Operating Manual for OPTOCORE DD2FR-FX
Contents
1. WORDCLOCK e POWER 1 otme AER f Wm E TOU Se m ooe OWN EA frente eye E 2 2 ere ere Ei LAN 1 LAN 2 LINK 1 LINK 2 SANE1 SANE2 e VIDEO OUT our IN our IN e MADE IN GERMANY OPTOCORE mm RS485 H Word Clock IN Word Clock OUT Video IN Video OUT POWER POWER SANE 1 SANE 2 LINK 1 LINK 2 LAN 1 LAN 2 DD2FR FX MADI 1 2 2 1 4 x RS485 RS422 D Sub 9 auxiliary port for data transmission BNC Word clock input allowing synchronization of Optocore devices network from an external word clock source BNC Word clock output for synchronization of external devices BNC Video input for composite video BNC Video output for composite video 2 x SC multi single mode optical MADI inputs and 2 x SC multi single mode optical MADI outputs Mains input for power supply 2 100 240 V Mains input for power supply 1 100 240 V SANE RJ 45 interface for data transmission 100 Mbit Ethernet SANE RJ 45 interface for data transmission 100 Mbit Ethernet Full duplex full bandwidth LC type optical interface for Optocore transmission SFP multimode transceiver included singlemode transceiver option available on demand Full duplex full bandwidth LC type optical interface for Optocore transmission SFP multimode transceiver included singlemode transceiver option available on demand 100 Mbit2. 17 Principal and Auxiliary Ports nennen nennen nennen nnne nn nnne nennen enn nnne 17 RS232 Connection ecceceeeesceceneeeeeeeteaeeeeseeeeaeeeeaeeceaeeesaeessaeeeaeeseaeessaeesaeeseaeeseaeessaeeseaeessaeeseaeessaeeseeeteaees 17 Connector Hood Quality 2 1 5 2 2 xt ASS ta ete dec emit resa ce So Eeer 17 USB CONNECCION onmes 17 Word Clock Connection 17 Vid O GOMMECHIOM m 17 Mains Connectioni s e EU t UEM EL ele undas 17 Hardware Connection m 18 Network Exa imples e 19 RET sez EsTerzte tiec 23 DIMENSIONS ANG WE Lu EE 23 Warranty Au BEI 24 Elle elle Ee 25 elle taa E 25 DD2FR FX 9 25 rev 2 3 OT TOCOTSE Device Description Congratulations on your purchase of a DD2FR FX Optical Digital Network Device with Cap based SANE MADI video Ethernet and data interfaces The DD2FR FX manual will quickly demonstrate the advantages of the device and help to ease your day to day workload in a professional audio visual environment The DD2FR FX is a digital I O unit and interface to the OPTOCORE and SANE DIGITAL NETWORK SYSTEM The unit provides two SC single multimode optical MADI input and two SC single multimode optical MADI output ports allowing the
3. at both sides devices when connecting RED external equipment to the RS485 ports MHE Locking system acc to 4 40 UNC SANE Synchronous Audio and Ethernet MADI In MADI Out Out A device compatible with 10 100MB Fast Ethernet can be eem connected to a SANE port for Ethernet data communication RS232 Bridged Use 1 modem cable male female to connect to PC Dee lebe L t Locking system acc to 4 40 UNC USB Port Channel GND VBUS EAA USB device connector WE ECH EES ES ER DD2FR FX 21 25 rev 2 3 OPTOCORE BI C Cable The D Sub 9 BI C enables the bi directional transmission of control data between DD2FR FX and Yamaha HA Remote port The RS485 Ports 3 and 4 of the DD2FR FX are used DD2FR FX Auxiliary Port 4 x RS485 COM RS422 X3 X4 I Os X3 RxD D Sub 9 male X4 Tx D Fastening system 4 40 UNC D Sub 9 female Fastening system 4 40 UNC X Twisted pairs GND Shield DD2FR FX 22 25 rev 2 3 OFTOCOR E Technical Specifications MADI Ports Convention AES10 1991 AES10 2003 Inputs Number Connectors 2 optical MADI digital audio channels 56 or 64 per Input Outputs Number Connectors 2 optical MADI digital audio channels 56 or 64 per Output Data rate 125 Mbps Output Input Output 1310 nm typical Max cable length 50 125 um 1500m 5000ft Word clock Hardware standard BNC 75 O Data rate Depending on selected sampl
4. NOTE This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communication Operation of this equipment in a residential area is likely to cause harmful interference in which case you will be required to correct the interference at his own expense Changes or modifications not expressly approved by Optocore GmbH could void the user s authority to operate this equipment Industry Canada Compliance Statement This Class A digital device complies with Canadian ICES 003 Avis de conformit la r glementation d Industrie Canada Cet appareil num rique de la class A est conforme la norme NMB 003 du Canada The authorised declaration and compatibility certification lies with the manufacturer and can be viewed on request Responsible as manufacturer is OPTOCORE GmbH Lohenstr 8 82166 Munich Gr felfing Germany represented by Marc Brunke Managing Director N B The awarding of the CE label confirms the compliance with legal directives issued for the manufacturer and marketing of electronic and electrical devices As such the CE label is
