CP5-Series User Manual - American Weigh Scales
Contents
1. TR Series User Manual x TR 100 100g x 0 01g TR 600 600g x 0 1g Copyright 2010 Fast Weigh Scales All rights reserved Rev 2 0 TR Series Thank you for purchasing the Fast Weigh MS 600 digital pocket scale Please read all operating instructions carefully before use Scales are precision measuring devices and should always be handled with proper care To ensure years of reliable service keep these simple tips in mind xi Do not exceed the scale s maximum capacity Overloading your scale can permanently damage it Avoid exposure to extreme heat or cold Scales perform best at normal room temperature If temperatures have changed dramatically calibration and adjustment may be necessary Allow your scale to warm up for 30 60 seconds before performing calibration and adjustment if available Store your scale in a clean dry location Dust dirt and moisture can accumulate on the weighing sensors and electronics causing inaccuracy or malfunction Avoid using your scale in close proximity to strong radio wave emitting devices such as computers cash registers and cordless phones Always weigh on a flat and level surface free from vibrations and drafts The corner of a room is usually the most stable Gently apply all items to be weighed Do not drop items onto the weighing platform Avoid dropping your scale The warranty does not cover damage due to rough treatment or overload Ch2. 1g 21 160z x 0 0010z 19 290zt x 0 001ozt 385 8dwt x 0 1dwt
3. gt oz ounce gt ozt troy ounce dwt pennyweight VI Using the Tare Feature You can use this scale s tare feature to subtract the weight of an empty container or vessel for net weight determination NOTE The weight of the container will subtract from the available capacity 1 Place the empty container or vessel on the weighing platform 2 Tap the 0 key once The display will then reset to zero If the container is removed it s weight will be displayed as a negative number 3 You may now fill the container with the quantity to be weighed The display will show the net weight of the contents 4 To return to normal weight display gross weight remove any items from the weighing platform and tap the 0 key again to re zero the scale VII Calibration Calibration and adjustment are performed at the factory However the weighing range can shift slightly during shipping Also due to changes in local acceleration of gravity around the world adjustment is recommended when moving the scale from one location to another To check calibration 1 Place the required calibration weight on the scale and note the displayed value 2 Ifthe displayed value is not within acceptable tolerance see chart below adjustment is required Model Acceptable Calibration Recommended Tolerance Weight Accuracy Class TR 100 0 03g 100g OIML M2 TR 600 0 2g 500g OIML M2 Vill Adjustment 1 Turn
4. the scale ON 2 Press and hold the M key until the display shows CAL 3 Press M again The display will flash CAL followed by the required calibration weight see above 4 Place the required calibration weight on the platform 5 The display will show PASS then return to normal weighing Calibration is complete TR Series IX Troubleshooting Problem Scale will not turn on Solution Check the batteries Problem Displayed weight fluctuates randomly Solution Make sure your workspace is stable and free of any air currents or vibration Problem Displayed weight is inaccurate Solution Perform a calibration adjustment X Error Codes 1 OUTZ Zero range has shifted Perform calibration adjustment If the problem persists the load cell may be permanently damaged due to overloading UNST Scale is unstable Use in a more stable position HHHHH Maximum capacity exceeded Remove the extra weight to avoid damaging the load cell L Batteries are low Replace the batteries XI Specifications TR 100 TR 600 Max Capacity 100g 600g Readability 0 01g 0 1g Min Weight 0 03g 0 2g 2 x AAA Alkaline Batteries Dimensions 0 8 x 2 4 x 3 8 Platform Dimensions 2 0 x 2 3 Warranty 5 Year Limited Warranty XII Capacity Readability Charts TR 100 100g x 0 01g 3 5270z x 0 0010z 500ct x 0 05ct 1543 2gn x 0 2gn TR 600 600g x 0
5. eck the batteries first if you are having any trouble with your scale This simple step can remedy most scale issues Do not disassemble your scale This product contains no user serviceable parts I Part List 1 Scale 2 Cover Weighing Tray 3 AAA Batteries x2 Il Key Description O O Weight Indicator co ON OFF Tare Key 40 M De lll Battery Installation 1 Before using the scale for the first time check the battery compartment and remove any plastic insulation strips or packaging thai may be in place to prevent battery drainage during shipping storage 2 If you are replacing the bal eries make sure the positive and negative contacts are properly aligned TR Series IV Operation 1 Place the scale on a flat level surface and press the 0 key to turn the scale on 2 Once the start up process completes and the scale goes to zero you are ready to weigh 3 Place the quantity to be weighed onto the weighing platform 4 Wait a couple seconds for the display to stabilize before taking a weight reading 5 To turn the scale off press and hold the O key V Changing the Unit of Measure 1 Press the M key to change the scales displayed unit of measure 2 Ifthe scale is turned off then back on it will default to the last unit used TR 100 Units g gram oz ounce gt ct carat gt gn grain TR 600 Units g gram
Download Pdf Manuals
Related Search