Vulkan TU Engleska.cdr
Contents
1. CENTRAL HEATING These fireplaces are intended for heating of rooms through installation of central heating using solid fuel coal or dry wood Fireplace may be connected to installation with open or closed system for pressure maintenance with water temperature up to 90 C and max Working pressure 2 5 bars Fireplace construction enables ease heating with fuel and ash cleaning Reliable operation is provided as well as high level of energy usage and long life with adherence to the recommendations for appropriate installation and exploitation which we prove with given warranty period of 5 years All connections to the fireplace entry exit pipelines funnel pipe and etc are of standard production so they do not require special adaptation on connection Fireplace has cast grate CAUTION Fireplace door and ashtray must be closed during operation since otherwise temperature may rise uncontrollably above allowed level which may cause damage to the fireplace and installation Also this may cause unjustifiably high fuel consumption 2 SAFETY 2 1 Safety and reliability of fireplace operation These fireplaces for central heating are so constructed and made to provide maximal safety during operation on condition that users in all matters adhere to this INSTRUCTION No liability is assumed for injury of people animals or damages of property which is the consequence of failure to adhere to this instruction Any other use of fireplace i2. operating temperature IMPORTANT Do not leave product with open door unattended and ashtray must be in the position behind limiter completely closed since it may lead to uncontrolled increase of temperature above allowed level 7 TECHNICAL TROUBLESHOOTING Technical problems may occur due to following reasons a Due to possible factory based defects in such case contact the manufacturer ABC PROIZVOD b Due to defects at installation and connecting in such case contactthe technician c As the consequence of improper handling non observance of proper heating mode and fireplace maintenance by the user in such case please read again this manual and proceed properly If after all above mentioned problem persists contact the factory ABC PROIZVOD for advice intervention 8 CLEANING AND MAINTENANCE Due to longer life of fireplace and its proper operation it is necessary to properly maintain fireplace both during firing and after that Space for ash and opening for airflow below regulator flap when removed ashtray opening is located on the right hand side must be regularly cleaned Fireplace must be cleaned from time to time against grime at least once a month because grime and tar that settle during combustion on internal surfaces of the burner increase consumption of fuel and reduce utilization degree Manufacturer recommends usage of chemical agent ASTRATHERM which facilitates mechanical removal of resi
3. side Standard fireplace connection is 145 mm In case that this connection is not suitable for you our factor may offer to you in our assortment reductions which change existing condition to the following dimensions 120 130 or 150 B 480 WZ 1020 H 945 Fig 1a The lowest water temperature in fireplace i AIN button of drought regulator at number 1 455 290 gt E AU Hearth door Fig 1b The highest water temperature in fireplace 1 e sd button of drought regulator at number 9 10 4 Smoke pipe AN 5 Pressure line R1 6 Return line R1 8 6 We Connection R1 2 for safety valve X ef E Comecton R12 for thermal valve gt 10 10 Connection R1 2 for heat exchanger thermal protection Er TECHNICAL DATA VULKAN FIREPLACE Total power kW 24 Power transferred to water kW 21 Power given as radiation kW 3 Required drought Pa 10 Mass total weight kg 150 Water quantity 1 30 Max working temperature C 90 Max working pressure bar 2 5 Smoke pipe diameter mm 145 Width L mm 575 Height H mm 1015 Depth B mm 480 4 TRANSPORTATION AND STORAGE Fireplace is protected by packaging which is not resistant to atmosphere influence It should be stored in covered space Transport to user is done as under contract After you remove packaging off the fireplace check for damages during transport and ha
4. USER MANUAL FOR SOLID FUEL STOVE VOLCANO 24kW Dear customers Thank you and congratulations because with this purchase you became a member of large family of satisfied customers of ABC PROIZVOD We expect that very soon you will become aware that you chose quality and economic product which is the result of long tradition of our company in the production of boilers stoves and fireplaces for central heating In case of any doubt dilemma or question feel free to contact us regardless of the place or seller where you purchased our product and we will assist you with our professional advice and technical assistance e Yours sincerely ton Prior to the use of these fireplaces for central heating read carefully this instruction since it gives you important information regarding safe installation use and maintenance ofthese devices INSTRUCTION CONTENT 1 Purpose and specific characteristics ofthese fireplaces 2 Safety 3 Description and technical characteristics 4 Transport and storage 5 Installation 6 Operation heating 7 Technical troubleshooting 8 Cleaning and maintenance 9 Dismantling and removal 10 Annex a Compliance with EU directives b Compliance with international standards c Warranty ABC PROIZVOD d o o Srbija 31000 U ice Milo a Obrenovi a 2 381 0 31 514 502 514 501 e mail office abcproizvod rs www abcproizvod rs 1 PURPOSE AND SPECIFIC CHARACTERISTICS OF FIREPLACES FOR