5. 2 A redundant network with one DD2FR FX unit In case an interruption occurs at position a as illustrated above this will only result in a loss of redundancy This also applies to the very unlikely case of a device failure The redundancy of the ring can be reestablished simply by connecting the in and out fibre with the help of an adapter and a new device can be integrated at any time DD2FR FX 18 25 rev 2 3 OFTOCOR E Network Examples DD2FR FX devices can be used as a fibre optic extender for SCH party consoles to transport all audio signals and control data between stage unit and FOH local equipment Below configurations with LAWO and Soundraft consoles are presented Studer signals can be transported similar to the examples below Connecting AVID console with its stagerack requires a special firmware version which supports AVID s Snake protocol ANALOG INPUTS ANALOG OUTPUTS Dallis Frame I O Soudcraft Stage Rack MADI CARD WORD CLOCK IN OUT a camem DD2FR FX LINK 1 LINK 2 BUU S COUEN M IN OUT LINK 1 LINK 2 DD2FR FX MADI 1 MADI 2 IN OUT IN OUT E ME EC ES es WORD CLOCK OUT OUT IN MADI CARD IN MADI Soundcraft Local Rack Lawo HD Core Fig 3 Redundant network with two DD2FR FX in a 64 send 64 return configuration with Lawo and Soundcraft DD2FR FX 19 25 rev 2 3 OT TOCOTSE Second example shows how to use OPTOCORE devices as
6. Hood Quality Locking screws for D Sub connectors should be compatible with 4 40 UNC Care should be taken in selecting the right type of connector hoods in order to fulfil the requirements of EMl radiation directives Full metal connector hoods should be used approved acc to VDE 0871 FCC 20780 and EMC directive 2004 108 EG providing attenuation 40 dB between 30 MHz up to 1 GHz The shield of the cable should have contact to the connector hood USB Connection Use a USB A to USB B cable between PC and Optocore device LAN Connection Use standard twisted pair cable Cat 5 Cat 6 with RJ 45 connectors Word Clock Connection Use 75 Q coaxial cable with BNC connectors Video Connection Use 75 Q coaxial cable with BNC connectors Mains Connection Standard power cords with IEC C13 connectors DD2FR FX 17 25 rev 2 3 OPTOCORE Hardware Connection An exemplary network with four devices is shown in Fig 1 It is established by creating a non redundant loop simply by daisy chaining the units and monitoring the three status LEDs of each device as revealed through the signal flow in diagram below There is no need to worry about the sequence of neither IDs nor which of the two LINKS of a device is used for connection The only condition is that an optical input must be connected to an optical output During the self configuring of the network the system word clock master will be automatically determined If the DD2FR FXs and other
7. a stage I O for 3 party mixing consoles Up to four Emulation Modes are available in the system allowing remote preamp control from Soundcraft Studer Lawo SSL and Yamaha After enabling Emulation Mode using OPTOCORE CONTROL software all adjustments as gain Phantom power and Pad switches can be set directly from console without any additional control unit or software Connection between console s Local rack and OPTOCORE NETWORK is made using MADI digital signal 8 ES ANALOG INPUTS ANALOG OUTPUTS 33 40 1 8 i 16 ANALOG INPUTS 1 16 ANALOG INPUTS 1 16 33 40 OUT IN OUT IN OUT IN OUT IN OUT IN OUT OUT IN OUT IN IN OUT IN OUT LINK 1 LINK 2 DD2FR FX MADI 1 WORD CLOCK IN OUT OUT OUT IN WORD CLOCK MADI CARD IN Soundcraft Local Rack 8 ANALOG INPUTS ANALOG OUTPUTS 1 8 X6R FX 16MI X6R FX 16MI X6R FX 8MI 8LO X6R FX 8MI 8LO LINK 1 LINK 2 LINK 1 LINK 2 LINK 1 LINK 2 LINK 1 LINK 2 IN Fig 4 Redundant network with one DD2FR FX and four X6R FXs 48 analog inputs and 16 analog outputs are available at the X6R FXs For more details regarding the connecting of 3 party consoles please refer to Quick Start Guides for each console or Optocore Control Software Manual DD2FR FX 20 25 rev 2 3 OFTOCOR E Connection Tables Auxiliary Ports 4 x RS485 Channel Please assure correct polarity and
8. controlled centrally over the Optocore network with the exception of the initial configuration of the unique identifier ID of the device The OPTOCORE CONTROL software is capable of running multiple instances on the same PC or by using the OPTOCORE CONTROL software s Client Server mode Please note Please refer to the Optocore Quick Start Guide for the basic system configuration and setup For more detailed setup please refer to the Optocore Software Manual Optocore bandwidth allocation The standard bandwidth allocation of an Optocore network is as follows Audio 256 Channels 9 48 kHz 1 Gbit network 768 Channels 9 48 kHz 2 Gbit network RS485 Data 32 Channels Video 3 CVBS Video Channels Ethernet 100 MBit Fast Ethernet f the network is used for transport of Ethernet compatible data the capacity is reduced to one CVBS video channel plus 100 Mbps Fast Ethernet Please note Optocore R Series devices equipped with 2Gbit fibre transceivers are required for 2Gbit network operation DD2FR FX 15 25 rev 2 3 OT TOCOTSE SANE bandwidth allocation The standard bandwidth allocation of a SANE link is as follows Audio 64 Channels 48 KHz Ethernet 100 MBit Fast Ethernet DD2FR FX 16 25 rev 2 3 OFTOCOR E Connectors and Cables Optical Connection Multimode transceivers connected using a 50 um OMS fibre cable can be used for applications requiring
