DS-6401HDI Series Decoder Server USER MANUAL
Contents
1. 1 ch HDMI output resolution 1600x1200 60HZ 1080P 1920x1080P 60HZ 10801 1920x 10801 60HZ 1080P 1920x1080P 50HZ 10801 1920x 10801 50HZ 1280x720 60HZ 1280x1024 60HZ 1024x768 60HZ HDMI Output Audio Video pI 1 ch DVI output resolution 1600x1200 60HZ 1080P 1920x1080P 60HZ DVI Output 10801 1920x 10801 60HZ 1080P 1920x1080P 50HZ 10801 1920x 10801 50HZ 1280x720 60HZ 1280x1024 60HZ 1024x768 60HZ Audio Output 2 ch RCA 2 0 2 4Vp p 600Q Video Compression H 264 MPEG4 Video Decoding 1080P 1920x1080P 720P 1280x720P UXGA 1600x1200 Resolution SVGA 800x600 VGA 640x480 Video Decoding Audio Video 1 ch at 1080P 1920x1080P 2 ch at 720P 1920x720P 4 ch at 4CIF resolution Channels Decoding Multi division Display Mode 1 2 4 Frame Rate PAL 1 16 25fps NTSC 1 16 30fps Ogg Vorbis 1RJ45 10 100 1000Mbps self adaptive Ethernet interface Audio Compression Network Interface Serial Interface 1 RS485 and 1 RS232 serial interface External Voice Talk 1 ch RCA 2 0 2 4Vp p 10000 Interface Alarm In Alarm Out Power Supply 12V DC Power Consumption lt 12W Working 10 C 55 C Others Temperature Working Humidity 10 90 198mm W x123mm D x39mm H 32 Appendix B FAQ Why cannot ping the decoder Please refer to Chapter 3 to configure the decoder IP address being in the same segment as your PC and check the cable and switch Why the tr2. C SaveRemoteCfgFile folder by default If user has saved the config file before select Import config file to device to import the existed configuration to the decoder Add decoder Modify decoder Delete decoder Remote Settings Add decoder Modify decoder Delete decoder Remote Settings Working status of decoder Esper eves conge Import config file to device Working status of decoder Working status of decoder Select Working status of decoder to view the status of decoder in the following list 22 Working status of decoder Decoding 264 Standard H Customized 704576 Decoding 264 Standard H Customized 176 144 No decod Unknow Unknow 00 No decad Unknow Unknow 0 0 44 TV Wall Settings Enable Disable decode output After having added the decoder the decoding channel is not in use by default Drag the channel to the blank interface on the right to enable this channel When a channel is enabled user may click E on the right bottom corner to disable this channel Decode output settings Decoder output settings By double clicking a channel of the decoder user can configure the channel Output name BNC output 1 name and video format to be PAL or Video f i PAL C NTSC NTSC Resolution 23 If the output name is set to VGA HDMI or DVI output then user can select the resolution from the drop down menu Window division con
3. HIKVISION DS 6401HDI Series Decoder Server USER MANUAL Version 1 0 Hikvision Network Digital Video Recorder User s Manual This manual as well as the software described in it is furnished under license and may be used or copied only in accordance with the terms of such license The content of this manual is furnished for informational use only is subject to change without notice and should not be construed as a commitment by Hikvision Digital Technology Co Ltd Hikvision Hikvision assumes no responsibility or liability for any errors or inaccuracies that may appear in the book Except as permitted by such license no part of this publication may be reproduced stored in a retrieval system or transmitted in any form or by any means electronic mechanical recording or otherwise without the prior written permission of Hikvision HIKVISION MAKES NO WARRANTIES EXPRESS OR IMPLIED INCLUDING WITHOUT LIMITATION THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE REGARDING THE HIKVISION SOFTWARE HIKVISION DOES NOT WARRANT GUARANTEE OR MAKE ANY REPRESENTATIONS REGARDING THE USE OR THE RESULTS OF THE USE OF THE HIKVISION SOFTWARE IN TERMS OF ITS CORRECTNESS ACCURACY RELIABILITY CURRENTNESS OR OTHERWISE THE ENTIRE RISK AS TO THE RESULTS AND PERFORMANCE OF THE HIKVISION SOFTWARE IS ASSUMED BY YOU THE EXCLUSION OF IMPLIED WARRANTIES IS NOT PERMITTED BY SOME STATES THE ABOVE EXCLUSION MAY NOT APP
