LITE For first time use, follow the instructions below
Contents
1. the RF frames sent by the sensors dashes will be displayed instead of pressure temperature value If the problem is permanent please contact your distributor FIG 14 WHEEL UNIT SENSOR LOW BATTERY ALERT The pressure information blinks alternately with Lo symbol to inform you that the sensor must be replaced Ask your distributor Note In winter conditions do not care about this message below 8 C external temperature G HOW TO FIX YOUR DISPLAY FIG 15 HANDLE BAR FIXING blocked COPYRIGHTS LDL TECHNOLOGY JULY 2009 5 7 Put the display to the selected place on the handle bar and fix it with the screw kit n 12 Then clip the display and place the CPA n 8 The tab that allows you to remove the display is now YURE LDE YiL LITE TIRE PRESSURE MONITORING SYSTEM FIG 16 BODY MOTOR FIXING First drill the body and fix the base clipbody base with the screw kit n 13 Then clip the display and place the CPA n 8 The tab that allows you to remove the display is now blocked FIG 17 BRACELET FIXING Make the bracelet run through the planned slots of the 2 clipboby horizontally or vertically by introducing it from FIG 18 STEERING COLUMN FIXING from 212 to 216mm an angle Then pull it strongly by using pliers Clip the display Do not put the CPA with bracelet Insert the screw into the clipbody central hole screw kit n 14 Then place the compressible brace and the nut on the s2. European Union Directives Conformity Products marked CE are in compliance with Directive R amp TTE 99 5 EC Products marked FCC are in compliance with Directive FCC part 15 Using precautions Never fix directly on a metal part you may loose signal Do not wash directly with a jet of water ex karcher TIRE WATCH is only rain proof Avoid prolonged sun exposition when you don t use it Do not repair the device by your own you may loose warranty The internal components reparation must be done by qualified technician or recognized repairing centre Never use solvent only wash TIRE WATCH with water soap and sweet cloth f you drive close to electromagnetic disturbance military base embassy you may loose temporary the signal Warranty one year by presenting your bill and the warranty card filled out and stamped by your motor dealership LDL Technology reserves the right to modify its product and to bring any modification without preliminary notice COPYRIGHTS LDL TECHNOLOGY JULY 2009 7 7
3. PRESSURE THRESHOLD CROSSING ALERT When the display receives lower pressure information compared to the programmed thresholds Pmin the alert starts during the first 3 minutes led blinks in alternance with bar symbol arrow of the faulty tire then bar and arrow symbol will flash until new tire inflation backlight on during 3 minutes to see the alert at night drivings To display tire temperature during alert short push on The display will return automatically to pressure alert after 10 seconds FIG 11 TEMPERATURE THRESHOLD CROSSING ALERT A high temperature threshold is programmed at 80 C for front tire and 90 C for rear tire and cannot be changed When the display receives upper pressure oman omoare to the programmed thresholds the alert starts C symbol arrow of the faulty tire are flashing until the tire comes to a lower value than the programmed threshold To display tire pressure during alert gt short push on The display will return automatically to temperature alert after 10 seconds Note Pressure alert has priority even if temperature alert is active COPYRIGHTS LDL TECHNOLOGY JULY 2009 4 7 YURE LDE Walami LITE TIRE PRESSURE MONITORING SYSTEM FIG 12 LOW BATTERY DISPLAY ALERT Battery symbol is blinking to inform you that you have to change the battery of the display PANASONIC OR MAXELL CR2450 only FIG 13 NON PERMANENT LOSS OF COMMUNICATION In case the receiver does not receive
4. TTON FUNCTIONS ON Scrolling menus Validation Backlight only nash gosean gt 2 Bt ON OFF Display Units Setting Swap from Pressure to Temperature backlight 4 seconds Tire Pressure or Temperature information Pressure bar PSI or Temperature unit C External temperature NB Due to the waterproof nature of the housing stabilisation of the temperature reading may take several minutes 24 Hour Clock Note Permanent back light function to activate the permanent back light press tand simultaneously Do the same to turn off the permanent back light The permanent use of the back light uses excessive battery life so its usage is recommended at night only COPYRIGHTS LDL TECHNOLOGY JULY 2009 1 7 YURE LDE Walami LITE TIRE PRESSURE MONITORING SYSTEM C KIT COMPOSITION 8 5 11 5 2d rmi sual 1 display button battery CR2450 2 wheel unit sensors with 11 5XL nut and spring 2 valves 2 specific seals for some BMW rims see specificities 2 seals for 8 5mm valve hole 2 nuts for 8 5mm valve hole see specificities 1 peg for valve in spoke see specificities 1 connector position assurance CPA 1 clipbar O 1 clipbody 1 bracelet 1 handle bar screws kit 1 M5x20 screw 1M5 self locking nut 1 sleeve 1 motor body screw kit 2 M3 screws 2 M3 nuts 2 washers 1 steering column screw kit 1 compressible brace 1 M5x40 sc
