USER MANUAL - Kramer Electronics Japan Homepage
Contents
1. Figure 4 Typical Video Distribution KRAMER ELECTRONICS LTD KRAMER 6 2 6 3 Increasing the Number of Outputs To increase the number of outputs the audio video distribution amplifiers described in this manual can be linked by setting up a cascaded configuration It is not recommended to cascade more than two machines An example is set below how to get an additional output when cascading two PT102A Perform the following steps 1 Connect an audio source to the INPUT connector of the first PT102A 2 Connect one acceptor to the OUT1 connectors of the first PT102A 3 Connect an audio cable from the OUT2 connector of the first PT102A to the INPUT connector of the cascaded PT102A 4 Connect up to two audio acceptors to the OUTPUT connectors of the cascaded PT102A 5 Operate the distribution amplifiers source and acceptors 6 Use the R L GAIN trimmers to control the left right audio levels Increasing the Number of Inputs When it is necessary to handle more than one input a video switcher such as the 4x1 VB or a bigger one such as the 801xl can be used to select the required input to be switched to the outputs The 4x1 VB for example can be serially connected between the video sources and the distribution amplifier for video switching It is designed for composite video signals using BNC connectors accepts up to four inputs and allows the user to select any input to be routed to one output using buttons located on th2. Distribution Amplifiers Video Audio Distribution Amplifiers described in this manual distribute one signal to several users They vary in the number of outputs operating format and bandwidth Video Audio distribution amplifiers are used to distribute one source to several acceptors monitors audio devices etc for simultaneous recording or monitoring of one source with no discernible signal degradation A good quality distributor amplifies the incoming signal pre compensates the signal for potential losses resulting from the use of long cables noisy sources etc and generates several identical buffered and amplified outputs Often a signal processor is inserted between the source and the distribution amplifier for correction and fine tuning of the source signal before multiplication so that all copies are corrected in the same way Typical applications of the machines are audio video duplication studios delivering undiminished quality duplicates and video showrooms delivering an identical signal to several acceptors The front panels of these Kramer distribution amplifiers are designed to be simple to operate Factors Affecting Quality of Results There are many factors affecting the quality of results when signals are transmitted from a source to an acceptor gt Connection cables Low quality cables are susceptible to interference they degrade signal quality due to poor matching and cause elevated noise levels They should therefore be
3. on BNC on 3 5mm mini phone connectors 0 3 Vpp 75Q C on 4P connectors connectors Level Control 50 to 18 8 dB 2 to 5 dB Y GAIN 0 7 to 2 3 dB Gain 2 to 5 dB C GAIN 0 to 2 2 dB EQ 4 43 MHz Input Output A AC AC Coupling Bandwidth 100 kHz 3dB 150 MHz 3dB Y 430 MHz 3dB Differential Gain lt 0 03 Y lt 0 16 C Differential Phase 0 03 Deg 0 11 Deg S N Ratio 74 dB 71 6 dB Y 78 dB Max Output 5 2 Vpp 150 Q 2Vpp 75 Q Y 2Vpp 75 Q Level Audio lt 0 017 NA NA THD Noise Accessories Power supply mounting Power supply mounting Power supply mounting bracket bracket bracket Options Model VA 50P rack Model VA 50P rack Model VA 50P rack mountable power supply with mountable power supply with mountable power supply with six 12VDC outlets six 12VDC outlets six 12VDC outlets Dimensions 6 5 cm X 6 cm X 2 5 cm 6 5 cm X 6 cm X 2 5 cm 6 5 cm X 6 cm X 2 5 cm W D H 2 55 X 2 36 X 1 W D 2 55 X 2 36 X 1 W D 2 55 X 2 36 X 1 W D H H H 0 14 Kg 0 31 Lbs Approx 0 14 Kg 0 31 Lbs Approx 0 14 Kg 0 31 Lbs Approx Power Source 12VDC 30mA use current 12VDC 30mA use current 12VDC 30mA use current limited power supply limited power supply limited power supply KRAMER ELECTRONICS LTD KRAMER 3 4 1 HOW DO I GET STARTED The fastest way to get started is to take your time and do everything right the first time Taking 15 minutes to read the manual may