4. 10 22 Rear bene eo A Ca la a a a alai bi la ai 10 2 A aa i no aa ti a a at it 11 2 3 1 Alarn Input Connections seen 11 22 Alarm Output Connect Ons ee 11 23 53 81 onal LME COMME CHONS srs n iran 12 CHAPTER capita do aaa ee oe ene eee de nee 13 Network Parameters Configuration 13 SEV Per fe rai a GSC UU asus een ie 14 3 2 Network Configuration by Hyper Terminal eee 16 CEAP TE R Merri sta ee a Ed a a aaa a 18 Decoder COMO id 18 4 1 Decoder Conf oure SOLARE u ee 19 4 2 Add Decoder asin iaaia 20 ES Decoder Contorno 21 A WW Al Setunsssacesea ee een Ense 23 4 3 Decoder ont re Eee ada d edi 25 IE Video DECO Eee DEE ind 26 A VCE DECO nee re 28 453 UZ COMO sec ee o dai du ta 0 dai Au d dada 30 CHAPTER N GE ani a act a a aa at uta c ua ata at neta i d a 31 Y 4 D GPRS RENNER coautor a at a i ct a i Ac da i ata 31 APPENAKA Pecos Appendix B PACO ao cool Appendix C Glossaries CHAPTER 1 Introduction 1 1 Description Developed by Hikvision based on TI Davaci platform DS 6401 HDI is a kind of multi purpose video audio decoder which is capable of allowing the coded images from HIK DVR DVS or other encoding devices to be decoded and displayed on the TV wall after transmission via IP network Specially designed for the allocation and management of the video surveillance system DS 6401 HDI supports multiple network transmission protocols and it applies the code downloaded in FLASH ensuring high stability and reliabilit
5. set in which the alarm occurs the device is capable of triggering corresponding alarm handling method relay output and buzzer alarm as well as upload to center etc O Relay Alarm Output The relay alarm output can be connected to alarm devices for alarm response actions e g combined aural and visual alarm unit etc which is capable of proceeding alarm handling within the arming period Exception Handling O Exception Alarm Handling Exception alarms include network disconnect alarm IP address conflict alarm illegal access alarm etc multiple alarm handling methods are supported relay alarm output buzzer alarm upload to center etc O Exception Reboot Software watchdog capability for inspecting important threads and system resources of device in case of exceptions cannot be recovered the device will be automatically rebooted Firmware watchdog for inspecting the firmware of device in case of exceptions in system task scheduling the device will be automatically rebooted User Administration A maximum of 32 users can be created by the system including 1 administrator and 31 users The user name of the administrator is admin which cannot be modified and the password is allowable to be modified by the administrator only no deletion of the administrator 1s allowed and the administrator is authorized to set the operation permissions for normal users SDK Interface O Transparent Channel The decoder adopts the RS232 R5485 s
6. view of decoded video Display of working status of selected Enter TV Wall control interface and the decoding channel will be displayed in the area according to user defined 25 configuration Click to hide the display of decoded video and status or click to resume display Description of the functional buttons on the interface TE Start playing the decoded video MM ME Stop playing the decoded video Start cycle decoding J Stopcycledecoding Stop cycle decoding Start Stop the live view of local Capture decoded video Kr eo E ooo y yo Note The display of TV wall will not be affected by starting or stopping the live view of decoded video 4 5 1 Video Decoding Select the decoding window and double click the desired channel from the device list and the decoder will start decoding for this channel The real time decoded video will be displayed on the live view panel and the current decoding status will also be displayed in the Channel list 26 Stop decoding Right click the decoding channel and select Stop decoding or click Mall to stop decoding on the current decoding window Start decoding When the decoding is disabled user can right click the decoding window or select Start decoding or click D to resume decoding Voice control Right click the decoding window and select Open voice option to open voice when the voice is turned on right click th
