TES9 Hardware Manual
Contents
1. 107220 VAC 50 60 Hz FUSE 1 AMP 250 VOLT ep e o Jo A gt a Je a ep LOAD LTCIN MOEN LIRE PORTC e J iss e Figure 2 2 Rear Panel One channel TES9 110 220 VAC 50 60 Hz FUSE 1 AMP 250 VOLT e MON OUT ou IN ole oQ 9 9 QU e p SP ORTC LAN Figure 2 3 Rear Panel Two channel TES9 The following sections describe the connections and controls on the rear panel Power Connection The power entry module accepts a standard power cord supplied with the unit The power cord type is specified at the time of purchase If your cord has the wrong plug for use with your power outlet please contact your Ross Video sales representative The AC power input must be in the range 90 to 250 VAC and 47 63 Hz The fuse is rated at 1 A and 250 V The fuse drawer in the power entry module contains the active fuse and a spare PROGRAM 1 AND 2 VIDEO The following description applies to both the Program 1 channel and the Program 2 channel if it is installed All BNC video jacks present an impedance of 75 ohms These high quality jacks provide excellent impedance characteristics over the range of frequencies required for 292M and 259M signals IN The IN jack for each channel provides the video input to the encoding and decoding circuits of the TES9 When the channel s2. TES9 Hardware User Manual Iss 02 Introduction 1 3 Documentation Terms and Conventions 1 4 Introduction The following terms and conventions are used throughout this manual All references to the TES9 also includes all versions unless otherwise indicated Operator and User refer to the person who uses TES9 System and Video system refer to the mix of interconnected production and terminal equipment in your environment Video by itself as a synonym for 259M or 292M that is when either video type is appropriate For features that apply to one video format only such as VBI processing in 259M the manual names the format explicitly The Operating Tips and Note boxes are used throughout this manual to provide additional user information TES9 Hardware User Manual Iss 02 Hardware Overview In This Chapter This chapter provides an overview of the TES9 The following topics are discussed Before You Begin Front Panel e Rear Panel TES9 Hardware User Manual Iss 02 Hardware Overview 2 1 Before You Begin Before proceeding with the instructions in this manual review the following notes Static Discharge Throughout this manual please heed the following cautionary note semiconductor devices Avoid handling circuit boards in high static environments such as carpeted areas and when synthetic fiber clothing is worn Always exercise proper grounding precautions when
3. When connecting to another device such as a PC that is wired as Data Terminal Equipment DTE you need to use a null modem cable such as the one supplied with the TES9 Additional cables can be purchased by contacting your Ross Video sales representative Alternatively you can build your own cable or find an equivalent one available from a cable supplier using the wiring table provided in section When connecting to a device that is wired as Data Communications Equipment DCE such as a modem you need to use a straight through 9 pin cable instead of the null modem This cable is not supplied with the TES9 but is readily available from data cable suppliers Although you used PORT A for your initial setup you do not have to dedicate it to this purpose alone If you enable setup to occur through the LAN PORT A is then available for data transmission Also PORT A can be used alternately for setup and data transmission provided your application allows the data transmission to be suspended whenever you need to change the setup LAN The LAN port can be connected to a 10baseT or 100baseT Ethernet LAN using a standard cable with RJ45 jacks The LAN port uses a standard pin out which means that it is intended to be connected to a router or switch using a standard cable If you need to connect directly to the LAN port on terminal equipment such as a PC you will need to use a crossover cable MODEM The modem can be connected via
4. 4 3 Cabling Information This section provides additional cabling information for the TES9 RS 232 Ports The pin connections for PORT A PORT B and PORT C are shown in Table 4 5 These D9 jacks are the same type commonly found on PCs Table 4 5 D9 Pin Connections Direction Status Input to TES9 Not connected Input to TES9 Active Output from TES9 Active Output from TES9 Asserted 12V Ground reference Ground Input to TES9 Not connected Output from TES9 Active Input to TES9 Active OO o ANT DD NM BY WwW N Input to TES9 Not connected The following table shows the wiring of the 91 09497 01 null modem cable supplied with the TESI This table can be used to construct a cable to connect PORT A PORTB or PORTC to a COM port on a PC or other such equipment This shows for example that the DTR signal on pin 4 of the TES9 drives pins DCD and 6 DSR on the PC Table 4 6 Connection from TES9 to a PC TES9 D9 Connector PC D9 Connector Name Pin Name RXD TXD DTR GND DCD DSR RTS CTS CTS RTS No connection No Connection a The connections to pins 1 and 6 of the TES9 ports are optional since the TES9 does not use them However it is advisable to connect them in order to keep the cable symmet rical 4 4 Specifications TES9 Hardware User Manual Iss 02 GPIO Note that the GPIO terminal block is a two pa
