- Picomed
Contents
1. Serialnumber Check the IR receiver for damages Clean it Make a functional test Reprogram the ER x AC IR receiver so IR formats and usercodes used by a person not can be misused in any circumstances The following settings are recommended Usercode 0 Q Channelgroup Gewa 0 Channel 0 Format New Assistant Ooooo 3 Productinformation Picomed ER2AC and Picomed ER4AC IR receivers have 2 or 4 channels controlled by infrared IR light The receivers are developed to control lov voltage products up to 48 V They can also control 230 VAC via external relays They shall be powered with 12 24 VAC VDC They can be programmed to receive ordinary codes or lock codes They can read the following IR formats New Assistant 32 usercodes with 16 channels in each New Assistant lockcode 12 bit Gewa Infralink 4 groups with 16 channels in each Gewa Infralink lockcode old 10 bit Gewa Infralink lockcode new12 bit The IR receiver can be programmed to respond on both New Assistant and Gewa if needed e ER2AC has 2 channels relays e ERAAC has 4 channels relays Each relay output can be individually programmed to on off hold or impuls If the IR receiver is programmed to respond on lock codes it will only work on channel relay 1 3 1 Accessories The IR receiver is assembled with a printed circuit board inside a plastic box On the front there is a keypad foil with keys product name and a light indicator2. The partnumbers are Description Picomed partnumber Infrared receiver 2 channels ER2AC Infrared receiver 4 channels ERAAC A functional test should be done together with an IR transmitter Tip do it before the IR receiver is dismounted Both the IR receiver and the IR transmitter has to be prerogrammed with the same user code and channel Ensure that the IR receiver responds on the receiverd IR signals ER2AC ER4AC Page 8 3 2 Technical data Type Controlled by Number of channels Powersupply Current consumption Temperature Connections Weight Materiale Settings Neccessary depth when flush mounting 24 Picomed ER2AC ER4AC infrared receiver 2 4 channels From an IR remotecontrol 2 4 potential free relays 0 5 A 48 Volt External powersupply 9 24 VAC DC 50 mA 10 up to 40 C Internal screw terminals Ca 100 g Plastic Usercode Channel Lockcode Relay working mode 35 mm ER2AC ER4AC Page 9 The receiver does not Check power supply Disconnect IR sensor if Call Your technichian work at all connected The receiver does not The IR sensor is The IR sensor is defect Call Your technichian work when IR sensor is exposed to direct and has to be changed connected The receiver does not work when the sun 1s shining on it The receiver is connected to a common door and works only for some users The receiver works somethimes or in intervals The rece
3. 0 1 13 0 1 1 0 1 2 14 0 1 1 1 0 3 15 0 1 1 1 1 0 16 1 0 0 0 0 1 17 1 0 0 0 1 2 18 1 0 0 1 0 3 19 1 0 0 1 1 0 20 1 0 1 0 0 1 21 1 0 1 0 1 2 22 1 0 1 1 0 3 23 1 0 1 1 1 0 24 1 1 0 0 0 1 25 1 1 0 0 1 2 26 1 1 0 1 0 3 27 1 1 0 1 1 0 28 1 1 1 0 0 1 29 1 1 1 0 1 2 30 1 1 1 1 0 3 31 1 1 1 1 1 2 3 5 User code and channel programmed with an IR remotecontroller A fast mode programming mode is also available A preprogrammed IR remote controller can be used ER2AC ER4AC Page 6 24 PICOMED e Press and hold the 0 button for 5 seconds to enter the programming mode The LED shall be lightning e Press the 1 button once the LED will start flashing rapidly e Transmit the signal from the IR remote which shall control the first relay in the IR receiver e The LED will flash twice e Finish by press amp hold the 0 buttons for 5 seconds The IR receiver will read the IR signal and store it in its memory When programming the receiver in this way ONLY the signaltype programmed in the IR transmitter will be stored If the IR receiver shall respond to more than one IR signal the IR receiver shall be programmed with the programming buttons 2 3 6 Lockcode programmed with buttons The lockcode is a special code consisting of 12 bits to obtain higher security PW to use for choosing the Lock code shall start with 0 The PW shall be like this 0 XXX XXX XXX XXX Press and hold the 0 button for 5 seco
4. 3 PICOMED Environmental Control Documentation for Picomed ER2AC and ERAAC R receivers with 2 and 4 channels Brokelandsheia 4993 Sundebru TIf 47 3711 9950 Fax 47 3711 9951 E mail firmapost picomed no Foretaksnr 962 211 631 MVA 33 PICOMED Documentation ER2AC and ERAAC IR receiver Versions Date Made by Comment 210205 Bent Havard Sollid English version based on Norwegian version 0303 Table of contents 1 conati redu 3 1 1 Water humidity eleanig us io oq itas uiid inei 3 soe a PO Mex Nenad Mich len o MM ce ea 3 eS NTalbutie HOBIBB eno iE tL E tu 3 2 doeumentatiOl 3 2 Penodically maintenance e I end LU Ua sede REA 3 2222 NTOWDEITIB het tei onmi oes tato bits E 3 ZU doctore scd E 4 2 2 2 Wiring diagram uisu closet o RENE SEIEN Ie FRUTA 4 2 2 3 ARsreDOrver wathvIoCE GoOde Desert oon ec ite aa E isque 4 23 SHIP TQ 4 2 3 1 How to program LR receiver b EUIS peto apres lee aa Pie 5 2 3 2 LED behaviour during programming mode sese 3 2 3 3 Programming memory esses iret e rr TUER sh PARAR LUST 6 2 3 4 User code and channel programmed with buttons eese 6 2 3 5 User code and channel pr
