraft This section explains how to use the various features of the remote controller The Remote Controller is set to Mode 2 by default 2014 Dul All Rights Reserved 25 SJ9 OJ UO2 S OWSY SJ9 OJ1UO2 2JOWOH INSPIRE 1 User Manual Stick Neutral mid point Control sticks of the Remote Controller are placed at the central position Move the Stick The control stick is pushed away from the central position Remote Controller Aircraft Mode 2 indicates nose direction Remarks Moving the left stick up and down changes the aircraft s elevation Push the stick up to ascend and down to descend Push the throttle stick up to takeoff When both sticks are centered the Inspire 1 will hover in place The more the stick is pushed away from the center position the faster the Inspire 1 will change elevation Always push the stick gently to prevent sudden and unexpected elevation changes Moving the left stick to the left or right controls the rudder and rotation of the aircraft Push the sick left to rotate the aircraft counter clock wise and push the stick right to rotate the aircraft clockwise If the stick is centered the Inspire 1 will stay facing its current direction The more the stick is pushed away from the center position the faster the Inspire 1 will rotate
20. 1 when it is powered on Camera Data Port Power on the Inspire 1 and then connect a USB cable to the Camera Data Port to download photos or videos from the camera to your computer N Power on the aircraft before attempting to download the files 2014 DJI All Rights Reserved 95 SW pue equip SUB pue equip INSPIRE 1 User Manual Camera Operation Use the Shutter and Record button on the remote controller to shoot the images or the videos through the DJI Pilot app For more information about how to use these buttons refer to Controlling Camera P25 ND Filter Attach an ND filter to the front of the camera to reduce over exposure and jello effect Gimbal Gimbal Profile The 3 axis Gimbal provides a steady platform for the attached camera allowing you to capture stabilized images and video The Gimbal can tilt the camera up to 125 degrees and rotate it 360 degrees Z i 0 Use the gimbal dial on the remote controller to control pitch movement of the camera by default Note that you cannot control the pan motion of the camera by default Enable the Master and Slave mode and set the remote controller to Slave state if you wish to control both the pan and pitch movement
21. INSPIRE 1 User Manual 2014 12 ciji Using this manual Legends Warning Important Xx Hints and Tips Heference Before Flight The following tutorials and manuals have been produced to ensure you to make full use of your Inspire 1 1 Disclaimer 2 In the Box 3 Inspire 1 Quick Start Guide 4 Safety Guidelines 5 Inspire 1 User Manual 6 Intelligent Flight Battery Safety Guidelines Watching all the tutorial videos and reading the Disclaimer before flight is recommended Afterwards prepare for your first flight by using the Inspire 1 Quick Start Guide Refer to this manual for more comprehensive information Watch the video tutorials Please watch the tutorial video below to learn how to use Inspire 1 correctly and safely www dji com product inspire 1 video Download the DJI Pilot app Download and install the DJI Pilot app before use Scan the QR code or visit m 73 n http m dji net djipilot to download the app THEN Hs For the best experience use mobile device with Andriod V 4 1 2 or above iOS version is coming soon Contents Using this manual Legends Before Flight Watch the video tutorials Download the Dul Pilot app Product Profile Introduction Feature Highlights Assemble the Aircraft Aircraft Diagram Remote Controller Diagram Aircraft Flight Controller Flight Mode Flight Status Indicator Return to Home RTH Smart RTH Low Battery RTH Failsafe RTH Dynamic Hom
22. TH Failsafe RTH is activated automatically if remote controller signal including video relay signal is lost for more than 3 seconds provided that Home Point has been successfully recorded and compass is working normally Return home process may be interrupted and the operator can regain control over the aircraft if a remote controller signal is resumed Failsafe Illustration 1 Record Home Point HP 2 Confirm Home Point 3 Remote Controller Signal Lost E Blinking Green Blinking Green Fast Blinking Yellow 4 Signal Lost Lasts 3secs amp o 5 Go Home 20m can be set TT Height over HP lt 20m 6 Landing after Hovering 15secs Fast Blinking Yellow Fast Blinking Yellow Fast Blinking Yellow N Aircraft cannot avoid obstruction during the Failsafe RTH therefore it is important to set an reasonable Failsafe altitude before each flight Launch the DJI Pilot app and enter Camera view and select MODE to set the Failsafe altitude Dynamic Home Point Dynamic home point is useful in situations when you are in motion and require a Home Point that is different from the takeoff point GPS module is located at the position shown in the figure below Z Ensure the space above the GPS module is not obstructed when using Dynamic Home Point 2014 DJI All Ri
23. an find info on the simulation application that plugs into the trainer port Can you suggest a simulation program There is no trainer port on the remote controller for the Inspire 1 10 Can the mobile device holder be used on the Phantom 2 series remote controller 11 No it cannot The mobile device holder can only be used with the Inspire 1 remote The app can be used on the iPad so can it be used on the iPod or iPhone Can it be used on Android tablets or Android phones It is recommended that you use a tablet for the best experience but the following devices have been tested and run the app iOS The following running iOS v7 1 or later iPhone 6 Plus iPhone 6 iPhone 5S iPhone 5C iPhone 5 iPad Air 2 iPad Mini 3iPad Air iPad Mini 2iPad 4th generation Android The following running Android v4 1 2 or later Samsung Note 4 Samsung S5 Sony Z3 XPERIA Samsung Note 3 12 Does the Inspire 1 have a SD card included The Inspire 1 comes with a 16GB micro SD card It supports SD cards up to 64GB 13 Can upgrade and buy a second remote controller if only buy a single remote controller now Yes 14 How big is the Inspire 1 Its length x height x width dimensions without the propellers attached are 44 x 30 x 45cm 17 3 x 11 8 x 17 7in 15 What flight controller does the Inspire 1 use The Inspire 1 uses its own new flight controller 16 Which motors and propellers does the Inspire 1 come with 54 The Inspire 1
24. ce by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help IC RSS warning This device complies with Industry Canada licence exempt RSS standard s Operation is subject to the following two conditions 1 this device may not cause interference and 2 this device must accept any interference including interference that may cause undesired operation of the device Le pr sent areil est conforme aux CNR d Industrie Canada licables aux areils radio exempts de licence L exploitation est autoris e aux deux conditions suivantes 1 l areil ne doit pas produire de brouillage et 2 l utilisateur de l areil doit accepter tout brouillage radio lectrique subi m me si le brouillage est susceptible d en compromettre le fonctionnement IC Radiation Exposure Statement This equipment complies with IC RF radiation exposure limits set forth for an uncontrolled environment This transmitter must not be co located or operating in conjunction with any other antenna or transmitter This equipment should be installed and operated with minimum distance 20cm between the radiator amp your bogy Any Changes or modifications not expressly roved by the party responsible for compliance
