QDSP-2090 Series User Manual
Contents
1. AN Danger of explosion when battery is replaced with incorrect type Only replace with the same or equivalent type recommended by the manufacturer Do not dispose of lithium batteries in domestic waste Dispose of the battery according to the local regulations dealing with the disposal of these special materials e g to the collecting points for disposal of batteries QDSP 2090 Series User s Manual Preface Preface m How to Use This Guide This guide is designed to be used as step by step instructions for installation and as a reference for operation troubleshooting and upgrades WR Unpacking When unpacking follow these steps 1 After opening the box save it and the packing material for possible future shipment 2 Remove all items from the box If any items listed on the purchase order are missing notify our customer service immediately 3 Inspect the product for damage If there is damage notify our customer service immediately Refer to Warranty Policy for the return procedure E Regulatory Compliance Statements This section provides the FCC compliance statement for Class A devices FCC Compliance Statement This equipment has been tested and found to comply with limits for a Class A digital device pursuant to Part 15 of the FCC rules These limits are designed to provide reason able protection against harmful interference in residential installations This equipment generates uses and can radiate radiof2. CSM Support Options Enabled Disabled Boot Option Filter Options UEFI and Legacy Legacy only UEFI only QDSP 2090 Series User s Manual Chapter 3 m Save amp Exit Menu Table 14 Save amp Exit Menu BIOS SETUP UTILITY Save Changes and Reset gt Select Screen Discard Changes and Reset TL Select Item Enter Select Save Options Change Opt Save Changes F1 General Help Discard Changes F2 Previous Values F3 Optimized Defaults Restore Defaults F4 Save amp Exit ESC Exit QDSP 2090 Series User s Manual Chapter 3 Save Changes and Exit Exit system setup after saving the changes Once you are finished making your selections choose this option from the Exit menu to ensure the values you selected are saved to the CMOS RAM The CMOS RAM is sustained by an onboard backup battery and stays on even when the PC is turned off When you select this option a confirmation window appears Select Yes to save changes and exit Discard Changes and Exit Exit system setup without saving any changes Select this option only if you do not want to save the changes that you made to the Setup program If you made changes to fields other than system date system time and password the BIOS asks for a confirmation before exiting Discard Changes Discards changes done so far to any of the setup values This option allows you to discard the selections you made and restore the previously saved values After selecting th
3. 7 Network cable with RJ45 connector WR Turning on the system 1 Connect the supplied AC power cord to the system AC power inlet on the I O panel of the system 2 Connect the other end of the AC power cord to a corresponding outlet 3 Press the power switch to turn on the system DC Jack Power Button Figure 8 Turning on the system QDSP 2090 Series User s Manual Chapter 2 E Connecting VESA Mount on QDSP 2090 Series d Take out the VESA mounting kit form your package and facing it onto the bottom of QDSP 2090 Series 3 R al Figure 9 VESA Mount Assembly 2 Then tightening the screws on your QDSP 2090 Series as figures shown below Following figures are the complete status when you done tm 5 100 Figure 10 VESA Mount on QDSP 2090 Series QDSP 2090 Series User s Manual Chapter 2 E Mounting your PC to a monitor 1 Firstly mount your VESA kit on the backside of the monitor with four screws in the package 2 Secondly place the QDSP 2090 Series on the VESA mounting kit and then tightening the screws from the holes on both sides of the VESA bracket make sure the computer is fitting well on the bracket Figure 11 VESA mounting NOTE To fasten the metal shelf your monitor must comply with VESA75 or S VESA100 standard Remarks VESA mounting kit could be used as wall mounting kit as well QDSP 2090 Series User s Manual Chapter 3 Chapter 3 AMI BIOS Setup E Ov