5. CEA 608 captions in 259M and CEA 708 captions in 292M e Compact rack unit enclosure e Universal AC power input 90 250 VAC 47 63 Hz e Accepts 259M and 292M signals in all the major formats e High quality 75 ohm BNC connectors and video processing e Video bypass via a high quality 75 ohm RF relay when the unit is powered off or when certain malfunctions are detected Front panel pushbuttons to force relay bypass Monitor outputs for both video paths to allow the output signals to be observed and analyzed even when the unit is in bypass e VANC insertion and extraction per SMPTE 334M Can process multiple different data streams carried in any combination of the scan lines that are available for VANC data e Can add a data service to others that are already present in a line without delaying the existing services This is a major improvement over earlier equipment that would extract TES9 Hardware User Manual Iss 02 existing data services add the locally generated data to them and re insert the combined data one frame later The TES9 eliminates the accumulation of delay in the data resulting from multiple processing passes This is crucial for data services such as closed captioning and metadata which must maintain tight synchronization with the video program Allows user control of the order of data packets in insertion lines Local data can be added before existing services if desired this allows the user to p
6. working on circuit boards and related equipment ESD Susceptibility Static discharge can cause serious damage to sensitive Unpacking Unpack each TES9 you received from the shipping container and ensure that all items are included If any items are missing or damaged contact your sales representative or Ross Video directly 2 2 Hardware Overview TES9 Hardware User Manual Iss 02 Front Panel The front panel ofthe TES9 is shown in Figure 2 1 The indicators and controls on the front panel of the TES9 are described in the following sections TES9 e PROGRAM 1 PROGRAM 2 0000000000000 Pora uw L voro voro c e Gs e Cn Gen Gn n CNXOC OO DOCDODEOED Ponte E suus L encobe Lj cene OOCOCOOOOOOOO00C ODOCCOCODOOODOOO E senre Stans pecore DECODE 0000000000000 MODEM O sramss ByPass m O ByPass _ ACTIVE BYPASS e Port Status Program 1 video Program 2 video LEDs LEDs LEDs amp switch LEDs amp switch Figure 2 1 TES9 Front Panel Controls and Indicators In general the LED indicators have the meanings shown in Table 2 1 Exceptions to these definitions are noted where appropriate Table 2 1 LED Indicators LED Color Description Off Not used or not selected Green Normal operation Red Disabled due to an error Yellow In use but an error is detected Warning to user On STATUS 1 this means do not turn pow
7. 91 09497 01 supplied with the TES9 to a 9 pin COM port on your PC 2 Connect the other end of the null modem cable to PORT A of the TES9 If the cable is not long enough you can add a 9 pin extension cable up to 25 feet 8 metres long Turn the TES9 and PC power on Once the PC has booted place the CD ROM supplied with the TES9 into its CD drive and follow the instructions to install the software If you want more details about this software please consult your TES9 software manual 5 The TESO should have started operation while you were installing the software Press the LOAD button on the TES9 s rear panel using a narrow object such as a pencil if necessary and hold it in for at least two seconds The TES9 will enter setup mode and the STATUS1 LED should be alternating between green and yellow 6 Start the setup software using the instructions in the TES9 software manual Data Connections 3 6 Installation As discussed at the beginning of section your data connections depend on the use you are making of the TES9 and the software installed in it The following sections describe each of these connections but are not meant to imply that you should necessarily connect them all RS 232 Ports The RS 232 ports PORT A PORT B and PORT C can all be connected as described in section Connecting a PC for Setup on page 3 5 for use in data transmission This is the connection discussed in the first of the following points
