User`s manual
Contents
1. Write to module It loads in the module one of the configurations previously saved in the memory of the programmer The steps to make a correct configuration of the headend are specified below SD Backup Write to module Write to module 1 Read from module CFG 00 2 Write to module Enc Bitrate 7950 Operation finish Virdee Resell 120x576 Output Freq 474000 ETWF310 ETWF310 ETWF310 1 Select the option Write to module 2 Select the position of the CFG 3 A window will appear and it will let through Up Down buttons Press OK memory that you wish to copy in the you know that the configuration made to continue module Please verify that the data of has been correct the selected memory correspond to the channel that you wish to copy 16 ETWF 310 version_en_2 0 FTE maximal User s manual ETWF 310 1 5 Accessories and example of installation Example of installation ANTENNA The installation is formed by 6 TSF 310 and 2 ETWF 310 they will make possible to tune up to 6 different B transponders TSF and moreover the reception of up to 4 base band channels ETWF 310 In both cases QUAFRO PU the channels will be modulated in DVB T and distributed through the installation 9 MUX 310 The distributed channels will need a terrestrial digital f SPS 310 receiver in order to get decoded D Fle a a t Fle F Flo Fle Fs Pte ETWF 310 TSF 310 AT 220 AT 215 the installation we re2. Options Auto or 0 6750 Kbps Video framerate Number of images per second Options 50 60 Video Relation Output Image Relation appearance Options Auto 1 1 4 3 16 9 2 21 71 Video Resolution Output Video Resolution Options 360x576 352x288 176x144 480x576 544x576 720x576 4 ETWF 310 version_en_2 0 FTE maximal User s manual ETWF 310 4 Modulator Set Up This option allows configuring the DVB T DVB H modulator of the device Bandwidth Selection of the Bandwidth of the modulated signal 8MHz 7MHz 6MHz and 5MHz The 5MHz option is only supported by DVB H standard FFT Mode 8K 4K and 2k The 4k option is only supported by DVB H standard Spectrum inversion Activate or deactivate the spectrum reverse in the modulation Guard interval Allows selecting the guard interval of the modulation 1 4 1 8 1 16 and 1 32 FEC Indicates the relationship between the redundant bits and the transmitted information bits 1 2 2 3 3 4 5 6 y 7 8 For example in a FEC 2 3 relation we will find 2 information bits and 1 redundant bit Modulation Output modulation format 4 4 QAM 16 16 QAM 64 64 QAM Advanced settings Mode Selection of the modulation standard DVB T and DVB H codification and modulation In the Attachment you will find all the information related to the resulting useful bit Note The output useful bits rate will depend on the following parameters Bandwidth guard inter
3. Adding services 1 Select Service to add option 2 Select one of the transponder 3 Once you have chosen the services you want to add service select the Add Rem button to include the service in the multiplex Note It is not recommended to exceed the 85 of the maximum capacity of the multiplex due to the possible variability of the bits rate of the inputs services 7 ETWF 310 version_en_2 0 FTE maximal User s manual ETWF Users mama EIWEBtO SE 0 Recomendad capacity lower to 85 Removing services i E 1 Select the Service to remove 2 Select one of the transponder option services you want to remove Remove all services It allows removing all the services included in the multiplex Modify LCN The LCN function allows assigning automatically a predetermined position to each one of the services of the multiplex This function will allow the users who have a receiver with LCN support to make the ordination of channels automatically Note If in the existing installation there are already services that have LNC system you will have to configure the position of the module services in order to avoid conflicts with other net services Bandwidth limitation It allows selecting the of the capacity of the output channel Auto service addition On It selects the services automatically when an input carrier is tuned and when the list of selected services is empty The receiver will
4. ETWF310 1 Select the option Read LOG file 2 A new window will appear It will through Up Down buttons Press OK show the information about the to continue registered events in the module Press the following keys in order to scroll up and down the screen up down Delete LOG file It allows deleting all events stored until this moment Update FW It allows carrying out the firmware update from the programmer Global Update It allows carrying out the update of all the modules that are interconnected at the same time Factory default This option restores the values by default of the module 15 ETWF 310 version_en_2 0 FTE maximal User s manual ETWF 310 3 SD Backup This option allows saving and loading the configuration of the module in the PRO 300 programmer Read from module It stores the current configuration of the module in the memory of the programmer The steps to make a correct reading of the headend are specitied below SD Bac kip Read from module Read from module 1 Read from module CFG 00 2 Write to module Enc Bitrate 6750 Operation finish Vid Resol 120x576 Output Freq 474000 ETWF310 ETWF310 ETWF310 1 Select the option Read from 2 Select the position of CFG 3 A window will appear and it will let module through Up Down buttons memory where you wish to save the you know that the reading made has Press OK to continue current configuration of the module been correct