4. QDSP 2090 Series Digital Signage Player with Intel Haswell Processor User s Guide Content Content MM E 2 ee E 3 RASS enna EEE 4 Safety VS ele tee cesta eaea eaen aaan KEE maa career vencnieawecntceexemmees 5 EL Betore VOU EUR 5 Lo When Working Inside Rule 6 O Preventing Electrostatic Leet eeeuecueeun eege eegene doen 6 L Instructions for Lithium Battery ccccccccccccccccccceeceeceeeeeeceeeeeeeeeeeeeeeeeeeess 7 EE 8 TI How to Use This Guide cece ccccccceeceseeecesueeseeeeeeeeeeeseueueeeueeeeueeeeeaeeeees 8 EL Unpacking Seege etetegcegegegeg eegent 8 Regulatory Compliance Statement een 8 O Maintaining de TE ul 10 Chapter T JOEREN 12 O Overview EEN 12 SNE Gelee e e 13 C System KT 15 EH Mechanical Wetter cccinicatanueiriaicuse rpiuca nseicapsiea tuidneuebeed nicandnsins 18 Chapter 2 Getting Giarted unn 19 SW THT UN your E 19 CI Connecting VESA Mount on QDSP 2090 Gees 23 EL Mounting your PC to MORMON cases eege 24 Chapter 3 AMI BIOS Eesen er neem terre eee ea 25 CD SRI EE 25 KEN Main le ee eege dee ee Eege 26 Q Advanced MOU siducicsinsinsnssunsnudarseseassdulegaedepanswneadiindendamuiedaanaiuadiovenaudacusbanensatiad 27 KT Power Menu ats thcc dare cette deste ete eeeg 34 HU Sec rity EE 35 O 0s e 217 W EE 36 O Save amp Exit TE ia sais cee tienctiaaiadionaiaredsaailienadianaiisaindeatiaiedeatiuaiadanaiocsdaaacouatosaiannsaiad 37 Chapter 4 Driver InstallatiOn EE 39 QDSP 2090 Series User s Man
5. ained in this user s guide Follow installation and troubleshooting instructions closely Preventing Electrostatic Discharge Static electricity can harm system boards Perform service at an ESD workstation and follow proper ESD procedure to reduce the risk of damage to components We strongly encourages you to follow proper ESD procedure which can include wrist straps and smocks when servicing equipment You can also take the following steps to prevent damage from electrostatic discharge ESD QDSP 2090 Series User s Manual Safety Instructions m When unpacking a static sensitive component from its shipping carton do not remove the component s antistatic packing material until you are ready to install the component in a computer Just before unwrapping the antistatic packaging be sure you are at an ESD workstation or grounded This will discharge any static electricity that may have built up in your body m When transporting a sensitive component first place it in an antistatic container or packaging H Handle all sensitive components at an ESD workstation If possible use antistatic floor pads and workbench pads H Handle components and boards with care Don t touch the components or contacts on a board Hold a board by its edges or by its metal mounting bracket H Do not handle or store system boards near strong electrostatic electromagnetic magnetic or radioactive fields E Instructions for Lithium Battery WARNING
6. creens Table 2 BIOS Main Menu BIOS SETUP UTILITY Main Advanced Power Security Boot Save amp Exit Product Information Product Name QDSP 2090 BIOS Version R1 00 x64 BIOS Build Date 06 02 2015 ME FW Version 9 1 25 1005 CPU Information Intel Core i3 4340TE CPU 2 60GHz Microcode Revision 1d gt Select Screen Processor Cores 2 TL Select Item Enter Select Change Opt F1 General Help F2 Previous Values Memory Information Total Size 2048 MB DDR3 F3 Optimized Defaults Frequency 1600 MHz F4 Save amp Exit System time 19 36 12 Access Level Administrator Version 2 17 1249 Copyright C 2015 American Megatrends Inc QDSP 2090 Series User s Manual Chapter 3 E Advanced Menu Table 3 Advanced Menu BIOS SETUP UTILITY I avan 2Ccurl Onboard LAN1 Controller Enabled Onboard LAN1 Boot Disabled Onboard LAN2 Controller Enabled Onboard LAN2 Boot Disabled Audio Controller Enabled gt Select Screen TL Select Item Enter Select Change Opt F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save amp Exit ESC Exit gt Display Configuration gt Super IO Configuration gt CPU Chipset Configuration gt SATA Configuration gt USB Configuration gt H W Monitor Onboard LAN 1 Controller Options Disabled Enabled Onboard LAN 1 Boot Options Disabled Enabled Onboard LAN 2 Controller Options Disab
