USER MANUAL - Casall Base
Contents
1. 12 13 14 15 16 17 18 UHECK SCCULILY OL SAUUIE Remove handlebar post and clean tube Remove seat post and clean tube Check brake pads for wear align Check brake adjustment Check security of all knobs amp release lever Check toe straps for signs of wear Check crank bolts and re tighten Make sure pedals are screwed in Check belt tension Wipe the anti rust oil on the flywheel Surface because people sweat on flywheel Check bottom bracket Check flywheel bearings Full service frame inspection RK MR KM KM KM _ x INDOOR BIKE2. the Release lever Adjusting the seat height undo the knob located where the seat post fits into the frame Adjust the seat to the required height Then retighten the knob Make sure it is tight enough to prevent the seat from twisting side to side The seat position can be adjusted forwards and backwards Undo the knob located directly to the side of the seat slider Loosen the knob then slide the seat to the required position Then make sure the knob is re tightened Pedals and toe straps your feet should be securely positioned in the toe clips during exercise Put your foot as far forwards as you can into the toe clip and then pull the strap tight The bike should operate on a level surface with no lateral movement There are height adjuster caps located on either side underneath the rear foot Turn these caps clockwise or anti clockwise until the bike is totally stable on the ground Maintenance If any parts become loose or there is noise from the flywheel please contact your supplier as it may be unsafe Like any other mechanical cycling device the bike should be regularly maintained Ask your supplier for a detailed maintenance program Maintenance Chart No DESCRIPTION Daily Weekly Monthly Quarterly Annually 00 Keep machine clean Wipe machine down with clean amp dry fabric to clear X dirt amp sweat Wipe Anti rusty cream or similar on the seat post set handlebar set Visual check X X 10 11
3. 42 Seat post 1PC 19 Screw amp nut 1 PC 43 BB bearing 2 PCS 20 Spring bracket 1PC 44 Washer for bottle cage 1 PC 21 Handlebar w slider 1PC 45 Flywheel 1 SET 22 Release lever w washer 1PC 46 Outer chain guard bolt M5 3PCS 23 Handle bar post 1PC 47 Belt pulley w screw 1SET 24 Outer chain guard 1PC Instruction Use 1 This bike is designed to be used as a spin cycle It has a fixed wheel driven flywheel and the momentum will keep the flywheel and pedals turning even when you stop applying pressure If you wish to stop 2 3 4 suddenly apply the emergency brake Emergency brake Press down brake system 31 for stop Installation it is important that the bike is correctly assembled If in doubt contact the retailer for assistance Handlebar and seat adjustment It is important that the handlebar and seat are set at the correct height for your body Ask your instructor for assistance Adjusting the handlebar height Undo the knob located where the handlebar post fits into the frame Slide the handlebar post up or down to the required height and re tighten the knob Make sure it is securely tightened and that there is no lateral or vertical movement of the handlebar The handlebar position can also be adjusted forwards or backwards Undo the Release lever located below the handlebar slider Slide the handlebar assembly forwards until you reach the required position Then securely re tighten
4. USER MANUAL INDOOR BIKE XTR PRO 91025 Safety Instructions Xx XK A KK XK XK XK KE KE KE AE KX AE A RR Consult your physician before starting with any exercise program to receive advice on the optimal training Warning incorrect excessive training can cause health injuries Stop using the bike when feeling uncomfortable Please follow the advice for correct training as detailed in the training instructions Ensure that training only starts after correct assembly adjustment and inspection of the bike Always start with a warm up session Only use original parts as delivered Follow the steps of the assembly instruction carefully Only use suitable tools for assembly and ask for assistance if necessary Place the bike on an even non slippery surface For all adjustable parts be aware of the maximum position to which they can be adjusted Tighten all adjustable parts to prevent sudden movement while training This product is designed for adults Please ensure that children only use it under the supervision of an adult Ensure that those present are aware of possible hazards e g movable parts during training The resistance level can be adjusted to your personal preference Do notuse the bike without shoes or loose shoes Ensure that sufficient space is available to use the bike Be aware of non fixed or moving parts whilst mounting or dismounting the bike To protect the floor or carpet from damage place a mat under the ex
5. ercise Bike In case of emergency please place both feet at the same time on the side reins Ensure that an area of 2000 x 1000 mm behind the exercise Bike is free from any obstacles This product is tested up to a maximum body weight of 120 kilograms We take no responsibility for personal injury or damage sustained by or through the use of this exercise Bike Assembly Drawing Step one Attach the front 16 and rear feet 12 to the frame using the nuts 8 washer 9 and bolts 10 Step two Attach the handlebar post 23 by inserting it into the head tube on the frame Use the knob to adjust and tighten the height to the desired position Attach the handlebar slider 21 on the handlebar post 23 use release lever 22 to adjust and tighten the handlebar into position Step three Insert the seat post 42 into the seat tube on the frame Attach the saddle 1 into seat slider 41 then tighten the screw of saddle Insert the seat slider 41 into the seat post 42 and fix Using knob 4 adjusts and tightens the height in the desired position Step four Attach the pedals 11 into the crank arms 7 5 each pedal is marked with L left or R right to denote the side of the spinning bike they are on Note the right hand crank is on the same side as the chain guard 24 Be careful to align the threads correctly to avoid damaging them Applying a little grease on the threads will help the pedals to screw in easi
6. ly and correctly tighten using a 15mm spanner both pedals should tighten towards the front of the spinning bike Adjusting the resistance Adjust the exercise resistance on the spinning bike using the brake knob 31 to loosen or tighten The flywheel should rotate freely without resistance when you loosen the brake system fully More experienced riders may wish to increase the overall resistance by tightening the brake system Exploded Drawing N L T a A 15 Part list 6 1 Saddle 1 PC 25 Flywheel axle 2 Alloy bind clamp R L 3 PC 26 Flywheel security washer 1 SET 3 Knob spring 3 PC 27 Flywheel bearing 4 Knob 3 PC 28 BB axle w plate 1 PC 5 Left crank arm 1 PC 29 Bottle cage 1 PC 6 Belt 1 PC 30 Screw for bottle cage 2 PCS 7 Right crank arm 1PC 31 Brake system 1 SET 8 Foot tube nut 4PCS 32 Crank bolt 2 PCS 9 Foot tube washer 4PCS 33 Flywheel security nut 2 PCS 10 Foot fixing bolt 4PCS 34 Outer chain guard bolt M6 2PCS 11 Pedal LPR 35 Bolt and washer for spring 2 PCS bracket 12 Rear foot tube 1PC 36 Flywheel adjuster bolt 2 PCS 13 Front foot end cap 2PCS 37 Knob washer 3 PCS 14 Rear foot end cap Se 38 Knob plastic washer 3 PCS 15 Rear foot adjuster wheel 39 Knob fixed bolt 3 PCS 16 Front foot tube 1 PC 40 Washer 3 PCS 17 Brake pad 41 Seat slider 1 PC 18 Brake pad holder due
Download Pdf Manuals
Related Search