4. save you a few hours later You don t even have to read the whole manual If a section doesn t apply to you you don t have to spend your time reading it UNPACKING AND CONTENTS The items contained in your Kramer distribution amplifier package are listed below Please save the original box and packaging materials for possible future shipment Distribution Amplifier Kramer Concise Product Catalog Power Supply 12VDC Mounting Brackets User Manual 4 Rubber Feet Optional Accessories The following accessories which are available from Kramer can enhance implementation of your distribution amplifier For information regarding cables and additional accessories contact your Kramer dealer gt Rack Adapter Used to install smaller machines in a standard 1U rack One or more machines may be installed on each adapter gt BNC Y Connector Used for looping purposes and splits the incoming signal to enable connection of an additional machine gt SP 11 Video Audio Processor can be serially connected between the video audio source and the distribution amplifier for video and audio control correction The machine provides camera control and luminance white balance correction The SP 11 is also capable of performing composite to Y C conversion and bi directional transcoding The machine allows full control over the video signal video gain down to full fade log or linear definition control log or linear cont
5. KRAMER KRAMER ELECTRONICS Ltd USER MANUAL Kramer Distribution Amplifiers PICO TOOL Models PT102A PT102S PT102V IMPORTANT Before proceeding please read paragraph entitled Unpacking and Contents KRAMER Section 1 1 1 1 2 2 3 4 4 1 5 5 1 5 2 5 3 6 6 1 6 2 6 3 7 8 9 9 1 9 2 9 3 9 4 9 5 10 11 11 1 11 2 11 3 Figure AUNE Table Table Of Contents Name INTRODUCTION A Word on Video Audio Distribution Amplifiers Factors Affecting Quality of Results SPECIFICATIONS HOW DO I GET STARTED UNPACKING AND CONTENTS Optional Accessories VIDEO AUDIO DISTRIBUTION AMPLIFIERS Getting to Know Your PT102A Distribution Amplifier Getting to Know Your PT102S Distribution Amplifier Getting to Know Your PT102V Distribution Amplifier TYPICAL APPLICATIONS Typical Video Distribution Increasing the Number of Outputs Increasing the Number of Inputs CONNECTING TO VIDEO DEVICES CONNECTING TO AUDIO DEVICES USING THE MACHINES Turning on the Machine Gain and EQ Control PT102V only Luma Control PT102S only Chroma Control PT102S only Audio Level Control PT102A TAKING CARE OF YOUR MACHINE TROUBLESHOOTING Power and Indicators Video Signal Audio Signal Limited Warranty List Of Illustrations PT102A Panel Features PT102S Panel Features PT102V Panel Features Typical Video Distribution Increasing the Number of Inputs List Of Tables PT102A Panel Features PT102S Pane
6. as monitors projectors or recorders may be connected to the PICO TOOLS through the BNC type connectors PT102V or through the 4P connectors PT102S located on the back of the unit If you use separate Y and C cables for the distribution of s Video the cables must be of equal lengths The signals supported by the various models are composite and S video signals CONNECTING TO AUDIO DEVICES Audio sources and output devices such as amplifiers or recorders may be connected to the PICO TOOLS through the 3 5mm mini phone type connectors PT102A located at the back of the machine The signals supported are Stereo Audio and Balanced Mono USING THE MACHINES 9 1 Turning on the Machine 9 2 9 3 9 4 9 5 NOTES 1 The machine should only be turned on after all connections are completed and all source devices have been turned on Do not attempt to connect or disconnect any video or audio signals to the machine while it is turned on 2 The socket outlet should be near the equipment and should be easily accessible To fully disconnect equipment remove the power supply adapter from the mains socket 1 Connect the machine s DC socket to the power supply provided with the machine Observe proper polarity Observe that the LED on the panel is illuminated 2 Operate the source and the acceptors Gain and EQ Control PT102V only The Gain Control function enables the operator to adjust the picture intensity level and compensate for
7. c operation or failure Do not locate your machine where temperature and humidity may be excessive Doing so may also damage the electronics and cause erratic operation or failure of your machine Do not clean your machine with abrasives or strong cleaners Doing so may remove or damage the finish or may allow moisture to build up Take care not to allow dust or particles to build up inside unused or open connectors 11 TROUBLESHOOTING NOTES 1 Please note that if the output signal is disturbed or interrupted by very strong external electromagnetic interference it should return and stabilize when such interference ends If not disconnect power from the machine and reconnect again to reset the machine 2 If the following recommended actions still do not result in satisfactory operation please consult your KRAMER Dealer 11 1 Power and Indicators 11 2 Video Signal No video at the output device regardless of input selected Video level is too high or too dim KRAMER ELECTRONICS LTD Confirm that power connections are secured at the machine and at the receptacle Make sure the receptacle is active outputting the proper voltage If there is still no power use a Philips screwdriver to remove screws on both sides of the machine and remove the panel Locate fuse inside your machine The fuse looks like a little jumper If necessary replace fuse with another with the same rating Install cover by replacing the Phili
