SeeTool - Solutions for KNX
Contents
1. Push button 1 Selection of function switch Number of objects two Triggering of status LED rom status feedback object Object A Value OFF telegram Object B Value ON telegram Push button 2 Selection of function switch Number of objects one Triggering of status REDS flashes when switch value obj A not equal to 0 Pushbutton 3 Selection of function blind Direction of movem UP Pushbutton 4 Selection of function blind Direction of movem DOWN gt 1 1 lt 1 1 83 lt 1 1 4 lt 1 1 2 gt 1 1 4 gt 1 1 3 lt 1 1 2 gt 1 1 4 gt 3 1 2 gt 3 1 1 gt 3 1 2 gt 3 1 1 1 1 1 gt 1 1 2 lt 3 1 1 gt 3 1 2 gt Switch actuator REG K 2x230 16 0 Switch object Channel 1 1 bit 3 Status feedback Channel 1 1 bit Device selection Device selection 2 fold switch actuator Channel 1 General Status information Relay state after bus voltage recovery active status resp object opened Blind actuator REG K 2x 10 0 Movement obj in manual mode Channel 1 1 bit 1 Stop Step obj in manual mode Channel 1 1 bit Channel config Channel 1 operation mode blind or roller shutter See description fine tuning 1 Blind only in case of blind How does the existing blind move downwards closed upwards horizontal downwards tilted upwards horizontal downwards closed upwards closed downwards tilt2. actuator REG K At the beginning of the parameter setting you should define which kind of motor driven hangings are used In the configuration of each channel blind or roller shutter can be selected Parameter page Parameter Value Channel config Channel 1 operation mode Blind Roller shutter In the case of the blind configuration additional parameters for the fine tuning of the behavior of the slats are available In the case of roller shutter these parameters are not necessary and can not be selected Application 2 0 1 0 0 4 Movement dependent automatic light control with manual control and blind shutter control Technical specifications Defining blind type only for blind with slats The application differentiates between four types of blind You can determine the blind type from the position of the slats during movement Types 2 or 4 slats are downwards titled should be selected when the slats have a mechanically determined working position The working position restricts the possible opening angle of the slats as long as the blind has not reached its lower end position Blind type 1 without working position Blind type 2 with working position downwards closed upwards horizontal downwards tilted upwards horizontal Blind type 3 without working position Blind type 4 with working position downwards closed upwards closed downwards tilted upward
3. possible angels of the slats depend from the mechanical construction of the blind with slats Components The application consists of one movement detector wall mounted one push button wall mounted one DIN rail switch actuator mounted in the cabinet or close to the room and one DIN rail blind actuator mounted in the cabinet or close to the room MTN647393 KNX Switch actuator REG K 2x230 16 with manual mode MTN649802 KNX Blind actuator REG K 2x 10 with manual mode Application 2 0 1 0 0 4 Movement dependent automatic light control with manual control and blind shutter control Technical specifications Design ranges Frames not included Other designs and colours available EXXACT WDE002933 KNX Push button 2 gang fu n cti ons WDE002959 KNX PIR 180 2 20m flush mounted Installation Movement detector recommended to be installed on the wall at a height of 2 20m Application 2 0 1 0 0 4 FLN Movement dependent automatic light control with manual control and blind shutter control Technical specifications Wiring diagram KNX KNX Push button PIR 180 2 20m 2 gang flush mounted WDE002933 WDE002959 System component Blind control Manual control KNX i Power supply KNX Switch actuator REG K 2x230 16 with manual mode MTN647393 KNX Blind actuator 2 REG K 2x 10 with manual mode MTN649802 things work together Appl
4. A classification needs additional functionality which realises an automatic pulling down of the shutter or blind dependant on the outside temperature and lux value in order to save the room from outside thermal influences This automatism will be controlled by a central control unit central building management function plus a weather station sensing conditions outside the building A description on an exemplary functionality is shown in Appendix 1 SB which will be automatically added to your project s document folder when selecting a solution with shutter blind functionality to your project Power failure behaviour Switch actuator Relay state after bus voltage failure no change relay remains Switch actuator Relay state after bus voltage recovery opened light is OFF Blind actuator Behavior when bus voltage fails no reaction relay remains Blind actuator Behavior on bus voltage recovery stop no movement When you want to set another behavior for the blind actuator you can enable the parameter page failure mode For more detailed information please read the application manual 11 Application 2 0 1 0 0 4 FLN Movement dependent automatic light control with manual control and blind shutter control Technical specifications User manual The user manual provided for the application is an end users training material and can be installed at site when final submission is made Please do no forget to cut out this qui
