model 9791 “hertz donut” operator`s manual
Contents
1. The Harvestman implies and accepts no responsibility for un desirable harm to person or apparatus caused through operation of this device The Harvestman reserves the right to change specifications at any time Get in contact The Harvestman Digital Audio Electronics Sebastian Jaeger sebastian theharvestman org http www theharvestman org 1 734 260 5801 2008 The Harvestman Digital Audio Electronics All rights reserved Protected under United States and international copyright law2. wave output as well as a selectable waveform output switchable between Sine Triangle and Saw tooth The Modulation Oscillator behaves much like the Primary but it is missing a facility for modulating the waveform discontinuity The external FM inputs must be manually activated before use Briefly hold the desired Oscillator s waveform button to enable the external FM input The LEDs should all switch off exponential FM is now active Press the button again to switch to linear thru zero FM all LEDs lit This mode contains objectively superior sidebands but also includes some jitter at low modulation indices that may be of fensive to some users Waveform Discontinuity This function allows modification of the waveforms on the Primary side Timbral evolutions are easily achieved here Sine The center of the waveform twists around and expands outwards It then tries to go back where it came from Triangle The slopes grow branches and foliage with several large discontinuities over the sweep of the control Saw The center of the waveform twists around and expands outwards The dedicated square wave output undergoes classic pulse width modulation effects when this control is touched Modulation bus The waveform output of the Modulation Oscillator can be used to internally modulate parameters of the Primary Oscilla tor without patchcords getting in the way of your hands The index is manual or voltage controll
3. THE HARVESTMAN nee MODEL 9791 HERTZ DONUT OPERATOR S MANUAL Dual Digital Oscillator with Internal Modulation Bus NEEN 2 DONUT wort THE HARVESTMAN 9791 HERTZ DONUT USER S MANUAL Table of Contents Front Panel Key Introduction Configuration Power cable orientation Features Primary and Modulation oscillators Waveform Discontinuity Modulation bus Modulator tracking Calibration Warranty A Primary Osc Coarse Tune Controls the Primary oscillator frequency Acts as offset when control voltage is ap plied to D B Primary Osc fine tune C Primary FM Attenuator see E D Tuned Primary CV input Accepts 1v octave control signal 1 E Primary Linear FM input Linear thru zero frequency modulation of the Primary oscillator t F Primary Sync input Restarts Primary waveform on receipt of a rising edge G Waveform Discontinuity CV input H Waveform Discontinuity CV Attenuator see J J Waveform Discontinuity manual control Distorts the Primary Oscillator s waveform Also acts as offset for input G K Tracking behavior button Determines how quickly the Modulation oscillator follows the Primary Selected behav ior is shown on nearby LEDs L Modulation Osc Coarse Tune Controls the Modulation oscillator frequency Acts as offset when control voltage is applied to Q Modulator Osc fine tune N Modulator Frequency Range Selects a high audio or
4. ed and acts on all selected destina tions Any combination of three destinations are possible Frequency modulation Internal thru zero linear FM with a high index Waveform discontinuity modulation Acts over a range of the discontinuity sweep Use with the manual discontinuity control for more extreme effects Amplitude modulation modulates the master ampli tude of the Primary s selectable waveform output The index control acts as a volume control for the upper and lower sidebands Modulator tracking When activated the frequency of the Modulation oscillator will attempt to follow that of the Primary with varying degrees of success The modulation frequency range controls are disabled or assigned alternate functions in these modes O mode The Primary Frequency control and CV input have a slight delay in catching up to new values which are passed on to the Modulation Oscillator frequency control This is not very notice able unless large jumps in CV input are made or if you assign the modulation oscillator to modulate the primary s frequency In this FM feedback loop you will experience strange chaotic behaviors that are nicely experienced by listening to the Primary with some waveform discontinuity Or use the modulator output to modulate some other module In this mode the Modulation oscillator manual fre quency controls and CV input cause an offset from the frequency of the primary o