9. misprints The operating manual is regularly revised and updated Modifications which serve the purpose of technical improvement of the device may be carried out without prior notification e Transport and Shipping Always ensure careful handling of the device The device should be transported and shipped in shock absorbing transport cases If these are not available we recommend well padded packaging such as the coated carton in which the device was delivered We strongly advise against the use of light weight flight cases without shock absorbing rack in rack mounting e Environments This device can be used in E1 E2 E3 E4 or E5 environments as listed below according to the harmonized European standards EN55103 1 and EN55103 2 Electromagnetic compatibility Product family standard for audio video and audio visual and entertainment lighting control apparatus for professional use E1 Residental E2 Commercial and light industrial E3 Urban outdoors E4 Controlled EMC environment e g broadcast and TV studio E5 Heavy industry The product is intended for the use in moderate climate e Ventilation Do not block or cover any ventilation openings Install the device in accordance to the operating manual Allow for sufficient space around the units at least 200 mm z 7 87 free space behind the rear panel of the device and make sure to allow for air circulation near the ventilation openings on both sides of the device Keep the r
10. not a seal of quality but rather proof that the device bearing the CE label conforms with the electromagnetic compatibility standards laid down in the above named testing regulations Munich 11 12 2013 Mowe Kyle Marc Brunke DD2FR FX 7125 rev 2 3 Page intentionally left blank OFrTOCOR E DD2FR FX Dual Fiber MADI device for Optocore and SANE Table of Contents Important Safety Instructions ssesssssessseeseeeeneeneennenen eene nnnet nenne nnn ee nnn einn en nen rete eterne nennt 3 Purchaser Into nim ator rc 4 EE Conformity fish Hit ei Ae ES 7 Device DeScriptloniciisiests EID 10 Front Paneles e ee SLs dE IINE HS 12 arii Em 13 Device Details M EE 14 Optocore Fibre Optic Connection 1 coiere eicere rater idc beer eie Pee enden De able te Leto esse e eed EU vB 14 MIN ec EE EE Ee 14 WE 14 5485 Auxiliary Ports a rene ed e die HEEL edi ic RRR eee 14 WV OC OC EE 14 Vue ISI H E 14 Ethernet lt IRI E e 14 POWwSTSUPDIV LM 15 IU CUBE EEEER 15 E lu e EE 15 Optocore bandwidth allocatton nennen enne 15 e Ee Elle Ve ele LTE 16 Contectors and ele 17 Optical enee E M 17 MADI POS e etm 17 SANE POMS I M
11. 825 1 FDA 21 CFR 1040 10 and 1040 11 External objects and or liquids with the device Never push objects of any kind into the device through openings in the casing They may come into contact with dangerous voltage points or short out parts that could result in fire or electric shock Never spill liquid of any kind on the device DD2FR FX 5 25 rev 2 3 OT TOCOTS E e Cables and Accessories Only use attachments that are specified by the manufacturer of the device Use high quality properly terminated cables to connect the device The device should only be used with optical fibre cables that are specified for use with the devices optical transceivers and within the specified power budget of the optical transceivers When not in use ensure that the optical connectors on the device and the optical fibre cables are covered with the provided caps Do not place this device on an unstable table tripod cart etc The device may fall which can cause injury and serious damage to the device Any mounting of the device should follow the manufacturer s instructions and should use mounting accessories recommended by the manufacturer of the device e Servicing Do not attempt to service this device yourself The device contains no user serviceable parts components or controls The operation of an opened device is not permitted Such operation can lead to damage of the device s components due to lack of air flow through the device The dev
12. DD2FR Device ib ei SPTOCORE s 9 P up HEH i 7 OPTICAL NETWORK m 90 676 v SYSTEM DUAL MADI VIDEO DATA MODULE LP Lei Ses use NOONE Sh Sv CE wen DEn Sy E orrocone A Operating Manual for OPTOCORE DD2FR FX DUAL MADI SANE VIDEO DATA MODULE WITH ETHERNET Optical Digital Network Device Copyright 2015 All rights reserved OPTOCORE GmbH Lohenstr 8 82166 Munich Gr felfing Germany DD2FR FX Operating Manual Rev 2 3 Page intentionally left blank OFTOCOR E Important Safety Instructions Please read this manual carefully Please keep this operating manual in a safe place Heed all warnings Follow all instructions This device may only be used in accordance to the information provided in this operating manual Ensure that all recommendations especially the safety recommendations as detailed in this operating manual are followed before and during the usage of the device Do not use this device near water for example in humid or damp rooms Clean only with a dry cloth Do not block or cover any ventilation slits Install the device in accordance with the operating manual Do not install or place the device near any heat source such as radiators power amplifiers or any other heat producing equipment Protect the power cord from being stepped on crushed pinched or damaged in any other way Pay special attention to plugs and sockets of the device Never switch on powe
