English - Scene7
Contents
1. 61063 01 Parts in the Box Latch and Strike Exterior Assembly Interior Assembly gP ii Kevo Installation and User Guide ENGLISH Required Tools You can view the ee E Kevo installation video Ruler Phillips Head Screwdriver online by scanning E E Q m Additional Accessories the code to the right mw depending on application or by visiting ol Kevo Fob CO www kwikset com i Cm kevo support Hammer Wood block J mm Ea Prepare door and check dimensions If drilling a new door use the supplied template and the complete door drilling instructions available at www kwikset com doorprep Measure to confirm that the hole in the door Measure to confirm that the backset is either Measure to confirm that the hole in the door D Measure to confirm that the door is either is either 2 1 8 54 mm or 1 1 2 38 mm 2 3 8 or 2 3 4 60 or 70 mm edge is 1 25 mm 1 3 8 or 1 3 4 35 mm or 44 mm thick 1 3 8 or 1 3 4 35 mm or 44 mm Note Additional door preparation may be required for doors with 1 1 2 38 mm holes Consult the deadbolt drilling instructions at www kwikset com doorprep p Install latch and strike Is the door edge chiseled Hold the latch in front of the door hole with the latch face flush D Which latch are you installing against the door edge 0 not chiseled Use latch A2 Extend the latch bolt as shown A2 A Are the latch holes centered in2. wena 1800 623 118 0800 736 776 www kwikset com kevo support 2014 Kwikset Corporation
3. ie Read all instructions in their entirety Familiarize yourself with all warning and caution statements Remind all family members of safety precautions Always have access to your lock s standard key If using the Triple Touch Lock feature make sure to have your smartphone fob or standard key with you to prevent locking yourself out Familiarize yourself with all light ring error notifications Replace low batteries immediately Preventing Inadvertent Unlocking of Your Door A WARNING Failure to follow these safeguards could result in your lock opening inadvertently Avoid keeping and storing phones and fobs unnecessarily close to the lock when inside the home Restrict access to your Kevo lock s back panel and routinely check your settings to ensure they have not been altered without your knowledge Protect the password to your Kevo app and web portal accounts When sending an eKey always double check that you are sending it to the correct recipient Protect and restrict access to your smartphone so that your app settings cannot be altered without your knowledge Enable the Kevo app s security passcode so that your app settings cannot be altered without your knowledge When sending eKeys be aware of the difference between an Admin user and other users in the system an Admin user can send disable and delete eKeys If your smartphone is lost or stolen use the Kevo web portal www mykevo com t
4. you and close the door Make sure there is a clear line of sight between the lock and the fob Touch the deadbolt rose Press and release the enroll button on the fob with a ballpoint pen to wake it up When the fob s LED flashes green the fob is awake and ready for use deadbolt rose q Note The deadbolt rose is the metallic surface behind the light ring LED enroll button ZA Download the app and set up your smartphone Follow the instructions inside the app to create an account enroll your first smartphone and send eKeys to family and friends Download the Kevo app at www kwikset com kevo app or scan the QR code below 8 Re key the lock if needed and install the battery cover Re key the lock if needed IMPORTANT Remove battery Re key the lock to work with pack before re keying your existing key See the supplied SmartKey Re key instructions for more Reinstall battery pack information Did the latch bolt bolt retract and extend on its own The Status LED will flash red and green and the lock will beep Press and release the Program button again The latch bolt will retract and extend on its own o Door handing process Remove battery pack was successful wait 15 seconds Proceed to next step then attempt the status LED after latch bolt stops process again moving The light ring will spin blue then flash amber once and you will hear one
5. and you will hear one beep if switch 3 is on CAUTION With this feature enabled it is possible to lock yourself outside if you don t have an enrolled smartphone Kevo fob or standard key with you A complete audio visual chart of all the lights and sounds in the Kevo system is available in the online Troubleshooting Guide at www kwikset com kevo support Blue Spinning and Shutting Off Kevo was unable to establish a connection with your device or Kevo detected the device on the inside of the door If this happens frequently see the online Troubleshooting Guide Magenta Flash Your device is outside of activation range Touch the deadbolt rose again As of software version 1 2 3 your device will automatically calibrate so that Kevo s inside outside sensor adjusts to your device s new location You may need to touch the lock a few times for it to learn your device s new location Red Flash The lock has detected an unauthorized device within activation range Kevo will not unlock If this happens frequently see the online Troubleshooting Guide Top Two LEDs are Solid Red The AA batteries in the Kevo interior are low and need to be replaced Bottom LED is Solid Red The fob battery is low and needs to be replaced See the online Troubleshooting Guide for instructions Side LEDs Flashing Red The deadbolt has jammed Check your door for alignment and make sure the latch bolt can operate smoothly Important Safeguards
