Artisan Technology Group is your source for quality new and
Contents
1. A rtisan Artisan Technology Group is your source for quality Technology Group new and certified used pre owned equipment FAST SHIPPING AND SERVICE CENTER REPAIRS WE BUY USED EQUIPMENT DELIVERY Experienced engineers and technicians on staff Sell your excess underutilized and idle used equipment TENS OF THOUSANDS OF at our full service in house repair center We also offer credit for buy backs and trade ins IN STOCK ITEMS www artisantg com WeBuyEquipment 7 EQUIPMENT DEMOS HUNDREDS OF InstraV ea REMOTE INSPECTION LOOKING FOR MORE INFORMATION MANUFACTURERS Remotely inspect equipment before purchasing with Visit us on the web at www artisantg com 7 for more our interactive website at www instraview com information on price quotations drivers technical LEASING MONTHLY specifications manuals and documentation RENTALS ITAR CERTIFIED CEP BAD tia Contact us 888 88 SOURCE sales artisantg com www artisantg com M 68735 GY Nevvport Oriel Product line 150 Long Beach Boulevard Stratford CT 06497 Phone 203 377 8282 800 714 5393 Fax 203 378 2457 E MAIL oriel sales newport com DC REGULATED POWER SUPPLY MODEL 68735 USER MANUAL Please read these instructions completely before operating this equipment The specification and operating instructions apply only to the model s covered by this manual If there are any questions or problems regarding the use of this equipment please contact New2. ates power is applied to the unit Toggle switch Used to apply power to the unit Power supply output terminals The top terminal 1 is the positive output The lower terminal 2 is the negative output AC Input fused and voltage selectable for 120 240 operation Socket is an IEC style socket See Section IV for voltage and fusing selection 4A for 120 Volt operation 2A for 240 Volt operation Used for cooling internal components Artisan Technology Group Quality Instrumentation Guaranteed 888 88 SOURCE www artisantg com M 68735 DC REGULATED POWER SUPPLY IV SET UP AND USE Because this power supply is capable of generating more power than the 100 watts and lower rated lamps can handle care must be exercised prior to turning on the power supply with the lamp attached 1 Voltage selector card Indicator pin Figure 1 Power Input Connector Prior to plugging in the AC power cord verify that the correct mains voltage is selected The selection is indicated by the white pin on the power entry module For 95 130 VAC operation use the 120V position and for 95 130 VAC operation use the 120V position and for 190 260 VAC use the 240V position Re configuring the Power Input Module The power entry module mounted on the rear panel provides an international IEC receptacle for power cord attachment It has 120 240 VAC selection capability and the facility for North American and European fusing config
3. e defective goods are returned freight prepaid to a Newport designated facility If goods are not returned to Newport and the user chooses to have repairs made at their premises Newport shall provide labor for field adjustment repair and or replacement at prevailing rates for field service on a portal to portal basis Newport shall be relieved of all obligations and liability under this warranty of 1 The user operates the device with any accessory equipment or part not specifically approved or manufactured or specified by Newport unless buyer furnishes reasonable evidence that such installations were not the cause of the defect This provision shall not apply to any accessory equipment or part which does not affect the safe operation of the device 2 The goods are not operated or maintained in accordance with Newport s_ instructions and specifications 3 The goods have been repaired altered or modified by other than authorized Newport personnel 4 Buyer does not return the defective goods freight prepaid to a Newport facility within the applicable warranty period IT IS EXPRESSLY AGREED THAT THIS WARRANTY SHALL REPLACE ALL WARRANTIES OF FITNESS AND MERCHANTABILITY BUYER HEREBY WAIVES ALL OTHER WARRANTIES GUARANTEES CONDITIONS OR LIABILITIES EXPRESSED OR IMPLIED ARRISING BY LAW OR OTHERWISE WHETHER OR NOT OCCASIONED BY NEWPORT S NEGLIGENCE This warranty shall not be extended altered or varied except by a w
