User Manual
Contents
1. If camera lens adheres with dust please use special lens paper to clean up D 13 When disassemble the Acrylic DOME shield please wear cotton gloves to process in order to avoid surface of the product being scraped II Installation Instruction of the Acrylic Dome Shield 1 Remove Acrylic DOME shield Please do not scrape the Acrylic shield It is recommended to wear cotton gloves when operate 2 As shown in the figure below first take the flexible flat cable through connector above the base plate and buckle it on the connector Then buckle the cable on the connection below the CAMERA 3 Lock the CAMERA up and fix the screws 4 Install Acrylic shield Fig 2 1 Installation of the Acrylic Dome Shield Acrylic Dome Shield 3 M4x8 screw 4 M5x15 screw Bracket Outer Housing Inner Housing Acrylic Shield Holder Ring Acrylic Dome Shield 4 M3x6 screw III Install Bend Tube Style Bracket Fig 3 1 Connecting the dome to the wall mount with the bracket 3 M4x8 screw 4 5x15 screw Bracket Outer Housing Inner Housing Acrylic Shield Holder Ring Acrylic Dome Shield Fig 3 1 Wall mount bracket installation IV Description of Wiring Figure 4 1 Color code of wiring Video Out gt AC24V RED AC24V BLACK RS485 YELLOW RS485 ORANGE V Function Description High Speed Dome Video Camera is an all in one high tech monitoring product whi2. General Failure Analysis Table Fig 7 1 Troubleshooting List Problem i Possible Reason Descripti After power on no motion and no image j Power supply module is i damaged or power is not ailure occurs on Self test is exceptional there is image but with motor noise wu Self test is normal but there is no image Change power that meets requirements It jl is recommended to place the power switch ar the Dome device Correct Power is not enough Video line is connected Eliminate Self test is successful but can t control osition of Dome device Re select i controller Re power on Control signal line is poor Eliminate Dome device is not Re power the host on controllable Confirm terminal resistance 2 Add code distributor Iris of the Dome device is not controllable se control command to set iris to manual i Status and iris can be controlled i Iris is in manual status 12 VIII Main Technical Indexes i Power i AC24V 2A i Weight i 3 5Kg Specification Installation gOS Lis ee OO a rece aces At ciseradeszer tone asta asta seecctecenctecenateatetastudlan i Operating PASEN ets Temperature iO C790 C normal rage suntan i Horizontal i 0 240 s Basic i Vertical i 0 60 s Function i Preset position Dome enna POS aaa es a asc CCL a E a Scanning i i Function racks depending on different protoco
3. User Manual TeleEye DM 567 DM 569 High Speed Dome gt Before attempting to intall or operate on this product please read this manual carefully and keep it for future use www TeleEye com TABLE OF CONTENTS I Notice J 2 IL Installation Instruction of the Acrylic Dome Shield 4 III Install Bend Tube Style Bracket 5 IV Description of Wiring 6 V Function Description 6 VI Function Setting TJ 8 VIL General Failure Analysis Table 12 VIII Main Technial Indexes 13 I Notice Signal Communications Limited reserves the right to make improvements to the product described in this manual at any time and without prior notice This manual is copyrighted All rights are reserved This manual may not be copied reproduced or translated in whole or part without prior consent from Signal Communications Limited Tele Eye is a trademark of Signal Communications Limited and is registered in China Hong Kong US and other countries All other trademarks are the property of their respective owners Copyright c 2005 Signal Communications Limited A Member of Te eEye Group All rights reserved Versio
4. al length and saved in the nonvolatile memory Support Dome device to scan between two points horizontally and the scanning speed can be adjusted Provide setting of scanning track and select cruise track function Self test can allow to store track that user edits arbitrarily and information power off memory depending on user s operation keyboard or DVR function 4 New added functions 1 Long focus speed limited function Dome device can auto adjusts its manual pan tilt speed according the current focus length of video camera Closer the object become slower the pan tilt speed becomes which ensures that video camera can scan objective quickly and correctly Line scanning position freely selectable With different setting Dome device can scan between arbitrary two points within less than 180 and scanning speed is adjustable continuously related with communication protocols Programmable six cruise tracks Each track has 16 points preset position and the dwelling time and call speed upon each preset position can be set as well Intelligent involatile memory recording current setting and state If the dome is line scanning or running a track and then power off current setting and work states would be saved When it is powered on again it will be working in the same state as that before it is power off It dispense with setting again Home position Home function is available when it is set at ON namely the dome camera will r
5. ch integrates high definition color video camera universal gear change pan tilt and multi function decoder This product furthest reduces the tedious processes of connection and installation between system parts and thus increases system reliability Also the video camera is very easy to install and maintain has many features such as perfect shape short response time fast pan tilt simple operation etc 1 Integrated multi protocol decoder a Built in decoder consists of multi protocol and can integrate up to 4 communications protocols Communication serial baud rate is adjustable 2400 4800 9600 and 19200 bit per second Using the simple finger switch inside the Dome device the product can be compatible with domestic and foreign main systems and has very high compatiblilty b RS485 serial control address of Dome device is from 0 255 2 Integrated full view rotary station a Horizontal 360 unlimited continuous rotation and rotation rate can be adjusted from 0 5 240 degree sec continuously Vertical rotation range is O 90 and rotation rate can achieve 60 degree sec b Low speed operation has features of stable ultra low noise and image without jitter c 180 auto reverse realizes full view monitoring without blind area and position precision achieves 0 2 3 Intelligent Nonvolatile power off memory operation a Provides more than 50 preset points including pan tilt position and preset foc