5. SeeTool Solutions for KNX Office building segment Application 2 0 1 0 0 4 Movement dependent automatic light control with manual control and blind shutter control Schneider Electric Application 2 0 1 0 0 4 ly Movement dependent automatic light control with manual control and blind shutter control Lighting and blind shutter control functions Lighting control functions Application combines two modes automatic and manual At automatic mode the light is automatically switched OFF or ON dependant on people s movement and existing brightness At manual mode the light can be switched permanently OFF or ON The manual ON will start the automatic movement detection Blind Shutter control functions A blind or roller shutter motor with end position can be connected to each channel of the blind actuator The position of the blind s or shutter s height can be adjusted manually by push buttons At slat blinds an adjustment of the slat s angle is possible as well Application areas Lighting The application is defined for single room offices and conference rooms where automatic control is important but manual control required as well e g during presentations It is also usable in all types of non occupied storage rooms and occasionally used rooms as it offers basic control of the lighting with an automatic movement detector and a manual control by push button gt Energy savings gt Flexibility Lights w
6. ck guide for the user and attach to the wall next to the entrance to the room Also make sure the customer is aware of the installed applications function Quick guide This room is equipped with movement dependent automatic light control with manual control and blind shutter control Automatic mode operation Lighting control The light is automatically switched ON when a person enters the room and the brightness value is below a predefined brightness threshold It is automatically switched OFF when no movement is detected in the room and preset delay time has passed The light can also be switched ON independent of brightness by pushing button no 1 Switch OFF delay default time is 25 min The brightness threshold default is 300 lux Manual mode operation Push button no 2 affects a permanent OFF To turn the lights ON again push button no 1 has to be pressed The automatic mode with movement detection will start again After an automatic OFF the brightness dependent switch to ON will start at movement again service for your Schneider y 06 10 Application 2 0 1 0 0 4 amp Electric customer 12 Application 2 0 1 0 0 4 Movement dependent automatic light control with manual control and blind shutter control Technical specifications User manual Quick guide This room is equipped with movement dependent automatic light control with manual control and blind shutter control Automatic mode ope
7. ed upwards closed See description fine tuning Slat position after movement last slat position 1 Drive only in case of blind Time base for running time of height adjustment Factor for running time of height adjustment 10 64000 1 s 1000 ms See description fine tuning Time base for step interval of slat 10 ms Factor for step interval of slat See description fine tuning Time base for running time of slats 10ms Factor for running time of slat See description fine tuning Pause on reverse on change in direction 1 255 factor 100 ms manufacturer s data See description fine tuning 100 ms 1 Drive only in case of roller shutter Time base for running time of height adjustment Factor for running time of height adjustment 10 64000 1 s 1000 ms See description fine tuning Pause on reverse on change in direction 1 255 factor 100 ms manufacturer s data See description fine tuning 100 ms settings Application 2 0 1 0 0 4 Movement dependent automatic light control with manual control and blind shutter control Technical specifications Group addresses Address Name proposal Function WAN Room 001 Light On Off Light on off by the movement detector 1 1 2 Room 001 Light Status Feedback from actuator On Off 1 1 3 Room 001 Light Switch On Brightness independent switch on from push button 1 1 4 Room 001 Ligh
8. he type of blind in use Type 1 slats 100 downwards closed and lower end position closed slats 0 upwards horizontal Type 2 slats 100 downwards tilted mech working pos lower end position closed slats 0 upwards horizontal Type 3 slats 100 downwards closed and lower end position closed slats 0 upwards closed Type 4 slats 100 downwards tilted mech working pos lower end position closed slats 0 upwards closed The opening angle after a movement of type 1 and 3 is directly influenced by the running time of the slats The opening angle after a movement of type 1 and 3 is also influenced by the mechanically determined working position The slats can only move up to the working position e g 75 as long as the lower end position of the height is not reached When this end positions is reached the slats can move up to the maximum value 100 The measuring of the slat running time should be done at this lower end position Parameter page Parameter Value 1 Drive Time basis for running time of slat 10 100 ms 1 Drive Factor for running time of slat 5 255 Slat step interval only for blind with slats Depending on the slat running time the number of steps for opening or closing the slats can be defined The time for one short movement of the slats is called step interval E g slat running time 1 second and step interval 0 1 seconds gt slats can be com