7. ed QDSP 2090 Series User s Manual Chapter 3 Table 8 Advanced Menu SATA Configuration BIOS SETUP UTILITY SATA Configuration gt Select Screen TL Select Item SATA Controller s Enabled Enter Select SATA Mode Selection AHCI Change Opt SATA Controller Speed Default F1 General Help f F2 Previous Values Serial ATA Port 1 Empty F3 Optimized Defaults Port 1 Enabled F4 Save amp Exit MSATA Port 1 Empty FPE Port 1 Enabled mSATA Port 2 Empty Port 2 Enabled SATA Controller s Options Enabled Disabled SATA Mode Selection Options IDE AHCI SATA Controller Speed Options Default Gen 1 Gen 2 Gen 3 Port Options Disabled Enabled QDSP 2090 Series User s Manual Chapter 3 Table 9 Advanced Menu USB Configuration USB Configuration USB Devices 2 Hubs Legacy USB Support XHCI Legacy Support XHCI hand off EHCI Hand off USB Mass Storage Driver Support Enabled Enabled Enabled Disabled Enabled gt Select Screen TL Select Item Enter Select Change Opt F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save amp Exit ESC Exit Legacy USB Support Options Enabled Disabled Auto XHCI Legacy Support Options Enabled Disabled XHCI hand off Options Enabled Disabled EHCI hand off Options Disabled Enabled USB Mass Storage Driver Support Options Disabled Enabled QDSP 2090 Series User s Manua
8. erview This chapter provides a description of the AMI BIOS The BIOS setup menus and available selections may vary from those of your product For specific information on the BIOS for your product please contact with your dealer NOTE The BIOS menus and selections for your product may vary from those in this chapter For the BIOS manual specific to your product please contact with us AMI s ROM BIOS provides a built in Setup program which allows the user to modify the basic system configuration and hardware parameters The modified data will be stored in a battery backed CMOS so that data will be retained even when the power is turned off In general the information saved in the CMOS RAM will not need to be changed unless there is a configuration change in the system such as a hard drive replacement or when a device is added It is possible for the CMOS battery to fail which will cause data loss in the CMOS only If this happens you will need to reconfigure your BIOS settings QDSP 2090 Series User s Manual Chapter 3 E Main Menu The BIOS Setup is accessed by pressing the DEL key after the Power On Self Test POST memory test begins and before the operating system boot begins Once you enter the BIOS Setup Utility the Main Menu will appear on the screen The Main Menu provides System Overview information and allows you to set the System Time and Date Use the lt and gt cursor keys to navigate between menu s
9. ety Instructions Safety Instructions E Before You Begin Before handling the product read the instructions and safety guidelines on the following pages to prevent damage to the product and to ensure your own personal safety Refer to the Advisories section in the Preface for advisory conventions used in this user s guide including the distinction between Warnings Cautions Important Notes and Notes m Always use caution when handling operating a computer Only qualified experienced authorized electronics service personnel should access the interior of a computer The power supplies produce high voltages and energy hazards which can cause bodily harm m Use extreme caution when installing or removing components Refer to the installation instructions in this user s guide for precautions and procedures If you have any questions please contact our Post Sales Technical Support m Access can only be gained by service persons or by users who have been instructed about the reasons for the restrictions applied to the location and about any precautions that shall be taken and access is through the use of a tool or lock and key or other means of security and is controlled by authority responsible for the location WARNING High voltages are present inside the chassis when the unit s power cord is plugged into an electrical outlet Turn off system power turn off the power A supply and then disconnect the power cord from its sou
