Home

USER MANUAL WEIGHT INDICATOR

1. value HELP key ZERO y Decrease of a digit while entering a value MODE gt Scrolls the digits to the right while entering a value PRINT Confirms the entered value or enters the displayed step 3590EKR 3590EXP 3590EXT series indicator E AF08 02 12 01 EN U 4 1 6 2 18 KEY INFRARED REMOTE CONTROL With this type of remote control the functioning of the keys will be as described in the following table The remote control can be programmed so that it will emulate the Tare key instead of the 2nd F key of the indicator and the function keys from F1 to F10 instead of the numeric keys numeric key 1 for F1 numeric key 2 for key F2 etc see below the configuration details FUNCTION OF THE KEYS KEYBOARD KEY OR FUNCTION EMULATED Fn Fn key 2nd F 2nd F key or Tare function see configuration below C C key Entry of digits or emulation of F1 F10 keys see HOMERIC AETS configuration below TARE 4 Tare function or increase of a digit while entering a value i HELP key ZERO v Zero function or decrease of a digit while entering a value MODE gt Scrolls the digits to the right while entering a value PRINT Confirms the entered value or enters the displayed step To execute this configuration press at length the Fn key on the remote control the configuration of the 2nd F key is proposed select the desired key that should be simulat
2. aT The weight is unstable Icon viewable only when the DIAGNOSTICS PERIPHERAL UNITS function is active see section DIAGNOSTIC PERIPHERALS t Ke aLb Unit of measure in use ton kilogram gram pounds 828 0862 Active scale see section SCALES MANAGEMENT Icon viewable only when the DIAGNOSTICS PERIPHERAL UNITS function is active see section DIAGNOSTIC PERIPHERALS Respectively indicates the status of an output as non active or active Icon viewable only CN when the DIAGNOSTICS PERIPHERAL UNITS function is active see section DIAGNOSTIC PERIPHERALS r Respectively indicates the status of an input as non active or active Icon viewable only 21 when the DIAGNOSTICS PERIPHERAL UNITS function is active see section DIAGNOSTIC PERIPHERALS Ta Rg Serial communication with external device Icon viewable only when the DIAGNOSTICS AM PERIPHERAL UNITS function is active see section DIAGNOSTIC PERIPHERALS a F F Battery charge level see section BATTERY LEVEL INDICATION el Active during the configuration of the date and time Locked keyboard see section DISABLING THE KEYBOARD G In the HELP menu these respectively indicate whether a key is unlocked or locked in the SETUP level lt lt En KEYS gt gt step see section HELP MENU Fn The Fn key has been pressed ze The 2nd F key has been pressed E El Transmission of the data
3. confirm with the ENTER key to print the entire database which shows all the relative fields for each stored data 11 5 DATA SELECTION DESELECTION To select a stored item one can proceed in the following ways 1 Enter the database item number using the numeric keyboard if different than the 000 storage see the following section and press F1 if data is stored in the recalled position the indicator display shows the message ITEM XXX SELECTED in which XXX indicates the number of the selected item and activates it 2 Press for an instant the F1 key to enter in the database Select the memory storage by using the arrow keys a by typing the storage number with the keyboard the LCD display shows the first corresponding DESCRIPTION line by searching the first description see section ALPHABETICAL RESEARCH 26 3590EKR 3590EXP 3590EXT series indicator E AF08 02 12 01 EN U Press ENTER to activate the item 3 Press a direct key combined to the desired article for example one can activate the article 1 by pressing directly the F6 key to do this one has to combine the function 310 to the desired key and insert a preamble value equal to the storage number to select see lt lt F KEYS gt gt step TECH MAN REF 4 Through function 311 combinable with the desired key lt lt F KEYS gt gt step TECH MAN REF it is possible to alphabetically search data by carrying out the immediate selection through
4. the following will be PIDST S 1 000kg 1 000kg 00127 000000 NOTE it s possible to read the last 131071 weighs 16 1 READING OF THE WEIGHS CARRIED OUT Through function 414 combinable with the desired key lt lt F KEYS gt gt step TECH MAN REF it s possible to read a carried out weigh first enter the rewriting number of the Alibi memory rEW id confirm with ENTER and then enter the weigh number id and press ENTER The ID is accepted only if valid If the alibi memory is empty the message EMPTY appears on the LCD display for a few instants if the ID code entered is not valid the no id message appears for a few instants and then one exits the step By entering a valid ID code the LCD display shows the following data selectable through the arrow keys y Ch X in which X is the selected channel number S sum channel uM XX in which XX is the unit of measure Gross weight value Tare weight value Press C to exit the reading state of the weighs NOTE It is possible to read the weigh carried out also through the PC serial line see the WEIGH READING serial command in the following section 16 2 SERIAL COMMANDS FOR MANAGING THE ALIBI MEMORY IMPORTANT If the serial commands are transmitted in the format lt ESC gt command lt STX gt in which lt ESC gt is the ASCII decimal 27 character lt STX gt is the ASCII decimal 02 character Also the relative answer will be l
5. It means that an advanced function is being described therefore for the technical personnel TECH MAN REF which will be further explained in the corresponding technical manual THE INSTRUMENT S DANGEROUS VOLTAGE PARTS AND THE PARTS THE USER CAN ACCESS HAVE BEEN ELECTRICALLY INSULATED 3590EKR 3590EXP 3590EXT series indicator E AF08 02 12 01 EN U 3 INSTALLATION 3 1 CASE AND DIMENSIONS ABS MODEL The indicator has an IP65 ABS case whose external dimensions are shown in the Figure It can be simply put on a table or fixed to a shelf or column available on request NOTE If the identification plate is supplied separately therefore not attached to the indicator it is advisable to attach it to the indicator in order to be able to identify the instrument 278 0000000000000000VA Figure 2 Measurements and dimensions in mm 1 RJ45 connector 3590EKR 3590EXP 3590EXT series indicator E AF08 02 12 01 EN U 2 Fixing for shelf or column mounting 3 5 Available for load cells serial lines inputs outputs 4 Power supply input STAINLESS STEEL MODEL The indicator has an STAINLESS STEEL case whose external dimensions are shown in the Figure 3 It can be simply put on a table or fixed to a shelf or column available on request NOTE If the identification plate is supplied separately therefore not attached to the indicator it is advisable to attach it to the indicator in order to be able to ident
6. 3590EKR 3590EXP 3590EXT series indicator E AF08 02 12 01 EN U HELP If pressed in some steps or functions of the weight indicator the display shows the keys and their functions specific to that state of the instrument In the numeric or alphanumeric input phase it enters in this order the following characters lt 211 84 2 110 HELP function see section HELP MENU F1 By entering a number through numerical keyboard and then pressing the F1 key one can quickly select the database item corresponding to the entered value the article must have already been edited In the numeric or alphanumeric input phase it allows to copy entered characters If pressed for an instant it allows entering the database lf pressed at length one locks and unlocks the instrument s keyboard except the C key F2 In the numeric or alphanumeric input phase it allows to stick with copied characters If pressed for an instant it allows to insert the coordinates of the active scale If pressed at length the weight visualization function with sensitivity x 10 is enabled F3 If pressed for an instant it allows to insert the number of weighs after which it will be printed and the partial total is cleared If the value to be inserted is equal to 0 the automatic printing is disabled If pressed at length one can adjust the date and time of the instrument F4 If pressed for an instant it
7. configuration equalisation calibration of the cells etc 43 3590EKR 3590EXP 3590EXT series indicator E AF08_02_12 01_EN_U 17 2 AT START UP MESSAGE DESCRIPTION LED DISPLAY LCD DISPLAY During the calibration some internal negative points have been Err 36 calculated j the calibration point is less than the zero point _ the signal is negative check the connections During the calibration some internal points less than the minimum Err 37 value have been calculated the calibration point is equal to the zero point A capacity too high in relation to the division has been set Err 39 The converter points are less than the instrument s internal In with divisions one must execute a TECHNICAL DEFAULT dFLt t no CAL parameter of the SET UP environment and carefully carry out the calibration Invalid calibration range number there is the value 0 or values Err 39 greater than 3 one must execute a TECHNICAL DEFAULT i dFLt t parameter of the SET UP environment if not already executed previously and carefully carry out the calibration The value 0 is in the range 1 parameter of the calibration one Err 40 must execute a TECHNICAL DEFAULT dFLt t parameter of the SET UP environment and carefully carry out the calibration The value 0 is in the diV 1 parameter of the calibration one Err 41 must execute a TECHNICAL DEFAULT
8. instability led is off and VALID In other words the OVERLOAD condition must not be created 7 1 2 PRESET TARE To enter the tare value with the keyboard type the desired tare value one digit at a time and press TARE The C key quickly clears the digited value The indicator automatically subtracts the entered value from the displayed weight the NET and gt T or F indicators turn on as long as it is not greater than the instrument s maximum capacity The display shows furthermore the stored tare value identified with PT Preset Tare In any case when a new Tare value is entered the preceding one is cancelled and substituted NOTE In the printout the manual tare is identified with PT Preset Tare 22 3590EKR 3590EXP 3590EXT series indicator E AF08 02 12 01 EN U 7 2 TARE FUNCTION IN AXLE WEIGHING MODE Unlike in the wheel weighing mode the tare value in the axle weighing mode can be inserted only manually and it is not subtracted from the displayed weight value but from the sum total of the totalized axles in other words the partial total By inserting a tare value the NET and gt T pilot lights will not be managed since the LED display will continue showing the sum weight of the active scales It will be possible to view the stored tare value on the LCD display see section DISPLAYED DATA To enter the tare value with the keyboard type the value including the decimal point and p
9. 000 00 Y WhEL 2 015 00 SCALE 3 X WhEL 3 013 00 Y WhEL 3 015 00 SCALE 4 X WhEL 4 013 00 Y WhEL 4 000 00 13 3 AXLE WEIGH TOTALISATION TYPE To carry out the weighing of a vehicle in the axle weigh mode carry out the following operations 1 Carry out a cycle of zero 2 Put the first axle of the vehicle onto the scales 3 Press F6 the weight of the vehicle is totalized and if enabled the weight data of the single scales and the total vehicle is printed 4 Take the vehicle off the scales Put the next axle onto the scales 6 Press F6 the weight of the next axle is totalized and if enabled the configured weight data of the single scales and the vehicle total is printed 7 Take the vehicle off the scales Repeat operations 5 6 and 7 for all the remaining axles 9 Press the F8 key the ZEROS TOTAL PARTIAL message is displayed on the LCD display press ENTER for printing and reset the total weight of the vehicle obtained from the sum of the axles or press the C key for exiting without changes al a 13 3 1 UPDATING TOTALS Every time one carries out a totalisation the partial total is increased of the weight of each totalized axle After weighing the vehicle the general total and the grand total are increased of the current partial total 13 3 2 CANCELLING LAST WEIGH If a wrong totalisation has been made it is possible to cancel the executed weigh Press the 2ndF and F7 keys the
10. 4 fourth description line up to 20 characters DESCRIPTION 5 fifth description line up to 20 characters 11 2 MODIFICATION OF DATA 1 Press the F1 key to enter data in the database 2 Select the data to be modified by using the arrow keys a by typing the storage item nr with the keyboard the LCD display shows the first corresponding DESCRIPTION line by searching the first description see section ALPHABETICAL RESEARCH Press F2 Select the field to be modified by using the arrow keys and press ENTER Modify the value and press ENTER to confirm Restart from point 4 to modify other fields or press C to return to the list of storages Restart from point 2 to modify other storage or press C to return to the weighing phase NO OF WwW wa 11 3 CANCELLATION OF DATA 1 Press the F1 key to enter data in the database 2 Select the data to be cancelled by using the arrow keys a by typing the storage item nr with the keyboard the LCD display shows the first corresponding DESCRIPTION line by searching the first description see section ALPHABETICAL RESEARCH 3 Press F3 4 The indicator requests a further confirmation press ENTER to confirm or another key to cancel 5 Press the C key to return to weighing 11 4 PRINTING DATA 1 Press the F1 key to enter data in the database 2 Once inside the database menu press the F5 key The LCD display shows the message PRINT
