G310 Data Sheet/Manual PDF
Contents
1. 4 11 725 297 8 6 125 155 6 la 9 188 04 8 rr 4 8 400 213 4 han 2 975 75 6 8 925 ra Ld 226 7 L All tolerances 0 010 0 25 mm ALL NONINCENDIVE CIRCUITS MUST BE WIRED USING DIVISION 2 WIRING METHODS AS SPECIFIED IN ARTICLE 501 4 b 502 4 b AND 503 3 b OF THE NATIONAL ELECTRICAL CODE NFPA 70 FOR INSTALLATION WITHIN THE UNITED STATES OR AS SPECIFIED IN SECTION 19 152 OF CANADIAN ELECTRICAL CODE FOR INSTALLATION IN CANADA CONNECTING TO EARTH GROUND The protective conductor terminal is bonded to conductive UN a parts of the equipment for safety purposes and must be connected to an external protective earthing system Each G310 has a chassis ground terminal on the back of the unit Your unit should be connected to earth ground protective earth The chassis ground is not connected to signal common of the unit Maintaining isolation between earth ground and signal common is not required to operate your unit But other equipment connected to this unit may require isolation between signal common and earth ground 7o maintain isolation between signal common and earth ground care must be taken when connections are made to the unit For example a power supply with isolation between its signal common and earth ground must be used Also plugging in a USB cable may connect signal common and earth ground 1 USB s s2. DR DRxxxxxx BNL20000 G3BR10CO G3BR10S0 G3FILM10 Replacement Battery G310C Backlight Replacement 9 G310S Backlight Replacement 9 Protective Films G3FILM Contact your Red Lion distributor or visit our website for complete selection Use this part number to purchase Crimson on CD with a printed manual USB cable and RS 232 cable Otherwise download for free from www redlion net 3 Red Lion offers RJ modular jack adapters Refer to the DR literature for complete details Battery type is lithium coin type CR2025 5 Industrial grade two million write cycles 6 For use in non hazardous locations only SPECIFICATIONS POWER REQUIREMENTS G310C 24 VDC 20 33 W maximum G310S 24 VDC 20 50 W maximum Must use Class 2 or SELV rated power supply Power connection via removable three position terminal block Notes 1 The front panel PWR LED indicates power 2 The G310 circuit common is not connected to the enclosure of the unit See Connecting to Earth Ground in the section Installing and Powering the G310 2 BATTERY Lithium coin cell Typical lifetime of 10 years 3 LCD MODULE DISPLAYS MODEL G310C G310S COLORS 256 VGA 256 VGA PIXELS 640 X 480 640 X 480 BRIGHTNESS 450 cd m 850 cd m BACKLIGHT 50 000 HR TYP 20 000 HR TYP Lifetime at room temperature Refer to Display in the Software Unit Operation section 4 8 KEY KEYPAD
3. TxA RJ45 A B 5 TxEN 0C V GND Note All Red Lion devices connect A to A and B to B except for Paradigm devices Refer to www redlion net for additional information Examples of RS485 2 Wire Connections G3 to Red Lion RJ11 CBLRLCOO DLC IAMS ITMS PAXCDC4C Connections G3 RJ45 RLC RJ11 2 3 5 4 G3 to Modular Controller CBLRLCO5 Connections Name Modular Controller Name TxEN TxEN TxB 1 4 TxB RxB 41 RxB TxB 7 TxB 8 f a T CELO i 3 8 SOFTWARE UNIT OPERATION CRIMSON SOFTWARE Crimson software is available as a free download from Red Lion s website or it can be purchased on a CD see Ordering Information for part number The latest version of the software is always available from the website and updating your copy is free DISPLAY This operator interface uses a liquid crystal display LCD for displaying text and graphics The display utilizes a cold cathode fluorescent tube CCFL for lighting the display The CCFL tubes can be dimmed for low light conditions These CCFL tubes have a limited lifetime Backlight lifetime is based upon the amount of time the display is turned on at full intensity Turning the backlight off when the display is not in use can extend the lifetime of your backlight This can be accomplished through the Crimson software when configuring your unit BACKLIGHT REPLA