8. E 2 7 PROGRAM 1 AND2 VIDEO rinena nonin NR 2 7 Data Polis nenien eae E E E E E geet EE 2 8 Control Connections icd ae eR E A ERAR ESS 2 8 Installation 3 Unpacking the TESS daniela 3 2 Mounting the TES9 1n a Rack iaia tene tentent tente Pertanto entrent 3 3 Ire follis un TH G da 3 3 Installing the TESO in the Rack esee enne 3 3 Basic Connections one T PR D eb n ERR betae 3 5 Video Connections ritiene cte better gre i Dele ae Perge tet ue ED ES 3 5 Connecting a PC for Setup 55 gingen nnn i OE ERE EUR EE HERE 3 5 Data Connections aria e ba ed de e ORG HE cei ee e HO RUE RUE CY 3 6 Specifications 4 Technical Specifications roter Rer REED EIER a 4 2 Electrical Specifications comes te TG tertie ia 4 2 Mechanical Specifications i 4 2 Environmental Specifications ari 4 2 Cabling Information ilaele 4 4 RS 232 Pois eee aan 4 4 GPIO ara E E E A 4 5 Troubleshooting 5 Troubleshooting tit ter RR eee seo Ee ERAR aia 5 2 Replacing a Filse inane aaa er criss costs TE recede Yo Pe vete oes 5 2 Falls to Start ip REPREHENE URP lene 5 2 Stays m Bypass 3 55 bilia Pee eec ee ee ege o eere 5 2 Cannot Decode TES9 Encoded Data i 5 3 TES9 Hardware User Manual Iss 02 Contents i ii e Contents TES9 Hardware User Manual Iss 02 Introduction In This Chapter This ch
9. ES9 and are ready to insert it into your program path use the following procedure 1 Assuming that you want to insert the TES9 into the video path between two pieces of equipment we ll call A and B select a time when a loss of video on this path will not cause an outage 2 Disconnect the video cable from the input to B and connect it to IN of the TESO 3 Connect another HD grade coax from the TES9 OUT to the input of B 75 ohm termination to OUT Termination of the output in 75 ohms is essential for proper operation Note f the TES9 is used as a decoder and its output is not used connect a 4 Place the TES9 s BYPASS switch in the bypass out position 5 Turn on the TES9 s power by moving the rear panel power switch to the 1 up position 6 After the TES9 has powered up its STATUS 1 3 LEDs should all be green as well as the VIDEO LED for the channel you ve just connected The BYPASS LED will be red Once this is the case press the switch in The BYPASS LED should go off and the TESS should now be fully active in your program path Connecting a PC for Setup When you first use your TES9 you will need to connect it to a Windows PC in order to set up its operating parameters It is recommended that the PC and TES9 be powered off while you make these connections Use the following procedure TES9 Hardware User Manual Iss 02 Installation 3 5 1 Connect one end of the null modem cable
10. O connector Acommand from a remote computer For example while starting up new software that has been loaded into the TES9 the software may bypass the video to avoid glitching it e An internal fault condition such as a power supply failure When any of these conditions occurs or the front panel switch is in the BYPASS position the video path is bypassed and the BYPASS LED is illuminated red Otherwise the BYPASS LED is off and the video LED should be green VIDEO LED The VIDEO LED is illuminated green when there is a usable 292M or 259M video signal connected to the input jack for the corresponding channel The following table describes the operation of the VIDEO LED in detail Table 2 3 VIDEO LED Color Description Normal video is connected and used Video is connected but the channel is not enabled that is no suitable data streams are defined for the video type For example VBI encoding is enabled but the input is 292M or no data Yellow streams at all have been defined Red No video input on a channel that is enabled Off No video input on a channel that is not enabled Green with one yellow EDH or CRC error in input Continues for 5 seconds after the last flash per second error is detected ENCODE LED The ENCODE LED is illuminated green when the TES9 is inserting data into the corresponding video signal If the video is 292M the inserted data is VANG if it is 259M it can be e
11. SSS oo Ross Video Limited TES9 Multi Function HD SD SDI VANC Processor Hardware User Manual ROSS Live Production Technology TES9 e Multi Function HD SD SDI VANC Processor Hardware User Manual Ross Part Number TES9DR 004A 02 Release Date September 29 2010 Printed in Canada The information contained in this manual is subject to change without notice or obligation Copyright 2010 Ross Video Limited All rights reserved Contents of this publication may not be reproduced in any form without the written permission of Ross Video Limited Reproduction or reverse engineering of copyrighted software is prohibited Patents This product is protected by the following US Patents 4 205 346 5 115 314 5 280 346 5 561 404 7 034 886 7 508 455 This product is protected by the following Canadian Patents 2039277 1237518 1127289 Other patents pending Notice The material in this manual is furnished for informational use only It is subject to change without notice and should not be construed as commitment by Ross Video Limited Ross Video Limited assumes no responsibility or liability for errors or inaccuracies that may appear in this manual Trademarks ROSS is a registered trademark of Ross Video Limited Ross ROSS ROSS are registered trademarks of Ross Video Limited All other product names and any registered and unregistered trademarks mentioned in this guide are used for identification purposes o