11. CANCEL LAST WEIGH message is displayed press ENTER to cancel the TOTAL PARTIAL of the last executed totalisation In case the vehicle has already been completely weighed and therefore the totals have been increased with the vehicle weight the cancellation deletes the total weight of the last vehicle from the GENERAL TOTAL and from the GRAND TOTAL and restores the tare of the vehicle if it has been configured earlier Press the C key to exit without making modifications 13 3 3 ENTRY OF AXLE NUMBER FOR AUTOMATIC PRINTING OF PARTIAL TOTAL By pressing the F3 keys the display displays the Aut Prn step in this step one sets the number of axles of the vehicle which will be weighed The instrument will automatically print the total weight of the vehicle as soon as all the axles set in this step have been weighed furthermore is asked if one wants to zero the total Refer to the preceding paragraph for a description of the weighing procedures For example if one needs to weigh a tractor with a trailer having a total of 4 axles one sets 4 in this step after having weighed 4 axles the vehicle total is automatically calculated printed and zeroed and the number of weighed vehicles and the relative total is increased NOTES the number of set axles remains active until it is substituted with a new value Therefore if the vehicles which will be weighed after this have the same number of axles it is not necessary to reset the value the value i
12. CoMPrn gt gt ProtoC parameter on Alibi TECH MAN REF It s possible also to transmit the string weigh ID on the PC port by setting the SEtuP gt gt SEriAL gt gt CoMPC gt gt ProtoC parameter on Alibi TECH MAN REF The string is transmitted in the same format of the string received in response to the REQUEST WEIGHT VALUE WITH WEIGH ID command described in the corresponding section The identification of the weigh takes place through the ID code a code is given to each weigh allowing finding the weigh in the database If the weight can be saved in the alibi the numeric ID will be substituted with the message NO The ID has the following format lt Rewriting number gt lt Weigh number gt Rewriting number number of 5 digits which may go from 0 to 00255 it indicates the number of complete rewritings of the alibi memory 40 3590EKR 3590EXP 3590EXT series indicator E AF08 02 12 01 EN U Weigh number number of 6 digits which may go from 0 to 131071 it indicates the weigh number in the current rewriting of the alibi memory With each storage the weigh number is increased of 000001 when this reaches the value 131071 it restarts from 000000 and the rewriting number increases of 00001 If the weigh can not be saved in the alibi the numeric ID will be substituted with the message NO For example If the weigh which has been stored is the following PIDST S 1 000kg 1 000kg 00126 131071
13. DISPLAYED DATA tr ad cere 19 4 2 5 CUSTOMIZABLE DISPLAY Mostar sais EEE TO AE E anes EAE 20 De SCALES MANAGEMEN Tisdale iaa as 20 5 1 SET THE NUMBER OF ACTIVE 20 5 2 SELECTION OF SINGLE SCALE SUM FUNCTION conti dto 20 9 9 SUM FUNCTION a a tase a a 21 5 4 SUM OF THE SELECTED 21 6 SCALE ZERO FUNCTION Sii aria aaa 22 6 1 OPERATION OF ZERO ONTHESINCLESCA 2 22 6 2 CYCLE OF ZERO ON ALL THE CONNECTED SCALES coi tdt 22 TATARE FUNCTIONS ionann a A A 22 7 1 TARE FUNCTION ON WHEEL WEIGHING MODE c co coc ii 22 7 1 4 SEMIAUTOMATIC TARE air bag era ae al eee ce eres 22 112 PRESET TARE eset iat en o ar hn dead ME ren Nana dea 22 1 2 TARE FUNCTION AXLE WEIGHING 69 23 7 3 MANUAL CALCULATED 23 TA TARE CANCELLATION 23 7 5 LOCKED UNLOCKED DISABLED 23 7 6 LIMITATION OF THE TAREFUNCTUON 23 7 1 TARE EXECUTION MODE OR DISABLING OF THE TARE 2 cg tun secon tteutien hanged iats lotes 24 8 MULTIRANGE AND MULTIDIVISION FUNCTION s ssssssssrnunnssnnennnennnnnnnnnnnnonnnnnnnnnnnnnnnnnnnnnonnnennnennnnnnnnnnnnnenunennnnnnnnnannnna 24 9 DISPLAY OF METRIC DATA MP ica di Ai aa 24 10 FILLING IN THE INPUTTE Toca iio 24 11 DATABASE in aaa aia aran 25 11 ENTERING A acces a ce that an acta came eid oe acne en eee ct TE 26 11 2MODIRICATION OF DATA a lb 26 ES CANCELLATION OF DATA fate ie e e eri nena att ad zal aa Na e e canta conse NAA 26 CARRITO A Ec 26 11 5 DATA SELES
14. E AF08 02 12 01 EN U 7 7 TARE EXECUTION MODE OR DISABLING OF THE TARE It s possible to select the tare execution mode through the setting of the SEtuP gt gt t LoCk step TECH MAN REF By setting Disable one disables all the tare operations By setting Lock or Unlock all the tare operations previously described are enabled 8 MULTIRANGE AND MULTIDIVISION FUNCTION The multi range functioning allows to subdivide the scale capacity in two or three ranges each which is up to 3000 divisions improving in this way the first range division in the dual range and the first two ranges in the triple range For example it is possible to approve the weighing system with A single range 6 kg capacity and 2 g division 3000 div Dual range 6 3 kg capacity and 2 1 g division 3000 3000 div Triple range 15 6 3 kg capacity and 5 2 1 g division 3000 3000 3000 div NOTE For the approval of the weighing system in dual and triple ranges the cell must have better technical features in comparison to the cell used for the approval in a single range This functioning is indicated by the turning on of the LED which identify the range in which one is working W1 first range W2 second range W3 third range if configured by passing to the W2 range the second range division is enabled by passing to the W3 range the third range division is enabled at this point the W1 first scale division is restored only by passing th
15. Er 8 03 When carrying out the multirange or multidivisional calibration the ranges have ee not been entered in an increasing manner RANGE 1 lt RANGE 2 lt RANGE 3 During the calibration some internal negative points have been calculated C Er 36 the calibration point is less than the zero point the signal is negative check the connections During the calibration some internal points less than the minimum value have C Er 37 been calculated dead the calibration point is equal to the zero point a capacity too high in relation to the division has been set Err 72 Calibration error a too low sample weight has been used Err 85 Operation not allowed because the instrument has not been calibrated ERROR It is shown when during the sampling phase the weight results to be unstable Err Mor UNSTABLE and therefore can not be acquired WEIGHT 1 ErPnt ErPnt During the acquisition of a calibration point a null value from the converter has been read SAVE EXITING SETUP The instrument requests the saving when exiting the set up press ENTER to f SAVE confirm or C to not continue SURE The instrument requests a confirmation before proceeding press ENTER to confirm or C to not continue Generic error Possible motives can be During the multiscale or multidivisional type of calibration ranges in Error increasing order have not been inserted RANGE 1 lt RANGE 2 lt RANGE 3 An error has taken place in the connection
16. KEYS gt gt step TECH MAN REF allowing to directly delete the content of an input text with a direct key for example F1 key to quickly delete the content of the text 0 11 DATABASE The indicator has a database with 1000 items having each five descriptions of 20 characters each item is linked to a storage number from 0 to 999 The selected item is shown on the LCD display during the weighing operations see section DISPLAYED DATA and can be printed through the relative print block Dee Database ar momen oar Ps mm ne Tae oar 25 3590EKR 3590EXP 3590EXT series indicator E AF08 02 12 01 EN U 11 1 ENTERING ITEMS 1 Press the F1 key to enter data in the database NOTE we advise to leave empty the memory storage 0 since it is used for the temporary entry see section ENTRY MODIFICATION AND QUICK SELECTION OF ITEM 000 2 Select the eventual desired data using the arrow keys with the keyboard by typing the storage item number 3 Press F1 to insert the data in the desired position or with the first free position if an already occupied position has been selected 4 One should fill in the following fields only the necessary ones are requested press ENTER to confirm e DESCRIPTION 1 first description line up to 20 characters DESCRIPTION 2 second description line up to 20 characters DESCRIPTION 3 third description line up to 20 characters DESCRIPTION
17. NUMBER OF TICKET COPIES Through function 400 combinable with the desired key lt lt F KEYS gt gt step TECH MAN REF any printout will be made various times depending on the number set in this step from 1 to 5 14 3 PRINTING OF THE HEADING It is possible to programme from the indicator or from PC 3 alphanumeric heading lines of 24 characters each which will be printed in the programmed mode until their cancellation or substitution F ModE gt gt tXt i parameter of the setup menu TECH MAN REF allows to program the heading 14 4 REPETITION OF THE LAST EXECUTED PRINTOUT By pressing in sequence the 2nd F and F5 keys the last executed printout is repeated however it s not possible to reprint any selected databases and the date time will be of the copy just reprinted NOTE If one wants to execute more than one printout it s advisable to recall function 400 see section NUMBER OF TICKET COPIES 14 5 DEFAULT PRINTING FORMATS The SEtuP gt gt SEriAL gt gt dEF Prn parameter of the set up environment TECH MAN REF allows to enable the default printouts for the TPR printer NOTE By enabling these printouts all the formatted print formats will be CANCELLED and the first 13 will be SUBSTITUTED by the standard formats which automatically will be linked to the 13 print functions 35 3590EKR 3590EXP 3590EXT series indicator E AF08 02 12 01 EN U 15 OTHER FUNCTIONS 15 1 CALCULATOR Through function 114 combina
18. PARTIAL TOTAL desired key lt lt S F 02 F KEYS gt gt step TECH MAN REF GENERAL TOTAL F9 SF 0 GRAND TOTAL F10 S F 04 WHEELS WEIGHS TOTALISATION F6 S F 05 HEADING AXLES WEIGHS TOTALISATION Automatic entry S F 06 AXLES WEIGHS TOTALISATION F6 S F 07 Automatic entry or F8 see section WHEEL WEIGH TOTALISATION TYPE VEHICLE END PARTIAL TOTAL and AXLE WEIGH S F 08 TOTALISATION TYPE depending on the weighing mode START UP PRINTOUT Automatic entry S F 09 RESULT OF THE CALCULATOR Automatic entry S F 10 S F 11 list heading for selected customer S F 12 2nd F and F6 LIST OF WEIGHS sequence single weigh selected customer SF 13 sector end selected customer 34 3590EKR 3590EXP 3590EXT series indicator E AF08 02 12 01 EN U TO LINK THE FORMAT e Recall function 200 combinable with the desired key lt lt F KEYS gt gt step TECH MAN REF Fn 200 S F 01 gt F 01 e The LCD display shows S F XX in which XX indicates the number of the function from 01 onwards to which the print format is linked e Select the print function for example S F 01 through the arrow keys and press the ENTER key e Once entered the display shows XX in which XX indicates the number of the format to be linked e Type the format number and press ENTER NOTE In order to no link any format to a vector one should enter the number 00 14 2
19. alarm has a delay of about three seconds from the detection of the exceeding inclination See the electrical connection scheme TECH MAN REF for the connection of the device 4 2 4 DISPLAYED DATA The data is displayed on up to three lines their visualisation depends on the weighing type and the number of active scales By pressing in sequence the 2nd F and F9 keys one will scroll through the following visualisations in this order NUM VISUALIZATION WHEEL WEIGHING AXLE WEIGHING l W S14 1000 S2 1000 A S1 1000 S2 1000 0 Active scales Active tare PT ETE S3 1000 S4 1000 Wi S1 1000 S2 1000 A S1 1000 S2 1000 1 Fret descrpt First description data selected ARTICLE S3 1000 S4 1000 ere lst 100052 1000 51 100082 1000 combination see section SUM OF THE SELECTED Be 100054 1000 SCALES In the wheel weighing mode Active scales and Barycentre Coordinates W S1 1000 S2 1000 A S1 1000 S2 1000 In the axle weighing mode ax 00001 2000kg 3 7 Active scales and number of i weighed axles and accumulated S3 1000 S4 1000 total gross weight when one is finished with the vehicle the tare is subtracted from the total if it is present Active scales A s1 100052 1000 fa s1 1000952 1000 a Number of vehicles weighed vtor 00001 4000Kq_ VOT 00001 4000Kg and the total net weight accumulated S3 1000 S4 1000 3590EKR 3590EXP 3590EXT series