5. a cev Ventil Zatvoren ekspanzioni sud Manometar Radijatorski ventil Radijator 8 Ozra ni ventil AD ARONNE 6 OPERATION FIRING 9 Cirkularna pumpa 10 Sigurnosni ventil 11 Potisni vod 12 Priklju ni vod za vodovodnu mre u 12 Odvod tople vode 13 Sonda termoventila 14 Priklju ak za punjenje i pra njenje 1 2 15 Povratni vod Solid fuel must be physically separated from the fireplace with some space and physical barrier Ashtray vessel must be made of non combustible materials and located out of the place with stored fuel 6 1 FIRST FIRING e Atthe first firing following conditions must be observed e chimney must be cleaned and properly connected to the fireplace e fireplace and heating installation must have installed all safety devices e system must be filled with water and vented e within the operating mode of the fireplace burner door must be closed and ashtray positioned into the position behind the limiter completely closed e automatic draught regulator button must be set to desired value e maximal fireplace operating temperature is 90 C IMPORTANT NOTE At the first firing some condensation may occur water dripping and occurrence of humidity within the ashtray In such case gradually increase temperature in fireplace and this will stop 6 2 OPERATION Fireplace is fired as all continually heated solid fuel boilers When you open the burner door of the fireplace put
6. dual combustion products Do not clean external fireplace surfaces with abrasive sponge because it may damage protection but with damp cloth with usage of soft cleaning agent Itis not allowed to cool down the fireplace using by damping the burner After cessation of heating season you must carry on with complete fireplace cleaning Water should be exhausted only in the case if it is necessary to carry out some installation repair After heating season manufacturer recommends to hang linen bag into the burner space filled with 1 2 kg of chopped limestone 9 DISMANTLING AND REMOVAL After finalization of working validity of this product it is necessary to release the product from mains connections water connections and heating installation exhaust the water and had it over to the companies involved in waste collection recycling Symbol recycle bin with strikethrough on figure according to European directives warns you about your obligation to deal with inapplicable products with care Osnovano 1990 ABC PROIZVOD d o o Milo a Obrenovi a 2 31000 U ice SRBIJA Tel 381 O 31 514 501 0 31 514 502 E mail office abcproizvod rs www abcproizvod rs
7. ion since this has built in thermal protection heat exchanger Thermal valve is not in the basic equipment of the fireplace It is advisable to install fireplace onto central heating open system and in any case it is compulsory to install thermal valve with the probe onto the fireplace and connection of the heat exchanger to the water system Without installation of thermal valve guarantee is null All connections on fireplace must be well sealed which should be visually checked prior to commissioning Mounting procedure is finished with water filling of entire fireplace and entire installation up to the necessary pressure FIREPLACE MAY NOT BE USED WITHOUT WATER Fig 5 Diagram of the connection of fireplace to central heating open system 3 4 9 6 8 7 Y Kid CO 15 1 Fireplace Vulkan back 10 Check valve 2 Smoke pipe 11 Pressure duct 3 Open expansion vessel 12 Connecting duct for water system 4 Conductive pipe 12 Hot water exhaust 5 Manometer 13 Thermal valve probe 6 Radiator valve 14 Connection for filling and discharging 1 2 7 Radiator 15 Return duct 8 Exhaust valve 9 Circular pump Fig 6 Diagram of the connection of fireplace to central heating closed system Kamin Vulkan zadnja strana Dimn
