USER MANUAL - Joyfay.com
Contents
1. main part main part pai d L bias 32 5 a 38 q j 90 ETEN fix screw 9 lt fix screw a aE a O O table clip wall clip guide rail clip floor prop Vil Assembly and debugging Open the packing box check whether there are missing parts or damage phenomenon of the products according to the product list If there is any problem please contact with the dealer or manufacturer in time to get solved properly 1 Wall hung style check lamp first determine the position of clip size is as shown in picture 2 Using a drill to dig four 10 mm holes with 25 mm depth Plug the wooden stopper into the hole with a hammer fix the hanging fixture with tapping screws Screw out the lock screw on the connecting pin of the lamp insert the connecting pin into the hole and screw down the screws 2 Table clip style check lamp first install the clip picture 3 in desktop or mesa satisfying position lock the fixed screw to make the clip firmed in the desktop or mesa Screw out the lock screw on the connecting pin of the lamp insert the connecting pin into the hole and screw down the screws 3 Guide rail clip style check lamp adjust the bolt to the right size according to the track picture 4 carry forward it into orbit and lock it Screw out the lock screw on the connecting pin of the lamp insert the connecting pin into the hole and screw down the screws 4 Floor prop style check lamp first install _ the chassi2. CO O Content L2Brief IntrOdUGHON e 24 61 24 54550520095 53 wide aT NEEN ll Performance Summarize 006 KD 202C Local examination lamp Ill Main technical parameters U S E R M AN U AL IV Security tips and symbol instructions V Working Environment 4 00 VI Produ ilist H Sa ewww we eee X Failure Judgment and Eliminating Methods XI Replacement of bulbs 00 0005 4 XI After sales service warranty 0005 X IiiTransportation and storage conditions X IV Electrical schematic diagram and components I Brief introduction Model KD 202C Scope of application This product is a local auxiliary check lamp designed for doctors and nurses in diagnosis and treatment process which demand higher for local lighting It is mostly used in outpatient visit and miniature operation occasion Characteristic Small can be bent freely can be used together with wall clip ceiling clip table clip and floor prop wide serviceability Product component Lamp holder hose power box support parts and power cord ll Performance Summarize The check lamp is designed with low voltage cold lighting system and high power LED lighting source safe and reliable Lamp holder has the function of curve transfer and rotating Convenient safe and reliable The design and production of this light source stri
3. brightness adjusting Turn on the power switch the indicator is button is not open bright but the lamp is button to the not bright maximum Flare adjusting ring is Transfer the not open flare adjusting ring to the maximum Contact with the after sale service department for solution Contact with the after sale service department for solution Other fault Contact with the after sale service department for solution Bulb damage System line fault XI Replacement of bulbs The light bulb of this product is LED normal life is of about 50000 hours Generally there is no need to change If there is any fault please inform the manufacturer to get appropriate treatment XII After sales service warranty Warranty of 18 months provide maintenance service all user s life in the warranty period in normally using the trouble because of the product quality the consumer depends onthe warranty slip and invoice enjoys tree maintenance service f the error caused by refitted Ominstall other functions which is without Our company s permission is not within the scope of warranty lithe model number release date is modified deleted moved or unrecognized will not enjoy the maintenance service The error caused by human factor such as falling squeezing dip in wetting etc is not within the scope of warranty Once receiving the goods please sign and accept it after opening the package to inspect and confirm whe
4. ctly executes the first part of the safety requirements of medical elecirical equipment GB4793 1 2007 general requirements which is guaranteed in safety lll Main technical parameters Input voltage 100V 245V 50HZ 60HZ Lamp power 3W SW Input power lt 10W Color temperature OOOK 500K 4500K 500K Fuse protector 2A IV Security tips and symbol instructions 1 When the check lamp is in use you should always abide by the basic safety precautions in order to avoid fire electric shock or the risk of injury 1 Please read the instructions carefully and operating according to the specifications and requirements 2 The replacement of fuse protector should be the same with the mark 2 The introduction of the following symbols Attention Check the random documents 25 Protect the grounding Disconnect the power V Working Environment Connect the power A Environmental temperature 10 C 40 C B Relative humidity lt 75 C The atmosphere 86 0 106 0kPa VI Product list Check lamp one power line one Fixture table clip guide rail clip wall clip O Floor prop fixed floor prop lift floor prop V Product interface 1 Master device of KD 202C D DEDE DE Picturel lock screw connecting pin power switch power box lamp holder Wflare adjusting ring hose indicator light 2 Fixture interface picture2 picture3 picture4 pictured hole for main part 70 A hote for TE hole for f 4
5. s pulley in place then contrapuntal E a connect the base and the strut and the lamp Lock the screw Please operate as the diagram A B C A B E du EA A s TI Install according to the steps above the lamp can work Turn on the power switch the lamp begins to work 5 Debugging a bending the hose you get the right lighting position and angle b debugging the height of the support you can get the right illume height c brightness adjusting knob in picture1 can change the lighting intensity d flare adjusting ring in picture1 can change the spot size IX Note 1 Please pull out the power plug before clean the lamp do not use liquid spray to clean it 2 When install the lamp please assemble and reinforce it according to the instruction of the technical requirements 3 Do not use the lamp near water 4 The maintenance installation commissioning of the lamp should be operated by professional Q2 4 5 Never put any item on the power line 6 The light intensity of illumination is higher you should be cautious in use with your eyes X Failure Judgment and Eliminating Methods It should be operated by the professionals Fault phenomena Turn on the power Power lines have no Connect to the circuit switch the indicator is electricity where there is not bright electricity supply The power cord is not Reconnect the power connected well cord Change the fuse Brightness adjusting Transfer the
6. ther the instrument is crushed scratched or not Make sure there is no special unnumbered inside If the goods are damaged and you did not inspect before sign it It will be at your own risk X IiTransportation and storage conditions A Environmental temperature 40 C 55 C B Relative humidity lt 0 C The atmosphere 50Kpa 106Kpa X IV Electrical schematic diagram and components list Warranty card DBS a 24k 39 Tl SW SPST 2 AC 220VIN Company name Address Phone No ee Product name Serial Manufacture Number date Sale date e Circuit board Remark The warranty of our products is 18 months since the release date Pleasestruthtully fill in this form cut it according to the dotted line and send it back to our company thank you for your cooperation Adjustable OK PW ISSN we nnn nn nnn ene nr rn oe nn ne ne n fo es Maintenance card 10n 400 473 1 630V Power 30W controlled Company name Address Phone No ee Product name Serial Manufacture E Number date Any products may be updated or improved The change of circuit or Sale date element specifications of the product will not with prior notice Fault description 2012 edition Remark You can enjoy seventy percent discount for the maintenance services even if you use this card over the quality assurance period
Download Pdf Manuals
Related Search