20. arrow keys and press ENTER 3 Carry out one of the operations described in the previous sections 11 8 HELP By pressing HELP key inside the archive the list of command that can be used and their meaning is shown The list scroll down automatically by pressing arrow keys F6 and F7 a is possible to proceed manually 27 3590EKR 3590EXP 3590EXT series indicator E AF08 02 12 01 EN U 12 DATABASE ACCESS PASSWORD In the SETUP F ModE gt gt dtb PWd parameter TECH MAN REF one can set a password for access to the databases A password will be required only when one wants to insert modify or delete an element of the file for a moment the LCD display shows the message USER PRESS KEY afterwards it will be no longer possible to make changes to the database To access the complete menu e Press any key DURING THE VISUALISATION OF THE USER PRESS KEY the instrument requests the entry of the password a number will appear e Enter the password and confirm with ENTER e fone does not know the password one should give the random number to the manufacturer who will give a password valid ONLY FOR THAT RANDOM NUMBER 13 WEIGHING AND TOTALISATION PROCEDURES 13 1 TOTALISATION TYPES The 3590E weight indicator in the AF08 version allows to weigh vehicles with 2 or more wheels through two different totalisation modes by pressing the 2ndF and F3 keys one after the other it is possible to select the following totalisation modes W
21. keyboard full scale value zero scale available on the 3590EXT IO value and minimum value from 0 to 10 Vdc or from O to 20mA the maximum version resistance applicable on the output current is 350 Ohm and the minimum resistance applicable on the output voltage is 10 kohm THE INSTRUMENT S DANGEROUS VOLTAGE PARTS AND THE PARTS THE USER CAN ACCESS HAVE BEEN ELECTRICALLY INSULATED 3590EKR 3590EXP 3590EXT series indicator E AF08_02 12 01_EN_U 2 1 ACCESSORIES AVAILABLE On the indicator it is possible to implement internal and external modules used to increase interfacing possibilities For example the number of usable outputs various types of printers in order to have a report of the weighs made or a giant display in order to better see the weigh operations Also one can connect a PC in order to simply program the instrument through Dinitools or in order to have a complete management of the weighs Contact the reseller for the list of the available hardware and software accessories 2 2 SYMBOLS USED Below are the symbols or texts used in the manual to recall the reader s attention and on the instrument to recall the user s attention ATTENTION Only qualified personnel must perform this operation ATTENTION This is referred to working on energized lines only qualified personnel must require or perform this operation 66 CE CONFORMITY CID IDENTIFIES THE CLASS OF PRECISION 7
22. mode on the gross weight 15 5 1 9 SET POINT ON THE GRAND TOTAL By selecting this functioning mode the output function is enabled on the sum between the NET weight on the scale and the accumulated net grand total the entry of the SET POINTS and the specifications are the same as the functioning mode on the gross weight 15 5 1 10 SETPOINT ON THE NEGATIVE NET WEIGHT Functioning with hysteresis rL iSt HYSTERESIS parameter set as iSt on By selecting this functioning mode the outputs function on the NEGATIVE NET weight is activated one enters two NEGATIVE SET POINTS for each output a DISABLING one which when the NET weight is greater than it disables the appropriate output an ENABLING one which when the NET weight is lower or equal than it it enables the appropriate output The entry and specifications are the same for the functioning mode on the gross weight A OUT1 STATUS lt gt ENABLED lt gt DISABLED gt S1 on S1 Off NET WEIGHT 38 3590EKR 3590EXP 3590EXT series indicator E AF08 02 12 01 EN U Functioning without hysteresis rL iSt HYSTERESIS parameter set as iSt oFF The operating mode is the same as the previous one except that just one SETPOINT is entered for each output S 1 on for this purpose the access to the S 1 oFF parameter is inhibited The entry and specifications are the same for the functioning mode on the gross weight 15 5 2 EXCLUSIVE FUNCTIONING MODE
23. on the scale is included in the percentage configured in the lt lt 0 PErC gt gt TECH MAN REF step it is zeroed If the weight is not within this range it will not be cleared and an error sound is emitted In the end the indicator automatically returns to the display of the weight present on the scale 6 2 CYCLE OF ZERO ON ALL THE CONNECTED SCALES If the automatic zero has been set at the start up in the SEtuP gt gt ConFiG gt gt PArAM gt gt Auto 0 step of the setup TECH MAN REF by pressing the combination of the 2ndF and ZERO keys a zero cycle is executed in all the current scales 7 TARE FUNCTIONS The tare functions depend on the selected totalisation type 7 1 TARE FUNCTION ON WHEEL WEIGHING MODE 7 1 1 SEMIAUTOMATIC TARE By pressing the TARE key one tares any weight which is on the scales the LED display shows tArE for an instant and then 0 net weight the NET and gt T LED turn on the stored tare value is shown on the LCD display see section DISPLAYED DATA NOTES 1 The LCD display shows the gross weight value and the stored tare value identified with PT Preset Tare In the printout the tare is identified with PT Preset Tare 2 The tare function in the wheel weight mode will be carried out only if the weight shown on the LED display is the sum weight of the active scales the weight present on the scales is of AT LEAST FIVE DIVISIONS AND IS STABLE
24. selection modification phase NOTE e The entered texts remain in storage until these are substituted or cancelled e If no text has been configured the pressing of the F4 key has no effect e Through specific print macros it s possible to automatically cancel the contents of all the texts right after their printing TECH MAN REF e For information on the entry of the alphanumeric texts see section ENTERING ALPHANUMERIC TEXT QUICK MODIFICATION OF AN INPUT TEXT 1 s possible to access directly to the modification of each of the input texts from 0 to 9 by associating to a key the corresponding function from 121 to 130 see lt lt F kEyS gt gt step TECH MAN REF Furthermore the external PC keyboard allows to enter a numeric or alphanumeric string max 32 characters and then press the key combined to the desired input text to quickly enter the text without having to confirm with ENTER key see section INDICATOR CONNECTED TO PC KEYBOARD QUICK DELETION OF AN INPUT TEXT By linking the function 131 to a direct key it s possible to delete the content of an input text when this key is pressed one is asked to enter the number of the text to be deleted for example by confirming the value 0 the content of the text 0 is deleted By confirming the value 99 the content of all the input texts is deleted It s also possible to link the number of a specific input text to the function 131 preamble function in the lt lt F
25. the ENTER key To deselect a selected item one can proceed in the following ways 1 Press for an instant the F1 key to enter data in the database and press 2nd F 2 Press a direct key combined to the function of data deselection to enable this function one has to combine the function 310 to the desired key and insert a preamble value equal to 9999 see lt lt F KEYS gt gt step TECH MAN REF Before of the deselection a confirmation is requested press ENTER to confirm or another key to cancel 11 6 ENTRY MODIFICATION AND QUICK SELECTION OF ITEM 000 It s possible to quickly enter or modify a temporary memory storage in order to avoid the filling in of the database 1 Press in sequence the 0 NUMERIC and F1 2 The indicator allows directly filling in the memory storage 000 see section ENTERING ITEMS for the data to be filled in 3 Upon confirmation with ENTER of the last data the item will automatically be selected NOTES Upon each entry the item 000 will be overwritten 11 7 ALPHABETICAL RESEARCH The access to the ALPHABETICAL RESEARCH is possible in the following 2 ways 1 by pressing the F1 to access the database and by pressing the F4 key or 2 through function 311 combinable with the desired key lt lt F KEYS gt gt step TECH MAN REF To search an item 1 Enter the desired characters in the first description of all the data 2 Select the desired storage item in the result list using the
26. the maximum number of characters has been reached the indicator emits an acoustic signal and the cursor remains in that positions In the updating of a text if the cursor is at the beginning of the text and the first key pressed is C or a character number key all the entered characters will be deleted Function of the keys Switches the writing mode from numeric nuM to characters ChAr F5 In the nuM mode one enters just the numbers while in the ChAr mode one can enter all the characters of a key The last writing mode selected is stored by the instrument If pressed for an instant it cancels the written characters first the characters that follow the cursor are cancelled than those that precede it one at a time If pressed at length it deletes all entered characters With empty text it exits the entry phase without confirming SHIFT It enters a space in the middle of a text 3590EKR 3590EXP 3590EXT series indicator E AF08 02 12 01 EN U HELP If pressed a few times it allows entering the following characters lt gt amp 0 In characters mode ChAr by pressing once a space is entered by pressing twice it enters the 0 character In characters mode ChAr pressed repeatedly it allows to enter the following symbols _ 1 2110 11 o8 lt 0E21 MS gt 0e2 2aY 8 0 7 0 7 UT 10 hhh d 4 Mo
27. 35 14 3PRINTINGOFTHEHEADINO ct a o a lod 35 14 4 REPETITION OF THE LAST EXECUTED 61 35 14 5 DEFAULT PRINTING FORMA Salta tias dea 35 13s OTHER FUNCTIONS iras a dd duis as 36 15 1 CALCULATOR APA ott o E 36 15 2 DISPLAY OF NET WEIGHT WITH SENSITIVITY X 10 for testing use during calibration 36 W523 Se DING DATE ETM riarann a e ea 36 15 4 NET RUSS MA Si io Peery ene E 36 19 5 oe T POINTE FUNCTION a dd T e aio le atti ts 37 15 5 1 1 8166853 37 15 5 2 EXCLUSIVE FUNCTIONING 69 39 15 6 DIAGNOSTIC PERIPHERALS caia cas 39 195 COM DATADIAGNOS TIG eniaint neinna ara ga ie a e ee 40 40 16 1 READING OF THE WEIGHS CARRIED 41 16 2 SERIAL COMMANDS FOR MANAGING THE ALIBI MEMORY ssississssisssiesssiessirssrissriesninnsrinsnirsnrrsrrnrrennrrennrens 41 16 2 1 REQUEST WEIGHT VALUE WITAWEIGHND rai 41 16 2 2 S RING FORMAT WEIGH TID xt chats aide til siste adi 42 16 2 3WElGH READING lies 42 16 2 4 ALIBI MEMORY CANCELLATION only with non approved instrument 42 I7 MESSAGE D a a iaa oe 43 1VINSIDE TRE SET UP OR MENU a O aN 43 ALAS TARTA 44 A ieia a E A E E R a E EO a 45 DECLARATION OF CONFORMI iii ia aaa 46 A RR 46 3590EKR 3590EXP 3590EXT series indicator E AF08 02 12 01 EN U 1 INTRODUCTION This manual was created to help you install and learn all about the functional possibilities of the purchased indicator The instrum
28. By setting the SEtuP gt gt outPut gt gt r ModE parameter on EXCLuS one configures the exclusive use of the outputs The check is made on all the set outputs starting from the last one OUT 16 to the first one OUT When one of these is enabled the check on the previous ones is excluded By selecting this functioning mode and setting the set points in increasing order one can create outputs activation ranges Example RELAY SETPOINT ACTIVATION RANGE rL 1 1 000 kg From 1 000 to 1 999 rL 2 2 000 kg From 2 000 to 2 999 rL 3 3 000 kg From 3 000 to 3 999 rL 4 4 000 kg From 4 000 onwards In this case if the weight reaches 2 500 kg ONLY THE rL 2 OUTPUT IS ENABLED if the weight reaches 4 500 kg ONLY THE tL 4 OUTPUT IS ENABLED 15 6 DIAGNOSTIC PERIPHERALS Through function 118 combinable with the desired key lt lt F KEYS gt gt step TECH MAN REF one enables the diagnostic peripherals function The display shows Without expansion board or if the expansion board is not detected With expansion board STATUS DESCRIPTION ANALOGIC OUTPUT A O Analogic output value express in percent OUTPUTS OUT Status output non active 2 or active 8 INPUTS IN Status input non active H or active 1 RO A eres The serial communication is active with external device Status of the weight WEIGHT with unloaded scale MU with unstable weight SCALE Number of the active scale exa
