MPEG-4 DVR QUICK
Contents
1. 2 1 Front Panel 1 LED Indication The following LEDs will be on when Q When power is connected HDD HDD is reading or recording HDD Full HDD is full Once the alarm or motion is triggered When timer recording is activated Note If you want to turn off your DVR please disconnect the power supply 2 USB port To quickly backup or upgrade firmware OSD you can insert a compatible USB flash drive into this USB port Before using the USB flash drive please use your PC to format the USB flash drive first Note For the list of compatible USB flash drives please refer to APPENDIX 2 PIN CONFIGURATION in the user manual 3 IR receiving zone If you removed the control panel from the DVR to use as a remote controller use the remote controller to aim at this area to control the DVR operation Unlock mode To lock the control panel on the DVR please switch the lock button to the left gt lock mode If you want to remove the control panel from the DVR to use as a remote controller please switch the lock button to the right U unlock mode Note Due to panel position difference please place the vertical panel sticker on the removed controller for operation convenience 5 Menu Press this button to enter exit the quick start menu Under the sub layer of the advanced setting menu use this button to confirm the2. external alarm on the screen Note The audio source connected to the Audio 1 will be recorded with the video of the CH13 The audio source connected to the Audio 2 will be recorded with the video of the CH14 The audio source connected to the Audio 3 will be recorded with the video of the CH15 The audio source connected to the Audio 4 will be recorded with the video of the CH16 4 2 Playback Press LATEST button on the DVR control panel and the device will playback the latest recorded video Note There must be at least 8192 images of recorded data for playback to work properly If not the device will stop playback For example if the IPS is set to 30 the recording time should be at least 273 seconds 8192 images 30 IPS for the playback to work properly Playback related operations are described below 1 Fast Forward gt gt Fast Rewind 44 You can increase the speed for fast forward and rewind on this device In the playback mode Press gt gt once to get 4X speed forward and press twice to get 8X speed etc And the maximum speed is 32X Press lt lt once to get 4X speed rewind and press twice to get 8X speed etc And the maximum speed is 32X 2 Pause i Image Jog Press IF button to pause the playback In the Pause mode Press gt gt button once to get one frame forward Press lt lt button once to get one fra
3. AKPD616 MPEG 4 DVR QUICK The control panel can be removed E KPD616 16 Channel MPEG 4 Network DVR ROHS AND WEEE All lead free products offered by the company comply with the requirements of the European law on the Restriction of Hazardous Substances ROHS directive which means our manufacture processes and products are strictly lead free and without the hazardous substances cited in the directive The crossed out wheeled bin mark symbolizes that within the European Union the product must be collected separately at the product end of life This applies to your product and any peripherals marked with this symbol Do not dispose of these products as unsorted municipal waste Please read this instruction thoroughly before operation and retain it for future reference The image shown above may differ from the actual product appearance KPD616 Quick _V0 81 1 1 Product Description This MPEG 4 multiplex network DVR series combined remote surveillance burglar prevention and evidentiary recording features and is designed to become a simple entry level system with all necessary functions 1 2 Package Contents _ Digital Video Recorder DVR _ Free licensed software AP disc _ Adapter and power cord _ DSUB PIN connector _ Manual amp quick start Screws 4 2 FRONT AND REAR PANELS
4. TIMER DATE D DATE FORMAT DAYLIGHT SAVING CAMERA DETECTION ALERT NETWORK DISPLAY SERIAL TYPE BAUD RATE HOST ID PASSWORD RESET DEFAULT SYSTEM CONFIG CLEAR HDD UPGRADE ADVANCE CONFIG ADVANCED MENU AUTO KEYLOCK SEC EVENT LOG B e e m 5 2 Menu Operation Instruction ITEM FUNCTION QUICK START MENU View amp change the settings of the quick start menu items Bumeu Enter exit the quick start menu Aa Make the selection Change the setting a Go to the upper layer or sub layer Make the selection a ENTER Confirm the password entering In the quick start menu move the cursor to the icon Y and press V button Y ADVANCED MENU to enter the advanced setting menu a ENTER Go to the sub layer of the advanced menu T MENU a Under the sub layer of the advanced setting menu use this button to confirm the settings and go back to the upper layer gt NEXT Move the cursor to this item and press button to go the next page BACK Move the cursor to this item and press gt button to go the next page Other operations in the advanced menu are the same as in the quick start menu