25. d 19npoJd INSPIRE 1 User Manual 6 Battery Level LEDs Displays the current battery level 7 Status LED Displays the power status 10 Camera Settings Dial Turn the dial to adjust camera settings Only functions when the remote controller is connected to a mobile device running the DJI Pilot app 11 Playback Button Playback the captured images or videos 12 Shutter Button Press to take a photo If in burst mode the set number of photos will be taken with one press 13 Flight Mode Switch Used to switch between P A and F mode 14 Video Recording Button Press to start recording video Press again to stop recording 15 Gimbal Dial Use this dial to control the tilt of the gimbal 16 Micro USB Port For connecting the remote controller to your computer 17 Mini HDMI Port Connect an HD compatible monitor to this port to get a live HD video preview of what the camera sees 10 2014 Dul All Rights Reserved 8 Power Button Used to power on or power off the remote controller 9 RTH LED Circular LED around the RTH button displays RTH status 16 17 18 19 pause 15 Jd 14 11 13 12 n n ico 18 CAN Bus Port Heserved for future use 19 USB Port Connect to mobile device to access all of the DJI Pilot app controls and features 20
26. de In Dual Controllers mode the Master remote controller operator controls the orientation of the aircraft while the Slave remote controller controls the movement of the gimbal and camera operation I EUBIS o pIA BUBIS eJeule2 pue oap A lt Maste Remote Controller JEUBIS 08pIA Slave Remote Controller 2014 Dul All Rig c hts Reserved 29 SJ9 OJ UO2 S OWSY SJ9 OJ1UO2 2JOWOH INSPIRE 1 User Manual N Use the gimbal dial on the remote controller to control the pitch movement of the camera in the single remote controller mode however you cannot control the pan movement of the camera Setting Up Dual Remote Controllers Mode Dual Remote Controllers mode is disabled by default Users must enable this feature on the Master remote controller by through the DJI Pilot app Follow the steps below for setup Master Remote Controller 1 Connect the remote controller to your mobile device and launch the DJI Pilot app 2 Goto the Camera page and tap q to enter the remote controller settings window 3 Tap Set RC Status to enable Master and Slave mode 4 Select Master in the Set RC Status section to set the remote controller as Master remote controller RC Settings RC Control Settings Master and Slave Set RC Status OFF Master RC Name T12254 Connection Password 1234 Slave RC List 5 Enter the connection pass
27. e If you are between the Restricted l altitude flight IE TIGE ed H A eee but P ane of 1 5 mile and 5 mile ae mode activates it will descend radius to a safe altitude and hover 15 Warning You are in a restricted feet below the safe altitude zone Max flight height restricted to between 10 5m and 120m Fly Cautiously Warning zone No flight restriction applies but Warning You are approaching a there will be warning message restricted zone Fly Cautiously Free zone 7 No restrictions None None Semi automatic descent All stick commands are available except the throttle stick command during the descent and landing process Motors will stop automatically after landing e When flying in the safety zone aircraft status indicator will blink red quickly and continue for 3 seconds then switch to indicate current flying status and continue for 5 seconds at which point it will switch back to red blinking For safety reasons please do not fly close to airports highways railway stations railway lines City centers and other special areas Try to ensure the aircraft is visible Preflight Checklist Propellers are mounted correctly and firmly Micro SD card has been inserted if necessary Gimbal is functioning as normal Motors can start and are functioning as normal DJI Pilot app connected to the aircraft Oat WD Calibrating the Compass Remote controller aircraft battery and mobile de
28. e Remote Controller Name Operating Frequency Transmitting Distance EIRP Video Output Port Power Supply Charging Dual User Capability Mobile Device Holder Output Power INSPIRE 1 User Manual X3 FC350 12 76M 12 4M 4000x3000 100 3200 94 Sony EXMOR 1 2 3 f 2 8 20 mm equivalent 9 Elements in 9 groups Anti distortion Single shoot Burst shooting BURST 3 5 7 frames AEB 3 or 5 bracketed frames at 0 7EV Bias Time lapse UHD 4K 4096x2160p24 25 3840x2160p24 25 30 FHD 1920x1080p24 25 30 48 50 60 HD 1280x720p24 25 30 48 50 60 60 Mbps FAT32 exFAT Photo JPEG DNG Video MP4 MOV MPEG 4 AVC H 264 SD SDHC SDXC Micro SD Max capacity 64 GB Speed UHS 1 or higher 0 to 40 C C1 922 MHz 927 7 MHz Japan Only 5 728 5 850 GHz 2 400 2 483 GHz 2 km Outdoor And Unobstructed 10dBm 900m 13dBm 5 8G 20dBm 2 4G USB Mini HDMI Built in battery DJI charger Host and Slave connection Tablet or Smart Phone 9 W xipueddy xipueddy INSPIRE 1 User Manual Operating Temperature Range Storage Temperature Range Charging Temperature Range Battery Charger Model Voltage Rated Power Battery Standard Name Model Capacity Voltage Battery Type Energy Net Weight Operating Temperature Range Storage Temperature Range Charging Temperature Range Max Charging Power Battery Optional Name Model Capacity Voltage Battery Type Energy Net Weight Operat
29. e Point Vision Positioning System Flight Recorder Attaching and Detaching the Propellers DJI Intelligent Flight Battery Remote Controllers Remote Controller Profile Remote Controller Operations Dual Remote Controllers Mode Remote Controller Status LED Linking the Remote Controller Remote Controller Compliance Version Gimbal and Camera Camera Profile Gimbal m m m N ON Oo Oo 12 12 13 13 14 15 15 16 17 17 18 24 24 29 31 32 33 35 36 DJI Pilot App Flight FAQ Camera Map Academy User Center Flight Environment Requirements Flight Limits and Flight Restriction Area Preflight Checklist Calibrating the Compass Auto Take off and Auto Landing Starting Stopping the Motors Flight Test Appendix Specifications Intelligent Orientation Control IOC Firmware Updates FCC Compliance 40 43 43 43 45 45 49 49 50 51 51 56 59 60 61 Product Profile This chapter describes the features of Inspire 1 instructs you to assemble the aircraft and explains the components on the aircraft and remote controllers 2014 DJI All Rights Reserved 5 e jo4d 19npoJd Product Profile Introduction The Inspire 1 is brand new quadcopter capable of capturing 4K video and transmitting an HD video signal up to 2km to multiple devices straight out of the box Equipped with retractable landing gear it can capture an unobstructed 360 degree view from its camera The built