4. for on screen menus 5 TOUCHSCREEN Resistive analog 6 MEMORY On Board User Memory 8 Mbyte of onboard non volatile Flash memory Memory Card CompactFlash Type II slot for Type I and Type IL CompactFlash cards 7 COMMUNICATIONS USB Port Adheres to USB specification 1 1 Device only using Type B connection WARNING DO NOT CONNECT OR DISCONNECT CABLES WHILE POWER IS APPLIED UNLESS AREA IS KNOWN TO BE NON HAZARDOUS USB PORT IS FOR SYSTEM SET UP AND DIAGNOSTICS AND IS NOT INTENDED FOR PERMANENT CONNECTION Serial Ports Format and Baud Rates for each port are individually software programmable up to 115 200 baud PGM Port RS232 port via RJ12 COMMS Ports RS422 485 port via RJ45 and RS232 port via RJ12 DH485 TXEN Transmit enable open collector Voy 15 VDC Vor 0 5 V 25 mA max Note For additional information on the communications or signal common and connections to earth ground please see the Connecting to Earth Ground in the section Installing and Powering the G310 Ethernet Port 10 BASE T 100 BASE TX RJ45 jack is wired as a NIC Network Interface Card 8 ENVIRONMENTAL CONDITIONS Operating Temperature Range 0 to 50 C Storage Temperature Range G310C 20 to 70 C G310S 20 to 60 C Operating and Storage Humidity 80 maximum relative humidity non condensing from 0 to 50 C DIMENSIONS In inches mm 2 2 55 12 83 325 8 Vibration According to IEC 68 2 6 10 to 55 Hz in X Y
5. Crimson literature for more information on the proper names and locations of the files CABLES AND DRIVERS Red Lion has a wide range of cables and drivers for use with many different communication types A list of these drivers and cables along with pin outs is available from Red Lion s website New cables and drivers are added on a regular basis If making your own cable refer to the G310 Port Pin Outs for wiring information USB DATA TRANSFERS FROM THE COMPACTFLASH CARD WARNING DO NOT CONNECT OR DISCONNECT CABLES WHILE POWER IS APPLIED UNLESS AREA IS KNOWN TO BE NON HAZARDOUS USB PORT IS FOR SYSTEM SET UP AND DIAGNOSTICS AND IS NOT INTENDED FOR PERMANENT CONNECTION In order to transfer data from the CompactFlash card via the USB port a driver must be installed on your computer This driver is installed with Crimson and is located in the folder C Program Files Red Lion Controls Crimson 2 0 Device after Crimson is installed This may have already been accomplished if your G310 was configured using the USB port Once the driver is installed connect the G310 to your PC with a USB cable and follow Mounting the CompactFlash instructions in the Crimson 2 user manual ETHERNET COMMUNICATIONS Ethernet communications can be established at either 10 BASE T or 100 BASE TX The G310 unit s RJ45 jack is wired as a NIC Network Interface and a bi color green amber LED in the upper left The LEDs represent the Card Fo
6. intervals Later Microsoft operating systems will not lock the drive unless they need to write data Windows 98 may lock the drive any time it is mounted thereby interfering with logging Refer to Mounting the CompactFlash in the Crimson 2 User Manual KEYPAD The G310 keypad consists of eight keys for on screen menus TOUCHSCREEN This operator interface utilizes a resistive analog touchscreen for user input The unit will only produce an audible tone beep when a touch on an active touchscreen cell in sensed The touchscreen is fully functional as soon as the operator interface is initialized and can be operated with gloved hands TROUBLESHOOTING YOUR G310 If for any reason you have trouble operating connecting or simply have questions concerning your new G310 contact Red Lion s technical support For contact information refer to the back page of this bulletin for phone and fax numbers EMAIL techsupport redlion net Web Site http www redlion net BATTERY amp TIME KEEPING G310C WARNING EXPLOSION HAZARD THE AREA MUST BE KNOWN TO BE NON HAZARDOUS BEFORE SERVICING REPLACING THE UNIT AND BEFORE INSTALLING OR REMOVING I O WIRING AND BATTERY WARNING EXPLOSION HAZARD DO NOT DISCONNECT EQUIPMENT UNLESS POWER HAS BEEN DISCONNECTED AND THE AREA IS KNOWN TO BE NON HAZARDOUS A battery is used to keep time when the unit is without power Typical accuracy of the G310 time keeping is less than one minut
7. mmoaommao g X zz zzzz eesssQqg g 55 5566 NtTGND 652 gt gt vv O odmdrmiuoas E NN uuu myg ME JA oorr Du 4 AdO ux agregar SSS kk kli YN 66 OOOO X Application Dependent Ld LILI ram iu oo CBLPROGO can also be used to communicate with either a PC or an ICM5 DB9 adapter not included 1 foot long 3 DB9 adapter not included 10 feet long OO OL NI DM om A w hy G310 PORT PIN OUTS PROTECTIVE EARTH GROUND TxA PIN 8 RTS PIN 6 RTS PIN 6 TxA RxA RxB TxEN COMM TxB COMM COMM Tx Rx COMM COMM Tx eTxB PIN 1 Rx CTS PIN 1 eCTS PIN 1 COMMON 1 1 1 X o N T gt N N ETHERNET NIC RS485 R RS232 POWER COMMS COMMS PGM PORT CONNECTOR PORT PORT 1 e N CQ N RS422 485 COMMS PORT The G310 has one RS422 485 port This port can be configured to act as either RS422 or RS485 RS485 2 WIRE CONNECTIONS 5V 7 TxB 1 RS422 485 4 WIRE CONNECTIONS 5V 130K 7 DH485 COMMUNICATIONS The G310 s RS422 485 COMMS port can also be used for Allen Bradley DH485 communications WARNING DO NOT use a standard DH485 cable to connect this port to Allen Bradley equipment A cable and wiring diagram are available from Red Lion G3 to AB SLC 500 CBLAB003 Connections TxEN 0C MES 130K 130K i 8 TxA 2 RJ45 RLC 1 2 Name TxB