8. d by the warranty 1 Any product which is not distributed by Kramer or which is not purchased from an authorized Kramer dealer If you are uncertain as to whether a dealer is authorized please contact Kramer at one of the agents listed in the web site www kramerelectronics com 2 Any product on which the serial number has been defaced modified or removed 3 Damage deterioration or malfunction resulting from a Accident misuse abuse neglect fire water lightning or other acts of nature b Unauthorized product modification or failure to follow instructions supplied with the product c Repair or attempted repair by anyone not authorized by Kramer d Any shipment of the product claims must be presented to the carrier e Removal or installation of the product f Any other cause which does not relate to a product defect g Cartons equipment enclosures cables or accessories used in conjunction with the product WHAT WE WILL PAY FOR AND WHAT WE WILL NOT PAY FOR We will pay labor and material expenses for covered items We will not pay for the following 1 Removal or installations charges 2 Costs of initial technical adjustments set up including adjustment of user controls or programming These costs are the responsibility of the Kramer dealer from whom the product was purchased 3 Shipping charges HOW YOU CAN GET WARRANTY SERVICE 1 To obtain service on you product you must take or ship it prepaid to any authori
9. e side panel A typical switching configuration is described below where one of four video inputs is selected by a 4x1 VB switcher and then outputted to a PT102V input To extend the number of switcher outputs up to two acceptors can be connected to the PT102V for video distribution of the selected input Perform the following steps 1 Connect up to four video sources to the IN1 IN4 BNC connectors of the 4x1 VB 2 Connect a cable from the OUTPUT connector of the 4x1 VB to the INPUT connector of the PT102V 3 Connect up to two video acceptors to the output connectors of the PT102V 4 Use the INPUT SELECTOR switches of the 4x1 VB to select the desired input to be switched 5 Operate the 4x1 VB PT102V sources and acceptors 6 DO NOT USE the GAIN and EQ trimmers of the PT102V to control the level of the output signal unless it is absolutely necessary Please see the note at the beginning of this chapter Video Sources Up to 2 Video Acceptors T AAAA OUT 2 OUT 1 INPUT OUTPUT IN1 IN2 IN3 IN4 KRAMER TOOLS Pico TOCLS KRAMER 1 2 Video DA KRAMER 4x1 High Resolution Video Switcher 4x1VB PT1 o2v INPUT SELECTOR GAN EQ ON t2voc F IN1 IN2 IN3 IN4 A ENEE Figure 5 Increasing the Number of Inputs KRAMER ELECTRONICS LTD KRAMER 7 9 CONNECTING TO VIDEO DEVICES Video sources and output devices such
10. ect all interconnect cables and reconnect them one at a time until ground loop reappears Disconnect the affected cable and replace or insert an isolation transformer in the signal path Confirm that your sources and output device are turned on and connected properly Audio signals connected to the input of your machine should be properly wired to the output of your source Audio signals connected to the output of your machine should be properly wired to the input of your machine or recorder Confirm that any other amplifiers in the signal path have the proper input and or output selected Pay special attention to input amplifiers that may be built into your acceptor Confirm that the connecting cables are of high quality and properly built Take special care in noting the wiring configuration of balanced to unbalanced cables Check level controls located on your source input device or output display or recorder 12 KRAMER LIMITED WARRANTY Kramer Electronics hereafter Kramer warrants this product to be free from defects in material and workmanship under the following terms HOW LONG IS THE WARRANTY Labor and parts are warranted for three years from the date of the first customer purchase WHO IS PROTECTED Only the first purchase customer may enforce this warranty WHAT IS COVERED AND WHAT IS NOT COVERED Except as below this warranty covers all defects in material or workmanship in this product The following are not covere
11. l Features PT102V Panel Features KRAMER ELECTRONICS LTD Page CAAYDMMNAHHHRWNNNY e e e e e e o e e o e e a a a Lea e a T a a a a A EI E a a ae G a E a E a a Page OoN Page KRAMER 1 1 1 1 2 INTRODUCTION Congratulations on your purchase of this Kramer Electronics Distribution Amplifier Since 1981 Kramer has been dedicated to the development and manufacture of high quality video audio equipment The Kramer line has become an integral part of many of the best production and presentation facilities around the world In recent years Kramer has redesigned and upgraded most of the line making the best even better Kramer s line of professional video audio electronics is one of the most versatile and complete available and is a true leader in terms of quality workmanship price performance ratio and innovation In addition to the Kramer line of high quality distribution amplifiers such as the one you have just purchased Kramer also offers a full line of high quality switchers processors interfaces controllers and computer related products This manual includes configuration operation and option information for the following products from the Kramer line of distribution amplifier PICO TOOLS All these PICO TOOLS are similar in operation and features gt PT102A 1 2 Audio Distribution Amplifier gt PT102S 1 2 s Video Distribution Amplifier gt PT102V 1 2 Video Distribution Amplifier A Word on Video Audio