12. These instructions can be used for racks having a total depth from the front to the rear rails in the range 24 30 25 61 77 cm For racks that are shallower than 24 a modified procedure is described in step 3 below For racks deeper than 30 25 use a mounting shelf Installing the TES9 in the Rack Use the following procedure to install the TES9 in the rack 1 Attach the rear TES9 brackets 41 10437 01 to both sides of the chassis using the mounting holes near the rear of the TES9 Use the 28 32 flat head screws and insert them through the countersunk holes in the bracket into the mounting holes on the TES9 See item 3 in Figure 3 1 Install four nut clips to the front of the rack and attach the TES9 front panel to these clips using four 3 4 410 32 screws TES9 Hardware User Manual Iss 02 Installation 3 3 3 4 Installation If your rack is shallower than 24 61 cm and it has side mounting rails use the following procedure Otherwise proceed to step Install four nut clips to the rear of the rack at the same height as those used to mount the front of the TES9 Skip Steps Install four nut clips to the rear of the rack at the same height as those used to mount the front of the TES9 through Install two 3 8 10 screws through the slots in each rear bracket into the captive nuts near the rear end of the TES9 brackets See item 5 in Figure 3 1 Instead mount the rear nut clips to the rear side rails and attach t
13. a standard telephone cord to an outlet of any analog telephone system Avoid using a digital telephone line since these tend to reduce the quality and therefore the speed of the modem connection If the telephone line goes outside your building you should TES9 Hardware User Manual Iss 02 ensure that it is equipped with a surge suppressor to protect the TES9 s modem from external high energy discharges TES9 Hardware User Manual Iss 02 Installation 3 7 3 8 Installation TES9 Hardware User Manual Iss 02 Specifications In This Chapter This chapter provides the technical specification information for the TES9 Note that specifications are subject to change without notice The following topics are discussed Technical Specifications e Cabling Information TES9 Hardware User Manual Iss 02 Specifications e 4 1 Technical Specifications This section provides technical information on the TES9 Electrical Specifications Table 4 1 TES9 Electrical Specifications Specification 90 250V 47 63 Hz 0 25A typical fuse 1A Power Replacement fuse Littelfuse 218001 Port A Port B Port C RS 232 up to 115 2K bps PROGRAM 1 and 2 VIDEO IN OUT and MON SMPTE 259M or 292M 800 mV p p 75 ohms OUT GPIO Contact closures and 5V logic levels Ethernet 10baseT or 100baseT MODEM V 34 analog telephone connection Linear time code SMPTE 12M unbalanced 0 5 3 V peak to peak 5K ohms Me
14. apter contains the following sections Overview Documentation Terms and Conventions A Word of Thanks Congratulations on choosing an TES9 Multi function HD SD SDI VANC Processor Your TES9 is part the Ross Terminal Equipment family of products backed by Ross Video s experience in engineering and design expertise since 1974 You will be pleased at how easily your new TESO fits into your overall working environment Equally pleasing is the product quality reliability and functionality Thank you for joining the group of worldwide satisfied Ross Video customers Should you have a question pertaining to the installation or operation of your TES9 please contact us at the numbers listed on the back cover of this manual Our technical support staff is always available for consultation training or service TES9 Hardware User Manual Iss 02 Introduction 1 1 Overview The TESO is a broadcast quality ancillary data encoder for uncompressed digital video signals It operates with high definition signals that comply with SMPTE standard 292M and standard definition signals that comply with SMPTE 259M Depending on the model it can process either one or two video signals The TESO inserts data having various formats and purposes into the vertical blanking portion of its video input signal s These vertical ancillary VANC data streams comply with SMPTE standards 291M and 334M The TES is also capable of extracting VANC data from it
15. bypass relay is in the Active position the TES9 provides a 75 ohm termination for the input signal When the bypass relay is in the Bypass position the IN jack is connected directly to the OUT jack the signal connected to IN sees its 75 ohm termination in the equipment connected to the OUT jack The video signal connected to the IN jack is expected to comply with one of following SMPTE standards 259M or 292M A list of video formats is provided in later When the channel s bypass relay is in the Active position the OUT jack carries the video signal applied to the IN jack with VANC and or VBI data added as specified by the user The output impedance is 75 ohms When the bypass relay is in the Bypass position the OUT jack is connected directly to IN via the relay contacts MON OUT The MON OUT jack carries the video signal applied to the IN jack with VANC and or VBI data added as specified by the user It is the same as OUT except that it is not affected by the state of TES9 Hardware User Manual Iss 02 Hardware Overview 2 7 the bypass relay This allows the video output of the TES9 to be observed with test or monitoring equipment even when the TES9 is in bypass The output impedance is 75 ohms Data Ports The following standard data ports are available on the rear panel PORTSA B C These are RS232 9 pin up to 115 2Kbps wired as DTE Port A can be used for setup and all three ports can be used for data transfer between