8. power supply due to single faults SELV is an acronym for safety extra low voltage Safety extra low voltage circuits shall exhibit voltages safe to touch both under normal operating conditions and after a single fault such as a breakdown of a layer of basic insulation or after the failure of a single component has occurred COMMUNICATING WITH THE G310 CONFIGURING A G310 The G310 is configured using Crimson software Crimson is available as a free download from Red Lion s website or it can be purchased on CD Updates to Crimson for new features and drivers are posted on the website as they become available By configuring the G310 using the latest version of Crimson you are assured that your unit has the most up to date feature set Crimson software can configure the G310 through the RS232 PGM port USB port or CompactFlash The USB port is connected using a standard USB cable with a Type B connector The driver needed to use the USB port will be installed with Crimson If this driver has not been installed it can be downloaded from the website The RS232 PGM port uses a programming cable made by Red Lion to connect to the DB9 COM port of your computer If you choose to make your own cable use the G310 Port Pin Out Diagram for wiring information The CompactFlash can be used to program a G3 by placing a configuration file and firmware on the CompactFlash card The card is then inserted into the target G3 and powered Refer to the
9. waste regulations Also the battery must not be disposed of in fire or in a manner whereby it may be damaged and its contents come into contact with human skin The battery used by the G310 is a lithium type CR2025 OPTIONAL FEATURES AND ACCESSORIES INDOOR VERSUS OUTDOOR Red Lion offers two versions of its G310 unit The G310C000 uses an overlay with a textured finish and keys that are embossed This overlay is not rated for outdoor use The G310S000 uses an overlay with a glossy finish that uses UV rated material for outdoor use The keys on this overlay are not embossed The display is significantly brighter than the G310C000 COMPACTFLASH SOCKET CompactFlash socket is a Type II socket that can accept either Type I or II cards Use cards with a minimum of 4 Mbytes and a maximum of 2 Gbytes with the G310 s CompactFlash socket Cards are available at most computer and office supply retailers CompactFlash can be used for configuration transfers larger configurations data logging and trending OPTIONAL COMMUNICATION CARD Red Lion offers optional communication cards for fieldbus communications These communication cards will allow your G310 to communicate with many of the popular fieldbus protocols Red Lion is also offering a communications card for additional RS232 and RS422 485 communications Visit Red Lion s website for information and availability of these cards Note Do not remove or insert the CompactFlash card
10. while power is applied Refer to Front Panel LEDs CUSTOM LOGO Each G3 operator interface has an embossed area containing the Red Lion logo Red Lion can provide custom logos to apply to this area Contact your distributor for additional information and pricing CompactFlash Insert Face Up A n N pBGBI 13 l Information stored on a CompactFlash card by a G310 can be read by a card reader attached to a PC This information is stored in IBM Windows PC compatible FAT 16 file format FRONT OVERLAY NOTE For reliable operation in all of our products Red Lion recommends the use of SanDisk and SimpleTech brands of CompactFlash cards Industrial grade versions that provide up to two million write erase cycles minimum are available from Red Lion LIMITED WARRANTY The Company warrants the products it manufactures against defects in materials and workmanship for a period limited to two years from the date of shipment provided the products have been stored handled installed and used under proper conditions The Company s liability under this limited warranty shall extend only to the repair or replacement of a defective product at The Company s option The Company disclaims all liability for any affirmation promise or representation with respect to the products The customer agrees to hold Red Lion Controls harmless from defend and indemnify RLC against damages claims and expenses arising out o