29. HEEL WEIGHING functioning mode which allows to know the vehicle weight through a single weigh the system is made up of a number of platforms equal to the number of resting points of the vehicle that is to be weighed wheels axles etc The display simultaneously shows the weight of the single scales the total weight sum and the barycentre coordinates if configured AXLE WEIGHING functioning mode which allows to weigh a vehicle through the acquisition and totalisation of each single axle While weighing the instrument simultaneously shows the weight of the single scales and the accmulated axle total In both functioning modes the weight of each vehicle can be printed and stored for subsequent verifications Furthermore there are 2 total levels automatically increased at the end of each weighing operation of the vehicle which may be cleared and printed independently from each other 13 2 WHEEL WEIGH TOTALISATION TYPE In order to weigh a vehicle in the wheel weigh mode carry out the following operations 1 Carry out a cycle of zero see chapter CYCLE OF ZERO ON ALL THE CONNECTED SCALES 2 Place the vehicle on the scale and wait for the weight stability in order to read the weight on the display 3 F6 key for executing the totalisation of the vehicle and the relative weight data is printed 4 Take the vehicle off the scale 13 2 1 UPDATING TOTALS Every time one carries out a totalisation the partial total is update
30. HON DESELECTON quis e ti cia 26 11 6 ENTRY MODIFICATION AND QUICK SELECTION OF ITEM O00 oocciocicicciciononicicncnionocnconconononnnoroo coronan 27 11 7 ALPHABETICAL RESEARCH econ 27 3590EKR 3590EXP 3590EXT series indicator E AF08 02 12 01 EN U 10 15 O un A A A chen E cant E batatanenannes 2 12 DATABASE ACCESS PASSWORD vies arras 28 13 WEIGHING AND TOTALISATION PROCEDUREG ccccssssesssesssssssersesssseseesscsceesesessieassnseneseoneceneeneteannaneaseneenaees 28 13 1 TOTALISATION Ty PES cir ea iris dia 28 13 2 WHEEL WEIGHASTOTALISATION PE de 28 18 21 UPDATING TOA e td s ed 28 13 2 2 CANCELLING LAST WES ads 28 13 2 3 ENTRY OF COORDINATES FOR CALCULATING THE BARYCENTRE OR CENTRE OF GRAVITY 28 13 3 AXLE WEIGH TOTALISA ION 30 133 PUPDATING TOTALS Godall tadas pad 30 19 32 CANCELLING LAST WEST ets 30 13 3 3 ENTRY OF AXLE NUMBER FOR AUTOMATIC PRINTING OF PARTIAL TOTAL eccna 30 13 4 SET TOTALISATION 1 31 13 5 REENABLING THE PRINTING AND VW WEI Otra ida 31 13 6 VISUALISATION AND CLEARING OF THE ACCUMULATED 01415 cece eeeeeeneeeteestensnseneeetenaneanees 31 13 7 PROGRESSIVES sd a ais rita 32 1971 PROGRESSIVE DI Sa ie 32 13 2 TIGKET PROGRESS ME a Oo 32 131 LOTPROGRESSI Bss ds td cis E 32 14 PRINTOUTS aia A A A a DIOS 32 14 1 LINKING OF THE FORMATS TO THE PRINT FUNCTIONS occiciciocicionicoioccoioronocooriornonocoo coronan coronaria 34 14 2 NUMBER OF TICKET COPIES csi corp
31. ISATION Programmable printout After a totalisation of a vehicle made with the F6 key the printing of the linked format is executed See WHEEL WEIGH TOTALISATION format for the functioning details with APPROVED or NON APPROVED instrument AXLE WEIGH TOTALISATION HEADING Programmable printout If a format is linked to the AXLE WEIGH TOTALISATION HEADING function the beginning of the axle weighing procedure executed with the F6 key will cause the printing of this format and then the format linked to the AXLE WEIGH TOTALISATION function VEHICLE END PARTIAL TOTAL Programmable printout If a format is linked to the VEHICLE END PARTIAL TOTAL function this format will be printed at the end of the of weighing a vehicle LIST OF WEIGHS Programmable printout To carry out this function press the 2ndF and F6 keys The 3 linked formats are printed in other words the printing of all the weighs list To clear the weighs list one must reset the total general link the 409 code to the desired key TECH MAN REF The indicator shows the message SurE on the LED display and the ZEROS TOTAL text on the LCD display confirm with ENTER to clear the list of all the weighs NOTE The indicator keeps the LAST 3500 totalisations in storage PARTIAL TOTAL Programmable printout Through function 405 combinable with the desired key lt lt F KEYS gt gt step TECH MAN REF the resetting of the PARTIAL TOTAL and the prin
32. LE SCALE SUM FUNCTION The total capacity division corresponds to the sum of each scale capacity division The overload signalling always corresponds to each scale capacity 96 The maximum insertable tare value is always equal to the sum of each scale capacity The tare value is the same for all the scales and is only considered on the sum weight The tare function is disabled on each scale too At start up the indicator places itself on weight sum status of each active scale 5 4 SUM OF THE SELECTED SCALES The instrument allows to display the sum of the scales that one wants Through this function it s possible to insert the combination of scales of which the sum will be displayed on the LCD display EXAMPLE if one has a system of 8 platforms and one wants to display the sum of scales 1 and 2 front axle Press keys 1 and 2 one after the other Press the F7 key The LCD display will show 3590EKR 3590EXP 3590EXT series indicator E AF08 02 12 01 EN U Press the F7 key the LCD display shows Press keys 1 and 2 one after the other Press ENTER In this way the sum weight of any of the scales will be displayed on the LCD display 6 SCALE ZERO FUNCTIONS 6 1 OPERATION OF ZERO ON THE SINGLE SCALE Select the scale using the numerical keyboard using the 2ndF and the 1 2 3 4 5 6 7 and 8 keys Keep the ZERO key pressed the message Zero appears on the LED display after which If the weight
33. N REF By pressing the 2ndF key for an instant while the version is shown in the display the indicator will shown in this order XX YY in which XX indicates the instrument type YY indicates the metrological software version XX YY ZZ is the installed software version HH is the installed hardware version 08 LEGAL FOR TRADE or HIGH RESOLUTION if the instrument is APPROVED or UNAPPROVED respectively 9 XXXXX is the the g gravity value only with APPROVED instrument 3 4 TURNING OFF THE INSTRUMENT TO TURN OFF the instrument keep the C key pressed until the OFF message appears on the LED display and POWER OFF on the LCD display 3590EKR 3590EXP 3590EXT series indicator E AF08 02 12 01 EN U 3 5 TURNING ON PRINTER IN ENERGY SAVING MODE Premise the SEtuP gt gt SEriAL gt gt CoMPrn gt gt PWrPrn parameter must be set as EXtoFF or PWrint TECH MAN REF In a system where the indicator is connected to a printer both are battery powered the printer is normally maintained in STAND BY and powered only when a printout is needed This function reduces the energy absorbed by the battery when the printer is not being used If in this configuration one should power the printer to change the paper and other maintenance jobs one needs to press the ENTER and 0 keys one after the other during the weighing the LED display shows Prn on and the printer is kept on Press any key to exit from t
34. SINGLE SCALE SUM FUNCTION In order for the LED display to show the current weight on the single scale or the sum function press the 2ndF key followed by a key from 0 to 8 0 gt gt SUN function 1 gt gt Selection of scale number 1 2 gt gt Selection of scale number 2 3 gt gt Selection of scale number 3 4 gt gt Selection of scale number 4 5 gt gt Selection of scale number 5 6 gt gt Selection of scale number 6 7 gt gt Selection of scale number 7 8 gt gt Selection of scale number 8 For example with the 2ndF and the 1 keys the words SCALE 1 appear on the LED display for a few seconds followed by the value of the Weight on the selected weighing machine It s also possible to switch from one selection to the next one by pressing two times in sequence the 2ndF key 20 3590EKR 3590EXP 3590EXT series indicator E AF08 02 12 01 EN U The selected scale is highlighted on the LCD display of the instrument Selected scale EY scale 1 Other scales 2 scale 2 S3 scale 3 S4 scale 4 S5 scale 5 S6 scale 6 S7 scale 7 S8 scale 8 5 3 SUM FUNCTION SUN function allows you to perform weighing operations on each scale or on their sum The display will show Sum weight of all scales Weight of each single scale NOTES e One can select every time the single scale by pressing in sequence 2ndF and 1 or 2 3 4 5 6 7 8 keys see section SELECTION OF SING
35. T Functioning without hysteresis rL iSt HYSTERESIS parameter set as iSt oFF The operating mode is the same as the previous one except that just one SETPOINT is entered for each output S 1 on for this purpose the access to the S 1 oFF parameter is inhibited NOTES Ifall the outputs have the NONE none functioning mode the enabling of the 202 function has no effect The DISABLING SETPOINT must be less or equal to the ENABLING ones if a value greater than the ENABLING one is entered and confirmed in the DISABLING SETPOINT the indicator will set at 0 the set point until a correct value is entered If a value lower than the DISABLING one is entered and confirmed in the ENABLING SETPOINT that value is accepted but the DISABLING SETPOINT is put at 0 The 0 value is valid on both the set point values The SETPOINT check of the weight remains active on the present value even during the modification of the SET POINT until the new value is confirmed At start up the relays are managed from when the weight is displayed and these take on the configuration set in the set up environment These are not managed inside the technical set up In case of weight not valid local or from remote scale all the outputs will be disabled 37 3590EKR 3590EXP 3590EXT series indicator E AF08 02 12 01 EN U 1 5 1 2 SET POINT ON THE NET WEIGHT By selecting this functioning mode the output function on the NET weight is enab
36. TECH MAN REF While using the indicator one may incur in the WEIGHT NOT PASSED BY 0 OR UNSTAB error shown on the LCD display this means that the function which one wants to carry out must be reenabled in order to avoid accidental executions In any case one can also exclude this type of check in order to do this one should set ALWAYS in the F ModE gt gt totAL gt gt EXE tot step TECH MAN REF 13 6 VISUALISATION AND CLEARING OF THE ACCUMULATED TOTALS Each total can be momentarily viewed on the display or cleared independently through the printout linking the function corresponding to the desired step lt lt F KEYS gt gt step TECH MAN REF TOTAL FUNCTION CODE FOR FUNCTION CODE FOR VISUALISATION RESETTING PARTIAL TOTAL 404 406 GENERAL TOTAL 407 409 GRAND TOTAL 410 412 ALL SCALE TOTAL 413 partial total general total grand total By recalling one of the clearing functions the instrument requests a confirmation before proceeding with the cancellation press ENTER to clear C for continuing to accumulate It s possible to disable the confirmation request in the F ModE gt gt totAL gt gt rESEt step TECH MAN REF In case of visualisation of the total the instrument automatically exits the function after a few seconds NOTES The weight data of the cleared total will be updated only with the subsequent totalisation Clearing of the partial total provokes the i
37. URNED prepaid to the DEALER S PLACE OF BUSINESS Warranty covers all defects NOT attributable to the Customer such as improper use and NOT caused during transport If on site service is requested or necessary for any reason where the instrument is used the Customer will pay for all of the service technician s costs travel time and expenses plus room and board if any The customer pays for shipping costs both ways if the instrument is shipped to the DEALER or manufacturer for repair The WARRANTY is VOIDED if faults occur due to work done by unauthorised personnel or due to connections to equipment installed by others or incorrect connection to the power supply This warranty DOES NOT provide for any compensation for losses or damages direct or indirect incurred by the Customer due to complete or partial failure of instruments or systems sold even during the warranty period AUTHORISED SERVICE CENTRE STAMP 46
38. USER MANUAL WEIGHT INDICATOR E AF08 PROGRAM VERSION FOR WHEEL AND AXLE WEIGHING SCALE n 1 SCALE n 2 WHEEL WEIGHING SYSTEMS CENTRE OF GRAVITY SCALE n 3 SCALE n 4 E AF08 02_12 01_EN U 3590EKR 3590EXP 3590EXT series indicator E AF08 02 12 01 EN U INDEX INTRODUCTION A 4 2 MAIN TECHNICAL SPECIFICATION Sii 5 2 FACCESSORIES AVAILABLE a dd 6 E 6 Ss NST ALA THON arar dodne lada 7 3 CASE AND DIMENSIONS uuscunsdia ds ooo T 3 APOWER SUPPEY amp START U Pierinae taraig na a a aa g na bait 9 A aa a a na Aia raTa oa A ceeds ct tags coca etal EAEE OAE aia ae AEA cides ds A EEEa Ti 9 OA TTURNING OFF THE INSTRUMEN P cu pasada ot tut a aE Aa 9 3 5 TURNING ON PRINTER IN ENERGY 5 10 4 FRONT PANEL KEYS AND DISPLAYS ii i iiir a aa aaa iiaeaae iera ieden t adai pad 10 44 FUNCTION OF THE KEY tias io sa 10 4 1 1 2ndF KEY SECOND FUNCTION OF THE KESS susana id 11 4 1 2 ENTERING ALPHANUMERIC TEXT Nara ra toc 12 413 DISABLING THE KEYBOARD curs 13 4 14 E MEN es e de el 13 4 1 5 INDICATOR CONNECTED TO PC KEYBOARD cicatrices ei 13 4 1 0 REMOTE CONTRO Lironi ini ia 14 AO FUNCTION DISPLAY niaar eea seats ated raa tee ace cae A aan 17 42 STATUS INDICATORS 1 A aiaa a o AAEE raiant 17 4 2 2 BATTERY LEVEL INDICATION irris iioii nana aaa aA aaan 18 AR TIET DEVIC E ain n a O 19 4 24