30. e lighting changes frequently or drastically Flying over extremely dark lux lt 10 or bright lux gt 100 000 surfaces e Flying over surfaces that can absorb sound waves e g thick carpet e Flying over surfaces without clear patterns or texture e Flying over surfaces with identical repeating patterns or textures e g tiles with same design Flying over inclined surfaces that will deflect sound waves away from the aircraft Xx e Keep the sensors clean at all times Dirt or other debris may adversely affect the effectiveness of the sensors The effective hovering altitudes of the aircraft is from O to 2 5 meters e Vision Positioning system may not function properly when the aircraft is flying over water e Vision Positioning system may not be able to recognize pattern on the ground in low light conditions less than 100lux Do not use other ultrasonic devices with frequency of 40 KHz when Vision Positioning system is in operation e Vision Positioning system may not be able to stabilize the aircraft when flying close to the ground below 0 5 meters in fast speed Keep the animals away from the aircraft when Vision Positioning system is activated The sonar sensor emits high frequency sound that is only audible to some animals Flight Recorder Flight data is automatically recorded to the SD card This includes flight duration orientation distance aircraft status information speed and other paramet
31. e table below contains details on these indicators RTH LED Status LED SJ9 OJ UO2 S OWSY SJ9 OJ1UO2 2JOWOH INSPIRE 1 User Manual Status LED Alarm Remote Controller Status B Solid Red Nene The remo conironer set as Master but it is not connected with the aircraft m The remote controller set as Master and it is connected G Solid Green None l with the aircraft yi The remote controller set as Slave but it is not PX Solid Purple None connected with the aircraft a l The remote controller set as Slave and it is connected B Solid Blue None with the aircraft Rees Slow Blinking Red B B B Remote controller error BOYER Red and Green Red and None HD Downlink is disrupted Yellow Alternate Blinks RTH LED Sound Remote Controller Status Be Sending Return to Home command to the aircraft WE Blinking White BB Aircraft Return to Home in progress W Solid White BBB BB Aircraft is returning home N The Remote Status Indicator will blink red sound an alert when the battery level is critically low Linking the Remote Controller The remote controller is linked to your aircraft before delivery Linking is only required when using a new remote controller for the first time Follow these steps to link a new remote controller 1 Power on the remote controller and connect to the mobile device Launch Dul Pilot app 2 Power on the Intelligent Flight Battery
32. ed on the propeller itself N Check that the propellers and motors are installed correctly and firmly before every flight Ensure that all propellers are in good condition before each flight DO NOT use old chipped or broken propellers Toavoid injury STAND CLEAR of and DO NOT touch propellers or motors when they are spinning ONLY use original DJI propellers for a better and safer flight experience DJI Intelligent Flight Battery The DJI Intelligent Flight Battery has a capacity of 4500mAh voltage of 22 2V and smart charge discharge functionality It can only be charged with an appropriate DJI approved charger Charger Su ER TORRE 18 2014 Dul All Rights Reserved INSPIRE 1 User Manual N Battery must be fully charged before using it for the first time Refer to Charging the Intelligent Flight Battery P21 for more information DJI Intelligent Flight Battery Functions a 2 3 9 Battery Level Display LEDs display the current battery level Battery Life Display LEDs display the current battery power cycle Auto discharging Function The battery automatically discharges to below 65 of total power when it is idle for more than 10 days to prevent swelling It takes around 2 days to discharge the battery to 6526 It is normal to feel moderate heat emitting from the battery during the discharge process Discharge thresholds can be set in the DJI Pilot app Balanced Charging Automatical
33. ers Attaching and Detaching the Propellers Use only DJI approved propellers with your Inspire 1 The grey or black nut on the propeller indicates the rotation direction of the propeller and where it should be attached To attach the propellers properly match the nut with the dots on the motors of your Inspire 1 2014 DJI All Rights Reserved 17 1e49JlV 1e49JlV INSPIRE 1 User Manual Propellers Grey cap 1345 Black cap 1345R Figure p KC Attach On Motors without a black dot Motors with a black dot a Lock Turn the propellers in the indicated direction to mount and tighten Legends eae Tu g a Unlock Turn the propellers in the indicated direction to loosen and remove Attaching the Propellers 1 Attach the propellers with a grey nut onto a motor without a black dot and spin the propellers clockwise to secure them in place Attach the propellers with a black nut onto a motor with a black dot and spin the propellers counter clockwise to secure its position Be sure to completely tighten each propeller by hand before flight o S voor N Ensure propellers are attached to its corresponding motors otherwise the aircraft cannot take off e Handling the propellers with care e Manually tightent each of the propellers on the corresponding motors to ensure it is attached firmly Detaching the Propellers Hold the motor still Then spin the propeller in the unlock direction indicat
34. ghts Reserved 15 1e49JlV 1e49JlV INSPIRE 1 User Manual There are two options for Dynamic Home Point 1 Set the aircraft current coordinate as the new Home Point 2 Set the remote controller s coordinate as the new Home Point Setting Up Dynamic Home Point Follow the steps below to setup Dynamic Home Point 1 Connect to the mobile device and launch the DJI Pilot app and go to the Camera page 2 Tap and select g to reset the remote controller s coordinates as the new Home Point 3 Tap and select g to reset the aircraft s coordinates as the new Home Point 4 The aircraft status indicator blinks green to show Home Point is set succesfully Vision Positioning System DJI Vision Positioning is a positioning system that uses ultrasonic and image data to help the aircraft identify its current position With the help of Vision Positioning your Inspire 1 can hover in place more precisely and fly indoors or in other environments where there is no GPS signal available The main components of DJI Vision Positioning are located on the bottom of your Inspire 1 including 1 two sonar sensors and 2 one monocular camera Oz ei e Valle Using Vision Positioning Vision Positioning is activated automatically when the Inspire 1 is powered on No manual action is required Vision Positioning is typically used in the indoor environment where no GPS is available By using