5. C Page 3 24VDC GND GND IR IR LED LED 24 PICOMED 2 2 1 Electrical connections The IR receiver shall be powered by 12 24 VDC AC and shall only be connected to approved powersupplies All connections shall be made without an active powersupply The minimum cable area shall be 0 22 If necessary it is possible to connect an additional IR sensor to the IR receiver Also two IR receivers can be connected together and work as IR sensors for each other An IR signal will be adducted to the other IR receiver via the IR bus The IR sensors have to be programmed with the same user code The IR bus has 4 connections 1 IR BUS signal 2 Ground 3 IR BUS LED 4 lt 24 To connect different receivers to each other they have to use same powersupply 2 2 2 Wiring diagram ER2AC ER4AC O RLI 24VDC ARL 2 2 3 IR receiver with lock code Picomeds IR receivers are designed to work together with Abloy and Picomatic dooropeners Usually these advanced door openers will be connected to only one relay output When the IR receiver is programmed with a lock code signal it will activate both relay 1 and 2 The signal on output 2 will be activated a little bit before channel 1 and it is ment for lock systems which not can be controlled by the dooropener 2 3 Programming The ER2AC and ERAAC IR receiver can be programmed by the 2 push buttons next to the LED on the PCB It is also possible to use th
6. ese buttons in combination with a preprogrammed IR transmitter and obtain a fast mode programming The front cover has to be removed to get access to the buttons The power supply has to be connected to the IR receiver but no electrical components shall be connected to the relay connections The receiver will not loose any settings during a power loss ER2AC ER4AC Page 4 24 PICOMED knapp 0 knapp Lysdiode IR sensor The main components on the PCB are two programming buttons 1 knapp 0 knapp one LED Lysdiode and a IR sensor on the PCB The programming buttons are indicated as 0 and 1 binary notation The following parameters can be programmed e User code and channels e Lockcode e Working mode for the relays User code and channel can be set with the help of a preprogrammed IR remote controller The working mode for the relays has to be set with the programming buttons The receiver can be reprogrammed any time and there is no limit for how many times it can be reprogrammed 2 3 1 How to program the IR receiver e Enter programmaing mode by press amp hold the 0 button for 5 seconds Let off the button when the LED is lightning e The programming can be done by writing programming words PW which consists of sequences containing 0 and 1 The PW s should be written down before the programming starts to avoid any trouble due to timeouts during the programming e Ifa wrong input is made press an h
7. etic campaibility Generne emission standard part Residential commercial and light industry 0182 1 Electromagnetic Cienersc immunity siarxlard part 1 Residential commercial and light industry e EN 60601 1 1988 12 IEC 601 1 1 988 Medical electrical equipment Pt 1 General requirements for safety Defined ns a Class B product int powered equipm Supplementary information The products compiles wiih the requirements of ile following directives Low Voltage Directive TA 22 EEC Medical Devices Directive 9W42 ERC Class T The products carries the CE mark accordingly The CE mark was first applied in ihe year 2000 The technics documentatian relevant to the above equipment will be hele bey us Gjersa Norway Dh may 2004 bak ul Location Date Beni H vard Sala Development Manager 99 Sumber Tel 37 11 99 317 11 990053 E mail firmaga pacomal sn 562 211 831 AVA ke 2238 03 05914
8. iver works for a while and seems to be reset Brokelandsheia 4993 Sundebru TIf 47 3711 9950 Fax 47 3711 9951 E mail firmapost picomed no Foretaksnr 962 211 631 MVA sunshine It has to be moved to a place where it not is exposed by sunshine It has to be moved to a place where it not is exposed by sunshine Not correct programmed Check the user manual Not correct programmed Check the user manual The receiver is connected to an inductive load relay etc which not is not protected with a diode Call Your technichian Call Your technichian Call Your technichian Call Your technichian PICOMED EC DECLARATION OF CONFORMITY Manufacturers name and address Picomed as Broke 899 SLTMDIEBRLT Norway Deckare under our sabe responsibility that the product Picomed Infrared Receivers ERx series Madii names s ERI ERA Are in conformity with the following standards 144 998 03 Medical devices Risk amalvaia NS EN 12182 2000 02 Technical aids for disabled person General requirements amd test methods NS EN ISO 497 2001 04 Medical devices Application of risk management t modical deviers 1540 497 1 200 C0c7 gendum ACS O01 imoarparabed NS EN 180 1497 1200 AL 2003 205 Amendment AL Medical devices Application af risk management bo medical devices Ansendment 1 Rationale for requirements S0 AM D 2404033 50081 1 Electromagn