10. for safe operation is not compromised Consideration should be given to the maximum rated ambient temperature Overheating can cause a variety of problems including premature aging and failure of chips or mechanical failure of devices If the system has been exposed to abnormally cold temperatures allow a two hour warm up period to bring it up to normal operating temperature before turning it on Failure to do so may cause damage to internal components particularly the hard disk drive H Humidity High humidity can cause moisture to enter and accumulate in the system This moisture can cause corrosion of internal components and degrade such properties as electrical resistance and thermal conductivity Extreme moisture buildup inside the system can result in electrical shorts which can cause serious damage to the system Buildings in which climate is controlled usually maintain an acceptable level of humidity for system equipment However if a system is located in an unusually humid location a dehumidifier can be used to maintain the humidity within an acceptable range Refer to the Specifications section of this user s guide for the operating and storage humidity specifications Altitude Operating a system at a high altitude low pressure can cause electrical problems related to arcing and corona effects This condition can also cause sealed components with internal pressure such as electrolytic capacitors to fail or perform at red
11. imized Defaults F4 Save amp Exit ESC Exit Serial Port Options Disabled Enabled Change Settings Options Auto lIO 3F 8h IRQ 4 lO 3F 8h IRQ 3 4 5 6 7 9 10 11 12 lO 2F 8h IRQ 3 4 5 6 7 9 10 11 12 lO 3E8h IRQ 3 4 5 6 7 9 10 11 12 IO 2E8h IRQ 3 4 5 6 7 9 10 11 12 Serial Port Type Options RS232 RS422 RS485 QDSP 2090 Series User s Manual Chapter 3 Table 7 Advanced Menu CPU Chipset Configuration BIOS SETUP UTILITY Main Advanced Power Security Boot Save amp Exit CPU Chipset Configuration EIST Enabled gt Select Screen TL Select Item Turbo Mode Enabled Enter Select Hyper threading Enabled Change Opt VT d Enabled F1 General Help F2 Previous Values F3 Optimized Defaults Active Processor Cores All F4 Save amp Exit ESC Exit Limit CPUID Maximum Disabled Execute Disable Bit Enabled Intel Virtualization Technology Disabled Intel TXT LT Support Disabled Version 2 17 1249 Copyright C 2015 American Megatrends Inc EIST Options Disabled Enabled Turbo Mode Options Disabled Enabled Hyper threading Options Disabled Enabled VT d Options Disabled Enabled Active Processor Cores Options All 1 2 3 Limit CPUID Maximum Options Disabled Enabled Execute Disable Bit Options Disabled Enabled Intel Virtualization Technology Options Disabled Enabled Intel TXT LT Support Options Disabled Enabl
12. is option a confirmation appears Select Yes to discard any changes and load the previously saved values Load Optimal Defaults Load Optimal Default values for all the setup values This option allows you to load optimal default values for each of the parameters on the Setup menus which will provide the best performance settings for your system The F9 key can be used for this operation Load Failsafe Defaults Load Optimal Default values for all the setup values This option allows you to load failsafe default values for each of the parameters on the Setup menus which will provide the most stable performance settings The F8 key can be used for this operation QDSP 2090 Series User s Manual Chapter 4 Chapter 4 Driver Installation If your QDSP 2090 Series does not come with an operating system pre installed you will need to install an operating system and the necessary drivers to operate it After you have finished assembling your system and connected the appropriate power source power it up using the power supply and install the desired operating system For other operating systems please contact us QDSP 2090 Series User s Manual