39. allows filling in the free texts if configured lf pressed at length one enters the instrument s diagnostics menu F5 Commands the data transmission to the printer serial port f pressed at length one locks unlocks the tare F6 If pressed for an instant it allows to totalize the weight on the weighing system Allow to scroll forwards in the menu steps or in the parameters inside a step In the numeric or alphanumeric input phase it decrements the blinking digit F7 If pressed for an instant it allows to enter the combination of scales for which one wants to display the sum see section SUM OF THE SELECTED SCALES Allow to scroll backwards in the menu steps or in the parameters inside a step In the numeric or alphanumeric input phase it increments the blinking digit F8 If pressed for an instant it allows printing and resetting the partial total In the numeric or alphanumeric input phase it selects the digit to be modified from right to left F9 If pressed for an instant it allows printing and resetting the general total In the numeric or alphanumeric input phase it selects the digit to be modified from left to right F10 If pressed for an instant it executes the printing and the zeroing of the grand total In the numeric or alphanumeric input phase introduces a space between two characters NUMERIC KEYBOARD Entry of digits or characters Durin
40. ble with the desired key lt lt F KEYS gt gt step TECH MAN REF one enables the calculator function e ADDITION e MULTIPLICATION e SUBTRACTION Procedure Enter the first value using the numerical keyboard Press F1 to add F2 to multiply F3 to subtract the value Terminate the operation TYPE the second value and PRESS ENTER the result will be shown for a few seconds on the LED display TYPE the second value and PRESS TARE the result will be shown for a few seconds on the LED display and will be added in the addition and multiplication case or subtracted in the subtraction case to the current tare value PRESS 2nd F the NET weight on the scale will be used as a second value and the result will be shown for a few seconds on the display In the end the printing of the CALCULATOR will be executed anyway See section PRINTOUTS To disable the calculator function press the C key 15 2 DISPLAY OF NET WEIGHT WITH SENSITIVITY X 10 for testing use during calibration By pressing at length the F2 key one will view the net weight with sensitivity times 10 only in single scale weight visualisation press the C key to return to the normal visualisation NOTES With approved indicator the visualisation lasts about 5 seconds after which it s disabled The printout can only be done when the indicator has the standard sensitivity 15 3 SETTING DATE TIME By pressing at length the F3 key it s pos
41. cells LOAD CELL CONNECTIONS 6 wires with Remote Sense DISPLAY DIVISIONS 10000e 3 x 3000e for legal weighing expandable up to 800 000 for internal use with minimum signal coming from a 1 6mV Y cell DISPLAYS Red high luminosity LED indicators with six digits h 13 mm Back lit graphic 160x32 dot LCD TARE FUNCTION Subtractive possible on all capacities MEMORY DATABASE Database of 1000 items each with 5 descriptions of 20 characters SIGNALS 16 status LEDs Graphic icons on LCD display KEYBOARD Impermeable polycarbonate keyboard with 24 multifunction IP65 protection degree with membrane keys with audible and tactile feedback PARAMETER SETUP Calibration and linearity up to 8 points fully digital and programmable from the keyboard CLOCK DATE Standard feature with buffer RAM PROTECTIVE CASE ABS console IP 65 protection SERIAL OUTPUTS 2 input output RS232 ports on terminal board amp connector 1 input output RS485 port on terminal board or RS232 on amp connector INPUTS AND OUTPUTS Management of PC keyboard or barcode reader 3590EKR 3590EXP and 3590EXT 2 inputs optoisolated photo couplers 12Vdc 24Vdc 20mA max 4 outputs optoisolated photomosfets 48Vac 0 15A 60Vdc 0 15A 10 Q max 3590EXT in lO version 8 inputs optoisolated photo couplers 12Vdc 24Vdc 20mA max 16 outputs optoisolated photomosfets 48Vac 0 15A 60Vdc 0 15A ANALOGUE OUTPUT Option 16 bit analogue output configurable from
42. ct recycled helps to avoid possible negative effects on the environment and health and supports the recycling of the materials of which the equipment is made The unlawful disposal of the product by the user will entail fines foreseen by the current regulations 3590EKR 3590EXP 3590EXT series indicator NOTE FOR THE USER E AF08_02_12 01_EN_U The message TECH MAN REF will often appear in this manual this refers to the Technical Manual which may obtained by the reseller 2 MAIN TECHNICAL SPECIFICATIONS POWER SUPPLY 12 Vdc 8 24 Vdc in the IO versions with internal or external 100 240 Vac 50 60 Hz 12 Vdc adapter depending on the model 6 Vdc from rechargeable built in battery fitted depending on the model MAXIMUM POWER 16 VA OPERATING TEMPERATURE From 10 to 40 C 14 to 104 F with constant temperature CONVERTER 24 bit Sigma Delta CONVERSION SPEED up to 200 conv sec with automatic selection RANGE OF INPUT SIGNAL 0 6 mV V 3 2 mV V MINIMUM VOLTAGE PER DIVISION 0 3 uV approved instrument 0 03 uV non approved instrument TYPICAL INTEGRATION TIME 40 msec AUTOMATIC ZERO DETECTION Only in gross mode programmable at Y Y 1 2 divisions ZERO RANGE Configurable up to 50 of max load capacity AUTOZERO AT START UP Configurable up to 50 of max capacity LOAD CELL POWER SUPPLY 5Vdc 5 120mA max 8 350 Ohm
43. d with the total weight of the vehicle while the general total and grand total are increased of the current partial total 13 2 2 CANCELLING LAST WEIGH If a wrong totalisation has been made it is possible to cancel the last executed weigh Press the 2ndF and the F7 keys the message CANCEL LAST WEIGHT is displayed press ENTER to cancel from all the TOTALS the last totalisation made and decrease of one the TOTALISATION PROGRESSIVE or press the C key to exit without making modifications 13 2 3 ENTRY OF COORDINATES FOR CALCULATING THE BARYCENTRE OR CENTRE OF GRAVITY The instrument is able to calculate and print the barycentre coordinates of the vehicle which one is weighing to carry out this operation one must enter the coordinates of the centre of scales which one is using which correspond also the ones of the vehicle wheels in the unit of measure set in the TECHNICAL SET UP gt gt F ModE gt gt LEn uM default is in meters By pressing the F2 key the coordinates of the scales present are requested The number of requested decimals when entering the coordinates is set in the TECHNICAL SET UP gt gt F ModE gt gt LEn dEC default is 2 decimal places 28 3590EKR 3590EXP 3590EXT series indicator E AF08_02_12 01_EN_U Therefore by pressing F2 the following parameters appear on the display when 8 scales are connected PARAMETER MEANING VALUE TO BE ENTERED with 4 sca
44. dFLt t parameter of the SET UP environment and carefully carry out the calibration Err 98 Upon start up the indicator is waiting for the data HARDWARE ERROR software not compatible with the installed hW Err hardware the hardware expansion component is missing which allows the software to function It is shown when there is an error in the communication with the X Err C 0Y SCALE X scale Y cell check the connections and communication parameters TECH MAN REF NOTE if the Err XX error appears after the indicator start up press the TARE key to enter in the SET UP environment 44 3590EKR 3590EXP 3590EXT series indicator 17 3 IN WEIGHING E AF08_02_12 01_EN_U MESSAGE DESCRIPTION LED DISPLAY LCD DISPLAY WEIGHT UNDER It is shown in the LCD display when one tries to print or totalise with 20 DIVISIONS the 0 or negative weight NO ZERO CROSS OR Printing or totalisation not possible without having the weight pass by INSTABILITY the net zero or by instability ae ss Turning off of the instrument through the key see section TURNING ORES POWER OFF OFF THE INSTRUMENT OUT CAPACITY The weight is 9 divisions above the Maximum Capacity Approved instrument the weight is under the gross zero 100 OUT CAPACITY Gvisions f Non approved instrument the weight is under the gross zero tee ee capacity 9 divisions ZEro Executi
45. e gross weight is negative or unstable lt CR o CRLF gt Terminator ASCII 13 and ASCII 10 characters 16 2 3 WEIGH READING Command INALRDXXXXX YYYYYY lt CR o CRLF gt inwhich I 485 address only in the case of 485 transmission mode XXXXX rewriting number from 0 up to 255 ASCII 045 character YYYYYY ID code lt CR o CRLF gt terminator ASCII 13 and ASCII 10 characters Instrument answer INB LLLLLELLLLUV YYTTTTTTTTTTUU lt CR o CRLF gt in which II 485 address only in the case of 485 transmission mode B number of selected channel LLLLLLLLLL gross weight on 10 digits UU unit of measure YY 2 spaces in the case of null tare or semi automatic tare PT in the case of preset tare TTTTTTTTTT tare weight on 10 digits lt CR o CRLF gt Terminator ASCII 13 and ASCII 10 characters 16 2 4 ALIBI MEMORY CANCELLATION only with non approved instrument Command INALDL lt CR o CRLF gt in which Il 485 address only in the case of 485 transmission mode Instrument answer INALDLOK lt CR o CRLF gt if the cancellation has been carried out effectively INALDLNO lt CR o CRLF gt if the cancellation has not been carried out effectively 42 3590EKR 3590EXP 3590EXT series indicator E AF08 02 12 01 EN U 17 MESSAGES While using the indicator it is possible to incur into the following errors 17 1 INSIDE THE SET UP OR MENU MESSAGE DESCRIPTION LED DISPLAY LCD DISPLAY C
46. e gross zero of the scale The multidivisional functioning is similar to multirange but with the difference that a range division is enabled as soon as one enters in its range interval in other words without passing by the scale zero NOTE The selection of the range number with multirange and multidivisional functioning is made during the indicator calibration TECH MAN REF 9 DISPLAY OF METRIC DATA inFO The indicator is fitted with a function named INFO thanks to which it is possible to view the configuration metric data First range capacity first range minimum weigh first range division Second range capacity second range minimum weigh second range division Third range capacity third range minimum weigh third range division NOTES The minimum weigh corresponds to 20 net weight divisions The data of the second and third range appear only if actually configured To display the metric data Press in sequence the 2ndF and C keys The METROLOGIC INFORMATION is displayed the display will show the number of the scale the type of displayed data and its value Press the F6 key to quickly scroll the data frontwards Press the F7 key to quickly scroll the previous data backwards Press the C key to quickly return to weighing 10 FILLING IN THE INPUT TEXT The indicator offers the possibility of using 15 CONFIGURABLE INPUT TEXTS for example LOT OPERATOR SHIFT etc each made up of 16 head
47. ed by using the arrow keys and press the PRINT key to confirm and pass to the following setting the configuration of the numeric key is proposed select the desired functioning of the numeric key simulating the numbers or simulating the function keys from F1 F10 by using the arrow keys and press the PRINT key to confirm and exit the menu 4 1 6 3 6 KEY RADIO REMOTE CONTROL With this type of remote control the functioning of each key can be programmed so that it is matched to one of the available keys of the indicator This configuration must be carried out in the Setup environment in the lt lt inF rEd gt gt step TECH MAN REF after the selection of this type of remote control By pressing the HELP key of the indicator it s possible to see while weighing the list of the functions matched to the keys of the indicator and also to the keys of the remote control see section HELP MENU 3590EKR 3590EXP 3590EXT series indicator E AF08 02 12 01 EN U EXAMPLE OF CONFIGURATION USE OF MORE REMOTE CONTROLS WITH ONLY ONE INDICATOR If one works with only an indicator it is possible to use any 6 key remote control without combining it to the indicator therefore without limiting the number of usable remote controls To enable this mode one has to first select RD 6 BR in the lt lt inF rEd gt gt TECH MAN REF USE OF MORE REMOTE CONTROLS WITH SEVERAL INDICATORS IN THE SAME AREA I
48. ent is suitable for use in various weighing environments Not only does it have all the normal features of high precision scales but it also gives you the possibility to work in specific environments due to the functioning modes contained in the software implemented in the FLASH MEMORY on the internal board This makes the instrument extremely flexible and it can be used in many different industrial applications linked to weighing The double numerical and interactive alphanumerical display the alphanumerical and function keyboard allow the operator an easy and immediate use and provide the microcontroller with DATA ENTRY functions in addition to the normal weighing functions The input output allows the instrument to control various external devices to receive external commands control a printer and communicate with a personal computer or to be inserted in a network of weight indicators controlled by a PC MN WARNING Please note that this instrument is covered by a warranty and MUST NOT BE OPENED BY THE USER for any reason whatsoever Any attempt to repair or modify the unit exposes the user to the risk of electric shock and will invalidate the entire warranty If any problems are found in the unit or with the system in which it is used the fact must be communicated to the manufacturer or the dealer from whom it was purchased In any case DISCONNECT THE POWER SUPPLY before taking any action With the 6V rechargeable battery option it ha