7. LY TO YOU IN NO EVENT WILL HIKVISION ITS DIRECTORS OFFICERS EMPLOYEES OR AGENTS BE LIABLE TO YOU FOR ANY CONSEQUENTIAL INCIDENTAL OR INDIRECT DAMAGES INCLUDING DAMAGES FOR LOSS OF BUSINESS PROFITS BUSINESS INTERRUPTION LOSS OF BUSINESS INFORMATION AND THE LIKE ARISING OUT OF THE USE OR INABILITY TO USE THE HIKVISION SOFTWARE EVEN IF HIKVISION HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES BECAUSE SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES THE ABOVE LIMITATIONS MAY NOT APPLY TO YOU Preventive and Cautionary Tips Before connecting and operating your DVS please be advised of the following tips e Ensure unit is installed in a well ventilated dust free environment e Keep all liquids away from the DVS e Please check the power supply to avoid the damage caused by voltage mismatch e Please make sure the DVS work in the allowed range of temperature and humidity e Please keep the device horizontal and avoid the installation under severe vibration environment e The dust board will cause a short circuit after damping Please dedust regularly for the board connector chassis fan etc with brush TABLE OF CONTENTS CHAPTER A a i alea 5 AIM ee ee eier 5 KEDE ck yo nen tee ee nase 6 A SAVU gt OA O ES E EE O ER E e aaa uda bata cat 6 A a ef ate aaa iat lift anca Brat lun azotat Paint n 9 e iar d lata alta il at i al ii 9 A ea cual ni za A da ea za n za i
8. ansparent channel has been set but the encoder still cannot receive data 1 Check if RS232 has been set as transparent channel first 2 Check the connection of encoder Why cannot add decoder with software 1 Check the decoder IP address 2 Cable is connected 3 User name and password of decoder are correct e Why cannot play back the recorded file in DVR with decoder 1 Check the DVR network connection 2 Check the parameters of the playback file 3 Check if there are files existed in the selected time range Why cannot decode the stream transported by stream media server 1 Check the network connection between decoder and stream media server 2 Check if the stream media server port is connected with the port added on decoder 33 Appendix C Glossary Dual Stream Dual stream refers to that one channel of video stream can be divided into double independent output streams through the video encoder Shown as below Main Stream Video Stream Video Encoder Sub Stream The resolution frame rate bitrate and other parameters of the output stream are independently programmable The two streams generated may meet different application demands e g one stream is used for HDD storage and the other for transmission via Internet Transparent Channel The transparent channel indicates the channel used for transmitting data and through which the data transmitted receives no handling and thus retains no cha
9. e decoding window and select Close voice option to close voice Note Only the Audio amp Video stream type can support the function Open voice Select the decoding window and the current decoded video images will be displayed on the live view display area Click the icon from the toolbar to stop the live view of decoded video if required and clicking gt may start the display of decoded video again Refer to the following figure 27 When in live view state user can click El to capture the current picture for local storage Click the icon CI to start recording and then the state of the icon will be changed ol click 1t again to stop recording 4 5 2 Cycle Decoding Drag a device or group node to the designated decoding window and then all channels under this device or group will be decoded in cycle The real time decoded video will be displayed on the live view panel and the current decoding status will also be displayed in the Channel list 28 Pause cycle decoding Right click the current cycle decoding window and select the Pause cycle decoding or click MM to pause the cycle decoding When the cycle decoding is in paused status user may right click on the decoding window and select Resume cycle decoding or click Adi to start cycle decoding again E Configure the cycle decoding dwell time Click EEMI to enter the setup managemen