35. ht Battery is fully charged when Battery Level Indicators are all off 5 Air cool the Intelligent Flight Battery after each flight Allow its temperature to drop to room temperature before storing it for an extended period IN N Do not charge the Intelligent Flight Battery and remote controller with standard charger model A14 100P1A at the same time otherwise the charger may overheat Always turn off the battery before inserting it or removing it from the Inspire 1 Never insert or remove a battery when it is powered on IN o Power Outlet Intelligent Flight Battery Charger 2014 DJI All Rights Reserved 21 1e49JlV 1eJ9JlV INSPIRE 1 User Manual Battery Level Indicators while Charging LED1 X Np vd ae Men LED2 A AXE A LED3 LED4 lt lt lt lt zx x lt lt lt lt Battery Level 0 25 25 50 50 75 75 100 Fully Charged Charging Protection LED Display The table below shows battery protection mechanisms and corresponding LED patterns Battery Level Indicators while Charging LED1 lt A LA AA LED2 lt lt 1 Da A Be LED3 lt E PS Bs LED4 lt S e dz 2 2 z amp VES as Blinking Pattern LED2 blinks twice per second LED blinks three times per second LEDS blinks twice per second LED3 blinks three times per second LEDA blinks twice per second
36. in camera has an integrated gimbal to maximize stability and weight efficiency while minimizing space When no GPS signal is available Vision Positioning technology provides hovering precision Feature Highlights Camera and Gimbal Up to 4K video recording and 12 megapixel photo capture Reserved mounting space for ND filters for better exposure control New quick release mount allows you to remove the camera with ease HD Video Downlink Low latency HD downlink powered by an enhanced version of the DJI Lightbridge System It also provides dual controllers mode Landing gear Retractable landing gear that enables an unobstructed panoramic view from the camera DJI Intelligent Flight Battery 4500 mAh DJI Intelligent Flight Battery employs new battery cells and a battery management system Flight Controller The next generation flight controller system provides a more reliable flight experience A new flight recorder stores the flight data from each flight and Vision Positioning enhances hovering precision when no GPS is available 6 2014 DJI All Rights Reserved INSPIRE 1 User Manual Assemble the Aircraft Unlocking Travel Mode The aircraft is in Travel Mode during delivery Follow these steps to change it to Landing Mode before your first flight 1 Insert the Intelligent Flight Battery into the battery compartment 2 Power on the Remote Controller and the Intelligent Flight Battery 3 Toggle the Transformation Switch up
37. ing Temperature Range Storage Temperature Range Charging Temperature Range Max Charging Power Vision Positioning Velocity Range 58 2014 Dul All Rights Reserved 10 to 40 C Less than 3 months 20 to 45 C More than 3 months 22 to 28 C 0 40 C 6000 mAh LiPo 2S A14 100P1A 26 3 V 100 W Intelligent Flight Battery TB47 4500 mAh 22 2 V LiPo 6S High voltage battery 99 9 Wh 570g 10 to 40 C Less than 3 months 20 to 45 C More than 3 months 22 C to 28 C 0 to 40 C 180 W Intelligent Flight Battery TB48 5700 mAh 22 8 V LiPo 6S 129 96 Wh 670 g 10 to 40 C Less than 3 months 20 to 45 C More than 3 months 22 to 28 C 0 to 40 C 180 W Below 8 m s 2 m above ground INSPIRE 1 User Manual Altitude Range 5 500 cm Operating Environment Brightly lit lux gt 15 patterned surfaces Operating Range 0 300 cm DJI Pilot App Mobile Device System Requirements iOS version 7 1 or later Android version 4 1 2 or later iPhone 6 Plus iPhone 6 iPhone 5 iPhone 5C iPhone 5 iPad Air 2 iPad Mini 3 iPad Air iPad Mini 2 iPad 4 Supported Mobile Devices Samsung Note 4 Samsung Note 3 Samsung S5 Sony Z3 EXPERIA Note It is recommended that you use a tablet for the best experience Intelligent Orientation Control IOC IOC allows users to lock the orientation of aircraft in different fashions There are three working modes for IOC and you may select
38. ing both are available and the aircraft is using GPS for positioning P OPTI Vision Positioning is available but the GPS signal is not Aircraft is using only Vision Positioning for hovering P ATTI Neither GPS or Vision Positioning available aircraft is using only its barometer for positioning so only altitude is controlled Amode Attitude GPS and Vision Positioning System is not used for stabilization The aircraft only uses its barometer to stabilize The aircraft can automatically return home if Remote Controller signal is lost if the Home Point is recorded successfully F mode Function Intelligent Orientation Control IOC is activated in this mode For more information about IOC refer to the IOC in Appendix Transformation Switch RTH Button The Transformation Switch RTH Button combination serves two functions Toggle the switch up or down to raise or lower the landing gear Or press the button to activate the Return to Home RTH procedure Transformation Switch This switch has two positions The effect of toggling the switch to any of these positions is defined below Qs y Lower Raise 1 Raise Raise the landing gear to its upper most position 2014 DJI All Rights Reserved 27 SJ9 OJ UO2 S OWSY SJ9 OJ UO2 2JOWOH INSPIRE 1 User Manual 2 Lower The landing gear will lower to its lowest position for landing N Do not raise the landing gear when the aircraft is on the ground Ensure the landi
39. ipment This device complies with part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation FCC Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment This equipment should be installed and operated with minimum distance 20cm between the radiator amp your body This transmitter must not be co located or operating in conjunction with any other antenna or transmitter Note This equipment has been tested and found to comply with the limits for a Class B digital device 2014 DJI All Rights Reserved 61 xipueddy xipueddy INSPIRE 1 User Manual pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interferen
40. ither GPS or Vision Positioning available aircraft is using only its barometer for positioning so only altitude is controlled A mode Attitude GPS and Vision Positioning System is not used for stabilization The aircraft only uses its barometer to stabilize The aircraft can automatically return home if Remote Controller signal is lost if the Home Point is recorded successfully F mode Function Intelligent Orientation Control IOC is activated in this mode For more information about IOC refer to the IOC in Appendix 0 Use the Flight Controller mode switch to change the flight mode of the aircraft refer to the Flight Mode Switch on P27 for more information Flight Status Indicator The INSPIRE 1 comes with the Front LED Rear LED and Aircraft Status Indicator The positions of these LEDs are shown in the figure below Aircraft Status Indicator Front LED Rear LED The Front and Rear LED show the orientation of the aircraft The Front LED displays solid red and the Rear LED displays solid green Aircraft Status Indicator shows the system status of the flight controller Refer to the table below for more information about the Aircraft Status Indicator 12 2014 DJI All Rights Reserved INSPIRE 1 User Manual Aircraft Status Indicator Description Normal RG Y ves Red Green and Yellow Flash Poweronandeatcheck Alternatively GY Green and Yellow Flash Alternatively Ai