13. E CONTROL software The software provides access to all configuration parameters and controls needed to operate the system including naming channels setting gains and phantom power routing as well as recall and capture of partial or full system configurations The software can be operated offline as well as online with level meters for all channels on the network DD2FR FX 11 25 rev 2 3 OPTOCORE Front Panel DD2FR 000 INT BNC NET N 000000 lo 441 an 08 2 96 1764 192 OPTOCORE Word Clock LED Indicates the selected word clock source INT Internal word clock The device is a system master BNC External word clock via BNC WC Input NET Word clock received from network Status LEDs of MADI Input and Output 1 and 2 INPUT SYNC OUTPUT ON MADI 56 64 1 2 3 4 5 6 7 8 AUDIO LINK SL1 SL2 OL1 OL2 System status Master LED OPTO LED SANE LED Device ID Display HEALTH LED PWR 1 LED PWR 2 LED USB plug and LED RS232 plug DD2FR FX Indicates the status of MADI Input LED ON Valid MADI frame is present LED OFF No MADI signal is present or signal is not valid Indicates the configuration of MADI Output Indicates if there is MADI protocol active MADI format and number of channels LED ON 64 CH single speed AES10 2003 LED OFF 32 CH double speed AES10 2003 Signal status of the eight channel groups each group representing eight audio c
14. Optocore devices are pre configured the network is ready to work With a PC connected to any unit in the loop and by running the OPTOCORE CONTROL software the network may be analyzed supervised parameters may be changed and the matrix can be accessed for signal routing OPTOLINK 1 OPTOLINK2 MASTER MASTER e Q i Q e DD32R FX Ip 2 TA OPTOLINK1 OPTOLINK2 MASTER OPTOLINK1 OPTOLINK2 MASTER e e e O DD2FR FX ip 1 X6R FX 1D 4 OPTOLINK 1 OPTOLINK 2 e E DD4MR FX ip 3 ones r Yd Yo OPTOLINK 1 OPTOLINK 2 OPTOLINK 1 OPTOLINK 2 OPTOLINK 1 OPTOLINK 2 OPTOLINK 1 OPTOLINK 2 OUT IN OUT IN OUT IN OUT IN OUT IN OUT IN OUT IN OUT IN S as F e mn EE 1 Fig 1 A non redundant network with one DD2FR FX unit A second redundant reverse loop can be additionally created with only one more connection from the last unit of the chain back to the first as demonstrated by the signal flow diagram in Fig 2 MASTER MASTER OPTOLINK 1 OPTOLINK 2 e e DD32R FX ip 2 Ap t OPTOLINK 1 OPTOLINK2 e o DD2FR FX iD 1 r MASTER OPTOLINK 1 OPTOLINK2 e e e X6R FX ip 4 TN MASTER OPTOLINK 1 OPTOLINK 2 OC e e DD4MR FX ip D OPTOLINK 1 OPTOLINK 2 OPTOLINK 1 OPTOLINK 2 OPTOLINK 1 OPTOLINK 2 OPTOLINK 1 OPTOLINK 2 OUT IN OUT iN OUT uN OUT IN gui A LE NS OUT IN OUT IN BEE en T SC 2 E mm EE E 1 Fig
15. RJ 45 Ethernet interface 100 Mbit RJ 45 Ethernet interface 13 25 rev 2 3 OT TOCOTSE Device Details Optocore Fibre Optic Connection The device is equipped with the Optocore FX communication module The OPTOCORE OPTICAL DIGITAL NETWORK SYSTEM utilizes Time Division Multiplex technology TDM with a Fibre Channel based 8B10B NRZI coding Static time slots guarantee a synchronous transmission of all channels at all times without the use of dynamic bandwidth or latency All signals connected to the intercom audio video word clock and auxiliary ports of the device are transmitted simultaneously on one fibre while the second fibre of the LINK Interface receives data from the network The second LINK Interface pair is identical to the first one and can optionally be used for network redundancy MADI Ports MADI Multichannel Audio Digital Interface was first standardized by the AES10 1991 for the transmission of 56 digital audio channels in one frame The revision AES10 2003 enhanced the number of channels to maximal 64 digital channels The DD2FR FX supports the formats according to both standards If an external device cannot handle a 64 channel MADI frame the ports can be set to the older AES10 standard with OPTOCORE CONTROL The DD2FR FX is equipped with two MADI input ports and two MADI output ports each transmitting or receiving up to 64 audio channels This amounts to a total number of up to 128 input channels and 128 output chan
16. additional channels Two built in Ethernet ports can be used to establish 100Mbit Ethernet LAN through the OPTOCORE and SANE networks The DD2FR FX together with R Series devices YG2 and DD6NE behaves like one 100Mbit Ethernet switch SANE ports can be used for Ethernet transport as well so up to four ports can be used to provide Local Ethernet connection via single DD2FR FX The DD2FR FX provides both word clock input and output It includes also bi directional composite video interfaces Additionally four RS485 ports allow the transport of a wide range of standards such as RS422 DMX MIDI and CAN Bus bi directional requires special firmware version In addition to the audio signals video and data signals are transmitted through the common fibre connection The dual power supply unit with automatic switchover permits a redundant power supply and safeguards against malfunctions in the event of a power supply failure The DD2FR FX is the perfect I O interface for a wide range of professional audio devices with MADI inputs and outputs such as digital consoles and I O systems The high number of channels exchanged by one DD2FR FX makes it the ideal and most cost effective interface for digital console systems The number of input channels can be defined in groups of eight by the OPTOCORE CONTROL software Only this number of channels is allocated for transmission via fibre optical connection This keeps the system highly flexible in order to build