16. chanical Specifications Table 4 2 TES9 Mechanical Specifications GERA Dimension UUU O Width 19 48 3 cm Height 1 72 4 4 cm Depth 12 2 31cm Weight 6 6 Ibs 3 0 kg Mounting Front and rear mount in standard 19 rack Environmental Specifications The TES9 operating temperature range is 0 to 40 C or 32 to 104 F 4 2 Specifications TES9 Hardware User Manual Iss 02 Video Specifications The TES9 inputs and outputs comply with SMPTE 259M and 292M The following table lists the video formats that are supported Table 4 3 TES9 Video Specifications 525 lines 59 94 Hz ITU R BT 601 SMPTE 125M omo 625 lines 50 Hz ITU R BT 601 1080i 50 Hz SMPTE 274M 10801 59 94 Hz SMPTE 274M MPTE 274M S 1080p 23 98 Hz SMPTE 274M 1080p 24 Hz SMPTE 274M S S 10801 60 Hz 1080sf 23 98 Hz MPTE 274M RP211 1080sf 24 Hz MPTE 274M RP211 720p 59 94 Hz SMPTE 296M 720p 60 Hz SMPTE 296M The following table lists some additional video signal specifications Table 4 4 TES9 Additional Video Specifications THD Dimension Outer Jitter 0 1 UI typical 0 2 UI maximum Output Return Loss active 15 dB minimum to 1 485 GHz Input Return Loss active 10 dB minimum to 1 485 GHz Automatic Input Cable 292M at least 75 m of 8281 cable Equalization Pathological 259M at least 200 m of 8281 cable TES9 Hardware User Manual Iss 02 Specifications
17. d out wheeled bin symbol invites you to use these systems If you need more information on the collection reuse and recycling systems please contact your local or regional waste administration You can also contact Ross Video for more information on the environmental performances of our products Company Address Ross Video Limited ROSS 8 John Street Iroquois Ontario Canada KOE 1K0 General Business Office Fax Technical Support After Hours Emergency E mail Technical Support E mail General Information Website Ross Video Incorporated P O Box 880 Ogdensburg New York USA 13669 0880 1 613 o 652 e 4886 1 613 e 652 e 4425 1 613 e 652 4886 1 613 e 349 e 0006 techsupport rossvideo com solutions rossvideo com http www rossvideo com Contents Introduction 1 Ja 1 2 huuc t M 1 2 Documentation Terms and ConventionS nennen 1 4 Hardware Overview 2 Before You Begl eeicoscec aeterne eae dete RE i 2 2 Static Discharge oun o UBER DRE oi 2 2 Unpacking icc acest ated e d e sala biet a 2 2 Front Panel tecti ione no d E ERR ERE ERR REUTERS 2 3 Port LEDS M Hr 2 3 STATUS LEDS pies r enit tede m eit Eee edt 2 3 Program 1 and 2 LEDs and Switches essen 2 4 Rear Panel uiid EROR RUE RR EE ERE E A OR ERE E 2 7 Power COMMCCH OM ipa TA eee
18. eo 259M to 292M or vice versa This state should last a few seconds The TESO is in Setup mode reached by pressing the LOAD Flashing Yellow and Green switch for 2 seconds ready to communicate with a Windows PC to allow you to adjust its setup The TES9 is in Load mode reached by powering on with the Flashing Yellow LOAD switch pressed ready to communicate with a Windows PC to allow you to update its software Configuration changes or software updates are being saved in the TES9 Never turn off power to the TES9 in this situation as this could result in a loss of software that will require the unit to be returned to the factory for repairs Flashing Yellow and Red STATUS 2 LED The STATUS 2 LED is off when the TES9 is operating normally Once the TES9 has started up the presence of any red on this LED indicates an application error that can probably be corrected by changing settings or inputs Refer to the software manual for details on this LED STATUS 3 LED The STATUS 3 LED is off when the TESO is operating normally Once the TES9 has started up the presence of any red on this LED indicates a major error If this occurs please note the flashing pattern if any before calling Ross Technical Support Program 1 and 2 LEDs and Switches The front panel provides a bypass push button switch and 4 LEDs for each of the video paths PROGRAM 1 and 2 through the TES9 These are installed for all models of TES9 This