13. k Dimension 200 x 35 x 153 1 mm W x H x D Figure 3 Mechanical Dimensions QDSP 2090 Series User s Manual Chapter 2 Chapter 2 Getting Started E Setting up your PC Connect the monitor mouse and keyboard Connecting the monitor Connect the DVI I DP cable from your display to the DVI I DP port DVI I DP Figure 4 Connect the DVI I DP cable QDSP 2090 Series User s Manual Chapter 2 Connecting USB mouse amp keyboard Your QDSP 2090 Series does not come with a keyboard and mouse but you can use any USB keyboard or mouse with your computer 2x USB3 0 4x USB3 0 Figure 5 Connecting USB mouse amp keyboard Upper QDSP 2090 Lower QDSP 2091 NOTE Using a third party USB mouse or keyboard may require software drivers Check the manufacturer s website for the latest software drivers QDSP 2090 Series User s Manual Chapter 2 COM port COM port with the pin definitions COM Half Duplex Full Duplex Pin RS 232 RS 422 RS 485 RS 485 1 DCD TX DATA TX 2 RXD TX DATA TX 3 TXD RX NA RX 4 DTR RX NA RX 5 GND GND GND GND 6 DSR NA NA NA 7 RTS NA NA NA 8 CTS NA NA NA 9 RI NA NA NA Figure 6 COM port QDSP 2090 Series User s Manual Chapter 2 WH Connecting to a network device Connect one end of a network cable to the LAN port on the system rear panel and the other end to a hub or switch 2x LAN Figure
14. l Chapter 3 Table 10 Advanced Menu H W Monitor PC Health Status gt Select Screen CPU Warming Temperature Disabled TL Select Item CPU Temperature 464 C Enter Select System Temperature eer Change Opt CPU Fan Speed 4753 RPM F1 General Help F2 Previous Values VCORE 241 757 V F3 Optimized Defaults VIN 12 060 V F4 Save amp Exit 5V 5 066 V ESC Exit VMEN 1 541 V CPU Warning Temperature Options Disabled 80 C 85 C 90 C 95 C QDSP 2090 Series User s Manual Chapter 3 E Power Menu Table 11 Power Menu BIOS SETUP UTILITY Main Advanced Power Security Boot Save amp Exit Power Configuration ACPI Sleep State S3 Suspend to RAM Restore AC Power Loss Power Off Power Saving Mode Disabled gt Select Screen Resume Event Control TL Select Item Resume By LAN Device Disabled Enter Select Resume By PCI E Device Disabled 5 PA e Resume By Ring Device Disabled ee ee F2 Previous Val Resume By RTC Alarm Disabled F3 eer Bere gt WatchDog Timer Configuration F4 Save amp Exit ESC Exit Version 2 17 1249 Copyright C 2015 American Megatrends Inc ACPI Sleep State Options Suspend Disabled S3 Suspend to RAM Restore AC Power Loss Options Power Off Power On Last State Power Saving Mode Options Disabled EUP Enabled DeepSx Enabled Resume By LAN Device Options Enabled Disabled Resume By PCI E Device Options Disabled Enabled Re
15. led Enabled Onboard LAN 2 Boot Options Disabled Enabled Audio Controller Options Disabled Enabled QDSP 2090 Series User s Manual Chapter 3 Table 4 Advanced Menu Display Configuration BIOS SETUP UTILITY Display Configuration gt Select Screen TL Select Item Primary Display Auto Enter Select UMA Frame Buffer Size 256 MB Change Opt DVMT Pre Allocated 64M F1 General Help DVMT Total Gfx Mem 256 M F2 Previous Values F3 Optimized Defaults F4 Save amp Exit ESC Exit Primary IGFX Boot Display VBIOS Default Primary Display Options Auto IGFX PEG PCIE UMA Frame Buffer Size Options 128MB 256MB 512MB DVMT Pre Allocated Options 32M 64M 96M 128M 160M 192M 224M 256M 288M 320M 352M 384M 416M 448M 480M 512M DVMT Total Gfx Mem Options 128M 256M MAX Primary IGFX Boot Display Options VBIOS Default CRT DVI DP1 DP2 QDSP 2090 Series User s Manual Chapter 3 Table 5 Advanced Menu Super IO Configuration BIOS SETUP UTILITY Super IO Chip Parameters gt Serial Port 1 Configuration Table 6 Advanced Menu Super IO Configuration Serial Port 1 Configuration BIOS SETUP UTILITY Serial Port 1 Configuration gt Select Screen t Select Item Serial Port Enabled Enter Select Change Opt Device Settings 10 3F8h IRQ 4 F1 General Help Change Settings Auto F2 Previous Values Serial Port 1 Type RS232 F3 Opt