4. ned without a RMA may be rejected by the Newport Receiving Department Equipment returned under warranty will be returned with no charge for the repair or shipping Newport will notify you of any repairs not covered by the warranty with the cost of the repair before starting the work Please return equipment in the original or equivalent packaging You will be responsible for damage incurred from inadequate packaging ifthe original packaging is not used Include the cables connector caps and antistatic materials sent and or used with the equipment so that Newport can verify correct operation of these accessories Artisan Technology Group Quality Instrumentation Guaranteed 888 88 SOURCE www artisantg com A rtisan Artisan Technology Group is your source for quality Technology Group new and certified used pre owned equipment FAST SHIPPING AND SERVICE CENTER REPAIRS WE BUY USED EQUIPMENT DELIVERY Experienced engineers and technicians on staff Sell your excess underutilized and idle used equipment TENS OF THOUSANDS OF at our full service in house repair center We also offer credit for buy backs and trade ins IN STOCK ITEMS www artisantg com WeBuyEquipment 7 EQUIPMENT DEMOS HUNDREDS OF InstraV ea REMOTE INSPECTION LOOKING FOR MORE INFORMATION MANUFACTURERS Remotely inspect equipment before purchasing with Visit us on the web at www artisantg com 7 for more our interactive website at www instraview com i
5. nformation on price quotations drivers technical LEASING MONTHLY specifications manuals and documentation RENTALS ITAR CERTIFIED CEP BAD tia Contact us 888 88 SOURCE sales artisantg com www artisantg com
6. port or the representative from whom this equipment was purchased Artisan Technology Group Quality Instrumentation Guaranteed 888 88 SOURCE www artisantg com M 68735 DC REGULATED POWER SUPPLY TABLE OF CONTENTS INTRODUCTION eluinntinn aai aroa a aae a aa a aa a a AEE ein aera 1 I SPEGIFICATION Suit A Ata 2 Il CONTROLS AND FUNCTIONS ccoccocicccoccconoconononononnnnrnnnrrnrnr rr rr 3 Wy SETUPAND USE siria a aa cas 4 V WARRANTY AND RETURNS ccc ccoo eia i a Aia 6 Artisan Technology Group Quality Instrumentation Guaranteed 888 88 SOURCE www artisantg com M 68735 DC REGULATED POWER SUPPLY l INTRODUCTION The ORIEL Model 68735 Power Supply provides a highly stable and regulated DC source for precision radiometric applications with any of the quartz halogen lamps of 100 watts or less ratings as well as any of the other low wattage incandescent lamps with operating voltages down to 5 volts The unit also has sufficient power output to drive the Model 6363 IR source which draws 11 7 amperes at 12 volts The unit s low output ripple 0 17 RMS coupled with the slow responding mass of the lamp filaments yields light ripples of less than 04 RMS The following Oriel light sources may be operated with the Model 68735 6319 20W QTH 6V 3 3A 20 Watts nominal 6333 6359 100W QTH 12V 8 3A 100 Watts nominal 6363 140W IR ELEMENT 12V 11 7A 140 Watts nominal Note This supply is not expected to perfo
7. ranteed 888 88 SOURCE www artisantg com M 68735 DC REGULATED POWER SUPPLY 2 Disengage the Lamp Voltage control locking mechanism by turning the outer ring counter clockwise Rotate Lamp Voltage control fully counter clockwise 3 Turn on power supply 4 Rotate Voltage control knob slowly letting the soft start circuitry increase the output open circuit voltage until the required voltage is reached for the specified lamp Check the table on page 1 if you are not sure of this setting 5 Turn off power supply 6 Connect lamp cables to output terminal block 1 for positive and 2 for negative connections 7 Turn on Power Supply and wait until soft start circuitry allows output voltage to reach the required level 8 Readjust as required for exact output voltage setting and lock the knob by turning the outer ring clockwise 9 Place the Volt Amperes switch to the Amperes position and note the output current That reading multiplied by the voltage reading should not exceed the wattage rating of the lamp in use If the lamp is over driven the lamp life will be noticeably shortened 1 o If full power intensity is not required the output voltage can be reduced In most instances this will increase lamp life Once the power supply is set up for a specific lamp the above procedure can be reduced to simply turning the power supply ON and OFF The special soft start circuitry should protect the lamp at turn on Note The fron
8. ritten document signed by both parties If any portion of this agreement is invalidated the remainder of the agreement shall remain in full force and effect CONSEQUENTIAL DAMAGES Newport shall not be responsible for consequential damages resulting from misfunctions or malfunctions of the goods described in this manual Newport s total responsibility is limited to repairing or replacing the misfunctioning or malfunctioning goods under the terms and conditions of the above described warranty INSURANCE Persons receiving goods for demonstrations demo loan temporary use or in any manner in which title is not transferred from Newport shall assume full responsibility for any and all damage while in their care custody and control If damage occurs unrelated to the proper and warranted use and performance of the goods recipient of the goods accepts full responsibility for restoring the goods to their condition upon original delivery and for assuming all costs and charges RETURNS Before returning equipment to Newport for repair please call the Customer Service Department at 203 377 8282 Have your purchase order number available before calling Newport The Customer Service Representative will give you a Return Material Authorization number RMA Having an RMA will shorten the time required for repair because it ensures that your equipment will be properly processed Write the RMA on the returned equipment s box Equipment retur