49. f one needs to use several indicators in the same area it is possible to combine each remote control to the desired indicator in order to execute the function only on it and therefore avoid emulating the function on all indicators in use By enabling this mode it will be possible to combine up to 3 different remote controls e i for 3 different operators for each indicator To enable this mode one has to first select RD 6 in the lt lt inF rEd gt gt TECH MAN REF To link a new remote control to the indicator one has to press at length 1 and 2 keys together 3 seconds the instrument displays aut rd press the ENTER key of the indicator the new remote control is linked To remove the linking of a remote control one has to press at length 1 and 2 keys together 3 seconds the instrument displays aut rd press the C key of the indicator if the remote control was previously linked it will be removed 3590EKR 3590EXP 3590EXT series indicator E AF08_02_12 01_EN_U 4 2 FUNCTION DISPLAY During the weighing the displays are subdivided mainly in 3 sections shown in the figure below 1 SUM WEIGHT SELECTED SCALE WEIGHT see section SCALE MANAGEMENT 2 STATUS INDICATORS led pilot lights and graphic symbols 3 SCALES DATES WEIGHT see section DISPLAYED DATA 2 3 4 2 1 STATUS INDICATORS LED FUNCTION POWER Indicates the
50. g the SEtuP gt gt outPut gt gt r ModE parameter on norMAL one configures the independent use of the outputs the check is always made on all the set outputs the enabling of one of these does not provoke the disabling of the others 15 5 1 1 SETPOINT ON THE GROSS WEIGHT Functioning with hysteresis rL iSt HYSTERESIS parameter set as iSt on By selecting this functioning mode the output function on the GROSS weight is activated one enters two SET POINTS for each output a DISABLING one which when the gross weight is lower than it disables the appropriate output an ENABLING one which when the gross weight is greater or equal than it it enables the appropriate output Through function 202 combinable with the desired key lt lt F KEYS gt gt step TECH MAN REF the SET POINT values are entered DISABLING and ENABLING for each configured output The Led display shows S 1 on relay 1 ENABLING SETPOINT press ENTER enter the weight value with the keyboard and confirm with ENTER use the C key to quickly zero the current value The LED display shows S 1 OFF relay 1 DISABLING SETPOINT press ENTER enter the weight value with the keyboard and confirm with ENTER use the C key to quickly zero the current value Proceed in the same way for the following outputs if present When finished programming the set points exit with the C key OUT1 STATUS ENABLED DISABLED S10FF Ston GROSS WEIGH
51. g the weighing these enter a numeric value with which it s possible to 1 Set the tare value by pressing then the TARE key see section TARE FUNCTIONS 2 To add or to subtract to the current tare the result of the operation between two values enterable with the keyboard See the CALCULATOR section 4 1 1 2ndF KEY SECOND FUNCTION OF THE KEYS In the weighing phase by pressing the 2ndF key together with another key it s possible to execute various functions continue reading the manual for the details of the functions 2ndF F2 Allows to select the number of active scales 2ndF F3 Allows to select the type of totalisation wheel weighing axle weighing see section WEIGHING AND TOTALISATION PROCEDURES 2ndF F5 Repetition of the last printout made 2ndF F6 Prints sample list 11 3590EKR 3590EXP 3590EXT series indicator E AF08 02 12 01 EN U Clears last sample see section CANCELLING LAST WEIGH in the chapter 2ndF F7 WHEEL WEIGH TOTALISATION TYPE or AXLE WEIGH TOTALISATION TYPE 2ndF ES Net Gross weight conversion on LED display see section NET lt gt GROSS SWITCH Modification of what is viewed on the LCD display see section DISPLAYED 2ndF F9 gt DATA 2ndF F10 Sets the higher totalisation threshold 2ndF C Causes display of met
52. gh the F5 key one prints the linked format without executing the totalisation With the APPROVED instrument The printing works if there is a POSITIVE NET WEIGHT of at least 20 divisions in LOADING The printout is reenabled depending on how the F ModE gt gt rEACt parameter has been programmed in the TECHNICAL SET UP TECH MAN REF With the NON APPROVED instrument The printing works if there is a NET WEIGHT greater than zero in LOADING The simple printout does not exclude the totalisation and is always active the programming of the F ModE gt gt rEACt parameter of the TECHNICAL SET UP TECH MAN REF is not taken into consideration 32 3590EKR 3590EXP 3590EXT series indicator E AF08 02 12 01 EN U WHEEL WEIGH TOTALISATION Programmable printout After the totalisation of a vehicle is made with the F6 key the printing of the linked format is carried out With APPROVED instrument the INPUT weigh functions with a minimum weight of 20 divisions and reactivates according to how the F ModE gt gt rEACt REACTIVATIONS parameter of the TECHNICAL SET UP has been programmed TECH MAN REF in other words the weight movement or passage by zero of the weight With NON APPROVED instrument the INPUT weigh functions with a weight greater than zero and reactivates according to how the F ModE gt gt rEACt REACTIVATIONS parameter of the TECHNICAL SET UP TECH MAN REF has been programmed AXLE WEIGH TOTAL
53. his condition 4 FRONT PANEL KEYS AND DISPLAYS D F FS ESI RIB gt TSHIFT 4 1 FUNCTION OF THE KEYS In the following section and later on in the manual the keys functioning is described in accordance to how these are configured by factory It is possible to customise the functionality of the keys through the lt lt F KEYS gt gt step Turns the instrument on off 0 0 lf pressed for an instant it clears the tare value Exits the parameter without confirming and saving the modifications In the numeric input phase it quickly clears the present value If pressed for an instant it carries out the tare function See section TARE FUNCTIONS for the specific tare function depending on the selected TARE ZERO totalisation type wheel weighing axle weighing If pressed at length when viewing one scale it clears the relative gross weight if it s within the percentage configured in the lt lt 0 PErC gt gt step Fn ENTER In the alphanumeric input phase it confirms the entry made In the menu it allows to enter a step or to confirm a parameter inside a step If pressed together with the other keys it allows carrying out a specific function see section 2ndF KEY SECOND FUNCTION OF THE KEYS In the lt lt F Keys gt gt step if pressed for an instant the list of the available functions appear and it is possible to choose one of them 2nd F
54. ify the instrument 264 Figure 3 Measurements and dimensions in mm 1 RJ45 connector 2 Fixing for shelf or column mounting 3 Available for load cells serial lines inputs outputs 4 Power supply input 8 3590EKR 3590EXP 3590EXT series indicator E AF08 02 12 01 EN U 3 2 POWER SUPPLY amp START UP The 3590EXP and 3590EXT indicator is powered with 12Vdc voltage 8 24 Vdc in the IO version through an internal adapter which converts the 100 240Vac 50 60Hz mains voltage and 6 Vdc from the battery fitted depending on the model The 3590EKR indicator is powered with 12Vdc voltage through an external adapter which converts the 100 240Vac 50 60Hz mains voltage and 6 Vdc from the battery TO POWER the instrument through the 240 Vac mains or TO RECHARGE the battery insert the plug and the adapter to the 240 Vac mains socket To connect it to the power mains the safety regulations must be observed including the use of a clean line without disturbances or interference caused by other electronic equipment Version with rechargeable battery The battery inside the indicator lasts about 25 hours without the expansion board with 1 cell platform and it needs a recharging time of about 12 hours BATTERY FEATURES Material LEAD Power 4 5 Ah Voltage 6V THE BATTERY MUST BE SUPPLIED DIRECTLY FROM THE MANUFACTURER NOTE it is advisable to completely recharge it 12 hours in the first ins
55. indicator E AF08 02 12 01 EN U By linking the function to a direct key see the lt lt F KEYS gt gt step it is possible to quickly recall a visualisation by digiting with the numeric keyboard the relative number and pressing the key linked to the function Notes Default visualisation 0 4 2 5 CUSTOMIZABLE DISPLAY It s possible to customize the data displayed on the LCD display through the print format 99 see the section DISPLAY CUSTOMIZATION TECH MAN REF by using the DiniTools software By pressing in sequence the Fn and F9 keys it s possible to activate the customized visualization The default configuration for this visualization is the following one first description of the selected article contents of the input text 0 contents of the input text 1 If more than 4 lines have been programmed it s possible to scroll the visualizations by pressing in sequence the Fn and F9 keys Once that this visualization has been selected press in sequence the 2ndF and F9 keys to display again the visualisations described in the previous section 5 SCALES MANAGEMENT At start up the indicator is active on the SUM function in other words the LED display shows the weight sum of all active scales and the LCD display shows the weight of each active scale 5 1 SET THE NUMBER OF ACTIVE SCALES Press the 2ndF and the F2 keys in order to set the number of active scales that are being weighed 5 2 SELECTION OF
56. ing characters and 32 content characters When entered in the TECHNICAL SET UP for the configuration of all related parameters see F ModE gt gt tXt gt gt CFG tXt Input text configuration step TECH MAN REF these may be printed later on if programmed in the printouts or these may be used as a reminder To manually fill in the input texts it is possible to proceed in two ways 1 If one knows the memory storage position from 0 to 14 of the text to be modified type the number followed by the F4 key now enter the text and confirm with ENTER the indicator returns to the weighing phase 2 By pressing for an instant the F4 key one accesses the complete list of the texts for example 24 3590EKR 3590EXP 3590EXT series indicator E AF08 02 12 01 EN U The LED display shows in XX in which XX is the index of the free text from 0 to 14 when the LCD display shows THE HEADING on the first line of the input text or Empty if empty Use the arrow a keys to select the text to be filled in and press ENTER now one can enter the alphanumeric text in the second line of the LCD display see chapter ENTERING ALPHANUMERIC TEXT in the first line of the display the heading of the text is displayed Press ENTER to store and pass on to the following stored TEXT by confirming the last entered text one returns automatically to the weigh functioning it is possible to exit also with the C key while in the text
57. ked 6 or locked a in the lt lt En KEYS gt gt step in the lower part the description of the linked function Scroll the list with the arrow keys press the C key to exit 4 1 5 INDICATOR CONNECTED TO PC KEYBOARD It s possible to connect a PC keyboard optional used to emulate the functions of the keys of the indicator The keys are managed in the following way KEYBOARD KEY OR FUNCTION EMULATED C key Esc If pressed at start up it allows entering in the technical set up In the alphanumeric input it deletes all entered characters C key If pressed at start up it allows entering in the technical set up In the alphanumeric input it cancels first the characters which follow the cursor then the ones which precede it one at a time and Canc 13 3590EKR 3590EXP 3590EXT series indicator E AF08 02 12 01 EN U Fn key Confirms the entered value Enters the displayed step Numeric and Quick entry of a numeric and alphanumeric string through the CAPS LOCK or SHIFT key it is possible to switch from the capital letters to the lower case letters and vice versa or enter the second character corresponding to the key for example amp The entered string is shown on the LCD display alphanumeric keys SHIFT and CAPS LOCK Cursor keys Scroll the parameters ay Increase or decrease the blinking digit while entering a va
