QT-203 User`s Manual
Contents
1. D ipp 6 8 2 11 Rotor Collar Cylinder Steel Ball 1 SET Free Avg Air Motor QT 113T30 O Ring 2 pcs 113P33 UI Sound Power EN ISO 15744 Vibration level Air Overall Net Air Speed Consumption Pressure Length Weight Hose Manufacturer Mighty Seven International Co Ltd No 70 25 Ching Quang Rd Wujih Dist Taichung City 41466 Taiwan http www mighty seven com Authorized contact to compile the technical file King Tony France 3 Rue des imprimeurs ZI R publique Nord 1 86000 POITIERS FRANCE TEL 33 5 49 30 30 90 E MAIL christian aubineau kingtony eu L wy L k are Mustrator 9 on QT 113 7 16 0 5 Uncertainty K 0 5a if a lt 5 m s or K 0 4a if a gt 5 m s Ideal system connection Oil Filter O Filter Regulator amp Lubricator Air Tool 7 oon J Shut Off Cock pa Lo Water Drain Shut Off Cock Air Tank Refrigerated Air Dryer Air Compressor Piping diameters and length requirement amp The diameter MA required for the inlet pipe Dis recommended on the specification table amp The diameter B required for the branch pipe from to should be 2 times as large as QA B 2x A amp The2. AIR TYRE BUFFER Read this manual carefully before installing operating servicing or repairing Working environment 1 2 A O Using these tools in any potentially explosive environment is strictly prohibited It is always recommended that these types of tools must be operated when standing on a solid or firm location Always use these tools in a well ventilated area Slipping stumbling and falling are the major causes of potential serious injury therefore a clean and clutter free surface in the working area before operating the tools is strongly recommended Air supply and connection requirements 1 N 3 4 The maximum recommended air pressure during operation must not exceed 90 psi 6 3bar Higher air pressure may create unsafe operating conditions for the tool and the user The compressed air should be cooled and have a water filter installed at the outlet end of the compressor Even with a water filter installed some water may still condense in the piping or hose and will enter the tool mechanism causing premature damage to the tool Therefore it is recommended to install an air filter lubricator device somewhere between the tool and the compressor Always use an air compressor of the proper capacity to operate each tool Clean the hose with a blast of compressed air before connecting the hose to the air tool This will prevent both moisture and dust inside the hose from entering the
3. diameter OC required for the primary air supply from Oto should be 3 times as large as MA C 3x A amp The length for the inlet pipe D should be less than 15 feet 4 5m Air Tyre Buffer Item No QT 113 CE f
4. tool and causing possible rust or malfunction 7 MIGHTY SEVEN EC DECLARATION OF CONFORMITY Original Language Serial Number Please refer to the tool Air Die Grinder Item No QT 113 6 3 bar 90 psi We declare under our own responsibility that the above machinery fulfils all the relevant provisions of MD Machinery Directive 2006 42 EC and its amendment and is manufactured and tested according to the following standards EN ISO 11148 9 2011 EN ISO 15744 2008 EN ISO 28927 12 2012 Declared in Taichung Taiwan Dated 2013 06 01 Sonne Chen Jonney Chen Declared by QA Manager Avrarning A 1 This tool should only be used as a hand operated tool It is powered by compressed air and is not insulated against electric shock 2 This tool is specially designed for riveting sheet metals together Any application or use of this tool other than what it is designed for is strictly prohibited 3 High sound levels may cause hearing damage Always wear hearing protection when operating this tool 4 Wearing eye face protection can reduce the danger of high speed materials being ejected from tool use 5 User must wear proper clothing Loose clothing long hair stings straps belts and jewelry should not be worn when operating this tool 6 Make sure that the all the specifications of the rivets to be used are compatible with this tool 7 Check the protection against the ejecting of rivet stem in place and is operati
5. ve 8 Make certain to stand on a solid or firm location and keep body in well balanced position while operating this tool 9 Always turn off the air supply and disconnect the air hose before changing rivet nose or making adjustments on this tool 10 Release the throttle lever to avoid danger if there is a failure of energy supply or when connecting or disconnecting the air hose 11 Prolonged use will cause user fatigue Periodic breaks are recommended for user safety 12 lt is recommended to stop operating the tool whenever the user experiences discomfort tingling or pain during use 13 Beware if the compressed air hose breaks unexpectedly or is being connected or disconnected improperly This whipping action may cause injury Part List item No aT 113 C z TNO 113 113 113 113 113 13 jat i ja 13 PO1 P02 P03 P04 P05 P06 4 a P08 Inlet Bushing O Ring 13T07 1 SET PART NO DESCRIPTION 23 QT 113P23 Spring 1 QT 113P25 O Ring QT 113P26 O Ring 13T28 O Ring 2 pcs 1S zm E QT 113P27 Valve Screw 1 E 13T09 Rotor Blade 4 pcs 1 SET QT 113P29 Throttle Valve 1 aja pa g E 13 13P11 13P12 13P13 13P14 13P15 13 13 113T18 113T19 113P20 ajo 1 1 rig a 7e irei irei leei krei irel irel irei iei ie m aja ps TE olo mpa 1 l A Ea Bi a paea ae U D 2 zei izel izel izo Hh U f
Download Pdf Manuals
Related Search