16. ng Kit Optional WiFi or 3G module Features Intel Haswell Processor with H81 Q87 Express chipset 2 x DDR3 SO DIMM up to 16 GB 2x DP 1x DVI I 2x GbE and 5 1 channel audio output 1x SATA HDD or SSD 6x USB3 0 2x USB3 0 4x USB2 0 Intel iAMT 9 0 amp TPM supported QDSP 2091 Optional Wireless Ethernet or 3G Module QDSP 2090 Series User s Manual Chapter 1 E Product Specifications Construction Metal Housing System Board 4th Generation Intel Haswell Core i3 i5 i7 Processor Intel H81 Express Chipset QDSP 2090 Intel Q87 Express Chipset QDSP 2091 Memory 2x DDR3 SO DIMM up to 16GB UO Panel Front I O 3x 3 5mm Phone Jack support 5 1 channel audio output 1x S PDIF Output 6x USB 3 0 QDSP 2091 2x USB 3 0 4x USB2 0 QDSP 2090 1x Power Button With Power LED 1x Storage status LED HDD 1x Wifi status LED 1x 3G external antenna 1x Reset Switch Rear I O 1x DC JACK 1x DVI I for DVI D or VGA output 2x DP 2x RJ 45 GbE ports 1x COM Port support RS 232 422 485 2x Wifi external antennas BIOS AMI uEFI BIOS 1x128Mb SPI flash ROM onboard Storage 1x 2 5 SATA HDD or SSD 2x MSATA mixed with mPCle QDSP 2091 Expansion 2 x mPCle slot Optional for 3G WiFi Bluetooth module QDSP 2090 2 x mPCle mSATA slot Optional for 3G WiFi Bluetooth module QDSP 2091 1x SIM card slot for 3G appliance support user accessible Power Supply Input 100 240 VAC Outp
17. rce before removing the chassis cover Turning off the system power switch does not remove power to components QDSP 2090 Series User s Manual Safety Instructions When Working Inside a Computer Before taking covers off a computer perform the following steps d 2 Turn off the computer and any peripherals Disconnect the computer and peripherals from their power sources or subsystems to prevent electric shock or system board damage This does not apply when hot swapping parts Follow the guidelines provided in Preventing Electrostatic Discharge on the following page Disconnect any telephone or telecommunications lines from the computer In addition take note of these safety guidelines when appropriate A To help avoid possible damage to system boards wait five seconds after turning off the computer before removing a component removing a system board or disconnecting a peripheral device from the computer When you disconnect a cable pull on its connector or on its strain relief loop not on the cable itself Some cables have a connector with locking tabs If you are disconnecting this type of cable press in on the locking tabs before disconnecting the cable As you pull connectors apart keep them evenly aligned to avoid bending any connector pins Also before connecting a cable make sure both connectors are correctly oriented and aligned CAUTION Do not attempt to service the system yourself except as expl
18. requency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause interference to radio or television equipment reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures H Reorient or relocate the receiving antenna m Increase the separation between the equipment and receiver H Connect the equipment to an outlet on a circuit different from that to which the QDSP 2090 Series User s Manual Preface receiver is connected Consult the dealer or an experienced radio TV technician for help Changes or modifications not expressly approved by your dealer could void the user s authority to operate the equipment NOTE The assembler of a personal computer system may be required to test the system and or make necessary modifications if a system is found to S cause harmful interference or to be noncompliant with the appropriate standards for its intended use QDSP 2090 Series User s Manual Preface E Maintaining Your Computer Environmental Factors H Temperature The ambient temperature within an enclosure may be greater than room ambient temperature Installation in an enclosure should be such that the amount of air flow required
