Pyle Subwoofers User Manual
Contents
1. Mounting the subwoofer 1 Find a suitable location in the vehicle in which to mount the amplifier A typical location is shown below Vehicle seat 2 Make sure there is sufficient air circulation around the intended mounting location 3 Mark the location for mounting hole screws by positioning the cabinet where you wish to inst all it Make a small mark to identify the position and remove the unit Thoroughly clean the area you plan to attach the subwoofer using a vacuum cleaner Then attach the supplied double adhesive tape and put the subwoofer in the place and press down on it securely Troubleshooting If you experience operation or performance problems with this product compare your installation with the electrical wiring diagram on the previous pages If problems persist read the following troubleshooting tips which may help eliminate the problems PROBLEM POSSIBLE REASON SOLUTION e NO 12v to power wire e Check fuses and connections to battery Not switching on Power No power to remote wire Check remote on connections to head unit LED not on e Replace fuse with correct type and e Fuse broken parade ches hon e Replace fuse with correct type and Not working but status amperage D on e M l o ove unit to vented area e Amplifier too hot e Turn head unit down e Head Unit e Check heed unit volume level No sound e Ensure you have set up the amplifier e Gain control not set2. or heavier cable from this fuse to the amplifier location Then connect the fuse holder to the BAT T connection on the subwoofer rear panel Chassis ground point to REMOTE TURN ON terninal of head unit Battery Remoter Level Control Connection SHIFT Instal the remote control securely under the dash orina similar location where using it will not distract the driver Low Level Input Wiring Low level RCA input wiring is preferred for best audio performance Most trunk or hatchback installations will require a 15 20 foot RCA cable while pickup trucks and under seat installations will require a 6 12 foot RCA cable Always use a high quality cable NOTE Do not connect BOTH the high level and low level inputs from your receiver to your amplifier at the same time lt gt 4K S QO ooo El O E 12V REMOTE GROUND Hs To Audio 5 Outuputs of head 5 660555 unit or signal processor High Level Input Wiring The high level input s
3. should only be used when your receiver lacks RCA outputs If the RCA outputs are not present connect the speaker outputs from the receiver to the high level input connector of the amplifier Be sure to observe polarity to avoid audio phase problems NOTE Do not connect BOTH the high level and low level inputs from your receiver to your amplifier at the same time 2 GREEN BLUE 1 2 PURPLE TO Speaker Terminals of head unit Introduction With the PLBASS10 we are introducing a low profile amplified subwoofer Low enough to easily fit below the seat of your car This system offers you a quick and easy way to add a high powered subwoofer system to your audio system The integrated amplifier in the PLBASS10 features both high pass and low pass crossovers and a control for adjusting the input sensitivity from 0 2V to 3V Both high level speaker level and low level RCA type inputs are present making this a universal solution for use with any head unit or other input source For further flexibility in the use of a subwoofer a variable bass boost control has been included You can control the subwoofer level with the remote level control module What is included When first unpacking your new amplified subwoofer please check first that the package contains all of the items below If s
4. up i gain level control e Connections e Check all power remote on and ground connections PYLE PYLE Chopper Series PLBASS10 10 Super Slim Active Subwoofer OWNER S MANUAL Congratulations on your purchase of a PYLE PLBASS10 Slim Amplified Subwoofer It has been designed engineered and manufactured to bring you the highest level of performance and quality and will afford you years of listening pleasure Thank you for making a PYLE your choice for car audio entertainment PLBASS10 1000 Watts Max 10 Super Slim Active Subwoofer e 10 Slim woofer e RCA low level input e High level input e Green amp red LED power status indicator e Remote level control e Phase shift switch 0 or 180 e Adjustable input sensitivity 0 2V 3V e 0 to 12dB variable Bass Boost 45Hz e Low pass filter 50 150 Hz e Soft delay remote turn on e Thermal short and overload protection circuits Fuse 2x20A Max power 1000 Watts RMS Power Amplifier 100 Watts Slim woofer 250 Watts e Dimension 15 X11 8 X 3 Weight 14 1 Lbs Power Connections Connect the ground terminal to the closest point on the chassis of the vehicle Keep this ground wire to less than 39 100 cm inlength Use 8 gauge or heavier wire Connect the remote terminal to the remote output of the head unit using 16 gauge or heavier wire Connect an empty fuse holder within 18 45 cm of the car battery and run 8 gauge
5. ave the control at this setting outputs for the audio source for the PLBASS10 Use the supplied cable and connect the outputs properly as shown in the connection diagram BASS BOOST in this manual The bass boost feature will increase the sound level the bass frequencies 3 FUSE LOW PASS FILTTER The fuse is rated at 20A Do not use a fuse with a different value and This control permits you define the frequency range you want the subwoofer amplifier to receive The subwoofer will reproduce all sound BELOW the NEVER replace the fuse with a wire or coin frequency you set If the rest of your system is weak on the mids you may wish to set this D POWER TERMINALS control relatively high If the midrange is well covered by the rest of your system you will probably want the subwoofer to only receive lower frequency signal REMOTE LEVEL CONTROL PORT Attach the included remote level control to control the volume level of the subwoofer independently PROTECT LED INDICATOR PYLE UNIVERSAL SUBWOOFERS
6. omething is missing contact the store where you purchased the product PLBASS10 amplified subwoofer e Remote subwoofer level control e Remote subwoofer control cable e High level input wire e Mounting hardware Front panel controls and features Rear panel controls and features M POWER ON LED INDICATOR D PHASE SHIFT Use this switch to help compensate for time alignment problems in the system Such problems usually result from having the subwoofer at a different distance from the listener than the other speakers in the system M LOW LEVEL RCA INPUTS Low level inputs are the recommended way to introduce the audio signal Gea GAIN CONTROL _ to the subwoofer if RCA outputs are present on your head unit or other er you have installed your system turn this control to minimum Turn the head unit on and the subwoofer will turn on via the remote signal source such as a sound processor connection Turn the head unit volume to about 2 3 full level Slowly turn up the subwoofer input gain control until you hear a small HIGH LEVEL speaker level INPUTS amount of distortion Then reduce the level until the distortion is If your head unit does not have RCA outputs you can use the speaker completely gone Le
Download Pdf Manuals
Related Search