9. rm with the precision of the Oriel Model No 68831 power supply however using a precision external current shunt and meter would verify amperage to the lamps Artisan Technology Group Quality Instrumentation Guaranteed 888 88 SOURCE www artisantg com M 68735 DC REGULATED POWER SUPPLY ll SPECIFICATIONS Output Voltage Output Power Output Current Circuit Format Regulation Stability Input Requirements Light Ripple Weight Dimensions 5 13 Volts DC adjustable 140 Watts maximum 12 Amperes maximum Voltage Regulation Linear Series Pass Transistor 0 4 change in light output for 10 change in line voltage within operating range 0 2 change over 8 hours after a 30 minute warm up period 95 130 VAC 190 260 VAC 50 60 Hz 04 RMS 17 3 4 lbs 8 Kg 6 1 8 15 6 cm high 12 3 8 31 4 cm wide 14 wide 35 6 cm deep Artisan Technology Group Quality Instrumentation Guaranteed 888 88 SOURCE www artisantg com M 68735 DC REGULATED POWER SUPPLY CONTROLS AND FUNCTIONS FRONT PANEL Meter switch setting Volts Amperes Switch Lamp Voltage Control voltage level Power Indicator Power Switch REAR PANEL Output Terminal Block Power Entry Connector Fuses Fan Reads output in either Volts or Amperes depending on Toggle switch Selects metering mode Ten turn potentiometer with friction lock Sets the output Amber Neon Indic
10. t panel voltmeter indicates the voltage present at the output terminals on the rear panel Dependent on the load current and type of wire used the voltage across the load will be somewhat lower If the voltage delivered to the load is critical a separate voltmeter should be connected at the load to determine its value The front panel ammeter is accurate regardless of load and wiring used Artisan Technology Group Quality Instrumentation Guaranteed 888 88 SOURCE www artisantg com M 68735 DC REGULATED POWER SUPPLY V WARRANTY AND RETURNS Newport warrants that all goods described in this manual except consumables such as lamps bulbs filters ellipses etc shall be free from defects in material and workmanship Such defects become apparent within the following period 1 All products described here except spare parts one 1 year or 3000 hours of operation whichever comes first after delivery of the goods to the buyer 2 Spare parts ninety 90 days after delivery of goods to the buyer Newport s liability under this warranty is limited to the adjustment repair and or replacement of the defective part s During the above listed warranty period Newport shall provide all materials to accomplish the repaired adjustment repair or replacement Newport shall provide the labor required during the above listed warranty period to adjust repair and or replace the defective goods at no cost to the buyer ONLY IF th
11. urations This unit has been set at the factory based on destination for either 120 VAC North American fused operation or 240 VAC European operation Note that two European fuses are installed To change the selected voltage or fuse configuration unplug the power cord from the unit and pry off the cover fuse block assembly with a small bladed screwdriver or similar tool Use the indicator pin to pull the voltage selector card straight out of the housing Orient the indicator pin so that it points in the opposite direction from the desired voltage as indicated on the card Re insert the card with the voltage indication entering the module first and the pin pointing out When the cover is replaced verify that the pin indicates the correct voltage The fuses are mounted on the inside of the cover The exposed fuse s are the active set To change the fuse configuration loosen the Phillips Head Screw which holds the fuse block by two turns Lift the fuse block up at the screw end and then slide the block away from the screw Invert the block and re assemble making sure that the end of the block opposite the screw is engaged before seating the block at the screw end and re tightening the screw For operation at 240 VAC the alternative North American fusing arrangement may be used for polarized non reversible power socket plug combinations The fuse should be rated at the 240V value Artisan Technology Group Quality Instrumentation Gua
Download Pdf Manuals
Related Search