41. ly balances the voltage of each battery cell when charging Over charge Protection Charging automatically stops when the battery is fully charged Temperature Detection The battery will only charge when the temperature is between 0 C 32 F and 40 C 104 F Over Current Protection Battery stops charging when high amperage more than 10A is detected Over Discharge Protection Discharging automatically stops when the battery voltage reaches 18V to prevent over discharge damage ohort Circuit Protection Automatically cuts the power supply when a short circuit is detected 10 Battery Cell Damages Protection DJI Pilot app shows warning message when damaged battery cell is detected 11 Battery Error History Browse the battery error history from the DJI Pilot app 12 Sleep Mode Sleep mode is entered after 10 minutes of inactivity to save power 13 Communication Battery voltage capacity current and other relevant information is provided to the aircrafts to the main controller N Refer to Disclaimer and Intelligent Flight Battery Safety Guidelins before use Users take full responsibility for all operations and usage Using the Battery Power Button LEDA Bulit in LED LED3 LED pos LED Powering ON OFF Powering On Press the Power Button once then press again and hold for 2 seconds to power on The Power LED will turn red and the Battery Level Indicators will display
42. ndicator Flight height restricted to Warning Height limit N E 120m and under reached joue Max Radius No limits N lf you fly out of the limit you can still control the Inspire 1 but cannot fly it further e f the Inspire 1 flies out of the max radius in Ready to Fly non GPS mode it will fly back within range automatically Flight Restriction of Restricted Areas Restricted areas include airports worldwide All restricted areas are listed on the DJI official website at http www dji com fly safe category mc Restricted areas are divided into category A and category B Category A areas cover major international airoort such as LAX and Heathrow while category B areas includes smaller airports Category A Safety Zone 1 The category A safety zone is comprised of a small no fly zone and a range of restricted altitude zones Flight is prevented in the no fly zone but can continue with height restrictions in the restricted altitude zone 2 1 5 miles 2 4 km around a designated safety zone is a no fly zone inside which takeoff is prevented 3 1 5 miles 2 4 km to 5 miles 8 km around restricted areas are altitude restricted with maximum altitude going from 35 feet 10 5 m at 1 5 miles 2 4 km to 400 feet 120 m at 5 miles 8 km 4 A warning zone has been set around the safety zone When you fly within 320 feet 100m of the safety zone a warning message will appear on the DJI Pilot A
43. ng gear is lowered before landing RTH button Press and hold this button to start the Return to Home RTH procedure The LED around the RTH Button will blink white to indicate the aircraft is entering RTH mode The aircraft will then return to the last recorded Home Point Press this button again to cancel the RTH procedure and regain the control of the aircraft L JI Connecting Mobile Device Tilt the Mobile Device Holder to the desired position Press the button on the side of the Mobile Device Holder to release the clamp and then place your mobile device into the clamp Adjust the clamp to secure your mobile device Then connect your mobile device to the remote controller with a USB cable Plug one end of the cable into your mobile device and the other end into the USB port on the back of the remote controller 28 2014 Dul All Rights Reserved Optimal Transmission Range INSPIRE 1 User Manual The signal transmission between aircraft and remote controller perform best within the range that displayed in the picture shown below Optimal Transmission Range Ensure the aircraft is flying within the optimal transmission range Adjust the distance and position between the operator and the aircraft to achieve optimal transmission performance Dual Remote Controllers Mode More than one remote controller can connect to the same aircraft in Dual Remote Controller mo
44. nnot control the orientation of the aircraft Reset the remote controller to Master in DJI Pilot app if you wish to link the remote controller to the aircraft Remote controller will disconnect from the linked aircraft if a new remote controller is linked to the same aircraft Hemote Controller Compliance Version The remote controller is compliant with both CE and FCC requirements 33 SJ9 OJ UO2 S OWSY Gimbal and Camera This chapter provides the technical specifications of the camera and explains the working mode of the gimbal 34 2014 DJI All Rights Reserved Camera and Gimbal Camera Profile The on board camera supports 4K video capture up to 4096x2160p24 and 12M pixel photos capture by using the 1 2 3 inch CMOS sensor You may export the video in either MOV or MP4 format for editing Available picture shooting modes include burst continuous and timer mode A live preview of what the camera is seeing before you shoot videos and pictures is supported through the Dul Pilot App Camera Micro SD Card Slot To store your photos and videos plug in the micro SD card into the slot shown below before powering on the Inspire 1 The Inspire 1 comes with a 4GB micro SD card and supports up to a 64GB micro SD card A UHS 1 type micro SD card is recommended because the fast read and write capability of these cards enables you to store high resolution video data Donotremove micro SD card from the Inspire
45. of the camera A Use the gimbal dial on the remote controller to control the pitch movement of the camera in the single remote controller mode however you cannot control the pan movement of the camera Pan Control Follow the instructions below to use the gimbal dial to control the pan movement of the gimbal 1 Power on the aircraft and remote control launch Dul Pilot app and enter Camera page 2 Tap RC Control Settings icon and select either C1 or C2 customizable button as the gimbal pitch yaw switching button 3 Select Gimbal Pitch Yaw from the dropdown list 36 2014 DJI All Rights Reserved INSPIRE 1 User Manual RC Control Setting Remote Control Calibration Stick Mode Default stick mode is Mode 2 changing stick modes alters the way the aircraft is controlled Do not change unless familiar with your new mode C1 GimbalPitchYaw C2 Reset gimbal yaw You can customize the C1 and C2 buttons on the back of the remote controller Linking Remote Controller Press C1 or C2 button to switch from pith mode to yaw mode You may use the gimbal dial to pan the gimbal under yaw mode Press C1 or C2 again to exit yaw mode Using DJI Pilot App to Control Gimbal Follow the steps below to use Dul Pilot app to control the gimbal orientation 1 Launch DJI Pilot app enter Camera page 2 Tap and press on the screen until a blue circle is shown 3 Slide to control the gimbal