6. eturn home position if user has no action for a period of time and user can adjusts this duration time The dome camera shall not return the home position if it is on tour state If no home function is needed when the dome camera is stopped set the option at OFF i e Press Preset for 2 sec key in 100 and then enter The home position is First preset point VI Dome Setting 1 Before installing the dome device set the dip switches to match the communication protocol transmission baud rate and dome address ID of the control device Figure 6 1 Location of the ID number dip switch and Protocol Baud rate dip switch PROTOCOL BAUD RATE Dome Address setting aa ia PROTOCOL SELECT ID NUMBER 2 Address setting of Dome device first 8 digits of SW1 Coding Description e Dome Address is represented in binary format where ON represents 1 OFF represents 0 e The above table only present the settings of 0 20 address code The setting of the rest of the address code 0 255 can be deduced e Address coding range 0 255 Figure 6 2 Setting of Dome Device ID O represents ON Figure 6 3 Setting of Protocol and Baud Rate On Off Protocol Status Default Serial Transmission Rate Protocol Type TeleEye DM2 Baud Rate 2400 BPS x 4800 BPS O 9600 BPS O 19200 BPS O O 4 Coding description of protocol and serial transmission rate When setting co
7. ls 13
8. mmunication protocol of the Dome device first 4 bits of SW2 and default serial transmission rate of the protocol last 2 bits of SW2 if default serial transmission rate of the protocol does not match with serial transmission rate of host please set the default serial transmission rate of the protocol consistent with the default serial transmission rate of host according to Figure 6 3 Figure 6 4 Operation Key Set Preset Point PRESET hold 2 sec N ENTER N Enter N Enter SET 1 Press and hold PRESET key for 2 seconds 2 Adjust the camera to the desired direction and focus 3 Input the preset number 4 Press ENTER 5 Repeat step 2 to step 4 if you want to set more preset point 6 Press set key to exit Call Preset N PRESET 1 Input the preset number 2 Press ENTER Set Home Position T DWELL N PRESET 1 Input a number T a value between 1 and 255 T represents the time between stoping operation to the camera and the camera s automatically turning back to the home position 10 2 Press DWELL 3 Input a preset number which you want to be your home position 4 Press PRESET Delete Home Position 0 DWELL 0 PRESET Set Preset Tour Sequence TOUR hold 2 sec S Enter N Enter N Enter N Enter Set 1 Press and hold TOUR for 2 seconds 2 Input the sequence number from 1 to 4 3 Press ENTER 4 Input the preset number represen
9. n 1 0 Limits of Liability and Disclaimer of Warranty Signal Communications Limited have taken care in preparation of this manual but makes no expressed or implied warranty of any kind and assume no responsibility for errors or omissions No liability is assumed for incidental or consequential damages in connection with or arising out of the use of the information or accessories contained herein Features and specifications are subject to change without prior notice 1 Before installing the full view High Speed Dome Video Camera please read this user s manual first 2 This unit should be operated only from the type of power source indicated on the marking label found at the power adapter If you are not sure of the type of power supply you plan to use consult your appliance dealer or local power company For units intended to operate from battery power or other sources refer to operating instructions 3 Inside the Dome device are precise optical and electrical instruments Heavy pressure shock and other incorrect operations should be prevented during the processes of delivery storage and installation Otherwise it may cause damage on the product 4 Please do not remove and disassemble any internal a ON components from the Dome video camera by yourself in order to avoid normal usage being impacted There is no parts inside OQ pr the device which can be repaired by the user himself 5 Always conform to national and l
10. ocal safety codes during installation Adopt the special power provided with the Dome video camera During transmission RS 485 and video signal should be retained enough distance with high voltage equipments or cables When necessary thunder proof surge proof and other protecting measures should be carried out 6 Please avoid exposing the Dome video camera to rain or the humidity etc Please do not use the product in humid place If the video camera is installed in outdoor area please ensure the device being protected by a weather proof sealed shield Exposure to open area should be avoided 7 Do not install this dome camera in a place exceeding the required environment conditions such as temperature humidity and power supply specifications 8 Whether the high speed Dome video camera is powered on or not avoid the video camera aiming at the sun or glary object Lengthy exposure to static bright object is also not recommended 9 Please do not use strong or caustic washing lotion to clean the main body of the high speed Dome video camera After dirt is cleaned up please use cotton fabric to clean the product Stubborn dirt should be cleaned up with neutral washing lotion and then dried gently with soft cotton fabric 10 Shall use the high speed Dome video camera carefully and avoid being stroked or shocked If operating is improper the product may be damaged 11 Install the High Speed Dome Video Camera in a place with enough holding force 12
11. ting the first tour point 5 Press ENTER 6 Repeat step 2 and step 3 for other tour point 7 Press SET to exit Activate Preset Tour T DWELL S TOUR 1 Input a number T where T represent how much second the camera rest on one tour point before it move to another tour point 2 Press DWELL 3 Input S where S is the tour sequence number 4 Press TOUR Delete Preset Tour TOUR S DEL 1 Press TOUR 2 Input the number S where S represents the tour sequence number 3 Press DELETE Auto Pan SCAN 0 ENTER Set auto pan left limit SCAN 1 ENTER Set auto pan right limit S SCAN Activate auto pan If S is within 1 80 the scan rate is slow If S is within 81 160 the scan rate is medium If S is within 161 250 the scan rate is high Focus Control Generally the camera will automatically adjust the focus to get clearer image based on the distance of the camera But you can manually adjust the focus by pressing FAR NEAR as you wish The camera will switch back to automatically when you conduct other operations such as moving the joystick Iris Control Generally the camera will automatically adjust the iris to get clearer image based on the illumination But you can manually adjust the iris by pressing OPEN CLOS as you wish The camera will switch back to automatically when you conduct other operations such as moving the joystick 11 VII
Download Pdf Manuals
Related Search