19. ripheral acting as additional plug in sites or hubs S PDIF S PDIF output for carrying digital audio signals out to the device Phone Jack Line Out The stereo headphone jack is used to connect the system s audio out signal to amplified speakers or headphones MIC IN The microphone jack is designed to connect the microphone used for video conferencing voice narrations or simple audio recordings Line IN The Line in jack is designed to take input from a higher powered sound Source 3G External Antenna Spared hole on the casing for connecting 3G external antenna QDSP 2090 Series User s Manual Chapter 1 E Rear Rear WiFi Antennas COM DVI I RJ 45 DP DC Jack Figure 2 Rear IO COM D Sub 9 pin connector for RS 232 422 485 connection Ethernet The eight pin RJ 45 LAN port supports a standard Ethernet cable for connection to a local network DP DP is a display interface used to connect a video source to a display device such as a computer monitor or a television set DVI I DVI I connector for DVI D or VGA output DC Jack The supplied power adapter converts AC power to DC for use with this jack Power supplied through this jack supplies power to the PC To prevent damage to the PC always use the supplied power adapter WiFi External Antenna Spared hole on the casing for connecting WiFi external antenna QDSP 2090 Series User s Manual Chapter 1 E Mechanical Dimensions u e
20. sume By Ring Device Options Disabled Enabled Resume By RTC Alarm Options Disabled Enabled Watchdog Timer Configuration WDT Function Options Disabled Enabled QDSP 2090 Series User s Manual Chapter 3 WR Security Menu Table 12 Security Menu BIOS SETUP UTILITY Password Description gt Select Screen TL Select Item Enter Select Change Opt F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save amp Exit ESC Exit If ONLY the Administrator e password is set then this only limits access to Setup and is only asked for when entering Setup If ONLY the User s password is set then this is a power on password and must be entered to boot or enter Setup In Setup the User will have Administrator rights The password length must be in the following range Minimum Length 3 Maximum length 20 Administrator Password User Password QDSP 2090 Series User s Manual Chapter 3 E Boot Menu Table 13 Boot Menu BIOS SETUP UTILITY gt Select Screen Boot Configuration TL Select Item Full Screen LOGO Display Disabled Enter Select Change Opt Setup Prompt Timeout 1 F1 General Help Bootup NumLock State On F2 Previous Values F3 Optimized Defaults CSM Support Enabled F4 Save amp Exit Boot Option Filter Legacy only ESC Exit Boot Option Priorities Full Screen LOGO Display Options Disabled Enabled Bootup Numlock State Options On Off
21. t the battery can provide power to the system for a limited amount of time depending on the UPS system UPS systems range in price from a few hundred dollars to several thousand dollars with the more expensive unit s allowing you to run larger systems for a longer period of time when AC power is lost UPS systems that provide only 5 minutes of battery power let you conduct an orderly shutdown of the system but are not intended to provide continued operation Surge protectors should be used with all UPS systems and the UPS system should be Underwriters Laboratories UL safety approved QDSP 2090 Series User s Manual Chapter 1 Chapter 1 Introduction E Overview The QDSP 2090 Series is a compact size Box PC ideal for space critical applications This embedded hardware platform features 4th Generation Intel Core i3 i5 i7 Processors Intel H81 Express Chipset QDSP 2090 Intel Q87 Express Chipset QDSP 2091 and DDR3 SO DIMM It comes with a 2 5 SATA hard drive or SSD 2x DP 1x DVI I 2x RJ 45 6x USB3 0 QDSP 2091 2x USB3 0 4x USB2 0 QDSP 2090 1x COM and HD Audio The QDSP 2090 provides high reliability for harsh environments compact size high performance and is highly suited to a wide range of industrial applications such as Digital Signage Gaming Transportation Surveillance and Thin Servers Checklist QDSP 2090 QDSP 2091 Power Adapter Power Cord Driver CD Quick installation Guide VESA Mounti