5. Fle ETWF 310 USER S MANUAL User s manual ETWF 310 NOTE This user s guide is adapted to software version v 0 1 50 of ETWF 310 dated 28 05 2014 For future software updates you can download the users guide from the following website http www ftemaximal com Chapter 1 Installation 1 1 Safety Measures 1 Never place the device next to hot sources 2 Never undergo the device to temperatures that exceed ts level of operation 3 Never expose the device to leaking nor spattering 4 Never place objects that contain liquids over the device 5 Respect the ventilation slots of the device do not cover them with any kind of object 6 The space around the device must be free of objects in a minimum radius of 40cm 7 Avoid locations with possibilities of spilling liquids on the inside of the device and with important changes of temperature 8 Never open the device by yourself due to electric risk In case of problems go always to qualified technicians 9 Never under no circumstances open the device when connected to the electrical net 10 During the handling it is better to disconnect the device from the electrical net 11 Obey the electricity security rules during the assembling Use materials that obey the current law 12 The connecting plug must be accessible in a fast and simple way to have a fast disconnection 13 Never touch the plug with wet hands Also disconnect always the device before handling the
6. connections 14 Never put any heavy object over the device since it could get damaged 15 If the device is going to remain some time without use it is recommendable to disconnect it from the electrical net 16 The repairmen and the maintenance of the device must be done by TV and radio specialised technicians 1 2 Box content Pd Quick installation guide Link F male F male DC Cable ETWF 310 Cable 12 cm PIN to PIN RJ45 RJ45 Ss ETWF 310 version_en_2 0 FTE maximal User s manual ETWF 310 1 3 Description and connections The module ETWF 310 is used for the reception of two base band channels A V Each module allows the modulation of both base band input signals in a multiplex DVB T COFDM A feature of this equipment is its modulator in Vestigial Side Band or VSB This modulation can be used to distribute adjacent channels in one distribution without any interference problem Each module has one Loop connector to cascade several modules at input and a Mix connector to do same in output channels The output channel is selectable between C2 and C69 All parameters are programmed by the means of PRO 201 PRO 300 or the EVO or MINI series of field strength meter and they are monitored in the display of programmer or in the screen of field strength meter ETWF 310 1 Two colored led It indicates the different states of the device 2 OUT This connector supplies the modulated channel according to th
7. have this state by default Always It selects the services automatically every time a new input carrier is tuned This state is only recommended to be used for making test in the module Off The automatic mode is deactivated the services have to be manually selected Advanced settings Excessive capacity It is recommended to remove services 3 Once you have chosen the service select the Add Rem button to remove the service in the multiplex Network It allows making the adjustment of the identification parameters of the multiplex TS ID Transport Stream identification value It is recommended to configure a value different from TS ID for each one of the output multiplex configured Net ID Net identification value Original Net ID Original net identification value Network Name Name associated with the net 8 ETWF 310 version_en_2 0 FTE maximal User s manual ETWF 310 Services Change service name It allows changing the name of the service manually In order to do so please choose the service in the first line and then write the new name in the second line Then you have to press modify in order to save the changes Next it is attached the identification table NID ONID of the main satellites You will be able to find more information in the law ETSI TR 101 162 v1 2 1 Satellite Net ID Original Net ID Hotbird 13 E Eutelsat 13 E Eutelsat 13 E System Astra 19 2 Astra Sa
8. option we have the possibility of choosing if we want to work into the internal disk or in the external storage device USB 2 0 Once the option is selected a dialog box will appear and we will be able to choose among three different options Auto The Meter decides where the data will be stored If there is external memory connected the Meter will store the data in it If not it will use the internal memory USB The Meter always will try to use the external memory connected to the USB port If this memory has not been connected an error message will be shown reminding that there was an error storing the data and it will be not stored Internal Always the internal memory is used to store the data Load programs from USB This option allows importing programs from a USB memory to the field strength meter Before using this option you must connect a USB memory a Save programs to USB This option allows copying the programs stored in the external USB 2 0 storage device Write Alias It allows saving the alias of the module in the program Options Yes No 8 Set Output Services This option allows making the selection of the services that you wish to include in the output multiplex Add Remove services It allows adding the services to the multiplex and also removing the ones previously included The lower bar informs about the available space in the output multiplex As you add more services the space available will decrease