19. er off while data is being saved to flash memory Flashing Yellow and Red Port LEDs There is one LED for each of the data ports on the rear panel The green PORT A PORT B and PORT C LEDs follow the data on the RS232 ports If the transmitted and or received data is constant the green LED will be on continuously if the data 1s intermittent it will blink accordingly The MODEM and LAN LEDs are green when data is being transmitted or received through the corresponding port and off otherwise If the software detects a problem with one of these ports it illuminates the corresponding red LED STATUS LEDs The STATUS1 STATUS2 and STATUS3 LEDs are used to indicate the status of TES9 functions that do not have their own dedicated front panel LEDs When the TES9 s power is first turned on the three STATUS LEDs will all be illuminated red Once the TESO is operating normally STATUS 1 should be green and STATUS 2 and STATUS 3 should be off STATUS 1 LED The STATUS 1 LED indicates conditions that are common to all TES9s as shown in the following table There may be additional combinations that depend on the operating software TES9 Hardware User Manual Iss 02 Hardware Overview 2 3 Table 2 2 STATUS 1 LED Color Description Red Powering up If the LED stays red for more than 45 seconds this j indicates a system failure Green Normal operation The TES9 is reconfiguring due to a change in video type from S
20. he TES9 brackets directly to these side rails using 3 4 2210 32 screws through the slots in the brackets e Proceed to step 7 Install four nut clips to the rear of the rack at the same height as those used to mount the front of the TES9 Attach the two rear rack brackets to the nut clips installed in the preceding step using two 3 4 4410 32 screws for each bracket See item 4 in Figure 3 1 Before tightening the screws ensure that these brackets contact the inner side of the brackets mounted to the TES9 that is they should be closer to the center of the rack than the ones on the TES9 The slots in these brackets should also be approximately aligned with the screw holes in the TES9 brackets Install two 3 8 10 screws through the slots in each rear bracket into the captive nuts near the rear end of the TES9 brackets See item 5 in Figure 3 1 Plug the power cord into the receptacle on the rear of the TES9 Insert a tie wrap through the strain relief bridge on the rack bracket near the TES9 power entry module see item 6 in Figure 3 1 Pass the tie wrap around the power cord and tighten it to prevent the power cord from being inadvertently pulled out of the TES9 Insert the TES9 s power plug into a 110 or 220 VAC outlet The use of conditioned power from an uninterruptible power source UPS is strongly recommended in order to ensure that the processing of the video and ancillary data is not disturbed by power outages TES9 Hard
21. includes models that do not have a PROGRAM 2 video section in this case the PROGRAM 2 LEDs are always off and the PROGRAM 2 bypass switch has no effect The following discussion applies to either channel Q Note On some models of TES9 the two video channels may be labeled amp PROGRAM and AUXILIARY instead of PROGRAM 1 and PROGRAM 2 Their functions are nevertheless identical BYPASS LED The BYPASS LED and switch operate together as follows The BYPASS LED is illuminated red whenever the video is bypassed by the internal relay the LED is on in all bypass situations except when the power is off The BYPASS switch is one of several devices that can force the corresponding video path into bypass 2 4 Hardware Overview TES9 Hardware User Manual Iss 02 If the switch is in the BYPASS position out the internal relay connects the video input directly to the output regardless of any other operational conditions As discussed the LED is illuminated red in this case When the switch is pushed in ACTIVE position the bypass relay for the corresponding video channel should normally be switched to the active position and the LED should go off However there are other conditions that can hold the video in bypass even though the switch is in the ACTIVE position These include the following No video input or unrecognized video format Acontact closure on the bypass pins of the rear panel GPI
22. is damaging the inserted data try connecting the decoding device directly to the video output of the TES9 to check this If you have access to a video analyzer connect the TES9 Video Out to it to check the presence and coding of the encoded data TES9 Hardware User Manual Iss 02 Troubleshooting 5 3 Notes 5 4 Troubleshooting TES9 Hardware User Manual Iss 02 Notes Contact Us Contact our friendly and professional support representatives for the following e Name and address of your local dealer e Product information and pricing Technical support e Upcoming trade show information General Business Office and Technical Support eG ne mene PHONE After Hours Emergency 613 349 0006 Fax 613 652 4425 General Information solutions rossvideo com E MAIL Technical Support techsupport rossvideo com 8 John Street Ross Video Limited Iroquois Ontario Canada KOE IK POSTAL i SERVICE P O Box 880 Ross Video Incorporated Ogdensburg New York USA 13669 0880 Visit Us Please visit us at our website for Company information Related products and full product lines On line catalog News Testimonials WA COIi3video com Ross Part Number TES9DR 004A 02
