User Manual
Contents
1. User Manual DUO deaniri Laser show System IVC FSC PROFESSIONAL PRODUCTS Thank you for purchasing the DUO BEAM RG Laser Show System This manual is intended to help you to use the functions of the unit It is suggested that you should refer to this instruction manual before operating the DUO BEAM RG Features of the product Class Illb Laser show product Red Diode Laser module up to 60mW D650nm Green Diode Pumped Solid State lasers up to 50 gt mW 532nm Built in high speed stepping motor Real time calculating unit to generate patterns Sound Active operation for scan and pattern changes 48 pre programmed laser sequences Compatible with standard DMX512 signal The use of fog will enhance the aerial effect of this unit Input power AC 120V 60Hz Power consumption Max 50VA Operation temperature Operation temp 20 85 C storage 20 C 80 humidity no condensation Measure 300mmx100mmx180mm Weight 3 6kg The rear panel view Installation 1 Carefully inspect your Laser Show equipment as you unpack it If any damage is evident such as dents or scratches on the covers or broken knobs etc immediately notify your carrier and your dealer 2 Hang the unit in a safe place Please ensure that the unit is properly secured 3 Choose the operation mode Let us look at the function of the DIP switch 1 8 bit Start address from 1 255 1 a Es ss GOB de oe The 9 bit OF FE OFF Sound ac2. ment falls it may cause injuries Do not place heavy object on the equipment Objects may fall and cause injuries When not in use for extended periods unplug the power source for safety When transporting the equipment be extremely careful Dropping it could cause an injury
3. sistors ICs and Diodes or changing other parts are not allowed by unauthorized service centers If there is a problem with the DUO BEAM RG it must be returned to the dealer that you purchased the unit from WARNINGS Visible and invisible laser light direct beam can damage the human eye and the eyes of animals Do not look at any Laser light directly Do not touch the laser aperture with the hand When cleaning the laser aperture please use cotton with rubbing alcohol or camera lens cleaner Do not take apart or modify the equipment Fire or electrical shock may result lf you hear unusual noises see smoke feel excessive heat or smell anything unusual immediately unplug the power source and contact your retailer Continued use may result in fire or electrical shock Do not use flammable sprays near this equipment Also do not spill water liquids or flammable liquids on the equipment If these fluids enter this equipment and contact the electrical parts fire or electrical shock may result If anything enters the equipment immediately unplug the power supply and contact your retailer CAUTION Do not place the equipment in the following areas Fire or electrical shock may result Areas with high humidity Areas subject to direct sunlight Areas with high temperatures Areas near flame sources Do not place the equipment on shaky stands unstable surfaces or surfaces subject to frequent vibrations If the equip
4. tivation mode co ll AR ON DMX512 mode The 10 bit Not Connected e Sound Active Mode When the equipment operates in this mode the patterns will be changed by music Please follow the instructions as below 1 Set the 9 bit of DIP Switch on the back panel to the OFF position Factory default 2 Plug in the power source the equipment will self test for about 10 seconds 3 Turn the Speed knob left max right min to adjust the speed that the patterns will change DMX 512 Mode When the unit is operated in this mode you can use a standard DMX512 controller to change laser colour laser on off patterns soeed and so on Please follow the instructions below 1 Put the 9 bit of DIP Switch on the rear panel up to the ON position 2 Set the start address 1 8 bit of the equipment 3 Connect to the DMX512 controller There are five channels totally Channel Function 0 63 Blackout 64 127 Green On 128 191 Red On 192 255 Both OrXred and Green 2 Patten Selection 3 Speed 4 Scanning Frequency 5 Pattern Reset Rest Vaue 255 4 Plug in the power source the equipment will self test about 10 seconds Then you can change the patterns and speed through the DMX controller 5 DMX Connectors use XLR connectors with three pins Pin 1 Ground Pin 2 Negative Data Pin 3 Positive Data Service and repair The DUO BEAM RG has no major serviceable parts Repair of electronic components tran
Download Pdf Manuals
Related Search