9. the input that will be configured In order to Note From PRO 300 programmer you can only carry out the programming of a single module in order to carry out the programming of several modules at the same time you have to use a mediaMAX EVO or mediaMAX Main menu 1 1 0 configuration 2 System SD Backup ETWF310 T O configuration 1 Input Ana 2 Ont Terr Se item iy 4 Services config ETWF310 Input Ana 1 Enc Bitrate 6750 Ze Vidi Resol TAOSG So 0 4 Aud mode Stereo ETWF310 configure input 1 please select O and if you want to configure input 2 please select 1 Once the input has been selected the rest of the parameters of this menu will configure the selected input signal with the exception of the parameters for Video Resolution and Codification Rate which are the same for both inputs Audio mode It allows selecting the audio mode of the output Options Stereo J Stereo Dual and Mono Audio rate It allows selecting the audio rate in Kbits s Options 32 48 56 64 80 96 112 128 160 192 256 288 320 352 384 416 y 448 depending of the audio mode selected Video frame rate Number of images per second Options 50 60 Aspect Output Image Relation appearance Options Auto 1 1 4 3 16 9 2 21 1 Terrestrial modulation Out Terr These options allow configuring the DVB T DVB H modulator of the device Modulation Output modulation format 4 QAM 16 QAM 64 QAM Inver
10. 12 807 13 195 0 368 10 978 1 310 3 824 14 637 5 080 A 5 551 17 279 18 296 18 850 O 9 331 E 11 2 3 12 441 13 15 64 QAM 2 13 996 5 551 16 466 16 965 16 329 8 143 19 211 19 793 Note Only aplicable for DVB H 20 ETWF 310 version_en_2 0 FTE maximal ESPANA Corrals Nous 77 Pol Industrial Can Roqueta 08202 Sabadell Barcelona Espa a Tel 34 93 729 27 00 Fax 34 93 729 30 73 infofOftemaximal com www ftemaximal com DEUTSCHLAND Zweigniederlassung Deutschland Furstenhof 68 59368 Werne Amtsgericht Dortmund HRB 21674 Ust ID Nr DE243384161 Tel 49 2389 92419 0 Fax 49 2389 92419 25 info ftemaximal de www ftemaximal com FRANCE Fte maximal France SAS 7 avenue du Pont de Tasset 74960 MEYTHET Tel 33 4 50 68 80 17 Fax 33 4 50 68 84 68 fte ftemaximal fr www ftemaximal com PORTUGAL Rua Jos Carlos Ary dos Santos A das Lebres Loures 2660 173 Santo Ant o do Tojal Tel 00 351 21 983 87 00 Fax 00 351 21 983 87 09 ftemaximal ftemaximal pt www ftemaximal com Fle maximal ITALIA Via Edison 29 42040 Calerno di Sant llario d Enza RE Tel 00 39 05 22 90 97 01 Fax 00 39 05 22 90 97 48 infoOfte it www ftemaximal com UNITED ARAB EMIRATES P O Box 262442 BOUTIQUE VILLA 06 2nd Floor BEHIND KNOWLEDGE VILLAGE MEDIA CITY Dubai UAE Tel 00 971 4 4385509 Fax 00 971 4 4385508 info ftemaximal com www ftemaximal com
11. 256 TRSg9IL CHI 2 Delete services Operation finish BW usage BW usage 028 ETWF310 ETWF310 Mux 0 ETWF310 1 Select the option Delete services 2 Select the service you want to 3 A window will appear and it will let through Up Down buttons Press OK delete with the Left Right keys Then you know that the operation made has to continue press OK over Rem in order to been correct remove it or press OK over All in order to delete all the services of the multiplex 14 ETWF 310 version_en_2 0 FTE maximal User s manual ETWF 310 Note It is not recommended to exceed the 85 of the maximum capacity of the multiplex due to the possible variability of the bits rate of the inputs services Output service name This option allows editing the services name and changing it By means the bottoms Left Right the service to edit is selected pressing OK the edition mode is on placing the cursor over the digit the value could be changed by means the bottoms Up Down One time finished the changes are saved pressing OK LCN The LCN function allows assigning automatically a predetermined position to each one of the services of the multiplex This function will allow the users who have a receiver with LCN support to make the ordination of channels automatically Select a channel through Left Right buttons and introduce the position Press the OK button and the cursor will be placed over the number W
12. OB 10 053 10556 12064 13 271 14 745 15 612 16 086 18095 20107 PID 180968 4 22 394 5 6 24 882 04 882 06 346 97 144 27 647 29 273 30 16 EZ 26 126 29 029 31 668 Useful channel capacity 7 MHz FEC codification Guad Interval Modulation 1 4 1 8 1 16 1 32 4 354 4 838 6 123 6 278 5 806 6 451 7 037 6 532 7 257 7 684 7 917 8 064 8 538 8 797 8 467 8 965 9 237 10 246 10 556 13 661 14 075 15 369 15 834 17 594 18 473 15 834 21 112 23 751 oe 27 Useful channel capacity 6 MHz Modulation FEC codification codification 74 Guad Interval 1 8 1 16 1 32 4 147 4 391 4 524 5 529 5 855 6 032 a 3 732 Y 4976 RPR IZ 5 599 SES 6 587 6 786 5 EE 6 221 6 912 7 318 6 532 7 257 7 684 7917 11 197 12 441 13 173 13 572 48 7 465 8 294 8 782 9 048 16 QAM 9 953 11 059 11 709 12 064 3 2 441 7 8 13 063 13 824 14 637 15 08 14515 15 369 15 834 11 197 12 441 13 173 13 572 14 929 16 588 17 564 18 096 64 QAM 38 6 18 662 16 796 18 662 19 76 20 358 38 19 595 Useful channel capacity 6 MHz Modulation Codificaci n FEC 20 735 21 955 22 62 21 772 23 053 23 751 Guad Interval 1 4 1 8 1 16 1 32 QPSK A8 6912 7318 7 540 9 216 9 758 0 053 10 368 1 520 12 197 12 567 2 3 8 294 10 URGAN 244 9 331 10 368 10 978 11 310 HH 10 886 12 096