17. are sending or receiving control data The ports and their destinations are configured in the OPTOCORE CONTROL software Word Clock Devices with Optocore SANE modules are equipped with an internal high quality low jitter clock generator as well as Word Clock inputs and outputs Any device on the network can act as the master of the network and pass Word Clock to networked Optocore SANE devices The internal networked Word Clock is available at the Word Clock output connector of each device on the network to synchronize non networked devices In standalone network configurations external synchronization is not required The Word Clock input termination can be switched on using the OPTOCORE CONTROL software s Local Settings External termination is not required to avoid cable reflections Word Clock master negotiation after any Word Clock source failure is done automatically Video Ports A video in and output is integrated for the transmission of composite video signals Up to three video channels can be transported through the Optocore network depending on configuration Ethernet Ports DD2FR FX supports Optocore and SANE Ethernet transport Two LAN ports interface with all other LAN and SANE LAN ports in the Optocore and SANE Network creating a large unmanaged virtual 100Mbit Ethernet switch DD2FR FX 14 25 rev 2 3 OFTOCOR E Power Supply The device is optionally equipped with two power inputs and power supply units If on
18. cable lengths of up to 700 m worst case Single mode transceivers connected using a 9 um fibre cable can be used for applications requiring cable lengths of up to 70 km worst case The total optical loss should be less than 6dB between transceivers For portable applications such as touring and other temporary installations ruggedized HMA Expanded Beam Connectors mounted on 1 RU panels and portable cables on cable drums are available Please refer to the Product Brochure available at www optocore com MADI Ports The MADI interfaces are equipped with SC multimode optical connectors Standard SC cables are perfectly suitable for interconnection of devices It is recommended to use multimode cable for MADI connectivity The MADI transceiver provided by Optocore supports both multi mode and single mode connectivity as long as the multimode cable is used SANE Ports Use standard fully wired twisted pair cable Cat 5 Cat 5e Cat 6 terminated with RJ 45 connectors SANE utilizes all four pairs of the Cat 5 cable two pairs for standard Ethernet transmission and two pairs for the SANE synchronous audio transport A SANE cable shall not exceed a total cable distance of 100 m Principal and Auxiliary Ports Each of the four channels requires a shielded twisted pair cable If two or more channels are wired to the same cable a common braided shield should enclose the pairs RS232 Connection Use a standard shielded RS232 cable Connector
19. does not include mechanical damages caused by misuse This warranty covers the original registered purchaser only and is not transferable This warranty does not apply to devices which have been purchased in used condition or demonstrator equipment OPTOCORE will at its discretion repair or replace a defective product providing that the defect has occurred under normal operating conditions This warranty does not cover damage from acts of God accident abuse neglect contamination unauthorised modification misuse or operation outside of the environmental specifications for the product improper site preparation or maintenance or abnormal conditions of handling This would include over voltage failures and conditions outside of the products specified ratings problems with customer supplied software or interfacing or normal wear and tear of mechanical components OPTOCORE will acknowledge the evaluation of warranty after inspection Not covered by this warranty are defects arising from electromagnetic or electrical interferences deficiency excess or surge of electrical supply air conditioning or humidity This also includes repairs made necessary by dirt abrasion moisture rust corrosion or similar conditions Devices on which the Serial Number has been removed or defaced are not eligible for warranty service OPTOCORE devices contain no user serviceable components refer to qualified service personnel for repair or upgrade The wa
20. e Please note that due to the Ecology reason standard shipment does not contain printed copy of User Manual All latest OPTOCORE user manuals can be downloaded from the website http www optocore com index php support downloads Printed version of User Manual is available on a special demand Please contact suppori 2optocore com if printed version is required Company Information Mailing Address OPTOCORE GmbH Lohenstr 8 D 82166 Munich Gr felfing Germany Telephone 49 0 89 8999640 Fax 49 0 89 89996455 Internet www optocore com Email Inqui optocore com DD2FR FX 25 25 rev 2 3
21. e power supply fails due to malfunction of the feeding power line or the power supply unit itself the device will automatically switch over to the other power supply unit In order to make the power supply redundant both power inputs must be connected to the mains supply if possible to different phases power supply systems or even better one of them to an uninterrupted power supply UPS The power supply units operate with mains voltage of 100 240 V and frequency of 50 60 Hz Thus the device can be used throughout the world without any modifications or transformers Important The switched mode power supplies operate at very high voltages Coming into contact with the power supplies can lead to considerable electric shock which may result in death To prevent electric shock do not remove any covers of the device Transmission Delay The Optocore system delay including the matrix is fixed to 41 6 us 48 kHz for all channels The additional transport delay per Optocore unit 200 ns in the network is insignificant in comparison Overall system delay is dependent on the converters used and the length of network cables in the system Assuming normal cable lengths of 700 m per link the additional delay is considered marginal The transmission delay is constant between any points in the network Control All system and device parameters are configured using the OPTOCORE CONTROL software The system can be configured and