9. ication 2 0 1 0 0 4 Movement dependent automatic light control with manual control and blind shutter control Technical specifications Configuration The ETS tool is used to set the parameters for the devices in the application and to define the functional relationship between the devices by group addresses The following parameters and group address relations must be set and assigned The parameters should be set first and in the described order The parameters which can be changed to fine tune the application are described further on KNX PIR 180 2 20m 0 Switch object1 Block 1 1 bit 7 Trigger object Block 1 1 bit 8 Locking object Block 1 1 bit 109 Status feedback Safety pause 1 bit Block 1 general Operation mode master mode Locking function enable Block 1 general gt Disable function Behaviour at start of block send telegram Block 1 general gt Brightness Brightness threshold 10 2000 Lux 300 Block 1 general gt Times Master triggering is brightness dep disabled Time base for staircase timer 1 min Time factor for staircase timer 1 255 25 KNX Push button 2 gang 0 Switch objectA PB 1 1 bit 1 Switch object B PB 1 1 bit 2 Status feedback obj BBH 1 bit 3 Switch objectA PB2 1 bit 6 Stop Step object PB 3 1 bit T Movement object PB 3 1 bit 9 Stop Step object PB 4 1 bit 10 Movement object PB 4 1 bit General Push button 2 gang
10. ill not remain on all night or even For optimised cost the amount of units is when not needed Energy savings are reduced to a minimum but allows maximum achieved by turning ON and OFF the lights of flexibility when walls are removed and automatically This reduces the time for the rooms are combined lights turned on and can lead to savings of up to 40 compared to installations without automatic function The shutter blind e one functionality can support energy savings gt Rel la bi ity when using as a shield against over heating of rooms at summer daytimes or cooling at Design planning and installation documents winter nighttimes are pre defined which makes the entire building process faster and more reliable EN 15252 User documents and descriptions are A class solution prepared to assist in user training The gt Future proof application works as an individual stand alone room control unit and can be installed The application is prepared and defined for used alone or combined with the entire integration into a Building Management network System if required through the open technology communication network tested amp validated Application 2 0 1 0 0 4 Movement dependent automatic light control with manual control and blind shutter control Technical specifications Functions Lighting control The application has two modes automatic mode and manual mode Automatic mode The light is automatically swi
11. pletely opened in 10 steps Parameter page Parameter Value 1 Drive Time basis for step interval of slat 10 100 ms 1 Drive Factor for step interval of slat 5 255 Pause on reverse for change of direction When the blind actuator moves and receives a command to move to the opposite direction it stops and waits for the pause of reverse interval to pass Caution Pauses on reverse interval that are too short could cause damage to the drive When setting the values observe the manufacturers specification for the drive under all circumstances Parameter page Parameter Value 1 Drive Pause on reverse on change in direction 1 255 factor 100 ms ms fine tuning 10 Application 2 0 1 0 0 4 ly Movement dependent automatic light control with manual control and blind shutter control Technical specifications Additional weather alarm and automatic function Caution When the blinds or other hangings are mounted on the outside of the window the use of automatic weather alarm functions are recommended A weather station is not a part of this room solution and has to be ordered separately We recommend using at least one weather station for each facade with outside mounted blinds For the detailed planning e g thresholds you have to observe the manufacturers specifications for the drive under all circumstances 7 fine tuning This shutter and blind solution is prepared for A class
12. ration Blind shutter control The position of the blind s or shutter s height can be adjusted manually by push buttons With a long pressure on button 3 the blind or roller shutter moves upwards With a long pressure on button 4 the blind or roller shutter moves downwards With a short pressure the movement of the blind or shutter stops In the case of a blind or hanging with slats the angle of the slats can also be moved stepwise with several short pressures With button 4 the slats turn to the position 100 closed or to the mechanically determined working position With button 3 the slats move to the opposite direction The possible angels of the slats depend from the mechanical construction of the blind with slats service for your Schneider y 06 10 Application 2 0 1 0 0 4 amp Electric customer 1SC02071_EN 13