13. Press OK again to show the log file Delete LOG file It allows deleting all events stored until this moment Factory default This option restores the values by default of the modules Update FW It allows carrying out the firmware update from the programmer Output services This option allows making the selection of the services that you wish to include in the output multiplex Adding Services 3 A window will appear and it will let you know that the configuration made has been correct 3 A new window will appear It will show the information about the registered events in the module Press the following keys in order to scroll up and down the screen up down 1 Select the option Add services through Up Down buttons Press OK to continue 2 Select one of the transponder services you want to add through Left Right keys and select the Add button to include the service in the multiplex 11 ETWF 310 3 A window will appear and it will let you know that the operation made has been correct version_en_2 0 FTE maximal User s manual ETWF 310 Deleting Services 1 Select the option Delete services 2 Select the service you want to 3 A window will appear and it will let through Up Down buttons Press OK delete with the Left Right keys Then you know that the operation made has to continue press OK over Rem in order to been correct remove it or press OK over All i
14. commend you to provide the inputs and outputs which are not used with a 75Q load i Note In order to guarantee the right running of the different equipments of OUT Accessories Programmer Field strength meter Mod PRO 201 Code 2003123 Mod MediaMAX MINI Mod PRO 300 Code 2003127 Wide band amplifier 47 862MHz Mixer Mod AMP 310 P Mod MUX 310 Code 2003520 Code 2003518 ls ETWF 310 version_en_2 0 FTE maximal User s manual ETWF 310 Chapter 2 Technical features Ref ETWF 310 2003566 2 x A V Stereo gt 1x COFDM Imput video level Vpp 1 75 Ohms Imput audio level Vpp 0 6 Audio impedance 75 Ohms Coding rate kbits s 500 6750 Auto 1 1 4 3 16 9 2 21 1 720x480 360x480 352x240 176x128 480x480 544x480 DVB T DVB H Bandwidth MHz DVB T 6 7 8 DVB H 5 6 7 8 C2 C69 F female Regulation margin 15 dB lt 1 dB 60 dBc Programming Interface RJ 45 PRO 201 PRO 300 media Max EVO and media Max MINI 0 C 45 C 1330 300 0 Dimensions 75x265x150 mm L Chapter 3 Declaration of conformity CONFORMITY DECLARATION WE FTE MAXIMAL DECLARE THAT THE PRODUCT ETWF 310 IS INCONFORMITY WITH FOLLOWING DIRECTIVES Low Voltage Directive 2006 95 EC EMC Directive 2004 108 EC If you wish a copy of the conformity declaration please contact to the company 18 ETWF 310 version_en_2 0 FTE maximal User s manual ETWF 310 ATACHMENT Depending on the configured
15. dwidth BW Audio rate Tx Mode FFT Mode Video framerate FEC Video Relation Mode 2 Auto This option allows saving and loading the configuration of the module in the PRO 201 programmer Read from module It stores the current configuration of the module in the memory of the programmer The steps to make a correct reading of the headend are specified below 1 Select the option Read from 2 Select the position of CFG 3 A window will appear and it will let module through Up Down buttons memory where you wish to save the you know that the reading made has Press OK to continue current configuration of the module been correct 10 ETWF 310 version_en_2 0 FTE maximal User s manual ETWF 310 Write to module It loads in the module one of the configurations previously saved in the memory of the programmer The steps to make a correct configuration of the headend are specified below 1 Select the option Write to module through Up Down buttons Press OK to continue 3 Contig 2 Select the position of the CFG memory that you wish to copy in the module Please verity that the data of the selected memory correspond to the channel that you wish to copy In Config option the information concerning the module is given Read log It allows reading the registered events in the module 1 Select the option Read LOG file through Up Down buttons Press OK to continue 2
16. e selected standard in the module and mixes it with all the signals that it 5 receives through the MIX connector e 3 MIX Input of mixing of the module 4 L1 R1 RCA audio inputs channel 1 5 L2 R2 RCA audio inputs channel 2 6 RS 232 Ethernet connector to cascade modules with the RCM 310 telecontrol unit with the RJ45 RJ45 cable provided g PRO 201 Ethernet connector to make the programming with the programmer 8 Video 1 Video 2 RCA video inputs channel 1 amp 2 9 DC connectors It has two connectors for connection between modules States of two colored leds 1 Initialization mode Green main application charged Blinking Green Completing the initial sequence at the moment when the module gets initialized the led will turn into one of the states the operating mode Red Phase of initializing the module 2 Operative Mode Green The system is working properly Orange At least one critical event has been recorded in the module The led will only change into green when the registration of events has been read by the programmer Red Error or alert detected in the running of the device the led will be on only as long as the error alert is present Once the error or the alert disappears the led will change into orange because the error alert is stored in the registration of events 3 Programming mode When the module detects an external programmer the led will blink in the next sequence green oran