23. is yellow there are no appropriate data services defined for the current video type Use the setup software to check the settings If VIDEO LED is green and ENCODE LED is off there are data services defined but no data is being provided Use the setup software to check the settings Check that the data port that should be providing the data e g Port A C or LAN is connected and that the data source is operating If using one of the RS 232 connections PORT A C check that the baud rate is set properly and that the cable is the proper null modem type as defined in section If the LED for the specified port is on or flashing green data is being received and there is probably an incorrect setting in the TES9 If the LED for the specified port is solidly off the problem is with the data source or the cable If using the LAN connection check that the LAN LED is on Check that the LAN settings of the TES9 IP address etc match those used by the application that is sending the data Make sure that the sending application 1s running If both VIDEO and ENCODE LEDs are green encoding is taking place If you are unable to decode the data from the expected line downstream check the following possibilities The TES9 may be setup to encode with a different VANC address DID SDID or in a different line or component chroma or luma than those expected by the decoding equipment check the settings There may be equipment downstream from the TES9 that
24. ither VANC or VBI The TES9 can be configured to append VANC data to a line that already contains VANC packets In this case there is a possibility that some of the data will not fit in the available space in the line When this occurs the ENCODE LED will flash yellow to indicate that the user needs to adjust some settings This is described in the following table TES9 Hardware User Manual Iss 02 Hardware Overview 2 5 Table 2 4 VIDEO LED Color Description Green Normal data is inserted into the video Off No encoding Green with one Yellow Too much data for an insertion line The user has given priority to flash per second incoming data so local data is lost Green with five Yellow Too much data for an insertion line The user has given priority to flashes per second local data so incoming data is lost DECODE LED The DECODE LED is illuminated green when the TES9 is extracting data from its video input If the video is 292M the extracted data is VANC if it is 259M it can be either VANC or VBI The LED will be green when the software has set up the hardware to extract incoming data and the data is present If the software does not need to extract incoming data for its current operating mode or if the data is absent from the video input the LED is off 2 6 Hardware Overview TES9 Hardware User Manual Iss 02 Rear Panel The rear panel of the TES9 is shown in Figure 2 2 and Figure 2 3
25. lace the most important services at the beginning of a line where they may be most likely to be handled properly by downstream equipment The user can direct the TES9 to insert local data both before and after existing services or to overwrite them Incoming VANC services can either be decoded regardless of the lines where they are carried or the search can be restricted to specific lines The user can select incoming VANC services or complete lines to be selectively deleted by the TES9 when adding its own data to the signal LAN 100baseT V 34 modem and three RS232 ports are standard on all TES9 s A 15 pin terminal block on the rear panel provides remote bypass control and indication for both video paths as well as 7 general purpose input output GPIO signals An unbalanced LTC input is provided for applications that require time code input The TESO software is stored in internal flash memory which allows the software to be updated through a data port such as the LAN Scope of this Manual This manual covers the following topics TES9 connections controls and indicators Installing the TES9 in a rack Connecting to other equipment TES specifications Basic troubleshooting The TESI accepts various software modules that can be installed at the factory or downloaded subsequently Its versatility is such that the detailed operation of the unit needs to be described in documentation supplied with the software
26. ncorrectly Plug the power cord back into the TES9 s receptacle and turn the power switch to the on up position The two fuses supplied with the TES9 are Littelfuse part number 218001 Fails to Start When power is first applied to the TES9 the three STATUS LEDs should illuminate red After approximately 35 seconds STATUS 1 LED should turn green and the other two should turn off If they do not please note the pattern of these three LEDs and contact Ross Technical Support Stays in Bypass The TES9 requires the following conditions to switch from bypass to active power on front panel bypass switch pressed in bypass switch contacts on GPIO connector open VIDEO IN present TES9 Hardware User Manual Iss 02 5 2 Troubleshooting If the bypass LED stays on after the TES9 has fully powered up even though all the above conditions are met please check that the video input uses one of the formats defined in section If so there may be an internal fault in the TES9 Contact Ross Technical Support Cannot Decode TES9 Encoded Data If the TES9 is out of bypass and it has been set up to encode VANC or VBI services these services should be injected into the designated lines of the Video Out signal If you believe that they are not please check the following The VIDEO and ENCODE LEDs for the desired channel should both be illuminated green The ENCODE LED may be blinking if the data is not continuous If the VIDEO LED
