FILTER S MAX ERIES - Emaux Water Technology
Contents
1. PARTS FOR FILTER MAX FILTER Product Description MPV07 6 Way 1 5 Clamp Type Multiport Valve for MFV17 MFV 20 MFV24 MFV27A MFV31A Filter Max MPV08 6 Way 2 0 Clamp Type Multiport Valve for MFV27 MFV31 MFV35 Filter Max 89280102 1 5 Union Set 3 Pieces With O Ring for MPV07 Valve 89280103 2 0 Union Set 3 Pieces With O Ring for MPV08 Valve 06021013 Plastic Pressure Gauge With O Ring 40psi x oO lt z O y o a z Cc 3 ao oO g 2 3 88281505 88280306 01111048 Connector for Pressure Gauge Stopper 89012512 Clamp Kit 01271021 Clamp Lock left 01271022 Clamp Lock right 03021035 M6 Nut 01111101 Star Shaped Nut 03011166 M6x110mm Screws 03018124 02010007 01331024 MFV 17 Filter Tank 01331025 JMFV 20 Filter Tank 01331026 MFV 24 Filter Tank 01331027 JMFV27AMFV27 Filter Tank 01331028 JMFV31AMFV31 Filter Tank 01331029 MFV35 Filter Tank 89012507 Lateral Assembly with Center Pipe for MFV17 89012508 Lateral Assembly with Center Pipe for MFV20 89012509 Lateral Assembly with Center Pipe for MFV24 89012510 Lateral Assembly with Center Pipe for MFV27A 89012513 Lateral Assembly with Center Pipe for MFV27 89012511 Lateral Assembly with Center Pipe for MFV31A 89012514 Lateral Assembly with Center Pipe for MFV31 89012515 Lateral Assembly with Center Pipe for MFV35 01172007 Laterals 115mm for MFV17 01172008 Laterals 126mm for MFV20 MFV 24 MFV27A MFV31A 01172010 Laterals 185mm for MFV22. 20 to 25psi or 50 increase from the clean reading proceed to the 2 Place Add water 1073 Sa oe are Se Ms ee To perform the Backwash operation position the handle on the control valve to Backwash the water flow is automatically reversed through the filter so the water is directed from the bottom of the tank up through the sand flushing the trapped dirt and debris out of the waste line The duration of the backwash EMAUX Emaux Swimming Pool Equipment Co Ltd Long Zhu Industrial Park Nan Lang Industrial Area Nan Lang Town Zhong Shan City ce Guang Dong China M4 AN Water Technology tei 86 76085527988 Fax 86 760 85527188 Email emaux emaux com hk add sand 4 4 1 4 sites 3 Pour the recommended amount of sand into the tank making sure that the centre pipe remains centred and vertical 4 Level the surface of the sand upon completion 5 Remove the Sand Fill Cover 6 Carefully remove all sand particles from the valve mounting surface 7 Place the O ring into the groove on the tank 8 Lower the Multiport Control Valve carefully into position so that its underside engages with the centre pipe Rotate the valve until the inlet is approximately in line with the pump 9 Place the clamp set around the tank and the valve Secure using the screw provided 10 Firmly tap with a rubber mallet outside of the clamps as you tighten the screw 11 Tighten the screw until the Multipo
3. pump for at least 2 minutes The initial backwashing of the filter is recommended to remove any impurities or fine sand particles in the sand media 5 Turn the pump off and set the control valve to RINSE position Start pump and operate until water in sight glass is clear about to 1 minute Turn pump off set valve to FILTER position and restart pump Your filter is now operating in the normal filter mode filtering particles and dirt from the pool water 6 Take note of the initial pressure gauge reading for future reference Variation may occur from pool to pool 7 Adjust pool suction and return valves to achieve desired flow Check system and filter for water leaks and tighten connections bolts nuts as required NOTE During the initial clean up of the pool water it may be necessary to backwash frequently due to the unusually heavy initial dirt load in the water IMPORTANT To prevent unnecessary strain on piping system and control valve always turn off the pump before changing the operation of the control valve To prevent damage to the pump and filter and for proper operation of the system clean pump strainer basket and skimmer basket s regularly MULTIPORT CONTROL VALVE FUNCTIONS FILTER gives downward flow through the filter bed This position can also be used for vacuuming BACKWASH gives upward flow through the filter bed that removes the dirt from the sand and carries it to the waste WASTE is for pumping wat