58. led the entry of the SET POINTS and the specifications are the same as the functioning mode on the gross weight 15 5 1 3 GROSS WEIGHT AT ZERO By selecting this functioning mode the output function on the GROSS weight at 0 is enabled 15 5 1 4 NET WEIGHT AT ZERO By selecting this functioning mode the output function on the NET weight at 0 is enabled 15 5 1 5 INSTABILITY By selecting this functioning mode the output function on the unstable weight is enabled 15 5 1 6 TOTALISATION By selecting this functioning mode the output function is enabled after executing a single weigh or after an output weight at the end of an input output cycle the output remains enabled until the weigh is restored in other words by the passing by zero of the net weight or by weight instability see F ModE gt gt rEACt REACTIVATIONS parameter of the TECHNICAL SET UP TECH MAN REF 15 5 1 7 SET POINT ON THE PARTIAL TOTAL By selecting this functioning mode the output function is enabled on the sum between the NET weight on the scale and the accumulated net partial total the entry of the SET POINTS and the specifications are the same as the functioning mode on the gross weight 15 5 1 8 SET POINT ON THE GENERAL TOTAL By selecting this functioning mode the output function is enabled on the sum between the NET weight on the scale and the accumulated net general total the entry of the SET POINTS and the specifications are the same as the functioning
59. les X WhEL 1 x coordinate scale 1 ALWAYS 0 Y WhEL 1 y coordinate scale 1 ALWAYS 0 X WhEL 2 x coordinate scale 2 ALWAYS 0 Y WhEL 2 y coordinate scale 2 VEHICLE INTER AXLE X WhEL 3 x coordinate scale 3 VEHICLE TRACK GAUGE Y WhEL 3 y coordinate scale 3 VEHICLE INTER AXLE X WhEL 4 x coordinate scale 4 VEHICLE TRACK GAUGE Y WhEL 4 y coordinate scale 4 ALWAYS 0 X WhEL 5 x coordinate scale 5 Y WhEL 5 y coordinate scale 5 X WhEL 6 X coordinate scale 6 Y WhEL 6 y coordinate scale 6 X WhEL 7 x coordinate scale 7 Y WhEL 7 y coordinate scale 7 X WhEL 8 x coordinate scale 8 Y WhEL 8 y coordinate scale 8 Through the F5 key it is possible print the barycentre coordinates of the vehicle which one is weighing EXAMPLE to calculate the barycentre of a 4 wheel vehicle with a weighing system having the scales arranged as shown in the figure below one must position the vehicle on the scales press the F2 key and enter the following parameters Ya INTER AXLE 19 18 SCALE 2 SCALE 3 44 16 A PAN 45 4 4 4 14 13 12 11 10 9 8 7 6 5 4 3 SCALE 1 SCALE 4 2 1 0 gt 012 3 4 5 6 7 8 9 1011 12 1314 15 16 xX TRACK GAUGE 29 3590EKR 3590EXP 3590EXT series indicator E AF08 02 12 01 EN U SCALE 1 X WhEL 1 000 00 Y WhEL 1 000 00 SCALE 2 X WhEL 2
60. lue oe When entering a value or an alphanumeric string it scrolls the digits to the right or to the left F1 F2 F10 F1 F2 F10 keys F11 2ndF key F12 TARE key The PC keyboard also allows to enter a numeric or alphanumeric string max 32 characters and then press a key to execute the corresponding quick function For example if the function 122 input text 1 configuration is combined to the F4 key see lt lt F KEYS gt gt step TECH MAN REF through PC keyboard it s possible to enter a text and the press F4 to quickly modify the input text 1 NOTE through the remote keyboard it s not possible to carry out the functions made by pressing the keys at length 4 1 6 REMOTE CONTROL Depending on the model of indicator it is possible to remotely control the instrument through one of the following types of remote controls 19 key infrared ir 18 key infrared ir or 6 key radio rd The type of remote control to be used must be selected in the Setup environment in the lt lt inF rEd gt gt step TECH MAN REF NOTE The infrared remote controls are for indoor use only 4 1 6 1 19 KEY INFRARED REMOTE CONTROL With this type of remote control the functioning of the keys will be as described in the following table FUNCTION OF THE KEYS KEYBOARD KEY OR FUNCTION EMULATED F1 F3 F1 F3 keys C C key NUMERIC KEYS Entry of digits TARE a Tare zero function or increase of a digit while entering a
61. mple il see section SELECTION OF SINGLE SCALE SUM FUNCTION and the relative weight loaded 39 3590EKR 3590EXP 3590EXT series indicator E AF08 02 12 01 EN U 15 7 COM DATA DIAGNOSTIC Through function 119 combinable with the desired key lt lt F KEYS gt gt step TECH MAN REF one enables the Com data diagnostic function The display shows In the first screen one selects the port on which the diagnostic control should be executed While in the second screen one selects the code that one wants to use for viewing the data in transit When the data on the RX and TX reception and transmission lines are correctly displayed then the functioning of the relative serial line is considered to be correct NOTE By pressing the HELP key it s possible to see the keys list used in the menu 16 ALIBI MEMORY The alibi memory allows storing the executed weighs or the weights transmitted to the PC The stored values can then be recalled by the PC serial line or directly on the indicator s LED display for a following check The data filed with each weigh or upon each weight transmission is Gross weight Sum Tare Unit of measure Number of selected scale The memorisation of a weigh takes place e Following the reception of a command through the serial line See section REQUEST WEIGHT VALUE WITH WEIGH ID e Upon the printing made with the F5 or F6 key By setting the SEtuP gt gt SEriAL gt gt
62. nstantaneous increase of the general total and grand total with the current value of the partial total Clearing of the general total involves the clearing of the next totalisation of the partial total and the clearing of the weighing list Clearing of the grand total involves the clearing of the next totalisation of the partial total and of the general total and also the clearing of the weighing list 31 3590EKR 3590EXP 3590EXT series indicator E AF08 02 12 01 EN U 13 7 PROGRESSIVES 13 7 1 PROGRESSIVE DIGITS Through function 401 combinable with the desired key lt lt F KEYS gt gt step TECH MAN REF it s possible to set the number of digits with which the TICKET PROGRESSIVE and LOT PROGRESSIVE are printed It s also possible to quickly set the number of progressive digits by entering the corresponding value through the numeric keys and then pressing the key combined with the function 401 The number of settable digits varies from 4 to 16 organised in this way if the actual digits of the total are less than the number of digits set in this step the difference is filled with some spaces ifthe actual digits are greater than the number of digits set in this step only the ones actually entered are taken into consideration counting from right to left The alignment of the total fields is on the left NOTE The number of settable digits DOES NOT INCLUDE the comma 13 7 2 TICKET PROGRESSIVE Through function 402 c
63. ombinable with the desired key lt lt F KEYS gt gt step TECH MAN REF it s possible to modify or clear the TICKET PROGRESSIVE up to 5 digits It s also possible to quickly modify the ticket progressive by entering the corresponding value through the numeric keys and then pressing the key combined with the function 402 The TICKET PROGRESSIVE is a progressive number which increments of one UPON THE FIRST TOTALISATION SUBSEQUENT TO THE CLEARING OF THE PARTIAL TOTAL 13 7 3 LOT PROGRESSIVE Through function 403 combinable with the desired key lt lt F KEYS gt gt step TECH MAN REF one obtains the clearing of the AUTOMATIC LOT up to 6 digits before carrying out the actual clearing one is asked to confirm or cancel the operation confirm with ENTER The AUTOMATIC LOT is a progressive number which increments of one UPON THE FIRST TOTALISATION SUBSEQUENT TO THE CLEARING OF THE GENERAL TOTAL 14 PRINTOUTS The instrument is fitted with 13 different print functions which may be used while weighing and of 30 print formats in other words 30 different memory storages each of which contain a programmable printout The print executed by 13 of these functions depends on the print format linked to it see the following section for the linkages The format linking function allows executing various printouts by changing the linked format each time The available functions are SIMPLE PRINTOUT Programmable printout Throu
64. on of scale zero see section SCALE ZERO FUNCTIONS tArE Tare execution see section TARE FUNCTIONS CLEAr Tare cancellation see section TARE CANCELLATION Pion Turning on printer for maintenance see section TURNING ON PRINTER IN ENERGY SAVING MODE GroSS Visualisation of the gross weight nEt Visualisation of the net weight LoCk Tare lock or enabled keyboard function unLoCk Tare lock or disabled keyboard function flashing Indicates that the battery is discharged voltage at minimum level PRINTER ERROR Error during the printing totalisation not possible or print not executed CHECK THE CTS finished USER PRESS KEY See section DATABASE ACCESS PASSWORD It is shown when there is an error in the communication with the X ERROR SX nid mn CELL Y scale Y cell check the connections and communication parameters TECH MAN REF SuM Indicates that the weight that will be displayed is the sum weight of the active scales 45 3590EKR 3590EXP 3590EXT series indicator E AF08 02 12 01 EN U DECLARATION OF CONFORMITY This device conforms to the essential standards and norms relative to the applicable European regulations The Declaration of conformity is available in the web site www diniargeo com WARRANTY The TWO YEAR warranty period begins on the day the instrument is delivered It includes spare parts and labour for repairs at no charge if the INSTRUMENTS ARE RET
65. ress TARE The C key quickly zeros the current value The LCD display shows the gross weight value and the stored tare value identified with PT Preset Tare NOTES 1 In the axle weighing functioning mode in any case the LED display shows the gross weight also in the presence of a tare 2 The LCD display shows the gross weight value and the stored tare value identified with PT Preset Tare In the printout the tare is always identified with PT Preset Tare 3 A new operation automatically cancels and substitutes the previous one only if the weighing of vehicle is done 4 The tare function in the axle weighing mode will be carried out only if the weight shown on the LED display is the sum weight of the active scales the weight present on the scales is of AT LEAST FIVE DIVISIONS AND IS STABLE instability led is off and VALID In other words the OVERLOAD condition must not be created 7 3 MANUAL CALCULATED TARE With the CALCULATOR function it is possible to add or to subtract to the current tare the result of the operation between two values enterable with the keyboard For the functioning specifications see the CALCULATOR section 7 4 TARE CANCELLATION To cancel the tare press the TARE key with unloaded platform only in the wheel weighing mode Press in sequence the numeric 0 key and TARE Press the C key in both cases NOTES The tare will be cleared only if the weigh
66. ric information of the current scale see section DISPLAY OF METRIC DATA inFO 2ndF TARE ZERO Cyclical scale zero on the active scales see section CYCLE OF ZERO ON ALL THE CONNECTED SCALES 2ndF 0 Allows switching the visualization on the sum weight of active scales 2ndF 1 Allows switching the visualization on the weight of scale 1 2ndF 2 Allows switching the visualization on the weight of scale 2 2ndF 3 Allows switching the visualization on the weight of scale 3 2ndF 4 Allows switching the visualization on the weight of scale 4 2ndF 5 Allows switching the visualization on the weight of scale 5 2ndF 6 Allows switching the visualization on the weight of scale 6 2ndF 7 Allows switching the visualization on the weight of scale 7 2ndF 8 Allows switching the visualization on the weight of scale 8 4 1 2 ENTERING ALPHANUMERIC TEXT It might be necessary while the weighing system is working to enter some alphanumerical texts such as descriptions alphanumerical messages operator number of lot customer etc To enter the characters one uses the 0 to 9 keys By pressing one of these keys a few times the characters shown on the key and other special characters will be shown on the LCD display initially the first letter in the bottom left will appear and then the other characters towards the right After digiting a character the blinking cursor after a few instants advances automatically of a position When
67. s not lost when the instrument is turned off If the set value is 0 the function is disabled 30 3590EKR 3590EXP 3590EXT series indicator E AF08 02 12 01 EN U 13 4 SET TOTALISATION THRESHOLD It is possible to establish a weight interval in between 0 and the scale capacity for executing a weigh outside this interval the operation is not accepted when the F6 key is pressed the LCD display shows the WEIGHT OUT OF THRESHOLD message for a few seconds SET WEIGHING THRESHOLD e Through the 500 function combinable with the desired key lt lt F KEYS gt gt step TECH MAN REF it s possible to access the thr hi menu Maximum Threshold Setting set the upper totalisation threshold and press ENTER e Through the 501 function combinable with the desired key lt lt F KEYS gt gt step TECH MAN REF it s possible to access the thr Lo menu Minimum Threshold Setting set the lower totalisation threshold and press ENTER NOTES By setting 0 in the maximum threshold it s possible to totalise up to the maximum capacity of the scale By setting 0 in both thresholds the functions are disabled The totalisation field is valid for all totalisation types 13 5 REENABLING THE PRINTING AND WEIGH After having carried out a weigh in order to carry out a new one the displayed weight must pass by the zero or become unstable This setting is made in the SETUP environment in the F ModE gt gt rEACt parameter