12. losses caused by cables which are too long or non standard The EQ Control pre compensates for cable losses The control trimmers should be used only if you are absolutely sure that the problem arises from the cables or connectors Unnecessary use of those trimmers will upset the factory adjustments and the 1 1 signal transparency will be lost Luma Control PT102S only The Luma Level control should be treated similarly to the Video Gain control described above Unnecessary adjustments will upset the 1 1 signal transparency Equalization problems that occur due to long or non standard cables resulting in fine detail loss may be further compensated by using the Kramer VM 9YC Y Equalization Control function Chroma Control PT102S only The Chroma Level control should be treated similarly to the Video Gain control described above Unnecessary adjustments will upset the 1 1 signal transparency Problems that occur due to long or non standard cables resulting in color distortion problems may be further compensated by using the Kramer VM 9YC Chroma Equalization Control functions Audio Level Control PT102A To adjust the audio level simply adjust the L R audio level trimmers until a satisfactory audio level is achieved KRAMER ELECTRONICS LTD 10 KRAMER 10 TAKING CARE OF YOUR MACHINE Do not locate your machine in an environment where it is susceptible to dust or moisture Both of these may damage the electronics and cause errati
13. ntirely passive design of the 4x1VB eliminates the need for a power supply Unselected inputs are automatically terminated into a 75ohm resistor The 4x1VB is part of the Kramer TOOLS family of compact high quality cost effective solutions for a variety of applications gt VS 801xl 8x1 Composite Single Component Video amp Unbalanced Audio Switcher allows several video audio sources to be connected to its inputs for switching The machine provides truly effortless switching between eight video unbalanced audio inputs and one output Switching is done during vertical interval either of source no 1 or of the video available on the external sync socket The switcher may be controlled by touch buttons or by contact closure via a remote socket on the back of the machine Video signal bandwidth is 225MHz typical allowing the machine to be used in the most demanding applications gt VIDEO TESTER A new unique patented indispensable tool for the video professional the Video Tester is used to test a video path leading to from an amplifier By pressing only one touch switch it can trace missing signals distinguish between good and jittery VCR sourced signals and identify the presence of good signals Whenever a video signal is missing because of bad connections cable breaks or faulty sources the Video Tester is all you need KRAMER ELECTRONICS LTD KRAMER 5 VIDEO AUDIO DISTRIBUTION AMPLIFIERS This section describes all the co
14. ntrols and connections of your distributor Understanding all of the controls and connections helps you realize the full power of your distribution amplifier 5 1 Getting to Know Your PT102A Distribution Amplifier The Kramer PT102A is a high performance 1 2 distribution amplifier for stereo audio signals It accepts a single input and distributes it to two identical outputs using 3 5mm mini jacks Separate left and right gain controls allow the user to optimize signal levels The PT102A is typically used for unbalanced stereo audio sources such as VCR s portable cassette and CD players computer sound cards etc but can also distribute a balanced mono signal using readily available adapter cables It is also the ideal companion to video Pico TOOLS such as the PT102V and PT102S A 12V power supply is provided The PT102A is part of the new Kramer Pico TOOLS family of products for applications requiring uncompromising quality and compact size at an affordable price Panel features of the PT102A are described in Figure 1 and Table 1 NOTE For operation instructions refer to section 10 OUT2 OUT 1 VOCLS ag 1 2 Audio DA KRAMER PT102A LGAIN RGAIN ON 12v Dc Pot OOO Figure 1 PT102A Panel Features Table 1 PT102A Panel Features e onimo Glows when powerisapplied SSCS KRAMER ELECTRONICS LTD KRAMER 5 2 Getting to Know Your PT102S Distribution Amplifier The Kramer PT102S is a high performance 1 2 dist