46. or displays blinking green Follow the steps below to use auto landing 1 Ensure the aircraft is in P mode 2 Check the landing area condition before tapping x to perform landing 3 Aircraft lowers the landing gear and proceed to land automatically Starting Stopping the Motors Starting Motors A Combination Stick Command CSC is used to start the motors instead of simply pushing the stick up Push both sticks to their bottom corners to start the motors Once the motors have spun up release both sticks simultaneously M x Stopping Motors There are two methods to stop the motors Method 1 When the Inspire 1 has landed push the throttle down then conduct CSC Motors will stop immediately Release both sticks once motors stop Method 2 When the aircraft has landed push the throttle down and hold The motors will stop after 3 seconds M K Flight Test Take off Landing Procedures 1 Place the aircraft on open flat ground with battery indicators facing towards you Power on the remote controller and your mobile device then the Intelligent Flight Battery Launch the Dul Pilot App and enter the Camera page Wait until the Aircraft Indicator blinks green This means the Home Point is recorded and it is safe to fly now If it flashes yellow it means Home Point is not recorded and you should not take off Push the throttle up slowly to take off or using Auto Take off to take off ohoot phot
47. orientation within the Camera page as shown below P GPS al KAOFF SafetoFy GPS dul csl 100 amp ISO 100 1 320 EVO 424821 00 22 16 JPEG 4K 30 oO 1 HIHI III 11o H 2M D 39M C E us 88 3 M S 7124 2 ws 37 SW pue equip SW pue equip INSPIRE 1 User Manual Gimbal Operation Modes Three Gimbal operation modes are available Switch between the different operation modes on the Camera page of the DJI Pilot App Note that your mobile device must be connected to the remote controller for changes to take effect Refer to the table below for details Pitch Pan The angle between Gimbal s orientation and aircraft s nose remains constant at all times One user alone can control the pitch motion of the Gimbal but a second user is required to control the pan motion using a second remote controller A Follow Mode The Gimbal will lock to the movements of the aircraft to provide a First MK FPV Mode L Person View flying experience The Gimbal s motion is independent of the aircraft s orientation One user 7 Free Mode alone can control the pitch motion of the Gimbal but a second user is required to control the pan motion using a second remote controller Tap to force the Gimbal orientation to re align with aircraft s orientation W Re alignment by panning from gimbal s curren
48. os and videos using the DJI Pilot app To land hover over a level surface and gently pull down on the throttle slowly to descend After landing execute the CSC command or hold the throttle at its lowest position for 3 seconds or more until the motors stop 9 Turn off the Intelligent Flight Battery first followed by the Remote Controller BR W m CON gO C1 2014 DJI All Rights Reserved 51 16114 16114 INSPIRE 1 User Manual N When the Aircraft Status Indicator blinks yellow rapidly during flight the aircraft has entered Failsafe mode e A low battery level warning is indicated by the Aircraft Status Indicator blinking red slowly or rapidly during flight e Watch video tutorials about flight for more flight information Video Suggestions and Tips Work through the checklist before each flight Select desired gimbal working mode in the DJI Pilot app Aim to shoot when flying in P mode only Always fly in good weather such as sunny or windless days Change camera settings to suit you These include photo format and exposure compensation Perform flight tests to establish flight routes and scenes Push the sticks gently to make aircraft movements stable and smooth NOOR D 52 2014 DJI All Rights Reserved FAQ 2014 DJI All Rights Reserved 53 OVA Troubleshooting FAQ 9 How can put a GoPro camera on the Inspire 1 The Inspire 1 does not currently
49. pace on the SD card Step 2 Prepare the Firmware Update Package 1 Download the firmware update package from the official DJI website http www dji com product inspire 1 2 Insert the SD into your PC Extract the all downloaded file into the root directory of the SD card Hemove the SD card from your PC and insert it into the SD card slot on the Inspire 1 camera Step 3 Update the Aircraft 1 Connect to the mobile device to the remote controller power on the remote controller and launch the DJI Pilot app to obtain the information about firmware update progress Confirm you wish to update within the app to continue Upgrade will begin automatically after power cycling the aircraft if DJI Pilot app is not launched 2 It will take approximately 25 minutes to complete the firmware update The camera will sound a D DD beeping sound to indicate the update is complete with success 3 Check the upgrade status by opening the txt file that is automatically generated after the update The update is successful if the text result successful is in the document Try upgrading the firmware again if the text result failed is found or the gimbal sound a long beep sound Updating the Remote Controller Firmware Step 1 Check Battery and SD Card Capacity Hemote controller firmware is included in the aircraft firmware update package Use the same update package file that is downloaded from the Dul official website Ensure the remote
50. paring Remote Controller Tiltthe Mobile Device Holder to the desired position then adjust the antenna as shown 1 Press the button on the side of the Mobile Device Holder to release the clamp adjust it to fit then attach your mobile device 2 Connect your mobile device to the remote controller with a USB cable 3 Plug one end of the cable into your mobile device and the other end into the USB port on the back of the remote controller 8 2014 Dul All Rights Reserved INSPIRE 1 User Manual Aircraft Diagram 1 GPS 2 Propeller P17 3 Motor 4 Front LED P12 5 Landing gear 6 Gimbal and Camera P37 7 Intelligent Flight Battery P18 8 Aircraft Micro USB Port 9 Rear LED P12 10 Camera Micro USB Port 11 Camera Micro SD Card P35 12 Vision Positioning Sensors P16 13 Aircraft Status Indicator P13 Remote Controller Diagram 1 Antennas P29 Relays aircraft control and video signal 2 Mobile Device Holder Mounting place for your mobile device 2 3 Control Stick Controls aircraft orientation 4 Return Home RTH Button P13 ro Press and hold the button to initiate Return to 8 D EX gt Home RTH 6 5 Transformation Switch P27 Toggle the switch up or down to raise or lower the landing gear 2014 DJI All Rights Reserved 9 2H01d JONPOld e jo4
51. pp S NICA AES MI lI C 20 14 Il All Rinhte Dacarvan 46 W LU 14 DJI AIT nignts mne e INSPIRE 1 User Manual Category A safety zone feet F mH gt e1 5 mile M 320 me 5 mile _ gt No Q zone Restricted altitude Warning zone Free zone flight zone Category B Safety Zone 1 Category B safety zone is comprised of a no fly zone and a warning zone 2 0 6 miles 1 km around the safety zone is a designated no fly zone 3 A warning zone has been set around the safety zone When you fly within 0 6 miles 1Km of this zone a warning will appear on the DJI Pilot App Category B safety zone _ 0 6mile gt lt 0 Gmie No fly zone Warning zone Free zone 2014 DJI All Rights Reserved 47 ju6114 16114 INSPIRE 1 User Manual GPS Signal Strong G Blinking Green Aircraft Zone Restriction DJI Pilot App Prompt Status Indicator Warning You are in a No fly a zone Take off prohibited No fly Zone If the aircraft enters the restricted area in A mode but Warning You are in a No fly P mode activates the aircraft zone automatic landing has will automatically descend to begun If you are within 1 5 mile land then stop its motors after radius landing Warning You are in a restricted VB sess zone Descending to safe Re d flashing If the aircraft enters the altitud