11. CEMENT CAUTION Backlight is not field replaceable for hazardous location applications Unit must be returned to Red Lion Controls for repair The backlight assembly is field replaceable in non hazardous locations only Refer to the instructions included in the appropriate backlight replacement kit FRONT PANEL LEDS There are three front panel LEDs Shown below is the default status of the LEDs INDICATION RED TOP LABELED PWR FLASHING STEADY Unit is powered and running an application YELLOW MIDDLE OFF No CompactFlash card is present STEADY FLASHING RAPIDLY Unit is in the boot loader no valid configuration is loaded 1 Valid CompactFlash card present CompactFlash card being checked Unit is writing to the CompactFlash either because it is storing FLICKERING data or because the PC connected via the USB port has locked the drive 2 FLASHING SLOWLY GREEN BOTTOM FLASHING STEADY Incorrectly formatted CompactFlash card present A tag is in an alarm state Valid configuration is loaded and there are no alarms present 1 The operator interface is shipped without a configuration After downloading a configuration if the light remains in the flashing state continuously try cycling power If the LED still continues to flash try downloading a configuration again 2 Do not turn off power to the unit while this light is flickering The unit writes data in two minute
12. Z direction for 1 5 hours 1 g Shock According to IEC 68 2 27 Operational 30 g 9 msec in 3 directions Altitude Up to 2000 meters CERTIFICATIONS AND COMPLIANCES SAFETY UL Recognized Component File E179259 UL61010 1 CSA 22 2 No 61010 1 Recognized to U S and Canadian requirements under the Component Recognition Program of Underwriters Laboratories Inc UL Listed File E211967 UL61010 1 UL1604 CSA 22 2 No 61010 1 CSA 22 2 No 213 M1987 LISTED by Und Lab Inc to U S and Canadian safety standards Type 4X Enclosure rating Face only UL50 IECEE CB Scheme Test Certificate ZUS 9737C UL CB Scheme Test Report E179259 V01 S04 Issued by Underwriters Laboratories Inc IEC 61010 1 EN 61010 1 Safety requirements for electrical equipment for measurement control and laboratory use Part 1 IP66 Enclosure rating Face only IEC 529 ELECTROMAGNETIC COMPATIBILITY Emissions and Immunity to EN 61326 Electrical Equipment for Measurement Control and Laboratory use o Immunity to Industrial Locations Electrostatic discharge EN 61000 4 2 Criterion A 4 kV contact discharge 8 kV air discharge Electromagnetic RF fields EN 61000 4 3 Criterion A 10 V m Fast transients burst EN 61000 4 4 Criterion A 2 kV power 2 kV signal Surge EN 61000 4 5 Criterion A 1 kV L L 2 kV L amp N E power RF conducted interference EN 61000 4 6 Criterion B 3 V rms Emissions Emissions EN 55011 Class A Notes 1 Criterion A Normal operation with
13. e per month drift The battery of a G310 unit does not affect the unit s memory all configurations and data is stored in non volatile memory CAUTION RISK OF ELECTRIC SHOCK The inverter board attached to the mounting plate supplies the high voltage to operate the backlight Touching the inverter board may result in injury to personnel components Before handling the operator interface without the rear cover attached discharge static charges from your body by touching a grounded bare metal object Ideally handle the operator interface at a static controlled clean workstation Also do not touch the surface areas of the circuit board Dirt oil or other contaminants may adversely affect circuit operation f CAUTION The circuit board contains static sensitive To change the battery of a G310 remove power cabling and then the rear G310S cover of the unit To remove the cover remove the five screws designated by the arrows on the rear of the unit Then by lifting the top side hinge the cover thus providing clearance for the connectors on the bottom side of the PCB as shown in the illustration below Install in the reverse manner Remove the old battery from the holder and replace with the new battery Replace the rear cover cables and re apply power Using Crimson or the unit s keypad enter the correct time and date Please note that the old battery must be disposed of in a manner that complies with your local