15. of the best quality gt Sockets and connectors of the sources and acceptors So often ignored they should be of highest quality since Zero Ohm connection resistance is the objective Sockets and connectors also must match the required impedance 75ohm in video Cheap low quality connectors tend to rust thus causing breaks in the signal path gt Amplifying circuitry Must have quality performance when the desired result is high linearity low distortion and low noise operation gt Distance between sources and acceptors Plays a major role in the final result For long distances over 15 meters between sources and acceptors special measures should be taken in order to avoid cable losses These include using higher quality cables or adding line amplifiers gt Interference from neighboring electrical appliances These can have an adverse effect on signal quality Balanced audio lines are less prone to interference but unbalanced audio should be installed far from any mains power cables electric motors transmitters etc even when the cables are shielded KRAMER ELECTRONICS LTD KRAMER 2 SPECIFICATIONS PF PT102A PT102S PT102V 1 2 Audio DA 1 2 s Video DA 1 2 Video DA 1 Stereo Audio 1 Vpp 20k on 1 s Video 0 7Vpp 75Q Y 1 Video 1Vpp 75Q ona a 3 5mm mini phone connector 0 3Vpp 75Q C on a 4P BNC connector connector Outputs 2 Stereo Audio 1 Vpp 150 Q 2 s Video 0 7Vpp 75Q Y 2 Video 1 Vpp 75Q
16. ps screws Confirm that your source and output devices are turned on and connected properly The input of your machine should be of an identical signal format at the output of your source Signals at the output of your machine should be of an identical signal format as at the input of your display Confirm that any other device in the signal path have the proper input and or output selected Use the Video Tester to test the video path leading to from your machine see section 4 1 Video Tester Verify that the lines are well matched through 75ohm impedances Confirm that the connecting cables are of high quality and properly inserted Check level controls located on your source input device or output display 11 KRAMER Noise bars are rolling up or down in the output image or Low Frequency Hum in the output signal 11 3 Audio Signal No audio at the output device regardless of input selected Audio level is too low KRAMER ELECTRONICS LTD Hum bars ground loop are caused by a difference in the ground potential of any two or more devices connected to your signal path WARNING Do not disconnect the ground from any piece of video equipment in your signal path Check the following to remove hum bars Confirm that all interconnected equipment is connected to the same phase of power if possible Remove equipment connected to that phase that may introduce noise such as motors generators etc Disconn
17. rast control color saturation control black level control red green and blue controls and a screen splitter control for before after comparison The Input switch control is audio follow video gt 104L Video Line Amplifier can be serially connected between the video source and the distribution amplifier for video line amplification and cable compensation video field work and SDI signal distribution Signal loss and the resulting depreciation in picture quality is a real problem in any video setup requiring considerable distance between video source and acceptors The 104L video line amplifier one of the KRAMER TOOLS is a high quality amplifier which prevents video signal losses over long cables For best results the 104L amplifier is installed adjacent to the video source The 104L is housed in the compact KRAMER TOOLS enclosure and is fed by a 12VDC source High bandwidth and front accessible controls make it suitable for the most demanding analog and SDI studio applications gt 4x1VB 4x1 mechanical switcher can be serially connected between the composite video sources and the distribution amplifier for video switching It is designed for composite video signals using BNC connectors It accepts up to four inputs and allows the user to select any input to be routed to one output using buttons located on the side panel High quality switching components are used to ensure minimal crosstalk and very high bandwidth The e