6. beep The door will lock Touch the deadbolt rose again The light ring will spin blue then flash green twice and you will hear two beeps The door will unlock o If your fob is unable to communicate with the lock see the online Troubleshooting Guide at www kwikset com kevo support When using your phone to lock and unlock the door make sure the phone is on Bluetooth is enabled and the Kevo app is running in the background You may hold the phone in your hand pocket bag or purse as long as there is a clear line of sight between the lock and the phone Press the deadbolt rose to lock and unlock the door D Install battery cover Kevo at a Glance 1 Deadbolt rose lay 3 Light ring Kwikset 2 SmartKey m D tool hole 4 Keyway Ww 6 Back panel button 8 Turnpiece Sd i 5 Reset button 9 Calibrate button 7 Program I 10 Switches g l1 Status LED Switches E4 9 123 4 ON Switch 1 Status LED Door lock status LED blinks every 6 seconds ON position is factory default Switch 2 A Triple Touch Lock See Triple Touch Lock OFF position is factory default OFF Switch 3 Audio Beeping sound is heard during programming and normal operation ON position is factory default Switch 4 Future Feature Error Notifications Touch Kevo anywhere on the 8 metallic surface behind the light ring to lock and unlock Insert your SmartKe
7. evice in your Kevo system will automatically calibrate to enable this sensor as of software version 1 2 3 For more information on calibration go to www kwikset com kevo support Kevo App Passcode Kevo features an optional added security passcode that you can enable inside the app to be used in addition to the app s password Enabling the passcode will require you to enter a 4 digit PIN whenever you access the app and it protects your Kevo account against unauthorized changes when your phone is unlocked History Log A history of the lock s activity may be viewed through the Kevo app or by logging into the web portal www mykevo com System Reset A WARNING Resetting your Kevo system will restore your lock to factory default settings and delete all smartphones and fobs from Kevo s memory If you wish to perform a system reset press and hold the Reset button on the back panel for 10 seconds until the lock beeps and the light ring flashes red Phones After a system reset you will need to re enroll and your Owner phone You will still be able to send eKeys at no charge to anyone who previously had an active eKey at the time of reset Fobs After a system reset all fobs will need to be re enrolled See the online Troubleshooting guide for instructions Need Help If you have questions our highly trained Kevo Support team can provide you with the assistance you need 1 800 327 5625 1 800 327 5625
8. h center hole then push cables into side hole center side hole Ole Keep parallel to edge of door Insert key and test latch If latch does not extend or retract smoothly G adjust screws Q R Remove key when finished and make sure the latch bolt is fully extended Connect the thinner cable Ensure tight cable connection Connect the thicker cable Ensure tight cable connection Tuck the thinner cable s connector behind the backplate as indicated by the sticker on the interior assembly Jo Lay thicker cable flat against the interior housing og Push the turnpiece shaft onto the torque blade Avoid pinching the excess thinner cable by pulling it away from the torque blade S 2 Note Turnpiece may not rotate smoothly until after step 5 Gi Perform door handing process This step will teach the lock the orientation of your door and is crucial for lock operation Install 4 AA batteries in the battery pack Make sure the door is open Insert the battery pack while pressing and holding the Program button Release the button when the battery pack is all the way inside the lock interior SH 0 i M A A Ensure correct polarity For best results use new non rechargeable Alkaline batteries only 6 Wake up and test Kevo fob Bring your fob and standard key outside with