22. ual Figures Figures Figure 1 Front IO Upper QDSP 2090 Lower ODGP 20011 15 Fig r 2 E panama ae ene eee ee mee ee A ER eee ae eee ree ee 17 Figure 3 Mechanical Re 18 Figure 4 Connect the DVL I DPcable e 19 Figure 5 Connecting USB mouse amp keyboard Upper QDSP 2090 Lower EE ee 20 gle Sigg om G1 E 21 Figure 7 Network cable with RJ45 connechor un 22 Figure 8 Turning ON the system en 22 Figure 9 VESA Mount eeneg esdeeki dese 23 Figure 10 VESA Mount on QDSP 2090 Series n 23 Figure 11 eelere E 24 QDSP 2090 Series User s Manual Tables Tables Table 1 QDSP 2090 Series Gpoechficatton EE 14 Table 2 BIOS Main Menu icesiccannscnnsaxnsasnsannsarasanesannsannsalionsazmearmocmocnecmertmedcn 26 Table 3 Advanced MenUs sirir serisini anaiai 27 Table 4 Advanced Menu Display Contouraton 28 Table 5 Advanced Menu Super IO Configuration eeeceeeeeeeeeeeees 29 Table 6 Advanced Menu Super IO Configuration Serial Port 1 ei Oe EI e EE 29 Table 7 Advanced Menu CPU Chipset Configuration cceeeee 30 Table 8 Advanced Menu SATA Configuration ccccceeeeceeeeeteeeeeeeees 31 Table 9 Advanced Menu USB Configuration EE 32 Table 10 Advanced Menu HAN Monitor enn 33 Table 11 Power Menu 34 Table 12 Security Menu ener cceexen ese Genepecxvnncxeusvenseeusrenerenexveeeuexaeneteee 35 Table Wed EE 36 Table 14 Save amp Exit egene 37 QDSP 2090 Series User s Manual Saf
23. uced efficiency QDSP 2090 Series User s Manual Preface Power Protection The greatest threats to a system s supply of power are power loss power spikes and power surges caused by electrical storms which interrupt system operation and or damage system components To protect your system always properly ground power cables and one of the following devices H Surge Protector Surge protectors are available in a variety of types and usually provide a level of protection proportional with the cost of the device Surge protectors prevent voltage spikes from entering a system through the AC power cord Surge protectors however do not offer protection against brownouts which occur when the voltage drops more than 20 percent below the normal AC line voltage level H Line Conditioner Line conditioners go beyond the over voltage protection of surge protectors Line conditioners keep a system s AC power source voltage at a fairly constant level and therefore can handle brownouts Because of this added protection line conditioners cost more than surge protectors However line conditioners cannot protect against a complete loss of power H Uninterruptible Power Supply Uninterruptible power supply UPS systems offer the most complete protection against variations on power because they use battery power to keep the server running when AC power is lost The battery is charged by the AC power while it is available so when AC power is los
24. ut 19V DC QDSP 2090 Series User s Manual Chapter 1 Cooling System Fan with smart fan function OS Support Windows 7 Windows 8 Linux Temperature Operating 0 C 50 C 32 F 122 F 0 90 non condensing Humidity Storage 20 C 80 C 4 F 176 F 0 90 non condensing Dimensions 200 x 153 1 x 35 mm 7 87 x 6 03 x 1 38 W x D x H Weight 1 Kg 2 20 Ib Mounting VESA Mount Certifications CE FCC Class A Table 1 QDSP 2090 Series Specification QDSP 2090 Series User s Manual Chapter 1 E System tour Refer to the figures below to identify the components of the system E Front IO 3G Antenna Figure 1 Front IO Upper QDSP 2090 Lower QDSP 2091 Power Button with Power LED Blue The power push button allows powering ON and OFF the system The power LED will light when the PC is power on Reset Switch To clear the CMOS use the tip of a pen to press the button briefly for less than three seconds HDD LED Red The hard disk LED blinks when data is being written into or read from the HDD WiFi LED Green When the data is Transferring the WiFi LED will blink USB The USB Universal Serial Bus port is compatible with USB devices such as keyboards mouse devices cameras and hard disk drives USB allows many QDSP 2090 Series User s Manual Chapter 1 devices to run simultaneously on a single computer with some pe
Download Pdf Manuals
Related Search