4. 7 MFV31 MFV35 01172007 Laterals 115mm for MFV27 MFV31 MFV35 89010107 Water Drain Set 01111059 Filter Base for MFV17 MFV20 01111062 Filter Base for MFV24 MFV27A MFV27 01331003 Filter Base for MFV31A MFV31 MFV35 89012516 Laterals bracket for MFV27 MFV31 MFV35 als 7 10 11 15 16 17 15840 Tumover Capacity In Gallons 10Hour 49800 All Sand Required kg Nom 75 70 lt Wn Water Technology FILTER MAX SERIES MODEL MFV17 88012526 MFV20 88012527 MFV24 88012528 MFV27A 88012529 MFV27 88012530 MEV31A 88012531 MFV31 88012532 MFV35 88012533 Your Emaux Filter Max Filter is a high performance corrosion proof filter that has superior flow characteristics that is with the ease of operation Everything is made simple from installation operation to the maintenance of the filter Your Filter Max filter will be your pool filtration partner that provides clear water with the least maintenance hassle and care BEFORE INSTALLATION BE warning Sure TO READ ALL INSTRUCTIONS AND WARNINGS CAREFULLY KEEP THIS USER MANUAL FOR FUTURE REFERENCE HOW IT WORKS The Filter uses special sand to remove dirt particles from pool water Filter sand is loaded into the filter tank to act as the filtration media The pool water which contains dirt particles is pumped th
5. STRY GUIDELINES ACTION REQUIRED TO CORRECT POOL CHEMISTRY SUGGESTED POOL CHEMISTRY LEVELS TO RAISE TO LOWER TOTALALKALIN ITY CHLORINE UNSTABILIZED CHLORINE STABILIZED CHLOR NE STAB LIZER Cyanuric Acid 100 to 130 ppm Add Sodium Bicarbonate Add Muriatic Acid 0 3to1 0 ppm Add Chlorine Chemical No action chlorine will naturally dissipate 1 0to 3 0 ppm Add Chlorine Chemical No action chlorine will naturally dissipate 40 to 70 ppm o Dilution partially drain amp refill pool with water AOA Stabilizer that has not been treated with Cyanuric Acid 3 4
6. er from the pool It allows the flow from the pump to bypass the filter and go directly to the waste You can also use this position to vacuum heavy concentration of debris RECIRCULATE bypasses the filter to circulate water through the pool system RINSE gives a downward flow that settles the filter bed after backwashing and carries any remaining loose dirt to the waste CLOSED prevents only backflow of water from pool during pump maintenance To WINTERISE set the control valve handle in the middle between RINSE and FILTER This will allow air to leave or enter the tank to help priming and draining Only to be used when the pump is off VACUUMING THE POOL Light Soil set the control valve to FILTER position Heavy Soil set the control valve to WASTE position WINTERRISING Backwash the filter for at least thirty minutes before closing down the pool for winterising This will clean the filter bed thoroughly 1 Drain the filter tank by removing the drain cap at the base of the filter tank Leave the cap off during the winter 2 Set the control valve handle between the RINSE and FILTER This will lift the handle and help with the draining process by allowing air to enter into the tank 3 Unscrew the pressure gauge from the control valve and store the gauge indoor 4 Drain and winterise pump according to pump instructions 5 Repairs should be made during the off season when the best service is available do not leave them un
7. ols needed is a screwdriver and pipe sealant for plastic The filter should be installed as close to the pool as possible but keep a distance of at least 5 feet 1 5m Locate the Filter on hard level surface preferably ina dry shaded and well ventilated area Prior to installation give consideration to the following Position of suction return and waste connections Access for backwashing operation and servicing protection from sun rain splashing etc Drainage of filter room Ventilation and protection of the motor 1 Place the empty tank in position 2 Fill the tank with water to the level that covers the laterals crepinas about 1 3 of the tank is recommended This will avoid damages to the laterals crepinas by the force of the sand when pouring into the filter Model MFV17 the Multiport Control Valve had been pre assembled Remove the Multiport Control Valve from the tank by unfastening the screw from the Clamp Place the Sand Fill Cover over the tank opening to prevent the sand from getting into the standpipe Model MFV20 MFV24 MFV27A MFV27 MFV31A MFV31 MFV35 the Sand Fill Cover had been pre assembled MFV17 MFV20 MFV24 i MFV27AMFV31A MFV27 MFV31 MFV35 1 Sand fill cover Tumover Capacity 1 Gallns 12 Hour 70 500 _ 425 50 note of the clean reading when the filter was installed Add water to cover laterals and add sand When the pressure reaches approximately