9. o disable it If a fob in your Kevo system is lost or stolen reset your lock to delete it from memory A CAUTION Prevent unauthorized entry Because anyone with access to the back panel can change your Kevo lock s settings you must restrict access to the back panel and routinely check your settings to ensure they have not been altered without your knowledge A CAUTION As with any radio based technology it should be noted that the accuracy and reliability of the Kevo lock s inside outside sensor cannot be guaranteed Users should not rely solely on the Kevo lock s sensor for security purposes and should always use caution Kwikset assumes no responsibility for incorrect results or damages resulting from the use of the Kevo lock s sensor Certain home configurations may impede the Kevo lock s sensor more than others Example Your home office is located next to your entryway and part of the office extends past the front door jutting into the front yard If your device is being actively used in that office extension the Kevo lock s sensor could possibly detect the device as being outside of your home while that device is in active use A WARNING This Manufacturer advises that no lock can provide complete security by itself This lock may be defeated by forcible or technical means or evaded by entry elsewhere on the property No lock can substitute for caution awareness of your environment and common sense Builde
10. r s hardware is available in multiple performance grades to suit the application In order to enhance security and reduce risk you should consult a qualified locksmith or other security professional Kevo Compatible Devices Smartphones and Smart Devices A Kevo compatible smartphone or other mobile E El internet connected device or tablet must have Bluetooth Smart Ready Bluetooth 4 0 and an app specific to the device must be installed Find out if your device is compatible at www kwikset com kevo devices Kevo Fob A Kevo Fob is a Bluetooth device that provides the same touch to open convenience as a smartphone Additional fobs can be purchased as needed Up to eight fobs can be enrolled in a single Kevo lock A single fob can be enrolled in up to 25 different Kevo locks Note You may choose to use only Kevo fobs only smartphones or a mix of both in your Kevo system Standard Key Always make sure you have access to your standard key Advanced Features Inside Outside Notifications Sensor The Kevo app can send notifications when the door is locked and unlocked by eKey holders You can choose to receive the system s default notifications or set up custom notifications to monitor a specific user or time frame The Kevo lock features a sensor that can tell if your device is inside or outside your home to help prevent your door from being unlocked by unauthorized users while your device is inside Each d
11. the door hole a YES No adjustment is required Proceed to next step ma N YES Latch A Latch A2 chiseled Use latch A Extend the latch bolt as shown a ay a a Rotate latch face as shown to extend latch door frame 3 Install exterior assembly What is the diameter of the hole in the door Diameter is 2 1 8 54 mm Diameter is 1 1 2 38 mm 2 118 ARN w F is required for installation Install F on E W F is not needed for installation Discard F E What is the thickness of your door Door is 1 3 8 35 mm thick Door is 1 3 4 44 mm thick 1 3 4 44 mm Use the longer gold screws 7 a Use the shorter silver screws C D R 4 Install interior assembly Remove battery cover and battery pack from interior assembly Make sure turnpiece is in the vertical position Remove t interior cover Remove t battery pack Do not install batteries yet D O OJ 2 Route the thinner cable around the outside of the 2 thicker cable s square connector turnpiece shaft Install exterior assembly and mounting plate a Locate mounting plate K Note It may be on the back of the interior assembly L Cables go underneath latch Route cables throug
12. y tool here when rekeying your lock to work with your existing key 9 Changes color to Kevo Reference Guide Use to manually lock and unlock Kevo from the inside When the turnpiece is vertical Kevo is locked When it is horizontal Kevo is unlocked Use to manually calibrate phones and fobs communicate with you 10 Use to enable and disable the Insert your standard key here A Only use to reset Kevo to delete all eKeys and fobs See System Reset for more information Where all the programming Status LED Triple Touch Lock and Audio 11 Communicates whether the door is locked or unlocked and flashes red for a low battery alert Can be turned on and off by Switch 1 features are located Use to enroll phones and fobs Triple Touch Lock This is a convenient feature that allows you to lock the door from the outside without the use of a smartphone or fob You might use Triple Touch Lock if you are using only a standard key in your system but wish to lock the door by touch if your smartphone or fob is disabled or if you have a visitor in your home that will leave and lock the door behind them Note This feature is OFF by default To enable it flip Switch 2 to the ON position then lock or unlock the door by touching the deadbolt rose To lock the door with this feature touch the deadbolt rose three times pausing briefly between each touch The light ring will spin blue flash amber
Download Pdf Manuals
Related Search