10. erial interface to realize transparent transmission The data sent remotely to the decoder via network can be transmitted by RS232 RS485 interface of decoder without any handling and the transparent channel of the decoder supports multi cast transparent transmission as well and multiple transparent channels can be established simultaneously e PTZ Control Through SDK transparent channel the PTZ of DVR or DVS can be remotely controlled O Voice Talk The decoder is capable of realizing voice talk with the remote client When the client has submitted application the voice talk between the client and decoder is created CHAPTER 2 Structure 2 1 Front Panel DS 6401HDI Front Panel PWR LINK RX TX RESET LED Indicator amp Connections Interface INCI av pat OO e voor TN 2 2 Rear Panel DS 6401 HDI Rear Panel RS485 T T RFR TG Z2 G G GOUT AUDIO OUT o 00 MIC IN MIC IN Voice talk input AUDIO OUT R L Audio out for connection to audio output device e g sound box R right channel L left channel 8 alarm outputs 8 alarm inputs En RS232 Connect to RS 232 devices e g PC etc 10 DC12V 12VDC power input Pe ex owning SOS 2 3 Alarm Connections 2 3 1 Alarm Input Connections DS 6401HDI supports the open close relay input as the alarm input mode For the alarm input signal not in open close relay signal mode please follow the connections shown as below Alarm input connections
11. figuration By right clicking the decoder channel user can select the screen division mode Currently all of HDMI DVI BNC and VGA outputs can be selected to 1 or 4 division display modes After configuration of the window division if it has reached the limit of decoding source then the system will display the warning message of decoder channel not available when the user continues to enable the decode output channel Decoder output settings Output name Video format Resolution HDMI output fe PAL UXGA 1600 1200 60HZ 720P 1280 720 50HZ 10801 1920 1080 60HZ 10801 1920 1080 50HZ 1080P 1920 1080 50HZ 1080P 1920 1080 60HZ UXGA 1600 1200 60HZ After having enabled the decoding output and configured the display mode user can change the size and position of the display window Click the mouse and hold on the title below the window to change its position By dragging a border of the decoder user can change the size of the window You can also use the layout toolbar to adjust the size and position 24 Refer to the following table for the description of layout toolbar Align lef Flush right Align top oll Flush bottom Se ee 5 MET mm al A II 4 5 Decoder Control After having finished the decoder addition and TV wall configuration click the icon TV Wall to enter the decoder control interface from selected decoding decoding channel channel Live
12. for Emerson Alarm 4435 optocoupler Note the corresponding relay input port of DS 6401HDI should be set to NC mode Alarm input connections for Normal Alarm JOC 3FG DS5 6401 H DT 24V Relay 2 3 2 Alarm Output Connections DS 6401HDI supports the open close relay input as the alarm output mode The alarm input can be selected to NO or NC Different alarm output connection methods are applied to the AC or DC load please refer to the following diagram 11 Please note the different connections of JJ1 shown above For DC load JJ1ca be safely used both in NC and NO methods and it is recommended to use within the limit of 12V 1A For external AC input JJ1 must be open The motherboard provides two jumpers each corresponding to one alarm output By factory default both of two jumpers are set to be connected 2 3 3 Signal Line Connections DS 6401HDI Decoder provides the green terminal plug for connecting signal lines Follow the instructions shown below 1 Disconnect the green terminal plug from the terminal socket on the device 2 Use the standard screwdriver to loosen the screws on the plug and then insert signal lines to the plug and under the spring washers and finally tighten the screws 3 Connect the plug with signal lines to the corresponding green terminal socket 12 CHAPTER 3 Network Parameters Configuration Description e This chapter is about the network parameters configuration of Hikvi