13. s closed Parameter page Parameter Value 1 Blind How does the existing blind move 1 downwards closed upwards horizontal 2 downwards tilted upwards horizontal 3 downwards closed upwards closed 4 downwards tilted upwards closed Caution Some blinds have special drive characteristics which are not congruent with one of the four types of blinds In this case an exact positioning of the slats might be impossible fine tuning Application 2 0 1 0 0 4 ly Movement dependent automatic light control with manual control and blind shutter control Technical specifications Slat position after movement only for blind with slats Parameter page Parameter Value 1 Blind Slat position after movement no reaction operating position last slat position The slat opening that you specify here is inter alia applied after a manual movement command ended by stop fine tun ng telegram This is the standard way of control via long and short pressure with a push button Please note a mechanically determined working position restricts the possible opening angle of the slats as long as the blind has not reached its lower end position Blind types 2 and 4 slats are downwards tilted Recommendation the slat running time should be set When you select slat position after movement last slat position or operating position it is necessary to know the slat running time When you wan
14. t Permanent OFF Auto Permanent OFF 1 Automatic 0 EJAT Room 001 Blind Shutter Up Down Blinds Shutter move downwards or upwards 3 1 2 Room 001 Blinds shutter Stop Blinds Shutters Stop OR Room 001 Blinds shutter Stop Step OR Blinds Stop and Change angel of Slats stepwise settings Application 2 0 1 0 0 4 ty Movement dependent automatic light control with manual control and blind shutter control Technical specifications Fine tuning Some parameters can be changed to fine tune the solution to the building and specific requirements Parameter which may need to be adjusted are listed below our recommendation in brackets KNX PIR 180 2 20m The staircase timer delay time will be retriggered by every detected movement when the light is on The light will be switched off if no movement has been detected within the specified time fine tuning Parameter page Parameter Value Block 1 general gt Times Time base for staircase timer 1s 1h 1 min Block 1 general gt Times Time factor for staircase timer 1 255 25 Delay time Time base x Time factor The light will only be switched ON by movement if the brightness in the room is below the specified brightness threshold Note that the brightness is measured at the installation place of the detector Parameter page Parameter Value Block 1 general gt Brightness threshold 10 2000 lux 300 Brightness Blind
15. t to define the number of steps for opening or closing the slats you also need the running time Height running times The blind actor allows a precise positioning of the height with value objects This positioning depends from the calculation of the running time of the used blinds and shutters As various types of blinds and shutters are available it is not possible to recommend any default value You should measure the height running time from end to end position and set the following values Parameter page Parameter Value 1 Drive Time basis for height running time 10 100 ms 1 Drive Factor for running time 10 64000 1 second 1000 ms The drive needs this period of time to move out of one end position blind roller shutter is fully open or closed into the opposite end position When the set time expires the relay of channel 1 is automatically switched off even if the drive with the values set here has not fully reached its end position If you want to optimize the positioning behavior additional drive parameters can be set Application 2 0 1 0 0 4 Movement dependent automatic light control with manual control and blind shutter control Technical specifications Slat running time only for blind with slats The slat running time is the period of time it takes the slat to complete a full movement from 0 to 100 or vice versa The regulating range through witch the opening angle passes depends on t
16. tched ON when a person enters the room and the brightness value is below a predefined brightness threshold It is automatically switched OFF when no movement is detected in the room and preset delay time has passed The light can also be switched ON independent of functions brightness by pushing button no 1 Delay is adjustable by ETS software Default is 25 min The brightness threshold is also adjustable by ETS software Our recommendation is 300 lux Manual mode Push button no 2 affects a permanent OFF To turn the lights ON again push button no 1 has to be pressed The automatic mode with movement detection will start again After an automatic OFF the brightness dependent switch to ON will start at movement again Blind shutter control A blind or roller shutter motor with end position can be connected to each channel of the blind actuator The position of the blind s or shutter s height can be adjusted manually by push buttons With a long pressure on button 3 the blind or roller shutter moves upwards With a long pressure on button 4 the blind or roller shutter moves downwards With a short pressure the movement of the blind or shutter stops In the case of a blind or hanging with slats the angle of the slats can also be moved stepwise with several short pressures With button 4 the slats turn to the position 100 closed or to the mechanically determined working position With button 3 the slats move to the opposite direction The
Download Pdf Manuals
Related Search