68. s to be completely recharged 12 hours in the first installation of the instrument we RECOMMEND disconnecting the battery if the instrument is not going to be used for more than 30 days In order to avoid the deterioration of the rechargeable battery In standard conditions never leave the battery partially or completely uncharged at least once a week recharge it completely In case the instrument is not used for a long period one needs to 1 completely recharge the battery before the system is switched off for the last time 2 recharge completely every 3 months Do not pour liquids on the weight indicator Do not use solvents to clean the weight indicator Do not expose the instrument to direct sunlight nor place it near heat sources Place or anchor the weight indicator and platform on a non vibrating base All the connections of the indicator have to be made respecting the rules applicable in the zone and in the installing environment Everything not expressly described in this manual has to be considered as improper use of the equipment Read carefully and apply what is described in section INSTALLATION Do not install in any area where there is a risk of explosion The crossed out wheeled bin on the product means that at the product end of life it must be taken to separate collection or to the reseller when a new equivalent type of equipment is purchased The adequate differentiated refuse collection in having the produ
69. sible to quickly access the setting from the date time of the instrument DAY gt ENTER gt MONTH ENTER gt gt YEAR gt ENTER gt HOUR gt ENTER gt MINUTES ENTER 15 4 NET lt gt GROSS SWITCH Only during the display of the sum of the weights if a tare value has been entered by pressing in sequence the 2nd F and F8 keys the displayed weight switches back and forth between the net and the gross weight NOTES With a non approved instrument e During the weight display conversion it is possible to execute any print function With the approved instrument e The weight conversion remains on the display for only 5 sec once this time has passed one returns to the normal weighing status 36 3590EKR 3590EXP 3590EXT series indicator E AF08 02 12 01 EN U 15 5 SET POINT FUNCTION The indicator is fitted with a series of 4 signal outputs used for various types of operation besides through the 1 0 expansion board optional it is possible to use another 12 In the SEtuP gt gt outPut gt gt r ConF menu TECH MAN REF it is possible to set the characteristics of each output which will be used normally open or normally closed upon direct control or weight stability with hysteresis or without the functioning mode It is also possible to set whether the enabling of the output excludes the check on the previous outputs see the SEtuP gt gt outPut gt gt r ModE parameter 15 5 1 NORMAL FUNCTIONING MODE By settin
70. t ESC gt string lt STX gt 16 2 1 REQUEST WEIGHT VALUE WITH WEIGH ID The command which allows saving the weight in the alibi memory and the transmission is lt II gt PID lt CRLF gt lt Il gt machine code only if functioning in 485 PID saving command of the weight data in the alibi memory CR ASCII 13 decimal code 41 3590EKR 3590EXP 3590EXT series indicator E AF08 02 12 01 EN U LF ASCII 10 decimal code If the gross weight is equal or greater than zero and stable the instrument will save the weight on the belt in the alibi memory And the PID string weight id will be transmitted on the PC port this is described in the following section 16 2 2 STRING FORMAT WEIGHT ID The PID string contains all the information regarding the executed weigh DESCRIPTION OF THE PID STRING lt ESC gt II PIDSS B LLLLLLELLLUUV Y YTTTTTTTTTTUU ID NO lt CR or CRLF gt in which Il 485 address only in the case of 485 transmission mode SS US instable weight ST stable weight OL weight out of range greater UL weight out of range lower comma character ASCII 044 B number of selected channel comma character ASCII 044 LLLLLLLLLL gross weight on 10 digits UU unit of measure comma character ASCII 044 YY 2 spaces in the case of null tare or semiautomatic tare PT in the case of preset tare TITTITTTTT tare weight on 10 digits comma character ASCII 044 ID XXXXX YYYYYY or NO weigh not stored in the alibi memory th
71. t shown on LED display is the sum weight of the active scales The tare in the axle weighing mode will be cleared only if the weighing of the vehicle is finished reset of the partial total 7 5 LOCKED UNLOCKED DISABLED TARE Normally when a tare value is inserted this value remains stored also after the printing and resetting of the partial total LOCKED TARE therefore it remains active also for the following weighs It is possible to choose that the tare value cancels itself automatically with each partial total printout UNLOCKED TARE By pressing at length the F5 key it is possible to quickly lock unlock the tare LED DISPLAY MEANING LoCK LOCKED TARE unLoCK UNLOCKED TARE Furthermore it is possible to carry out this setting or disable all the tare operations in the TARE LOCKED UNLOCKED SEtuP gt gt t LoCk parameter of the TECHNICAL SETUP TECH MAN REF 7 6 LIMITATION OF THE TARE FUNCTIONS For specific requirements it is possible to limit the functions of the tare with approved instrument by setting YES in the SEtuP gt gt d SALE step of the SET UP environment TECH MAN REF the SEMIAUTOMATIC TARE can not be modified with a manual or calculated tare or one from database the manual or calculated tare or one from database must be entered or modified only with UNLOADED scale With approved instrument the SEtuP gt gt d SALE step is not displayed Read only 23 3590EKR 3590EXP 3590EXT series indicator
72. tallation of the instrument we RECOMMEND disconnecting the battery if the instrument is not going to be used for more than 30 days Do not connect other equipment to the same socket as the one that the adapter is in Do not step on or crush the power supply cable 3 3 START UP TO TURN ON the instrument press the C key until the 6 status indicator LEDS turn on then release The LCD display shows Initially a welcome message settable in the TECHNICAL SET UP lt lt LoGo gt gt step TECH MAN REF while the instrument carries out a series of checking and preheating self tests E AFO08 XX name of the installed software in which XX identifies the software language XX YY is the software version installed EXECUTION AUTOZERO the instrument carries out the autozero at start up function on all active scales if a weight is detected within the percentile set in the lt lt Auto 0 gt gt step TECH MAN REF it is cleared if the weight is not within this tolerance with anon approved instrument the display shows the weight after a few instants with an approved instrument ZErO X is shown continuously on the LED display in wich X show the number of scale where zero function is done until the weight does not re enter within this tolerance The auto zero function at start up may be disabled in the set up environment only with non approved instrument see SEtuP gt gt ConFiG gt gt PArAM gt gt Auto 0 TECH MA
73. ting of the linked format are made Alternatively it s possible to automatically execute the function as described in section ENTRY OF AXLE NUMBER FOR AUTOMATIC PRINTING OF PARTIAL TOTAL GENERAL TOTAL Programmable printout By pressing the F9 key the resetting of the GENERAL TOTAL and the printing of the linked format are made GRAND TOTAL Programmable printout By pressing the F10 key the resetting of the GRAND TOTAL and the printing of the linked format are made START UP PRINTOUT Programmable printout When turning on the indicator the printout of this format is made this function can be used for example to unlock the pincers of the TM295 printer when this last is turned on the pincers are always locked CALCULATOR RESULT Programmable printout Once terminated the operation with the CALCULATOR function this format is printed See section CALCULATOR 33 3590EKR 3590EXP 3590EXT series indicator E AF08 02 12 01 EN U 14 1 LINKING OF THE FORMATS TO THE PRINT FUNCTIONS Through function 200 combinable with the desired key lt lt F KEYS gt gt step TECH MAN REF one accesses the linking of the print formats configurable in the SEtuP gt gt SEriAL gt gt Prn FMt step TECH MAN REF to the 13 programmable print functions Linked format Print function Print Functions Key Linked step PRINT KEY F5 S F 01 Function 405 combinable with the
74. to the printer serial port under way CN Inside the step these respectively indicate an unselected or selected parameter Active calculator function see section CALCULATOR 4 2 2 BATTERY LEVEL INDICATION The indicator is able to recognise whether it is powered by mains or by battery and indicate its charge level to enable the battery level indication one should configure the lt lt bt StAt gt gt step TECH MAN REF The charge level is shown during weighing by the battery symbol a charged battery partially charged battery discharged battery connect the indicator to the mains for recharging the battery if provided for by that model or replacing the battery 3590EKR 3590EXP 3590EXT series indicator E AF08_02_12 01_EN_U The indicator shows also when the battery is being recharged if provided for the model RECHARGE PHASE gt gt gt gt COMPLETED RECHARGE NOTES During the recharge the instrument can be normally used The instrument automatically turns off when the voltage goes below the minimum level 4 2 3 TILT DEVICE The TILT is a device which inhibits the indicator s weighing system and starts working when the instrument s inclination is greater than 2 for the pallet truck application or 5 for application on lift trucks The tilt message is shown on the display alternate to the weight value The activation of the tilt
75. type of indicator power supply red pilot light through built in power adapter green pilot light through battery charged battery _ pilot light off through battery discharged battery 6 Indicates that the weight detected by the weighing system is near zero including the interval of 1 4 1 4 of the scale s division Indicates that the weight is unstable NET Indicates that the weight shown by the LED display is a NET WEIGHT ST Indicates that a tare value has been acquired or entered g Indicates that the unit of measure in use is the gram kg Indicates that the unit of measure in use is the kilogram t Indicates that the unit of measure in use is the ton PCS Not used in the application F Not used in the application START Not used in the application STOP Not used in the application W1 W2 W3 See section MULTIRANGE AND MULTIDIVISION FUNCTION SP1 Not used in the application SP2 Not used in the application 3590EKR 3590EXP 3590EXT series indicator E AF08_02_12 01_EN_U SYMBOLS FUNCTIONS ON THE LCD DISPLAY SYMBOL FUNCTION 1 0 Indicates the type of active totalisation see section WEIGHING AND TOTALISATION PROCEDURES a The weight detected by the weighing system is near the zero included within the interval of 1 4 and 1 4 of the scale division Icon viewable only when the DIAGNOSTICS PERIPHERAL UNITS function is active see section DIAGNOSTIC PERIPHERALS
76. ves the blinking cursor to the left or to the right av Scrolls in one sense or the other the list of all the enterable characters 0 1 9 A B Y Z Examples To enter the letter B one should press the 2 key twice in the ChAr mode To enter the number 3 one should press the 3 key four times in the ChAr mode or press the F5 key one passes to the nuM mode and press the 3 key once 4 1 3 DISABLING THE KEYBOARD It is possible to disable all the keyboard functions except the C key for turning on and off in order to avoid undesired pressings of the scale keys To lock the keyboard press at length the F1 key the display shows the LoCK message for a few instants Now the keyboard is LOCKED if one presses a key the display shows for a few instants the PRESS AT LENGTH F1 FOR UNLOCKING message To unlock the keyboard press again at length the F1 key the display shows the unLoCk message for a few instants NOTE It s possible to lock all keys individually in a permanent way through the TECHNICAL SET UP TECH MAN REF 4 1 4 HELP MENU By pressing at length the HELP key it is possible to access a menu containing the list of keys with the relative function and status locked or unlocked indication The display shows in the upper part the key followed by the code of the linked function in the lt lt F KEYS gt gt step and a symbol indicating whether the key is unloc

USER MANUAL WEIGHT INDICATOR

Contents

Download Pdf Manuals

Related Search

Related Contents