13. g setGateway 192 168 1 10 getTime Show decoder current time Command format getTime Enter set Time Setup decoder time Command format setTime 2009 4 15 15 30 00 showBootTime Show decoder boot time Command format showBootTime Enter showUserInfo Show decoder current user information Command format showUserInfo Enter Note For other commands please consult our technical engineers 17 CHAPTER 4 Decoder Configuration Instruction o Before configuration user need to do the network configure according to the chapter3 O Connect the decoder to the LAN O Prepare a PC connected to the same LAN with the decoder 4 1 Decoder Configure Software Run the disk of 1VMS4000 V2 0 software which is supplied by HIKVISION and double click the icon to set up it in your PC The following section has described the configuration of decoder through the software Please refer to the user manual of 1VMS4000 V2 0 for more details The following figure shows the interface after access to the software iVMS 4000 a Preview Playback v Map Setup TV Wall Help Useruserd1 Sort by Software Preview 3 Channel 13 3 Channel 14 3 Channel 15 3 Channel 16 28 8116HF 3 Channel 01 3 Channel 02 3 Channel 03 3 Channel 04 3 Channel 05 3 Channel 06 3 Channel 07 3 Channel 08 3 Channel 09 3 Channel 10 3 Channel 11 3 Channel 12 3 Channel 13 8 Channel 14 8 Channel 15 3 Channe
14. ia remote access to the encoder or streammedia server and decoded for local output A maximum of 64 channels are allowed for cycle decoding Obtain stream from streammedia server receive real time data by remote access to HIK stream media server and then decode stream for local output The HIK RTSP is adopted as the control protocol and the TCP UDP is used for receiving the data stream Remote playback of encoder s record files by remote access to the encoder with storage capability and directly obtain the record files from the encoder and finally decode for local output Passive decoding the decoder passively receives stream sources and then proceeds decoding and transmission Passive decoding supports TCP and UDP transmission modes Network e One 10 100 1000Mbps self adaptive UTP Ethernet interface Support TCP IP UDP and RTP network protocols O Get allocated IP address sub mask and gateway via DHCP server O Accomplish auto time adjustment for decoder over NTP protocol e Support DDNS capability O Capable of searching decoder in real time through SADP software as well as modifying the IP address sub mask gateway of decoder and some other parameters e Capable of accessing decoder by TELNET command to view device information modify network parameters etc Alarm O Relay Alarm Input The decoder provides alarm input output ports in relay signal input mode which can be set to NO or NC Four different arming periods can be
15. l 16 Note This software is supplied by HIK VISION for configuration of the decoder though it also has the function of configuring the encoder this chapter only instructs the decoder configuration For more instructions please refer to the user manual of 1VMS 4000 V2 0 19 4 2 Add Decoder Click AM gt and then click EAEE gt to enter the decoder settings interface VMS 4000 IVMS 4000 Right click the Decoder list and select m Preview Playback Preview Playback Add decoder or click del to add decoder Decoder list rex Decoder list Add decoder Add decoder Input decoder name IP Port Username Decoder settings Decoder information Decoder type 1080P DS 6401HDI Decoder IP 172 18000 Password and click OK to finish adding decoder Note user can also click the Online Decode Username option to select and add the online device CIF 4CIF 720P and 1080P can be selected according to your decoder model and Decoder type different model of decoder could have different decode performance Decoder name The name of the Decoder which can be user defined Decoder IP The IP address of the Decoder Port The device port of the Decoder Username Password The username and password of the Decoder 20 The 6401 HDI decoding source is described as below CIF 4 channel decoding ACIF 4 channel decoding 720P 2 channel decoding 1080P 1 channel dec
16. nge By remotely connecting the keyboard with the decoder the transparent channel can be established to realize control of dome or Pan Tilt unit connected to remote encoder Resolution The type of resolution can be divided into the display resolution image resolution and pixel resolution The display resolution refers to the maximum display zone on the screen in certain display mode measured in horizontal and vertical pixel The image resolution describes the detail a digital image holds measured in horizontal and vertical pixel as well In case the image resolution is higher than the display resolution proportion of the image will not be displayed on the screen The pixel resolution indicates the ratio of the pixel width and length Different pixel width length ratio will result in different shape of image Generally the image resolution is applied to the digital surveillance PAL QCIF 174 144 CIF 352 288 2CIF 704 288 DCIF 528 384 4CIF 704 576 NTSC QCIF 174 120 CIF 352 240 2CIF 704 240 DCIF 528 320 4CIF 704 480 Streaming Server The streaming server refers to a dedicated computer system or server which runs the corresponding streaming media software to provide the delivery of data It is generally applied to the delivery of the same massive data which may greatly reduce the load of the host as well as save internet resources 34