8. ndling In case of doubt that it is not operational contact seller or directly factory ABC PROIZVOD 5 SETTING INSTALLATION Design setting and installation of central heating is strictly done by a professional In case of poor system design and any defects on installation of system by such person which further may cause defective operation of the fireplace complete material liability and new expenses are solely born by the person entrusted with installation of heating system not the manufacturer representative or seller of fireplace Fireplace may be set in kitchen block or on some other appropriate place living room on condition to provide fireproof base sufficient space for handling aeration of the room and appropriate chimney During setting of the fireplace care must be taken of the following a Furniture and objects that are next to the fireplace must not be made of flammable materials otherwise distance from the fireplace must be at least 100 150cm b Inno case you should put shelves or similar wooden furniture above fireplace c Wall in contact with back of fireplace must be made of heat resistant material d Curtains must not be placed directly behind fireplace and on the side as far as possible e Flammable materials e g door frames wallpaper must be away from smoke pipes at least 20cm This may be decreased if smoke pipes have appropriate thermal insulation f Fireplace should be placed horizontally or
9. s considered inappropriate and thus dangerous such as Change of use into fireplace on solid fuel but without connection to the hot water installation 2 2 Important safety warnings 1 Fireplace must be mounted and connected to the central heating installation by authorized professional installer mechanic in compliance with this manufacturer s instruction He will give to the user operator of the fireplace basic explanation from this instruction 2 This fireplace may be operated only by trained competent and reasonable person Operation is prohibited to children 3 Keep away from hot surfaces and do not touch them Take caution that children disabled persons or persons with impaired reasoning capacity stay away from these surfaces 4 Do not use and store flammable objects and liquids that evaporate near fireplace 5 When using small household appliances near fireplace take care that their electric cable is not touching hot fireplace surface 3 DESCRIPTION AND TECHNICAL CHARACTERISTICS Fireplace for which this INSTRUCTION is made is constructed for heating with solid fuel coal or dry wood It is made of certified boiler plate of guarantied chemical composition and mechanical properties at high temperatures It is welded using latest welding procedures Testing of the fireplace is done with water under 3 bar pressure The fireplace has cast grate Based on the place of connection to the chimney fireplace is connected on the upper
10. some paper on the grate wood cut in pieces and fire it up Then gradually put heating material until fire becomes larger After that fill in the burner position ashtray behind limiter close fireplace door an set draught regulator to the desired temperature 6 3 TEMPERATURE REGULATION On the fireplace casing Fig 1 pos 3 there is installed draught regulator which has the function to set desired temperature and is consisted of numerically marked wheel from 0 9 regulator flap and capillary Draught regulator is capillary connected with probe whereat it collects data about water temperature in the fireplace Temperature in fireplace is the lowest when draught regulator button fig 1 pos 3 on number 1 fig 1a and the highest on number 9 fig 1 b When temperature begins to drop regulator flap automatically opens 3 5 mm which enables flow of secondary draught air and better combustion up to the desired temperature Setting of draught regulator depends on desired ambient temperature Important note In order to make draught regulator work properly it is necessary to connected fireplace to the chimney of proper dimensions Space between regulator flap and opening for airflow must be cleaned from time to time and to remove residual ash and other combustion products Avoid low water temperatures in the fireplace 50 60 C because it may lead to condensation If you notice any water collection in the ashtray just increase fireplace
11. you should elevate a little back side 2 4mm 5 2 CONNECTION TO THE CHIMNEY Being the very important element of the central heating system chimney must be of appropriate cross section regularly set regularly installed above roof and insulated Fig 4 Setting dimensions check of the existing chimney is done by designer of central heating installation based on the fireplace capacity fuel type and required drought for the fireplace Fireplace achieves stated power only if chimney has appropriate dimensions All connections of smoke pipes of the fireplace must be properly sealed Fig 3 Chimney must be properly above the roof according to instructions fig 4 Avoid placing chimney caps if they have side blinds For a potential placement of a chimney cap apply recommendation on fig 4 Fig 3 CONNECTION TO CHIMNEY Inappropriate connection of fireplace to chimney Appropriate connection of the fireplace to chimney Sealed Pipe AN Opening for cleaning E Sealed is sealed Opening for cleaning Opening for cleaning is Opening for sealed cleaning Sealed Opening for A cleaning Opening for is sealed cleaning Fig 4 Setting chimney above roof and setting smoke cap 1 5d 5 3 INSTALLATION Fireplace for central heating may be connected to open system Fig 5 and closed system Fig 6 of central heating installat
Download Pdf Manuals
Related Search