8. rough your piping system to the filter via the filter control valve As pool water passes through the filter dirt particles will be caught by the sand bed and filtered out The cleaned pool water is returned from the bottom of the Filter Tank through the control valve and back to the pool through your piping system The entire sequence is continuous and automatic It is this sequence that provides the filtration process and circulation of water in your pool With the filtration process dirt will accumulate and becomes saturated in the filter tank Pressure in the tank will increase and the resistance of water flow will occur This means it is time to clean backwash your filter Another indication to know when to clean backwash the filter is by checking the pressure gauge reading Backwash operation should be performed when the pressure increases by 10psi above the pressure when it was clean Typically a clean filter will run at 10 to 15psi depending so take operation will depends on how dirty your filter is Check the sight glass to see when the water becomes clear It is recommended that the backwash should be atleast 2 minutes long Once the backwash operation had been completed the filter should go through the process of Rinse and then back to Filter To do perform the different operations position the handle on the control valve as indicated INSTALLATION Installation had been made simple the only to
9. rt Control Valve is in situ and properly assembled to create a water tight seal Do not over tighten FIGURE3 Clamp Installation tap with a rubber mallet and tighten the screws 12 Install the pressure gauge into the threaded opening on the Multiport Control Valve 13 Install the union sets and the backwash union set 14 Connect pump to the control valve opening marked PUMP 15 Make return to pool pipe connection to control valve opening marked RETURN 16 Connect the waste water pipe to the control valve opening marked WASTE TYPICAL INSTALLATION Pressure Gauge FO Inlet From pump putt et To pool Sa nd OW Drai 17 To prevent water leakage be sure all pipe connections are tight 18 Prior to starting the filtration process by turning on the pump we highly recommend that you read through the pump instruction manual to ensure proper installation and to avoid the risk of electric shock 2 4 START UP PROCEDURE 1 Be sure the correct amount of filter sand media is in the tank and all connections have been made and are secure 2 Turn the Control Valve handle to the Backwash position Press the handle downward before turning 3 Start the pump according to pump instruction manual be sure all suction and return lines are open 4 Once water flow is steady out the waste line run the
10. til the next season TROUBLE SHOOTING SAND BACK TO POOL Sand too small Flow too high Sand bed calcified Broken Laterals Loose centre pipe Too much sand Control Valve not engaged Air accumulation in filter SAND OUT OF BACKWASH HOSE Flow too high Too much sand in tank INADEQUATE FILTERING Dirty make up water improper sand Sand is too low Algae in filter Excessive dirt in pool Calcified sand bed Heavy swimmer load Flow rate too high or too low Backwashing cycle too short Backwash line too small SHORT FILTER CYCLE Dirty filter Improper sand Sand is low Algae in filter Excessive dirt in pool Calcified sand bed heavy swimmer load Flow rate too high or too low Backwashing cycle too short Channels low Backwash adapter in wrong location Channels in sand FILTER LEAKS Tank cracked Drain plug not tight Valve Tank O ring damaged CONTROL VALVE LEAKS Handle not properly engaged Valve Tank O ring damaged Valve cover O ring damaged Pressure gauge O ring damaged ABNORMAL LOSS OF POOL WATER Leak inside Control Valve Leakage from pool or piping HIGH PRESSURE FILTER Dirty filter Calcified sand bed Return lines too small LOW PRESSURE IN FILTER Control Valve incorrectly set Pump running too slow plugged or clogged Air leakage into pump suction NOTE If the recommendation in this manual do not solve your particular problem s please contact your local dealer for service POOL CHEMI
Download Pdf Manuals
Related Search