9. nds and let off the button when the LED lit Press the 0 button once the LED will start flashing rapidly Enter the 12 bit lockcode to be used The LED will flash twice Finish by press amp hold the 0 buttons for 5 seconds 2 3 7 Lockcode programmed with an IR remote controller A fast mode programming mode is also available A preprogrammed IR remote controller can be used e Press and hold the 0 button for 5 seconds to enter the programming mode The LED shall be lightning Press the 0 button once the LED will start flashing rapidly Transmit the lock code signal from the IR remote The LED will flash twice Finish by press amp hold the 0 buttons for 5 seconds 2 3 8 Relay functions The relay functions can be set to e On Off e Impulse 1 or 4 seconds e Hold This can be set with the programming buttons Each channel relay can be programmed individually PW to use for relay functions shall start with 1 1 0 0 0 The PW shall be like this 11000 X0 YO X1 YI X2 Y2 Setting Xn Yn Output function on the relay 0 0 On Off 0 1 Impulse 1 second ER2AC ER4AC Page 7 24 PICOMED 1 0 Impulse 4 seconds 1 1 Hold 2 4 Recycling When the IR receiver shall be recycled to be used by an other user the following should be done If there is any need to file this process make copies of this page fill in serialnumber and make a cross next to each point to be done
10. ogrammed with an IR remotecontroller 6 2 3 6 Lockcode programmed with buttons 7 2 37 Lockcode programmed with an IR remote 7 2 23 00 Relay DUBCHIGOHS externas 7 S ree cO 8 3 JProducanforiiatlon sss cs ortho te yada i dio utt if etude i Tal od 8 3 1 JAGDOSSOLI S ists ie cred rto to Le ess elas indices Pa dea dee 8 3 2 ke HNC Al X E EETA 9 ER2AC ER4AC Page 2 24 PICOMED 1 User manual Picomed ER2AC and ERAAC receivers for InfraRed IR light receives IR light emitted from IR transmitters To receive these signals it is an advantage that the receiver not is covered by anything which can block the emitted signal from the transmitter Usually the IR signals will be reflected by floor walls and roof so in most cases there is no need to point directly against the receiver with the IR transmitter The distance between the receiver and the transmitter should be more than 1 metres to make the most of this reflection effect The receiver will be controlled by a transmitter with the same type of IR signals and the correct codes There is no need for maintenance for the IR receiver and there is no batteries etc which has to be changed If the IR receiver needs to be cleaned it can be cleaned with a humid cloth alterna
11. old the 0 button for 5 seconds to leave the PW and go back to programming mode without saving data e There will be a timeout after 60 seconds if no keys are pressed e When entering of a PW is started a pause of more than 15 seconds between two bits will result in timeout of a PW e Only completed PW will be stored 2 3 2 LED behaviour during programming mode In programming mode the LED will be on When a PW is started the LED will flashing rapidly When entering a bit the LED will turn of for a moment When a PW is done and all bits accepted the LED will flash slowly twice The IR receiver will have the same behaviour when it is programmed by the help of an IR transmitter ER2AC ER4AC Page 5 2 3 3 Programming memory 24 PICOMED All settings which are programmed will be stored and they will not be changed during a power loss The power supply has to be connected during the programming sequence 2 3 4 User code and channel programmed with buttons PW to use for choosing the user code shall start with 1 0 0 0 The PW shall be like this 2 Al 0 03 D2 1 0 lo 0 4 The table beneath shows the usercodes and channels Gewa chan Usercode Ay A A Ag nel group 0 0 0 0 0 1 1 0 0 0 1 2 2 0 0 0 1 0 3 3 0 0 0 1 1 0 4 0 0 1 0 0 1 5 0 0 1 0 1 2 6 0 0 1 1 0 3 7 0 0 1 1 1 0 8 0 1 0 0 0 1 9 0 1 0 0 1 2 10 0 1 0 1 0 3 11 0 1 0 1 1 0 12 0 1 1 0
12. tively use a mild soap There is a red light indicator in the front of the IR receivers which will lit when it receives a known IR signal Keep in mind that it should not be covered by anything which can prevent the IR signals to reach it and it should not be exposed for direct sunlight 1 1 Water humidity and cleaning Picomed ER2AC and ERAAC is ment for indoor use Do not spell liquids on the receiver while it can destroy it 1 2 Cleaning It can be cleaned with a humid cloth alternatively use a mild soap 1 3 Malfunctioning Contact Name Telephonenumber 2 Technical documentation The IR receiver is ment to be wall mounted in a standard box It can also be flush mounted in a standard box There is no need for any dissasembling for periodical maintenance inspections or repairments 2 1 Periodically maintenance The IR receiver is developed to work without any need for periodical maintenance There is no internal battery to be changed 2 2 Mounting Picomeds IR receiveres ER2AC and ERAAC is ment for wall mounting All electrical wires shall be disconnected when mounting the receiver It shall be mounted in a place where it not will be covered by anything which can block the IR signals Even so it is very often possible to place it behind curtains etc and still it will work to the users satisfaction Direct sunlight which shines on the receiver will very often reduce the receivers sensitivity ER2AC ER4A
Download Pdf Manuals
Related Search