14. f subsequent sales of RLC products or products containing components manufactured by RLC and based upon personal injuries deaths property damage lost profits and other matters which Buyer its employees or sub contractors are or may be to any extent liable including without limitation penalties imposed by the Consumer Product Safety Act P L 92 573 and liability imposed upon any person pursuant to the Magnuson Moss Warranty Act P L 93 637 as now in effect or as amended hereafter No warranties expressed or implied are created with respect to The Company s products except those expressly contained herein The Customer acknowledges the disclaimers and limitations contained herein and relies on no other warranties or affirmations Red Lion Controls AP Unit 101 XinAn Plaza Building 13 No 99 Tianzhou Road ShangHai P R China 200223 Tel 86 21 6113 3688 Fax 86 21 6113 3683 Red Lion Controls BV Printerweg 10 NL 3821 AD Amersfoort Tel 31 0 334 723 225 Fax 31 0 334 893 793 Red Lion Controls 20 Willow Springs Circle York PA 17406 Tel 1 717 767 6511 Fax 1 717 764 0839
15. hield may be connected to earth ground at the host USB s shield in turn may also be connected to signal common POWER SUPPLY REQUIREMENTS The G310C requires a 24 VDC power supply rated at 33 W and the G310S requires a 24 VDC power supply rated at 50 W Your unit may draw considerably less the rated power depending upon the options being used As additional features are used your unit will draw increasing amounts of power Items that could cause increases in current are additional communications optional communications card CompactFlash card and other features programmed through Crimson In any case it is very important that the power supply is mounted correctly if the unit is to operate reliably Please take care to observe the following points The power supply must be mounted close to the unit with usually not more than 6 feet 1 8 m of cable between the supply and the operator interface Ideally the shortest length possible should be used The wire used to connect the operator interface s power supply should be at least 22 gage wire If a longer cable run is used a heavier gage wire should be used The routing of the cable should be kept away from large contactors inverters and other devices which may generate significant electrical noise A power supply with a Class 2 or SELV rating is to be used A Class 2 or SELV power supply provides isolation to accessible circuits from hazardous voltage levels generated by a mains
16. in specified limits 2 Criterion B Temporary loss of performance from which the unit self recovers 0 CONNECTIONS Compression cage clamp terminal block Wire Gage 12 30 AWG copper wire Torque 5 7 inch pounds 56 79 N cm 1 CONSTRUCTION Steel rear metal enclosure with NEMA 4X IP66 aluminum front plate when correctly fitted with the gasket provided Installation Category II Pollution Degree 2 2 MOUNTING REQUIREMENTS Maximum panel thickness is 0 25 6 3 mm For NEMA 4X IP66 sealing a steel panel with a minimum thickness of 0 125 3 17 mm is recommended Maximum Mounting Stud Torque 17 inch pounds 1 92 N m 3 WEIGHT 5 53 Ibs 2 51 Kg I 11 55 293 3 4 o o o NSTALLING AND POWERING THE G310 MOUNTING INSTRUCTIONS This operator interface is designed for through panel mounting A panel cut out diagram and a template are provided Care should be taken to remove any loose material from the mounting cut out to prevent that material from falling into the operator interface during installation A gasket is provided to enable sealing to NEMA 4X IP66 specification Install the 14 kep nuts provided and tighten evenly for uniform gasket compression Note Tightening the kep nuts beyond a maximum of 17 inch pounds 1 92 N m may cause damage to the front panel 12 250 311 2
17. nter data through the touchscreen or front panel 8 button keypad SAFETY SUMMARY All safety related regulations local codes and instructions that appear in the manual or on equipment must be observed to ensure personal safety and to prevent damage to either the instrument or equipment connected to it If equipment is used in a manner not specified by the manufacturer the protection provided by the equipment may be impaired Do not use the controller to directly command motors valves or other actuators not equipped with safeguards To do so can be potentially harmful to persons or equipment in the event of a fault to the controller AN QD A The protective conductor terminal is bonded to conductive parts of the equipment for safety purposes and must be connected to an external protective earthing system WARNING EXPLOSION HAZARD SUBSTITUTION OF COMPONENTS MAY IMPAIR SUITABILITY FOR CLASS DIVISION 2 CLASS II DIVISION 2 CLASS III DIVISION 2 A CAUTION Risk of electric shock A CAUTION Risk Of Danger Read complete instructions prior to installation and operation of the unit CompactFlash is a registered trademark of CompactFlash Association VGA DISPLAY AND TOUCHSCREEN Configured using Crimson software version 2 0 or later Up to 5 RS 232 422 485 communications ports 2 RS 232 and 1 RS 422 485 on board 1 RS 232 and 1 RS422 485 on optional communications card 10 Base T 100 Base TX Ethernet Port t