17. ents in the module Read log It allows reading the registered events in the module Clear log It allows deleting all events stored until this moment Export log to USB It allows you to export all events registered to the connected USB device NM low Limit dB An event of error will be recorded when t he value of Noise Margin is lower than the set value NM high limit dB Once the event of error is recorded Noise Margin lt Limit Lower NM this will be Noise Margin value that will have to be exceed so the module stops being in error Clear log all devices It allows deleting the events report of all the interconnected modules Factory default This option restores the values by default of the module System information It allows you to visualize the basic information of the module model no of series firmware version etc Settings This option allows saving and loading the configuration of and date of the module Clock Set Date and time Setting of the date and time of module It is appropriate to maintain these parameters set in order to have the registration of errors linked to the current time and date Set date time all devices Loading the current date and time of the module in the rest of interconnected modules Alias Write alias It allows you to assign a name alias to the module you are programming Option only available when the Alias Auto option is configures as none
18. ge red Once you leave the programming mode the led will turn into the corresponding operating mode 2 ETWF 310 version_en_2 0 FTE maximal User s manual ETWF 310 1 4 Programming ETWF 310 has two ethernet connectors In order to make the programming of the module you have to connect the corresponding programmer to PRO 201 connector You can make the programming through the PRO 201 PRO 300 programmers and also through the mediaMAX EVO and mediaMAX MINI field strength meter 1 4 1 Programming modes With mediaMAX EVO mediaMAX MINI field strength Through PRO 201or PRO 300 the programming is made meter you can carry out the programming of all the module by module modules consecutively as long as they are interconnected with each other through the RJ 45 cable supplied with each unit 1 4 2 Programming Below you will find the steps to follow in order to make the programming both from corresponding EVO and MINI field strength meter as well as from PRO 201 and PRO 300 mediaMAX EVO mediaMAX MINI In order to start programming the ETWF 310 encoder you will have to go to Tools option through the key 8 of your field strength meter and to select the Transmodulator Prog option Then it will proceed to recognize the module and to show the main menu In the Transmodulator Prog are shown the different configuration options that this tool offers 3 ETWF 310 version_en_2 0 FTE maximal User
19. ith the keys of the cursor we can move through all the digits and change the values Press OK in order to save the changes ETWF310 OATES oc AZ Note If in the existing installation there are already services that have LCN system you will have to configure the position of the module services in order to avoid conflicts with other net services Network Option This option allows adjusting the identification parameters of Network options multiplex Network name Associated name to the network TSID Identification value of Transport Stream Give a different value of TSID 3 Sa for each output multiplex configured is recommended 4 EH NID Identification value of the network l ONID Original identification value of the network ETWF310 2 System In System option the information concerning the module is given Ee SW version info It allows you to visualize the basic information of the module 1 SW version info model firmware version etc 2 Dare Time Date Time Setting of the date and time of the module It is appropriate to 3 Read LOG file maintain these parameters set in order to have the registration of errors linked 4 Delete LOG file to the current time and date ETWF310 Read LOG file It allows reading the registered events in the module System Read LOG file SW version Into N 00000 Status 00 2 Date Time 28 07 14 13 49 26 3 Read LOG file System Ok 4 Delete LOG file ETWF310