5. YURE LUDE Walami LITE TIRE PRESSURE MONITORING SYSTEM TIRE WATCH FOR MOTORCYCLE USER MANUAL Thank you for purchasing this TIRE WATCH system TIRE WATCH will allow you to drive with more confidence and be alerted in the event of a slow leak or puncture The setup options for the TIRE WATCH system are detailed below For first time use follow the instructions below You may not set the system values as detailed in section C until the following sensor allocation is completed A FIRST USE OF THE DISPLAY FIG 9 MENU 06 FRONT amp REAR TIRE IDENTIFIER ID ALLOCATION The first time the display is powered up it has to verify the unique ID of the front and rear tire the unique ID s are pre programmed during manufacture not allocated to a position and have to be confirmed now to the display Turn ON the display gt short push on tor ID symbols are blinking Drive faster than 20 Mph until Pressure value displayed time out 4mn To invert the front and rear wheel unit sensor allocation gt FIG 8 MENU 05 VALUE INVERSION If this learning phase fails dashes will be displayed instead pressure values Then you will have to start again the ID confirmation process Switch off the display and wait 8 minutes motorcycle stopped before repeating this phase If the pressure values are not displayed after several trials please contact your dealer B KNOW EVERYTHING ABOUT YOUR EQUIPMENT FIG 1 DISPLAY BU
6. crew and put it on the steering column tube Screw until the clipbody is correctly fixed NB do not exceed 2Nm Put in place the CPA n 8 COPYRIGHTS LDL TECHNOLOGY JULY 2009 6 7 YURE LUDE Walami LITE TIRE PRESSURE MONITORING SYSTEM FIG 19 CHANGE THE BATTERY FROM THE DISPLAY Unscrew the battery cover situated on the back of the display using a five euros cents coin Replace the used battery with a new one CR2450 PANASONIC or MAXELL only as illustrated and screw again the battery cover Please check that the seal is correctly in place FIG 20 REMINDER FOR MOTOR DEALERSHIP FOR WHEEL UNIT SENSORS MOUNTING Screw the nut with a 5mm allen key Do not exceed 2 rounds per second and hold the valve while screwing to prevent it from turning around A Final torque 4 2Nm 0 2Nm The sensor must not get in touch with the tire during the mounting process H SAFETY AND GENERAL INFORMATION Users are not permitted to proceed any changes or modify the device in any way TIRE WATCH has an information goal that does not replace the inflation phases under the initiative and entire responsibility of the pilot Tire pressure has to be done according to manufacturer recommendations always inflate your tire cold 23 C If the inflation process takes less than 6 min after driving the information will be updated every 5 seconds Should the opposite occur the information will be updated while driving USA Canada and
7. ress on To access the next menu G Note Temperature unit is fixed to C FIG 6 MENU 03 FRONT amp REAR LOW TIRE PRESSURE THRESHOLD SETTING Setting range for front values 1 4 bar to 3 5 bar 20 to 51 PSI Minimum alert pressure Pmin LO pre programmed at 1 8 bar 26 PSI Set the Pmin LO values for front tire FIG 7 MENU 04 REAR LOW TIRE PRESSURE THRESHOLD SETTING Setting range for rear values 1 4 bar to 3 5 bar 20 to 51 PSI Minimum alert pressure Pmin LO pre programmed at 1 8 bar 26 PSI Set the Pmin LO values for rear tire COPYRIGHTS LDL TECHNOLOGY JULY 2009 3 7 YURE LUDE YiL LITE TIRE PRESSURE MONITORING SYSTEM FIG 8 MENU 05 VALUE INVERSION FIG 8 In case of values inversion during the learning phase in general front pressure is the lowest value you can invert them Reach FIG 7 by an extended push on Then push shortly on To validate gt short push on E ALLOCATE YOUR WHEEL UNIT SENSORS Process to follow when you change one or two wheel unit sensors OR when the first learning phase has failed FIG 9 MENU 06 ID RECOGNITION A During all the learning process tires must at least be inflated at 1 bar From ON gt extended push on 8tuntil FIG 8 is reached To launch ID learning gt short push on D ID symbols are blinking Drive faster than 20 Mph until Pressure values are displayed time out 4mn F RECOGNIZE THE DIFFERENT ALERT MODES FIG 10
8. rew 1 M5 nut with washer FIG 2 TURN THE DISPLAY ON AND OFF ON gt short push on or temperature displayed after 10s The display is waiting for Ids reception OFF gt long push on or automatically turn off after 6mn caused by no wheel unit sensor transmission FIG 3 CHANGING THE DISPLAYED MODE Pressure is the standard display mode To_ display Temperature gt short push on To return to the pressure display push again shortly on COPYRIGHTS LDL TECHNOLOGY JULY 2009 2 7 YURE LUDE valam LITE TIRE PRESSURE MONITORING SYSTEM C SET YOUR VALUES amp ALARM SETTINGS Proceed to the scrolling menu gt long push on Bt 1 Once the wanted menu is reached gt the first digit is blinking to inform you that you enter the menu to set the 1 digit gt short push on Bt2 until the wanted value is reached To validate the 1 digit and set the 2 digit gt short push on Bt 1 Repeat the operation until the last digit To validate the last digit and the on going menu short push on Bt 1 To accede on the following menu short push on Bt 1 To go back to the standard mode FIG 3 gt long push on Bt 1 D SET YOUR VALUES BY USING THE UNROLLING MENU FIG 4 MENU 01 HOUR SETTING Adjust your values as described in chapter C FIG 5 MENU 02 PRESSURE UNIT CHOICE Standard unit is Bar to swap in PSI Short push on to swap again to bar unit press again on To validate your unit choice p
Download Pdf Manuals
Related Search