17. oding Decoder list After added successfully the decoder channels will be displayed in the decoder list 6401HDI Series decoder ER 1050P D5 6401HDI iam tee supports VGA so it displays the BNC and VGA outputs EH ENC output 1 ies VGA output 1 differently mu HDMI outputl EE DVI output Right click a decoder and select Modify decoder Decoder list or click Bo user can modify the decoder select Delete decoder or click AR to delete it 3 il Delete decoder Remote Settings Export device config file Import config file to device Working status of decoder Note Each decoder is recommended to be added in one 1VMS 4000 software only avoiding disordered control caused by one decoder added in multiple software terminals 4 3 Decoder Configuration Select a decoder right click it and select Remote Settings to enter the decoder Remote setting interface 21 Remote setting E Device Parameters i P Device Information Version Information a 1 Network Parameters Embedded multiDecode P Network Settings P DINS Settings E in P HIP Settings E La Serial Port Settings JP R5232 Settings p R5465 Settings E Alarm Parameters i P Alarm Input Settings i Exception Parameters Ey Account Management Ey Update Remotely Export import config file Right click a decoder user can select Export device config file and save the device configuration file in
18. phone number that you want to dial Countyvregion hina S6 Area code Connect using v Step4 Serial port setup Set port parameters in COM 1 Properties dialogue box as the following figure COM1 Properties Port Settings Bite per second Data bits Parity Stop bits Flow control Restore Defaults The parameters should be Bits per second 115200 Data bits 8 Parity None Stop bits 1 Flow control None Press Apply and OK after the setup Press Enter under Hyper Terminal interface When root dvrdvs appears the connection is established 15 HK HyperTerminal File Edit View Call Transfer Help Step5 Disconnect and save connection According to the tips disconnect and save HK for the next time After saving there will be a new Hyper Terminal item established in the program group Start gt Accessories gt Communications gt Hyper Terminal Connection names of all Hyper Terminal are included You can see an icon named as HK here Hyper Terminal Hyper Terminal You are currently connected Do you want to save the connection named HK Are you sure vou want ta disconnect now 3 2 Network Configuration by Hyper Terminal Enter Hyper Terminal Click Start gt Programs gt Accessories gt Communications gt Hyper Terminal gt HK then the Hyper Terminal inte
19. rface will appear as figure below Type Enter and the prompt root dvrdvs will appear which means connection between RS232 interface of PC and RS232 interface of DS 6401HDI is established successfully by Hyper Terminal The following operation commands are to accomplish the parameters setup in the prompt 16 HK Hyper Terminal File Edit view Call Transfer Help Be 55D root durdvs helpm PPPPPPPPPEPPTTITI tt multiDecode commands usage getlp get the device s ip setlp set the device s ip e g setlp 192 168 1 10 255 295 255 8 getGateway get the device s gateway setbateway set the device s gateway getlime get time setlime set time e g setlime 2009 4 15 15 30 00 showDevBoot Time show device boot time showUser Info show login user info enableSwhWatchdog enable soft watchdog disableSwWatchdog disable soft watchdog Ser SAA Tn ES E show bootParms info wi ls i i a ua U e Commands Description Commands Utilities helpm Console help command is used to print common commands show as Figure 3 2 getlp Show the current IP address of decoder Command format getlp Enter setIp Setup decoder IP address Command format setIp IP mask e g setIp 192 168 1 10 255 255 255 0 Show current decoder gateway address Command format getGateway Enter Setup decoder gateway getGateway setGateway Command format setGateway Gateway e