20. l 8MHz 7MHz 6MHz and 5MHz The 5MHz option is only supported by DVB H standard Tx Mode FFT Mode 8K 4K and 2k The 4k option is only supported by DVB H standard FEC Indicates the relationship between the redundant bits and the transmitted information bits 1 2 2 3 3 4 5 6 and 7 8 For example in a FEC 2 3 relation we will find 2 information bits and 1 redundant bit Mode Selection of the modulation standard DVB T and DVB H codification and modulation In the Attachment you will find all the information related to the resulting useful bit Note The output useful bits rate will depend on the following parameters Bandwidth guard interval FEC rate in each configuration Output configuration TV output In these options you can configure the output parameters of the terrestrial signal RF Channel MHz Output frequency of terrestrial modulation In order to introduce the frequency press the OK button and the cursor will be placed over the frequency With the keys of the cursor we can move through all the digits and change the values Press OK in order to save the value Options 47 862 MHz RF Level Regulation of the output level of the modulated signal Options O 15dB Summary table Analogue input Terrestrial output TV output Coding rate Modulation RF Channel Video Resolution Invert Spectrum Inversion RF Level Input selecting Guard Interval Gl Audio mode Ban
21. l the digits and change the values Press OK in order to save the value Options 47 862 MHz ETWF310 RF Level Regulation of the output level of the modulated signal Options O 15dB 1 RF Channel REN gees Summary table Analogue input Terrestrial output TV output Coding rate Modulation RF Channel Video Resolution Invert Spectrum Inversion RF Level Input selecting Guard Interval Gl Audio mode Bandwidth BW Audio rate Tx Mode FFT Mode Video framerate FEC Video Relation Mode Services configuration This option allows configuring the features of the output services Services config S Output services This option allows making the selection of the services that 5 Output serv Name you wish to include in the output multiplex 3 LCN 4 Network options Adding Services ETWF310 Output services Output services Output services PID 00256 TR391 CH1 2 Delete services 1 Add Operation finish BW usage BW usage 028 ETWF310 ETWF310 Mux O0 ETWF310 1 Select the option Add services 2 Select one of the multiplex services 3 A window will appear and it will let through Up Down buttons Press OK you want to add through Left Right you know that the operation made has to continue keys and select the Add button to been correct include the service in the multiplex Deleting Services Output services Output services Output services JL Aci sSivices PID 00
22. lues Press OK in order to save the changes Note If in the existing installation there are already services that have LCN system you will have to configure the position of the module services in order to avoid conflicts with other net services 12 ETWF 310 version_en_2 0 FTE maximal User s manual ETWF 310 PRO 300 A When you connect the PRO 300 programmer it will proceed to recognize the module and to show the main menu In the main menu are shown the different options for configuring the module We have to use the Up and Down buttons of the keyboard in order to move to the different options and to get into the submenus we have to press OK button MINI series field strength meter 1 I O configuration Inside the manual menu there are specified the different options for setting up the input output and modulation parameters In order to move around the different options we have to use the Up and Down buttons of the keyboard Click on OK to edit the selected parameter and Right Left for changing it Once it is configured press Cancel Analog input Input Ana With this option you will be able to configure the input parameters of each one of the two A V inputs Coding rate Coding rate of the output video Options Auto or 0 6750 Kbps Video Resolution Output Video Resolution Options 360x576 352x288 176x144 480x576 544x576 720x576 Input It allows selecting
23. manual mode Auto Alias It allows configuring the name alias of the modules automatically Options Channel Frequency Service None Upgrade Send Firmware from USB It allows carrying out the firmware update from the USB device Send firmware to all It allows carrying out the update of all the modules that are interconnected at the same time Configure all devices Input values to all devices It allows copying the current input configuration in all the interconnected modules Modulator values to all devices It allows copying the configuration of the current modulator in all the interconnected modules Output values to all devices It allows copying the current output configuration in all the interconnected modules Factory default to all devices It allows making values by default to all the interconnected modules 6 ETWF 310 version_en_2 0 FTE maximal User s manual ETWF 310 7 Program management New program This option allows creating a program with the current configuration of a module or group of modules Load program It allows loading a previously created program on a module or group of modules Delete program It allows deleting a program Device to process Current The creation or loading of a program will be applied only in the module that is currently connected All The creation or loading of a program will be applied to the whole group of connected modules Working disk With this