52. rcraft warming up IG Green Flashes Slowly Safe to Fly P mode with GPS and Vision Positioning G X2 Green Flashes Twice Safe to Fly P mode with Vision Positioning but without GPS Yee Yellow Flashes Slowly oafe to Fly A mode but No GPS and Vision Positioning Warning Y Fast Yellow Flashing Remote Controller Signal Lost ree Slow Red Flashing Low Battery Warning RE Fast Red Flashing Critical Low Battery Warning RE Hed Flashing Alternatively IMU Error R Solid Red Critical Error REY ee Red and Yellow Flash Alternatively Compass Calibration Required Heturn to Home RTH The Return to Home RTH brings the aircraft back to the last recorded Home Point There are three cases that will trigger RTH procedure they are Smart RTH Low Battery RTH and Failsafe RTH GPS Description The Home Point is the location at which your aircraft takes off when the GPS signal is strong You can view the GPS signal strength through Home Point 8 ul the GPS icon amp ul If you are using the Dynamic Home Point setting the Home Point will be updated to your current position as you move around and when the Aircraft Status Indicator blinks green Smart RTH Using the RTH button on the remote controller refer to RTH button on P28 for more information or the HTH button in the DJI Pilot app when GPS is available to enables smart RTH The aircraft return to the latest recorded Home Point you may control the
53. s DU Remark ie DJI Pilot app Flight Instructions Warning Indicator Tap Go home to have the aircraft return to the Fly the aircraft Home point and land d back and land The battery automatically or Cancel to Low battery Aircraft status it as soon as power is low mE resume normal flight If no l level warning indicator blinks l possible then Please land the action is taken the aircraft RED slowly stop the motors aircraft will automatically go home nd verias and land after 10 seconds i battery Remote controller will sound an alarm m The DJI Pilot app screen will The aircraft Critical Low The aircraft Aircraft status e l M flash red and aircraft starts to will begin to battery level must land indicator blinks descend Remote controller descend and land warning immediately RED quickly will sound an alarm automatically Estimated ne remaining flight remaining gg N A N A N A based on current flight time battery level 14 2014 DJI All Rights Reserved INSPIRE 1 User Manual Xx When the critical battery level warning activates and the aircraft is descending to land automatically you may push the throttle upward to hover the aircraft and navigate it to a more appropriate location for landing e Color zones and markers on the battery level indicator reflect estimated remaining flight time and are adjusted automatically according to the aircraft s current status Failsafe R
54. should abide by all regulations from such organizations as the ICAO International Civil Aviation Organization FAA and their own national airspace regulations For safety reasons the flight limits function is enabled by default to help users use this product safely and legally The flight limits function includes height limits distance limits and No Fly Zones When operating in P Mode height distance limits and No Fly Zones work together to manage flight In A mode only height limits work and flights cannot go higher than 120 meters Max Height amp Radius Limits Max Height amp Radius limit flying height and distance and the user may change these settings in the DJI Pilot App Once complete your Inspire 1 will fly in a restricted cylinder that is determined by these settings The tables below show the details of these limits Max Height Max Radius ene Home Point V Height of aircraft when powered on 2014 DJI All Rights Reserved 45 16114 16114 INSPIRE 1 User Manual GPS Signal Strong G Blinking Green Flight Limits DJI Pilot App Aircraft Status Indicator Flight altitude must be under Warning Height Max Heigh None SOA the set height limit reached d ON Rapid red flashing 8 h W D Max Radius Flight distance must be within arning Distance ee the max radius limit reached MS max radius limit GPS Signal Weak Y Blinking Yellow Flight Limits DJI Pilot App Aircraft Status I
55. t orientation Pitch angle will remain AM unchanged during the re alignment N Gimbal motor error may occur in these situations 1 Gimbal is placed on uneven ground 2 Gimbal has received an excessive external force e g a collision Please take off from flat open ground and protect the gimbal after powering up e Flying in heavy fog or cloud may make the gimbal wet leading to a temporary failure The gimbal will recover when it dries out 38 2014 DJI All Rights Reserved DJI Pilot App This chapter describes the four main GUI of the DJI Pilot app 2014 DJI All Rights Reserved 39 ddy 10I d Ira DJI Pilot App The DJI Pilot app is a new mobile app designed specifically for the Inspire 1 Use this app to control the gimbal camera and other features of your flight system The app also comes with Map Store a User Center for configuring your aircraft and sharing your content with friends It is recommended that you use a tablet for the best experience United States Mountian View Shot with DJI INSPIRE 1 e 9 CAMERA MAP ACADEMY USER CENTER Camera The Camera page contains a live HD video feed from the Inspire 1 s camera You can also configure various camera parameters from the Camera page 1 2 3 4 5 6 7 8 18 ull PA CL Safe to Fly GPS ell m
56. the current battery level Powering Off Press the Power Button once then press again and hold for 2 seconds to power off 2014 DJI All Rights Reserved 19 1e49JlV 1e49JlV INSPIRE 1 User Manual Low Temperature Notice 1 Battery capacity is significantly reduced when flying in low temperature environment O C 2 t is not recommended to use the battery in extremely low temperature lt 10 C environment Battery voltage should reach to the appropriate level when using in the environment where temperature range between 10 C to 5 C 3 Stop flying when DJI Pilot app displays Low Battery Level Warning in low temperature environment Place the battery indoors to warm up the battery before using it in the low temperature environment 5 To ensure the performance of the battery keep the battery body temperature above 20 C DN N In cold environments insert the battery into the battery compartment and allow the aircraft to warm up for approximately 1 2 minutes before taking off Checking the battery level The Battery Level Indicators display how much remaining power the battery has When the battery is powered off press the Power Button once The Battery Level Indicators will light up to display the current battery level See below for details The Battery Level Indicators will also show the current battery level during charging and discharging The indicators are defined below lt LED is on
