Office Pro 1000-1400VA Manual
Contents
1. ORIGIN A Power Systems 192321942005001 Office Pro UPS1000VA 1500VA Users Manual SAVE THESE INSTRUCTIONS This manual contains important instructions that should be followed during installation and maintenance of the UPS and batteries CAUTION Intended for installation in a controlled environment Maximum ambient temperature 95 F Servicing of batteries should be performed or supervised by personnel knowledgeable of batteries and the personnel away from battery required precautions Keep unauthorized To reduce the risk of fire connect only to a circuit provided with 20 amperes maximum branch circuit overcurrent protection in accordance with the National Electric Code ANSI NFPA 1 Inspection Inspect the UPS upon receipt Notify the carrier and dealer if there is damage The package is recyclable save it for reuse or dispose of it properly 2 Placement 3 Check the Site Wiring Fault Indicator Caution If the site wiring fault indicator lights get a qualified electrician to correct the building wiring 4 Connect the loads First connect the UPS to the AC input power source Next plug your computer monitor or other devices into the receptacles on the rear of the UPS To use the UPS as a master On Off switch make sure that all of the connected devices are switched On Caution To prevent an overloading condition do not con2. 5 4 RJ11 RJ45 connector to 00 00 5 Site Wiring Fault Indicator LSKVA 15A 250V 2 6 USB Interface Not supplied if the RS232 interface is built DaD G2 7 Input fuse gt 1 we L J Note Once the battery is disconnected the loads are not protected from power outages 1 Use a phillips head screwdriver to remove the two top cover screws and slide back the cover Please refer to the figures STEP 1 through STEP 4 Gently pull the batteries out of the UPS Loosen the black wire from the negative terminal and red wire from the positive terminal Connect the battery leads to the new batteries Note Small sparks at the battery connectors are normal during connection Slide the batteries into the UPS Close the front panel and fasten two screws Dispose of the old batteries properly at an appropriate recycling facility O ND OT wh If your UPS malfunctions during operation please check the table below Please consult Orion Power Systems Online Technical Support or call Orion Power Systems for assistance with problems that cannot be resolved using the troubleshooting guide Situation Check Items Solution Utility power is normal but the Line LED is not on 1 Is the power switch on 2 Is the fuse 1 Press Power On button on front of unit 2 Replace fuse good 3 Is the power cord loose with same rating 3 Re connect the power cord pro
3. nect a laser printer to the backup outlets These UPS outlets provide battery power to the connected equipment when utility voltage is outside acceptable limits 5 RJ11 RJ45 Connector Optional Provide an RJ11 RJ45 connector to extend the connection of telecommunication network cable 6 Connect Computer Interface Port Optional Connect the optional interface cable to the USB interface port on the back of the UPS Connect to the computer See software documentation for installation instruction Qe o e o 7 Operation Test 1 Connect the UPS to the wall receptacle 2 Press the Power button on the front panel verify that the Green Line 7 LED is on 3 Connect your computer equipment to the receptacles on the back of the UPS Unplug the input power cable of the UPS from the wall receptacle to check if the Line and Inverter 7 LED are flashing every 2 seconds Verify that the audible alarm is beeping 4 The ups is now running on internal battery to support the connected equipment 5 Reconnect the ups to the wall receptacle to complete the test The audible alarm will silence and the Green Line LED will be visible 6 IMPORTANT Plug the UPS into the wall outlet to charge the internal battery for a minimum of 8 hours prior to using the UPS 7 STORAGE Store at 15 to 30 C 5 to 86 F charge the UPS battery ever
4. perly Inverter LED flashes every 2 seconds but no output Battery voltage is too low Recharge the UPS for 24 hours Audible alarm beeps continuously when Utility power Check for overload condition Reduce connected load by removing one or more devices is normal Alarm buzzer beeps for 10 seconds followed by UPS Reduce connected load by removing one or more devices shutdown No LEDs display on the front panel Contact Orion Power Systems Technical Support UPS does not provide expected back up time 1 The UPS battery is weak due to recent 1 Charge the battery 2 If the battery is near the end of its outage 2 The UPS battery is near the end service life replace the battery of its service life The UPS operates normally but the site wiring fault Building wiring error such as missing ground Have a qualified electrician correct the building wiring indicator is lit or hot to neutral wire reversal UPS switch is on but UPS does not operate Is the incoming Utility power normal If Utility power is normal connect ups to wall receptacle first then switch on UPS Orion Power Systems Inc Toll Free 877 385 1654 8640 Philips Hwy www orionpowersystems com Jacksonville FL 32256
5. y six months Store at 30 to 45 C 86 to 113 F charge the UPS battery every three months Orion Power Systems Inc 8640 Philips Hwy Toll Free 877 385 1654 www orionpowersystems com Jacksonville FL 32256 1 Line LED Green LED remains lit when incoming utility power is normal Green LED flashes every 2 seconds when the UPS is in battery charging mode Green LED remains lit and audible alarm beeps continuously when the UPS is in overload condition 2 Inverter LED Yellow LED flashes every 2 seconds and audible alarm beeps continuously during a power failure 3 Overload LED Ak Red LED remains lit and audible alarm beeps continuously when the UPS is in overload condition 4 Check Battery LED Red LED flashes every 0 5 seconds and audible alarm beeps every 0 5 seconds when UPS is in battery low condition 5 Main Switch a To power on off the UPS when incoming Utility power is normal b To enable DC Start Function when Utility fails To enable DC Start properly you are recommended to connect lt 80 output load with the UPS only When using the DC Start ensure the equipment connected to the UPS is switched on It is not recommended to add other equipment after the DC Start function is activated 1 AC Inlet 3 6 2 Backup Outlets 69cs NEMA5 15R Fuse 5 leo eee E o 3 True RS232 interface port Optional IKVA 12A 250V 4
Download Pdf Manuals
Related Search