24. n order to delete all the services of the multiplex Note It is not recommended to exceed the 85 of the maximum capacity of the multiplex due to the possible variability of the bits rate of the inputs services Change service name It allows changing the name of the service manually Date Time Setting of the date and time of module It is appropriate to maintain these parameters set in order to have the registration of errors linked to the current time and date SW version info It allows you to visualize the basic information of the module model firmware version etc Global Update It allows carrying out the update of all the modules that are interconnected at the same time TSID Transport Stream identification value Note It is recommended to configure a value different from TS ID for each one of the output multiplex configured NID Net identification value ONID Original net identification value Network Name Name associated with the net LCN The LCN function allows assigning automatically a predetermined position to each one of the services of the multiplex This function will allow the users who have a receiver with LCN support to make the ordination of channels automatically Select a channel through Left Right buttons and introduce the position Press the OK button and the cursor will be placed over the number With the keys of the cursor we can move through all the digits and change the va
25. ng the input that will be contigured In order to configure input 1 please select O and if you want to contigure input 2 please select 1 Once the input has been selected the rest of the parameters of this menu will configure the selected input signal with the exception of the parameters for Video Resolution and Codification Rate which are the same for both inputs Audio mode It allows selecting the audio mode of the output Options Stereo J Stereo Dual and Mono Audio rate It allows selecting the audio rate in Kbits s Options 32 48 56 64 80 96 112 128 160 192 256 288 320 352 384 416 y 448 depending the audio mode selected Video frame rate Number of images per second Options 50 60 Aspect Output Image Relation appearance Options Auto 1 1 4 3 16 9 2 21 71 i Note From PRO 201 programmer you can only carry out the programming of a single module in order to carry NO 9 ETWF 310 version_en_2 0 FTE maximal User s manual ETWF 310 Terrestrial modulation Out Terr These options allow configuring the DVB T DVB H modulator of the device Modulation Output modulation format 4 4 QAM 16 16 QAM 64 64 QAM Invert Spectrum inversion Activate or deactivate the spectrum reverse in the modulation Gl Guard interval Allows selecting the guard interval of the modulation 1 4 1 8 1 16 and 1 32 BW Bandwidth Selection of the Bandwidth of the modulated signa
26. parameters we are going to obtain one particular channel capacity output useful bit rate In order to make an estimation of this output bits rate we have to take into account the following parameters Symbol duration Ts For signals of 8 MHz 8K 6817 carrier 4K 8409 carrier 2K 1705 carrier Symbol duration 448 us 224 us Symbol duration Interval 1 4 1 4 1 8 e 1 8 1 16 1 32 1 4 1 8 1 16 Duration 294us 19us 56us 28us 19us 56us 28us 14us 56us 28us 14us For signals of 7 MHz 1 32 Mode 8K 6817 carrier 4K 8409 carrier 2K 1705 carrier Symbol duration 1024 us 256 us po Gus Guard Interval For signals of 6 MHz 8K 6817 carrier 4K 8409 carrier 2K 1705 carrier Symbol duration Guard Interval 1716 1 32 1 16 1 732 1 4 1 16 298 7us 149 3us 149 3us 18 6us_ 74 6us 9 3us For signals of 5 MHz 8K 6817 carrier 4K 3409 carrier 2K 1705 carrier Symbol duration 1433 6 us Guard Interval 1 4 1 8 1 16 1 32 1 32 358 4us 179 2us 179 2us 22 4us_ 89 6us 11 2us Modulation Modulation QPSK 16 QAM 64 QAM Number of bits per symbol 2 4 6 FFT Mode FFT Mode 8K 4K 2K Data carriers 6048 3024 1512 6817 3409 1705 Bits rate calculation total fs b L Dive Where Fs Symbols frequency symbols sec fs 1 Ts Ts Symbol duration Symbol Time Guard Interval time b Number of bits per symbol depending on the modulation L Number of da
27. s manual ETWF 310 1 Select Device The field strength meter allows carrying out the programming of one or several modules from an only modules Without interconnection of modules Interconnection of several modules you can select which An only module connected module you wish to program 2 Device Status In the option Device Status are specified the main parameters of the module at this moment Front End It indicates whether the module is hooked or without signal Output bit rate Transfer of data in the module output Temperature It indicates the current temperature of the module in degrees 3 Set Front End With this option you will be able to contigure the input parameters of each one of the two A V inputs Input selecting It allows selecting the input that will be configured In order to configure input 1 please select O and if you want to configure input 2 please select 1 Once the input has been selected the rest of the parameters of this menu will configure the selected input signal with the exception of the parameters for Video Resolution and Codification Rate which are the same for both inputs Audio mode It allows selecting the audio mode of the output Options Stereo J Stereo Dual and Mono Audio rate It allows selecting the audio rate in Kbits s Options 64 96 112 128 160 192 224 256 288 320 352 384 416 and 448 Coding rate Coding rate of the output video