22. e rate Up to 192 kHz Impedance Output lt 50 Input 750 Drive level Output 2 1 Vp Zero level Referring to GND 1 7V Sense level Input 2 400 MV pp Remote Control Convention RS232 EIA TIA 232 57 600 Baud USB USB 2 0 Device 12 Mbit s LAN TIA 568A B IEEE 802 3 10 100 Mbit s SANE LAN Convention Audio TIA 568A B Optocore 200 Mbit s LAN TIA 568A B IEEE 802 3 10 100 Mbit s Optical Connection Complies with 21 CFR 1040 10 and 1040 11 Power supply Type Mains voltage Frequency Power consumption Security classification Security regulations Mains connector Cooling Switch mode universal input 100 240 V 50 60 Hz 32VA Max Class 1 basic insulation connected to the protective grounding conductor Harmonised European standard EN60065 acc to IEC 950 Passive via surface and ventilation openings on both sides of the device Dimensions and Weight Front panel width height depth Rear panel width Weight 2 7 kg 4 41 Ibs Please note 483 mm 19 inch 44 mm 1 73 inch 200 mm 7 87 inch 438 mm 17 25 inch Modifications that serve the purpose of technical improvement may be carried out without prior notification DD2FR FX 23 25 rev 2 3 OT TOCOTSE Warranty and Liability Summary of Warranty OPTOCORE DD2FR FX device is warranted against defects in material and workmanship for 60 months 5 years from the date of purchase This warranty
23. ear of the rack open during operation Do not operate the device close to heat emitting equipment such as power amplifiers Leave sufficient space minimum Le RU between the device and any heat emitting devices housed in the same rack A DD2FR FX may be placed on top or beneath other Optocore products except a DD32E without additional space for up to 4 adjacent rack spaces Please note Do not populate more than 4 adjacent rack spaces with Optocore devices Maintain 1RU of empty space between each 4 RU of Optocore devices Keep the equipment rack open during operation Ensure air circulation around the devices Maintain at least 200mm 8 clearance behind the rear panel of the devices e Water and Moisture etc To prevent fire or shock hazard do not expose the device to direct sunlight dust water or rain during operation or storage DD2FR FX 4 25 rev 2 3 OFTOCOR E Cleaning Only use a dry linen cloth to clean the device If the unit is very dirty moisten a cloth using a little water and a small amount of household detergent Never use cleansing agents containing solvents to clean the device Operating and Storage Temperature Operating temperature 20 C 50 C 4 F 122 F ensure proper ventilation Storage temperature 20 C 60 C 4F 140 F Power Supply The device can be disconnected from the power supply by unplugging the power cord The power cords must be freely accessible at all times T
24. hannels LED ON Signal present LED OFF No signal present Indicates the audio link status Communication is established via SANE 1 rear panel Communication is established via SANE 2 rear panel Communication is established via Optocore LINK 1 rear panel Communication is established via Optocore LINK 2 rear panel Indicates the Word Clock Master unit Optocore communication is established SANE communication is established Indicates the identification number of the device Green Power supply to the device works temperature is below the limit Power supply 1 is working correctly Power supply 2 is working correctly USB connection for remote control and update via PC Green Indicates data activity D Sub 9 RS232 connection for remote control and update via PC 12 25 rev 2 3 OFTOCOR E 9 LAN LINK S1 S2 UP L1 L2 16 Sample Rate LED Rear Panel Indicates the Ethernet link status Ethernet communication is established via SANE 1 rear panel Ethernet communication is established via SANE 2 rear panel There is other device with physical Ethernet port enabled on the network Ethernet communication is established via LAN 1 rear panel Ethernet communication is established via LAN 2 rear panel Yellow 44 1 48 88 2 96 176 4 192 kHz _ 9 e POWER 2 ant sova soeone C matze v e ES