20. sion DS 6401 HDI Decoder o The DS 6401HDI factory default user name is admin and password is 12345 o The DS 6401HDI factory default IP address is 92 0 0 64 The network parameters need to be setup before the decoding channel configuration The network parameters are used to connect with the software which is applied to set the decoding channels The network parameters are including IP address subnet mask gateway and port 3 1 Hyper Terminal Setup The common method is to connect decoder and PC with serial line run Hyper Terminal and modify parameters with serial command Please connect the RS 232 port of decoder with the COM port of PC directly power on the decoder and PC and follow the steps Step1 Enter Hyper Terminal Click Start gt Programs gt Accessories gt Communications gt Hyper Terminal in Windows system and the dialogue box below will appear as the following figure Connection Description ESB New Connection Enter a name and choose an icon for the connector Mame Step2 Name the connection and define the icon Input a name e g HK select an icon and press OK to enter Connect To dialogue box Step3 Select the communication port Select COM1 in Connect To interface Please select the COM port according to the reality in case PC has more than 1 COM Press OK to enter Properties dialogue box 14 Connect To Enter details for the
21. t interface and then click Local Settings to enter preview settings interface refer to the following figure which allows user to set the TV Wall Dwell Time After configuring the time click the Save button to save the configuration Note it is recommended to set the dwell time of cycle decoding to be longer than 5s 29 4 5 3 PTZ Control If the decoder is connected with PTZ user can operate the PTZ control through the client software There are 8 directional keys to control PTZ movement and the sliding bar is used to change PTZ speed which 1s adjustable from 1 to 7 and the default speed is 4 Click amp key to start auto scanning and click it again to stop scanning Click the function keys on the right to adjust focus iris and zoom If the PC is connected with 1002KI 1003KI keyboard or USB joystick the PTZ can also be controlled by them Note If the current decoding window is under cycle decoding the cycle decoding will be paused while operating PTZ control and when the PTZ control is finished the cycle decoding will be resumed Call preset User may double click the existed preset in the preset list to call the selected preset of dome camera 30 CHAPTERS Appendix Appendix A Specifications Model DS 6401 HDI 1 ch BNC output resolution PAL 704x576 NTSC 704x480 1 ch VGA output resolution 1280x720 60HZ 1280x1024 60HZ 1024x768 60HZ CVBS Output VGA Output
22. y of system performance DS 6401 HDI Video Audio Decoder adopts higher integrated TI Davaci processing chip which provides powerful decoding capability It supports multiple bitrate transmission methods and is capable of decoding outputting the high definition 1080P video stream and outputting decoded images via BNC and VGA ports simultaneously In addition the Decoder also has the capabilities such as voice talk alarm input output PTZ control etc providing powerful support for the large TV wall decoding service 1 2 Features Decoding O Decoding images and audio HIK H 264 and standard H 264 video compression methods Support PS RTP and HIK customized encapsulation formats PAL and NTSC image formats Decoding at up to 1080P resolution G 722 G711A and G711U video compression methods O Decoding Resources DS 6401HDI is capable of decoding 1 ch video stream at 1080P resolution 2 ch video at 720P resolution and 4 ch video at 4CIF resolution O Decoding Mode Multiple transmission methods support TCP UDP RTP over TCP RTP over UDP Dynamic decoding log on the remote encoder or remote streammedia server to select a channel of video source to acquire video stream and then decode and output the video for local display Cycle decoding set multiple remote monitoring channels on a decoding channel and the decoder is capable of performing cycle decoding according to the configured sequence and time The stream sources can be obtained v
Download Pdf Manuals
Related Search