57. ul 100 9 ISO 100 1 320 EVO 24821 e 00 22 16 JPEG 4K 30 AE amp nO e 10 e 15 KS OX p 14 H 9 TT 7 ON 7 O a S26 Q A 13 H 2M D 39M g PAS 11 Cs fau 1 2m 200 7 12 40 2014 DJI All Rights Reserved INSPIRE 1 User Manual 1 Flight Mode wove The text next to this icon indicates the current flight mode Tap to enter MC Main Controller settings Modify flight limits perform compass calibration and set the gain values on this screen 2 GPS Signal Strength ull This icon shows the current strength of GPS signals Green bars indicates adequate GPS strength 3 IOC Settings SA CL This icon shows which IOC setting that the aircraft has entered when in F Mode Tap to enter IOC setting menu and select Course Lock Home Lock or Point of Interest Lock 4 System Status Safe to Fly GPS This icon shows current aircraft system status such as GPS signal health 5 Battery Level Indicator o o o The battery level indicator dynamically displays the battery level The color zones on the battery level indicator represent different battery levels 6 Remote Controller Signal g ull This icon shows the strength of remote controller signal 7 HD Video Link Signal Strength ei ilk This icon shows the HD video downlink signal strength between the aircraft and the remote controller 8 Led Battery Level FF 100 This icon sho
58. vice are fully charged INSPIRE 1 User Manual IMPORTANT Make sure to calibrate the compass in every new flight location The compass is very sensitive to electromagnetic interference which can cause abnormal compass data leading to poor flight performance or even failure Regular calibration is required for optimum performance DO NOT calibrate your compass where there is a chance of strong magnetic interference such as magnetite parking structures and steel reinforcements underground DO NOT carry ferromagnetic materials with you during calibration such as keys or cellular phones DO NOT calibrate beside massive metal objects Calibration Procedures Choose an open space to carry out the following procedures 1 Ensure the compass is calibrated If you did not calibrate the compass in the Checklist or if you have changed your position since last calibrating it tap MODE in the app and select Compass Calibration to calibrate the compass Then follow the on screen instructions 2 Hold and rotate the aircraft horizontally 360 degrees and the Aircraft Status Indicator will display a solid green light 2014 Dul All Rights Reserved 49 16114 16114 INSPIRE 1 User Manual 3 Hold the aircraft vertically with nose pointing downward and rotate it 360 degrees around the center axis Recalibrate the compass if the Aircraft Status Indicator show solid red
59. word for the Slave remote controller Slave Remote Controller 1 Tap Search for Master Controller to search the Master remote controller RC Settings RC Control Setting Master and Slave Set RC Status OFF Master RC Name S88642 Request Control Search for Master Controller Master RC List 30 2014 Dul All Rights Reserved INSPIRE 1 User Manual N Remote controller cannot link to the aircraft if the remote controller is set as Slave Meanwhile the Slave remote controller cannot control the orientation of the aircraft Reset the remote con troller to Master in DJI Pilot app if you wish to link the remote controller to the aircraft 2 Search the Master remote controller in the surrounding area in the Request Control section RC Control Settings Master and Slave Set RC Status OFF Master RC Name S88642 Request Control Search for Master Controller Master RC List v 112254 3 Select the Master remote controller from the Master RC List and input the connection password to connect to the desired Master remote controller v 12254 Connection Password Master RC List Remote Controller Status LED The Status LED reflects connection status between Remote Controller and aircraft The RTH LED shows the Return to Home status of the aircraft Th
60. ws the current Intelligent Flight Battery level Tap to enter battery information menu set the various battery warning thresholds and view the battery warning history in this page 9 Led General Settings i9 Tap this icon to enter General Settings page Select parameter units reset the camera enable the quick view feature adjust the gimbal roll value and toggle flight route display on this page 10 Camera Operation Bar Exposure Lock AE Tap to enable or disable the camera exposure lock Shutter Tap this button to take a single photo Press and hold this button to enter camera settings Record e Tap once to start recording video then tap again to stop recording You can also press the Video Recording Button on the remote controller which has the same function 2014 DJI All Rights Reserved 41 ddy 10 Id Ira ddy 10 I d Ira INSPIRE 1 User Manual 11 12 13 14 15 42 Playback gt Tap to enter playback page You can preview photos and videos as soon as they are captured Camera Settings and Shooting Mode cet Tap to enter the Camera Settings page and switch from camera shooting mode from manual to auto Map Display the flight path of the current mission Tap to switch from the Camera GUI to the Map GUI 005 VN o ae Vision Positioning This icon shows the distance between the surface and the Vision Positioning System s sensors LE H
61. y level 2 Then press and hold the Power Button to power on the remote controller 3 The Remote Controller will beep when it powers on The Status LED will blink green slave remote controller blinks solid purple rapidly indicating that the remote controller is linking to the aircraft The otatus LED will show a solid green light when linking is completed 4 Repeat step 2 to power off the remote controller after finish using it Charging Remote Controller Charge the remote controller via supplied charger S NEN ui EN a E Andia PUT AID ahte Baearen 24 V ZU 14 DJI ANT gnis ne a INSPIRE 1 User Manual 11 Power Outlet Charger Power Button Controlling Camera Shoot videos or images and adjust camera settings via the Shutter Button Camera Settings Dial Playback Button and Video Recording Button on the remote control 1 Camera Settings Dial Turn the dial to quickly adjust camera settings such as ISO shutter soeed and aperture without letting go of the remote controller Move the dial button to left or right to view the pictures or videos in playback mode 2 Playback Button Press to view images or videos that have already been captured 3 Shutter Button Press to take a photo If burst mode is activated multiple photos will be taken with a single press 4 Recoding Button Press once to start recording

User Manual - B&H Photo Video Digital Cameras, Photography

Contents

Download Pdf Manuals

Related Search

Related Contents

User Manual - B&amp;H Photo Video Digital Cameras, Photography

Contents

Download Pdf Manuals

Related Search

Related Contents

User Manual - B&H Photo Video Digital Cameras, Photography