25. he device should be disconnected during lightning storms or when the device is unused for a long period of time Important The switched mode power supplies operate at very high voltages Coming into contact with the power supplies can lead to considerable electric shock which may result in death Never disconnect the main plug by pulling the cable always pull the plug itself Power supply cords should be routed in such a way that they are not likely to be walked on crushed pinched or damaged in any other way Pay special attention to the plugs and the sockets of the device Important A damaged power cable must be replaced immediately The device must be grounded Disconnecting the ground is strictly prohibited Ensure that the device is always grounded using the power connector Do not cover the ground connection of the power connector with any kind of insulation material Fuse There is no fuse in the device The power supplies contain circuitry that protects the device from overload Lightning For additional protection of this device during lightning storms or when it is left unattended and unused for a long period of time disconnect the power cord This will prevent damage to the device due to lightning and power line surges Disconnection from the mains power supply is only possible by disconnecting the power plug from the main socket Eye Safety This product is a Laser Class 1 product It complies with IEC 60
26. ice may not be serviced altered or modified without authorization from Optocore or an Optocore authorized distributor dealer Only qualified service personnel may carry out repair and maintenance work on the device The warranty of the device will be voided if any unauthorized maintenance or repair work has been carried out DD2FR FX 6 25 rev 2 3 OFTOCOR E CE FCC Conformity This document confirms that the DD2FR FX bearing the CE Communaut Europ enne label meets all requirements in the EMC directive 2004 108 EG laid down by the Member States Council for adjustment of legal requirements Furthermore the product complies with the rules and regulations of the low voltage directive 2006 95 EG and the Restriction of Hazardous Substances Recast Directive 2011 65 EU RoHS 2 This product bearing the CE label complies with the following standards ratified by CENELEC Comit Europ en de Normalisation Electrotechnique Electromagnetic compatibility Product family standard for audio video audio visual and entertainment lighting control apparatus for professional use EN 55103 1 Emission EN 55103 2 Immunity EN 60065 Safety requirements FCC notice This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation
27. nels per device The interfaces are SC multi singlemode optical connections The number of input and output channels exchanged at each port and transmitted on the fibre optical connection can be defined in the OPTOCORE CONTROL software for details refer to OPTOCORE CONTROL SOFTWARE Manual This keeps the matrix easy to handle and the quantity of channels per device in the network flexible Using one DD2FR FX does not automatically mean that 128 channels are allocated on the fibre connection The user is free to decide how many channels are needed for the transport of MADI in groups of eight LEDs on the front panel of the DD2FR FX indicate the number of channels received at the MADI input ports The MADI output ports always transmit the complete frame with 56 or 64 audio channels according to the standard The inactive channels have all bits set to zero SANE Ports The device is equipped with two RJ45 200MBit SANE Ports capable of transmitting 64 channels of synchronous audio and 100MBit Ethernet SANE 2 port is compatible with MADI over Cat protocol RS485 Auxiliary Ports The auxiliary ports provide four RS485 interfaces to establish a maximum of four half duplex or two full duplex connections between the devices A wide range of bi directional and unidirectional standards can be connected such as RS485 CAN Bus bi directional requires special firmware version or RS422 DMX MIDI unidirectional The ports automatically sense whether they
28. ng shipment OPTOCORE requires that shipments are pre paid and insured unless specifically authorized in advance We strongly advise not to use simple flight cases without rack in rack mounting Declaration of Liability Optocore accepts no liability for damage caused to other devices through operation of the DD2FR FX device Optocore is not liable for any damage caused by shipping accidents misuse abuse operation with incorrect AC voltage operation with faulty peripheral equipment or improper or careless installation of the device Neither OPTOCORE nor anyone involved in the production of the equipment shall be liable for any indirect special disciplinary consequential or incidental damages arising out of the use or inability to use this equipment even if OPTOCORE has been advised of the possibility of such damages In no event shall the liability of OPTOCORE exceed the purchase price of any defective equipment Optocore accepts no claims for compensation whatsoever e g cancellation of events DD2FR FX 24 25 rev 2 3 OFTOCOR E Shipping Contents The standard shipment of a DD2FR FX unit contains the following 1 DD2FR FX unit e 1 fibre patch cable LC LC e 2 power cables Any additionally purchased equipment such as optical wave guide cables in required lengths D Sub cables and adapters RS232 cables and international electric cables which have been supplied on your request and your purchase order cannot be listed abov