5. The DVR will automatically detect the video system of the camera please make sure that the cameras are properly connected to the DVR and power supplied before the DVR is turned on Note If you want to make a video backup with audio please connect audio cameras to the channels which support the audio function CH13 CH14 CH15 and CH16 2 MONITOR Connect to MAIN monitor for video output 3 Audio IN 1 2 3 4 Connect to audio sources such as cameras equipped with the audio function When users start recording the audio input will also be recorded with corresponding video channel Note The audio source connected to the Audio 1 will be recorded with the video of the CH13 The audio source connected to the Audio 2 will be recorded with the video of the CH14 The audio source connected to the Audio 3 will be recorded with the video of the CH15 The audio source connected to the Audio 4 will be recorded with the video of the CH16 4 Audio OUT Connect to a monitor or speaker with 1 mono audio output 5 IR Connect the IR receiver extension line for remote control 6 EXTERNAL I O Insert the supplied 15PIN DSUB to this port for connecting external devices external alarm etc For detailed I O port PIN configuration please refer to APPENDIX 2 PIN CONFIGURATION in the user manual 7 LAN Connect to Internet by LAN cable 8 LINKACT When your DVR is connected to the Int
6. USB memory device as FAT 32 format first Step 2 Get the upgrade files from your distributor and save the upgrade files in your USB flash device do not change the file name 4 Step 3 In the SYSTEM INFO menu move the cursor to UPGRADE and press aa button to enter Step 4 Select YES and press a button again to confirm upgrade 2 UseAP software to remotely upgrade firmware or OSD Step 1 Save the upgrade files at your PC do not change the file name and then login to the AP software Step 2 Press Me button on the AP software control panel to enter the AP upgrade window Step 3 Enter the user name password IP address and port number of the DVR Step 4 Press Add to select the provided firmware and OSD files Step 5 Then press Upgrade Firmware button to start upgrade 4 5 Search 1 Search by List Press LIST button on the DVR control panel to show the list for all types of the recorded files Choose the list you want to view and press aa button to start playback 2 Search by Time In the W EVENT LOG menu list move the cursor to QUICK SEARCH and press button to enter the quick search menu You can search any specific events by time Year Month Day Hour Min and directly play the file you find 5 1 Menu Configuration CHANNEL TITLE STATUS EVENT STATUS CHANNEL STATUS IMAGE SIZE 5 RECORD QUALITY QUICK START MENU ias IMAGE PER SECOND o KA E TIMER
7. settings and go back to the upper layer 6 LIVE Press this button to stop the playback and return to the live mode T EH nu EH H Quad display selection Under the live or playback mode press one of these four buttons to select the quad display mode EH Display Quad 1 mode 4 cut view of CH1 CH2 CH5 and CH6 H Display Quad 2 mode 4 cut view of CH3 CH4 CH7 and CH8 EH Display Quad 3 mode 4 cut view of CH9 CH10 CH13 and CH14 Ha Display Quad 4 mode 4 cut view of CH11 CH12 CH15 and CH16 8 m Ta a Hs single channel selection under quad selection mode In the quad display mode press one of these four buttons to select the channel display R Display the upper left channel of the selected quad mode Display the upper right channel of the selected quad mode a Display the lower left channel of the selected quad mode Him Display the lower right channel of the selected quad mode 9 HH HH Lh Lh 16 cut channel display 9 cut channel display Quad Sequence Full Sequence Press one of these four buttons to switch the channel display or to activate the sequence mode HE Display 16 cut display HH Display 9 cut display Press this button to activate the Quad Sequence mode and press the button again to exit Press this button to activate the Full Sequence mode and press the button again to exit 1 4 7 0 AN 10 OQ sO sO sO Number buttons for password enterin Use these fo
8. eo input port with a coaxial cable or RCA lines with BNC connectors The DVR will automatically detect the video system of the camera Note Note For detailed DVR video input output ports please refer to section 2 3 Rear Panels at page 4 For detailed camera operation please refer to its own manual If you want to make a video backup with audio please connect audio cameras to the channels which support the audio function CH13 CH14 CH15 and CH16 3 3 DVR Power Setup This device should be operated only with the type of power source indicated on the manufacturer s label Connect the indicated AC power cord to the power adaptor and plug into an electrical outlet Power LED D will be on as blue It takes approximately 10 to 15 seconds to boot the system 4 BASIC OPERATION 4 1 Recording This device offers non stop recording mode If the power is off accidentally the recorded video data will not be lost and is safely stored in the HDD The device will return to the original recording status after the power is on again When the HDD is full this device will overwrite 8GB data from the oldest for continuous recording without notice 1 Continuous Recording Symbol When the DVR is properly connected with camera you can see the sign on the screen 2 Event Recording Symbol When the motion alarm detection is activated once motion or external alarm happens you will see the sign b motion or