18. ribed in Figure 3 and Table 3 NOTE For operation instructions refer to section 10 O OUT 2 OUT 1 INPUT TOCLS ag 1 2 Video DA KRAMER PT102V GAIN EQ ON 12VDC CH 0000 Figure 3 PT102V Panel Features Table 3 PT102V Panel Features Pe ONE i ee o KRAMER ELECTRONICS LTD KRAMER 6 TYPICAL APPLICATIONS IMPORTANT NOTE The built in trimmers were factory pre adjusted to assure 1 1 transparent operation Readjusting the trimmers by the user can upset this transparency 6 1 Typical Video Distribution Figure 4 illustrates a typical setup of one of the distribution amplifiers described in this manual An incoming single input from a source VCR is split into two identical outputs and connected to acceptors Perform the following steps as necessary 1 Connect the output of the video source to the video INPUT connector of the distribution amplifier PT102V in this case 2 Connect the OUTPUTS of the PT102V to the inputs of up to two video acceptors 3 Operate the source acceptors and the PT102V 4 Use only if necessary the GAIN and EQ trimmers to control the gain and cable Equalization of the video outputs see section 11 2 for more details Recording VCR or Monitor Recording VCR or Monitor Playing VCR OUT 2 OUT 1 INPUT Aigo TOLE 1 2 Video DA KRAMER PT102V 12 DC Power Supply Adjust if necessary i Gain and EQ Controls GAIN EQ ON 12vDcC O
19. ribution amplifier for s Video Y C signals It accepts a single input and distributes it to two identical outputs using 4 pin connectors Video bandwidth of 150MHz ensures that the PT102S remains transparent even in the most critical applications It is the ideal companion to the PT102A audio Pico TOOL A 12V power supply is included The PT102S is part of the new Kramer Pico TOOLS family of products for applications requiring uncompromising quality and compact size at an affordable price Panel features of the PT102S are described in Figure 2 and Table 2 NOTE For operation instructions refer to section 10 1 2 s Video DA KRAMER PT102S CGAIN YGAIN ON 12v Dc 0000 Figure 2 PT102S Panel Features Table 2 PT102S Panel Features Pe m i eee o KRAMER ELECTRONICS LTD KRAMER 5 3 Getting to Know Your PT102V Distribution Amplifier The Kramer PT102V is a high performance 1 2 distribution amplifier for composite video signals It accepts a single input and distributes it to two identical outputs using BNC connectors Video bandwidth of 430MHz ensures that the PT102V remains transparent even in the most critical applications It is the ideal companion to the model PT102A audio Pico TOOL A 12V power supply is included The PT102V is part of the new Kramer Pico TOOLS family of products for applications requiring uncompromising quality and compact size at an affordable price Panel features of the PT102V are desc
20. roval This may be obtained from your dealer NOTICE This equipment has been tested to determine compliance with the requirements of EN 50081 Electromagnetic compatibility EMC generic emission standard Part 1 Residential commercial and light industry EN 50082 Electromagnetic compatibility EMC generic immunity standard Part 1 Residential commercial and light industry environment CFR 47 FCC Rules and Regulations Part 15 Radio frequency devices Subpart B Unintentional radiators CAUTION gt Servicing of the above mentioned machines is only allowed to a Kramer authorized technician or Engineer Any user who makes changes or modifications to the unit without the express approval of the manufacturer will void user authority to operate the equipment Use the DC power supply provided to supply power to the machine and controllers Please use recommended interconnect cables to connect the machine to controllers and other components KRAMER ELECTRONICS LTD 14 KRAMER KRAMER The list of Kramer distributors appears on our web site www kramerelectronics com From the web site it is also possible to e mail factory headquarters We welcome your questions comments and feedback KRAMER ELECTRONICS LTD 3 Am VeOlamo Street Jerusalem 95463 Israel Tel 972 2 654 4000 Fax 972 2 653 5369 e mail kramerel netvision net il
21. zed Kramer service center 2 Whenever warranty service is required the original dated invoice or a copy must be presented as proof of warranty coverage and should be included in any shipment of the product Please also include in any mailing a contact name company address and a description of the problem s 3 For the name of the nearest Kramer authorized service center consult your authorized dealer KRAMER ELECTRONICS LTD 13 KRAMER LIMITATION OF IMPLIED WARRANTIES All implied warranties including warranties of merchantability and fitness for a particular purpose are limited in duration to the length of this warranty EXCLUSION OF DAMAGES Kramer s liability for any defective products is limited to the repair or replacement of the product at our option Kramer shall not be liable for 1 Damage to other property caused by defects in this product damages based upon inconvenience loss of use of the product loss of time commercial loss or 2 Any other damages whether incidental consequential or otherwise Some countries may not allow limitations on how long an implied warranty lasts and or do not allow the exclusion or limitation of incidental or consequential damages so the above limitations and exclusions may not apply to you This warranty gives you specific legal rights and you may also have other rights which vary from place to place NOTE All products returned to Kramer for service must have prior app
Download Pdf Manuals
Related Search