28. t Spectrum inversion Activate or deactivate the spectrum reverse in the modulation Gl Guard interval Allows selecting the guard interval of the modulation 1 4 1 8 1 16 and 1 32 BW Bandwidth Selection of the Bandwidth of the modulated signal 8MHz 7MHz 6MHz and SMHz The SMHz option is only supported by DVB H standard Ou cere 1 Modulation 2 Invert 3 61 4 Bandwith ETWF310 Tx Mode FFT Mode 8K 4K and 2k The 4k option is only supported by DVB H standard FEC Indicates the relationship between the redundant bits and the transmitted information bits 1 2 2 3 3 4 5 6 and 7 8 For example in a FEC 2 3 relation we will find 2 information bits and 1 redundant bit Mode Selection of the modulation standard DVB T and DVB H A rate in each configuration 13 ETWF 310 Note The output useful bits rate will depend on the following parameters Bandwidth guard interval FEC codification and modulation In the Attachment you will find all the information related to the resulting useful bit version_en_2 0 FTE maximal User s manual ETWF 310 Output configuration Out TV In these options you can configure the output parameters of the terrestrial Out TV signal RF Channel MHz Output frequency of terrestrial modulation In order to introduce the frequency press the OK button and the cursor will be placed over the frequency With the keys of the cursor we can move through al
29. ta carriers depending of FFT mode Bits rate calculation useful Tb set TB ota i Codif rec Codif e cd Salomon FEC Cod FEC Codification 1 2 2 3 3 4 5 6 7 8 Reed Salomon Cod Codification made by the means of Reed Salom n algorithym 188 204 Case study example For example in the case of a DVB T transmission in Spain the configured parameters would be the following 8k mode 2 3 FEC 1 4 guard intervals 64QAM constellation for an 8 MHz channel and using the previous formula you will get the following channel useful capacity Tb 19 905 Mbps util Note As you select a configuration with a higher output channel capacity the protection grade against mistakes gets proportionally decreased Next it is shown the channel capacity for systems without hierarchy in all the cases of constellation guard interval and codification relation for transmissions of 8MHz 7MHz 6MHz y BMHz DVB H The useful capacity channel is identical for modes 2k 4k DVB H and 8k 19 ETWF 310 version_en_2 0 FTE maximal User s manual ETWF 310 Useful channel capacity 8 MHz Modulation FEC codification codification Guad Interval 1 4 1 8 1 16 1 32 7 465 8 294 8 782 9 048 8 294 9 216 9 758 0 053 4 976 5 529 5 855 6 032 OPSK i A O f 6 635 7 373 7 806 8 043 _ Le 8 709 9 676 10 246 10 556 A 9 953 11 059 11 709 12 064 16 QAM 14929 16 588 17 564 18 096 20 107 21 112 8 096 Pp
30. tellite Network 19 2 E Astra 28 2 E Astra Satellite Network 28 2 E PRO 201 out the programming of several modules at the same time you have to use a mediaMAX EVO or mediaMAX MINI series field strength meter When you connect the PRO 201 programmer it will proceed to recognize the module and to show the main menu In the main menu are shown the different options for configuring the module We have to use the Up and Down buttons of the keyboard in order to move to the different options and to get into the submenus we have to press OK button 1 Manual Inside the manual menu there are specified the different options for setting up the input output and modulation parameters 1 1 This field shows the type of parameter that is selected at the moment Options Input Ana Out Terr Out TV 2 This field shows the parameter that is selected In order to move around the different options we have to use the Up and Down buttons of the keyboard Click on OK to edit the selected parameter and Right Left for changing it Once it is configured press OK Analog input Input Ana With this option you will be able to configure the input parameters of each one of the two A V inputs Coding rate Coding rate of the output video Options Auto or 0 6750 Kbps Video Resolution Output Video Resolution Options 360x576 352x288 176x144 480x576 544x576 720x576 Input It allows selecti
31. val FEC rate in each configuration 5 Set Output channel In this option you can configure the different parameters of the cable signal Channel standard It allows you to select the channelling of the cable signal standards Options BG BG PAL BG IT LL M NTSC PAL M PAL N PAL DK PAL BB_AU DK PAL L PAL Channel Output channel of the cable modulation When you select the output channel the field Frequency MHz will be modified automatically adapting itself to the selected channel Options C2 C69 Frequency MHz Output frequency of cable modulation When you modify this field the field Channel will be also modified indicating the channel equivalent to the selected frequency in the case that this frequency corresponds to the frequency of a channel Options 47 862 MHz Level Regulation of the output level of the modulated signal Options O 15dB Calibration Allows the realization of two tests in order to verity the correct running of the device Deactivate output It allows activating or deactivating the output of module Switch output to CW It allows activating or deactivating the DVB T DVB H modulation allowing visualizing the carrier without modulation in the selected frequency 5 ETWF 310 version_en_2 0 FTE maximal User s manual ETWF 310 6 System This option provides information of the module System logfile In this field are indicated the registered ev
Download Pdf Manuals
Related Search