18. o network units and host web pages USB Port to download the unit s configuration from a PC or for data transfers to a PC Unit s configuration is stored in non volatile memory 8Mbyte Flash CompactFlash Socket to increase memory capacity 10 4 inch TFT 256 Color VGA 640x480 pixel LCD Sunlight Visible Outdoor Unit with UV rated overlay available Ce 8 button keypad for on screen menus Three front panel LEDs Power unit from 24VDC 20 supply Resistive Analog Touchscreen CONTENTS OF PACKAGE G310 Operator Interface Panel Gasket This hardware bulletin Template for panel cutout Hardware packet for mounting unit into panel Terminal block for connecting power ORDERING INFORMATION DESCRIPTION PART NUMBER Operator Interface for indoor applications only textured finish with embossed keys G310C000 Operator Interface for indoor or outdoor applications glossy finish with UV rated overlay keys are not embossed 64 MB CompactFlash Card 5 256 MB CompactFlash Card 5 512 MB CompactFlash Card 5 RS 232 485 Optional Communication Card CANopen Optional Communication Card Profibus DP Optional Communication Card G310S000 G3CF064M G3CF256M G3CF512M G3RS0000 G3CNO0000 G3PBDP00 SFCRM200 CBLPROGO CBLUSBOO CBLoxxx G3CF G3RS G3CN G3PBDP SFCRM2 Crimson RS 232 Programming Cable USB Cable Communications Cables 1 DIN Rail Mountable Adapter Products CBL
19. r example when wiring to a hub or switch use a straight through cable following statuses but when connecting to another NIC use a crossover cable YELLOW solid Link established YELLOW flashing Data being transferred The Ethernet connector contains two LEDs A yellow LED in the upper right GREEN 10 BASE T Communications AMBER 100 BASE TX Communications The Crimson manual contains additional information on Ethernet communications CONNECTING A G310 OPERATOR RS232 PORTS INTERFACE TO AN ICM5 The G310 has two RS232 ports There is the PGM port and the COMMS port LJ MEN Although only one of these ports can be used for programming both ports can be used for communications with a PLC O gt The RS232 PGM port can be used for either master or slave protocols with g any G310 configuration gt Examples of RS232 communications could involve another Red Lion product 9 or a PC By using a cable with RJ12 ends on it and a twist in the cable RS232 gr communications with another G3 product or the Modular Controller can be cH established Red Lion part numbers for cables with a twist in them are pm CBLPROGO CBLPROGO CBLRLCOI or CBLRCO2 3 m G3 RS232 to a PC ICMS5 DIP Switch Settings Eee oed e LH G3 RJ12 ON AMY NORDHO nMYNOR S9598525ygua8 o99ppuH 25252525525rr vooz rtoo 2222446 zzp Y O000
20. red lion Tel 1 717 767 6511 Fax 1 717 764 0839 www redlion net Bulletin No G310 J Drawing No LP0581 Released 1 08 MODEL G310 GRAPHIC LCD OPERATOR INTERFACE TERMINAL WITH TANK NAME E m O m O a a a FOR USE IN HAZARDOUS LOCATIONS Class I Division 2 Groups A B C and D Class II Division 2 Groups F and G Class III Division 2 C US LISTED 63YN LABORATORY EQUIPMENT GENERAL DESCRIPTION The G310 Operator Interface Terminal combines unique capabilities normally expected from high end units with a very affordable price It is built around a high performance core with integrated functionality This core allows the G310 to perform many of the normal features of the Paradigm range of Operator Interfaces while improving and adding new features The G310 is able to communicate with many different types of hardware using high speed RS232 422 485 communications ports and Ethernet 10 Base T 100 Base TX communications In addition the G310 features USB for fast downloads of configuration files and access to trending and data logging A CompactFlash socket is provided so that Flash cards can be used to collect your trending and data logging information as well as to store larger configuration files In addition to accessing and controlling of external resources the G310 allows a user to easily view and enter information A sunlight visible outdoor version is available for direct sunlight applications Users can e
Download Pdf Manuals
Related Search