5. ght up Now the modulation oscillator output is a strict copy of the Pri mary s but with its waveform shifted 90 degrees forward Calibration Connect the square wave output of either oscillator to a fre quency counter or tuner Turn the manual frequency control all the way down and adjust the fine tuner until you have 20 Hz Connect a quantized voltage source 1v oct or MIDI CV interface to that side s tuned CV input Increase the CV input by several octaves Double the 20Hz figure for every octave you move for example 4 octaves up would result in a frequency of 320Hz Turn the trimmer on the side of the module corresponding to the oscillator you re lis tening to Adjust until the tuner displays the desired frequency Calibrate the other half of the module if necessary Don t play with the trimmers or disassemble the module unless you absolutely have to The guardian will eat you for breakfast if you disturb his beauty sleep Warranty Repairs resulting from a defect of the device or its construction process shall be covered for two years after manufacture with cus tomer paying transit costs Device dysfunction resulting from incorrect power supply volt ages backwards power cable connection attempted reverse engi neering or decoding of intellectual property abusive performance fluid encroachment or out of specification voltage input is not cov ered by this warranty and normal service rates will apply
6. low LFO range When Tracking is enabled it selects alternate time constants or operation modes P Modulator FM Attenuator see Q Q Tuned Modulator CV input Accepts 1v octave control signal t R Primary Linear FM input Linear thru zero frequency modulation of the Modulator oscillator 5 Modulator Sync input Restarts Modulator waveform on receipt of a rising edge T Modulation Index CV input V Modulation Index CV Attenuator see W W Modulation Index Manual Control Applies the Modulator Osc waveform to the parameters selected by button X Y Primary Waveform Selector Selects Primary Osc waveform shown on LED to be output from jack Z When held down for a brief period of time it will enable FM input E While the input is active pressing this button will switch the FM mode between linear and exponential Z Primary Waveform output 5V waveform output for Primary Osc AA Primary Square Wave output Dedicated square wave PWM output for Primary Osc BB Gate Output Normally produces the XOR of the square outputs 0 5V also generates gates when Tracking is enabled CC Modulator Square Wave output Dedicated square wave PWM output for Modulator Osc DD Modulator Waveform output 5V waveform output for Modulator Osc EE Modulator Waveform Selector Selects Modulator Osc waveform shown on LED to be output from jack DD When held down for a brief period of time it will enable FM input R While the input is active
7. pressing this button will switch the FM mode between linear and exponential Inputs expect 0 5 control voltage Values out of this range may cause mild undefined behavior Use those manual knobs and attenuators T Inputs D Q expect a 0 10V control voltage Values out of this range may cause mild undefined behavior Use those manual knobs and attenuators Inputs E R expect a 5V audio signal in linear mode 0 5V in expo mode Introduction The Hertz Donut is a dual digital oscillator with an internal modulation bus and voltage controlled waveshaping Each half of the module can independently track 1v octave receive linear thru zero FM hard sync and output four different waveforms over two outputs The user interface features momentary tactile switches for switching modes with LED indicators showing most onboard states Configuration The Hertz Donut occupies 17HP of rack space and requires Eurorack style power distribution board When connecting the power cable to your enclosure orient the red band of the module s power cable to point towards the 12V power rail If you experience difficulty with the module s odd front panel measurement you may solve this by adding another odd measured Harvestman module to the system Features Oscillators The Primary Oscillator features inputs and controls for tuned CV 1 sync external FM and waveform discontinuity It features a dedicated square
8. sc If you set the knobs at 12 noon you will be be near the true primary frequency Turn the knob in either direction to achieve a positive or negative offset Now change the primary frequency and the modulator will follow with this offset useful for double stops octaves etc The gate output of the module goes HIGH when the module has locked onto its destination pitch Worse mode Like the Bad mode but with a longer convergence time and larger skips Generates arpeggios from beyond when too much FM feedback is applied Stupid mode The primary oscillator is unaware of how to find its new frequency so it searches for one and often fails The Modulation os cillator frequency control lets you choose the time between search updates Listen to it for long enough and you might start hearing things Each of the previous three tracking modes can be ex tended by pushing the modulation frequency button This enables shorter time constants or longer searches depending on the mode Good mode The modulation oscillator tracks the primary without trouble The pitch offset is easily tuned by turning the Modulation Frequency controls while watching the gate output LED unison and octaves will show a slowing of the pulsing light The gate output fea tures the usual XOR ringmod of the square outputs Phase offset mode Push the modulation frequency range button while Good mode is active Both LEDs should li
Download Pdf Manuals
Related Search