9. ernet this LED will be on 9 DC 19V Connect to the supplied adaptor 3 CONNECTIONS AND SETUP 3 1 Install HDD Step 1 Step 2 Step 3 Note Step 4 Step 5 Step 6 Step 7 Loose the screws on the upper cover and open the upper cover of the DVR Screw out the L shape HDD brackets Two brackets are used to secure a HDD and there are 4 of them Get a suitable brand HDD and set the HDD mode Master or Slave HDD mode setting rule Master if you want to install the HDD to the place near the back panel Slave if you want to install the HDD to the place near the front panel Attach the bracket to one side of the HDD and align the screw holes of the bracket with the HDD s screw holes screw the HDD onto the HDD bracket two screws for each side Then do the same thing to the other side of the HDD screw the two HDD brackets back to the DVR base Connect the HDD to the power connector and IDE BUS make sure to align the HDD precisely for pin connection For IDE BUS connection Connect to the blue IDE BUS connector If the HDD mode is set to Master Connection to the gray IDE BUS connector if the HDD mode is set to Slave Close the upper cover of the DVR and fasten all the screws you loosened in Step 1 3 2 Camera Connection The cameras must be connected and power supplied before the DVR is turned on Connect the camera with the indicated power supply And then connect the camera video output to the DVR vid
10. me rewind 3 Stop Pressing STOP button under playback mode the screen of this device will return to live monitoring mode 4 Slow Playback Press SLOW button to get 1 4X speed playback and press twice to get 1 8X speed playback 5 Audio Playback 0 1 cH Use these two buttons to select the live or playback sound of the audio channels J Icon means Live audio of the 1 audio channel Icon i means Playback audio of the 1 audio channel Icon Gh means Live audio of the 2 audio channel Icon i means Playback audio of the 2 audio channel j Kh Icon K means Live audio of the 3 audio channel Icon i means Playback audio of the 3 audio channel j ch Icon H means Live audio of the 4 audio channel Icon i means Playback audio of the 4 audio channel Icon K means The audio channel are not selected Note If you want to make a video backup with audio please connect audio cameras to the channels which support the audio function CH13 CH14 CH15 and CH16 4 3 Key Lock and Unlock 1 Key Lock On Press o button on the DVR control panel to lock keys Or set the time out after which the key lock function is activated Never 10 SEC 30 SEC 60 SEC 2 Key Lock Off Enter the DVR password to exit Key Lock mode 4 4 Upgrade Firmware Multilanguage OSD Upgrade 1 Use USB to upgrade firmware or OSD Step 1 Format the
11. o the upper layer 16 LIST To quick search the recorded files by event list press this button to show all types of the event lists ALARM List the information of the alarm trigger recorded files MANUAL List the information of the manual recorded files The DVR will save one recorded file once any recording setting is changed MOTION List the information of the motion trigger recorded files SYSTEM List the information of the system recorded files The DVR system will save one recorded file every one hour TIMER List the information of the timer recorded files 17 LATEST Press this button to playback the latest recorded video 18 STOP Press this button to stop playback and return to the live mode 19 SLOW Under the playback mode press this button to slowly playback the recorded file by 1 4 speed or 1 8 speed 20 lt lt El p gt gt Under the playback mode press these buttons to fast rewind pause fast forward the playback file 2 2 Remote Controller If you want to remove the control panel from the DVR to use as a remote controller please switch the lock button to the right lt unlock mode Due to the different panel layout please place the vertical panel sticker on the controller for operation convenience For the detailed instruction please refer to the remote controller Manual 2 3 Rear Panels 1 INPUT 1 16CH Connect to video sources such as cameras Note
12. ur buttons to enter the DVR password 11 cH o cut Use these two buttons to select the live or playback sound of the audio channels h Icon q means Live audio of the 1 audio channel Icon i means Playback audio of the 1 audio channel 2h Icon Q means Live audio of the 2 audio channel Icon i means Playback audio of the 2 audio channel Icon means Live audio of the 3 audio channel Icon means Playback audio of the 3 audio channel J J 2 4 Icon q means Live audio of the 4 audio channel Icon i means Playback audio of the 4 audio channel Icon Q means The audio channel is not selected Note If you want to make a video backup with audio please connect audio cameras to the channels which support the audio function CH13 CH14 CH15 and CH16 2 12 o Key lock Press this button to lock keys on the DVR front panel AN O 13 amp Digital zoom Press this button to enlarge the image of the selected channel 14 A V a Press one of these direction buttons to move the cursor up down left right Under DVR menu mode these direction buttons can use for the following operation A V Make the selection Change the settings lt gt Go to the upper layer or sub layer Make the selection 15 aa Confirm the password entering Under the advanced menu use this button to confirm the settings and go back t
Download Pdf Manuals
Related Search