29. r amplifiers before the complete system is stable and the level meters of the OPTOCORE CONTROL software indicate a normal level Do not place this device on an unstable table tripod cart etc The device may fall causing serious damage to the device The device can be disconnected from the power supply by pulling the plug These must be freely accessible at all times The device should be disconnected during lightning storms or when unused for long periods of time The device must be grounded any disconnection of the grounding is not permitted The internal components of the switched mode power supplies operate at very high voltages Coming into contact with them can lead to considerable electric shock which may result in death Only use attachments specified by the manufacturer This device contains no user serviceable parts only refer to authorized qualified service personnel for any servicing Your warranty will be voided if you tamper with the internal components DD2FR FX 3 25 rev 2 3 OT TOCOTSE Purchaser Information e Operating Manual Please read this manual If you call for technical support we will assume that you have already done so Study the operating manual carefully in order to familiarise yourself with the device and its operation The operating manual contains important information on proper use of the device It cannot be guaranteed that this operating manual will not contain typographical mistakes or
30. rranty will be void if you tamper with internal components Please address any questions or inquiries to OPTOCORE or your distributor dealer For a full warranty conditions refer to the Warranty Card attached to every Optocore device with a first shipment How to Obtain Warranty Service When discovering a problem with an OPTOCORE device you should contact either Optocore directly or a dealer distributor to determine and confirm a hardware fault If it is a software issue the hardware must not be returned to OPTOCORE OPTOCORE will issue a support ticket in this case If hardware service is required within the warranty period take the equipment along with warranty card to the nearest authorised OPTOCORE dealer distributor The dealer distributor will make sure that the device is serviced according to the terms of warranty by OPTOCORE or an authorised service centre If the equipment needs to be returned directly to OPTOCORE first contact support optocore com OPTOCORE requires the serial number of the equipment intended for return as well as a short description of the problem If possible you should also provide us a phone number where you can be reached during regular working hours To return a defective product please contact your distributor dealer Our web site http www optocore com provides a complete list of Optocore distributors dealers Make sure the equipment being returned is packed carefully to protect it from damage duri
31. the network exactly suiting the application needs A DD2FR FX for example can transmit 128 channels to a digital console system from various Optocore devices such as DD32R FX X6R FX or V3R TP If only eight return channels from the console are required only those eight channels instead of 128 inputs can be received at the DD2FR FX and transmitted via fibre optical connection leaving the other channels to be shared with the other network devices Networks with several DD2FR FX and other Optocore devices allow the transport of a huge amount of digital signals e g 768 audio channels with a sample rate of 48 kHz 32 RS485 channels and three video channels Depending on the type of fibre optic transceiver distances from 700 m up to 120 km can be covered The dual optical interfaces with data transfer rates up to 2 Gbps are equipped with LC connectors commonly used and absolutely reliable in permanent installations For rough applications such as touring and live productions the 1U OptoCon panel with rugged and secure fibre optic connectors can be added to the rack All Optocore devices are designed and built using the latest programmable microprocessors and FPGA field DD2FR FX 10 25 rev 2 3 OFTOCOR E programmable gate array logic circuitry This allows the devices internal logic to be updated in the field ensuring a continual state of the art device Optocore devices and complete networks are configured and operated using the OPTOCOR
32. transmission of up to 128 input and 128 output digital audio channels Device can operate in sample rates up to 192 kHz sample rates above 96 kHz are available upon request Each MADI port can be adjusted by OPTOCORE CONTROL software to handle different formats according to the standards AES10 1991 AES10 2003 SC multimode optical cables shall be used at the MADI ports The device is perfectly suitable for 3 party equipment integration especially with Soundcraft Studer Lawo and SSL digital consoles Please note Fiber MADI ports on DD2FR FX are equipped with special fiber transceivers which support both singlemode and multimode connectivity Please use multimode cable in each case Redundant fibre Optocore connections can be established using the two provided SFP based LC multimode or singlemode optical LINK interfaces The dual redundant ring structure provides maximum safety in a network with an outstanding low latency It facilitates the use of the advantages of fibre optical transmission in all sorts of temporary and permanent applications especially when long distance connections and high quality audio are required The DD2FR FX enables connectivity to the SANE network via RJ45 ports It is possible to use SANE as a Cat5 based cost efficient extension to the optical core system SANE ports may be used as point to point MADI over Cat5 or as a bridge interface between SANE and OPTOCORE providing in total up to 128 input and 128 output
Download Pdf Manuals
Related Search