27. nly and remain the exclusive property of their respective owners Information to User The following warning is provided in compliance with the regulations of the United States Federal Communication Commission FCC This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment operates in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference in which case the user will be required to correct the interference at his own expense Any changes or modifications not expressly approved by Ross Video could void the user s authority to operate the equipment Environmental Information The equipment that you purchased required the extraction and use of natural resources for its production It may contain hazardous substances that could impact health and the environment To avoid the potential release of those substances into the environment and to diminish the need for the extraction of natural resources Ross Video encourages you to use the appropriate take back systems These systems will reuse or recycle most of the materials from your end of life equipment in an environmentally friendly and health conscious manner The crosse
28. odules loaded into the TES9 and on the application software that provides the data for encoding Please refer to the manuals for these software packages for additional troubleshooting assistance Replacing a Fuse The AC power to the TES9 is protected by a 1 ampere fuse this is located behind a small cover on the rear panel power entry module If the power cord is attached to the TES9 and plugged into a live AC outlet and the power switch is in the ON position yet none of the LEDs on the TES9 s front panel come on the fuse has probably blown In order to change it use the following procedure T 2 Remove the power cord from the receptacle on the rear of the TES9 Insert a small screwdriver or equivalent tool into the small slot at the upper edge of the fuse holder in the centre of the power entry module Press downwards and pull slightly outwards to disengage the upper clip Repeat the preceding step on the lower clip of the fuse holder If necessary repeat steps 2 and 3 to fully release the fuse holder Carefully pull the fuse holder out of its housing and be prepared to catch the fuse if it falls out Replace the live upper fuse by the spare one in the lower container marked spare fuse If you have a supply of fuses available place a new one in the spare location Carefully return the fuse holder to its housing and press lightly until it clicks into place Note that it is keyed so that you cannot insert it i
29. p it pressed until two seconds after turning the power on the TES9 will be ready to accept a software update through a port from a computer If you press and hold the button for two seconds while the TES9 is operating normally it will suspend normal operation and prepare to accept a connection from a computer running the TES9 setup software 2 8 Hardware Overview TES9 Hardware User Manual Iss 02 Installation In This Chapter This chapter provides a general overview of how to install the TES9 The following topics are discussed Unpacking the TES9 Mounting the TES9 in a Rack Basic Connections TES9 Hardware User Manual Iss 02 Installation 3 1 Unpacking the TES9 In the shipping box for your TES9 you should find the following items The TES9 unit An RS232 null modem cable A Hardware manual e A Software User s manual ACD ROM containing setup software A mounting kit containing hardware needed for rack mounting the TES9 The rack mounting kit for the TES9 contains the following items Table 3 1 Rack Mounting Kit Description Quantity Rear TES9 brackets part 41 10437 01 Rear rack bracket part 41 10438 01 Screw 8 32 flat head 5 16 Nut clip 10 32 Screw 10 32 pan head 3 4 Screw 10 32 pan head 3 8 Tie wrap N If any of these items listed in this section are missing or have been damaged in shipment please contact Ross Technical Support 3 2 Installa
30. re is no connection between these pins These pins are rated at 25V DC and 200 ma maximum TES9 Hardware User Manual Iss 02 Specifications 4 5 Program 2 Bypass Indicator A and B When the TES9 s Program 2 video channel is active these pins are connected together by internal relay contacts When it is in bypass there is no connection between these pins These pins are rated at 25V DC and 200 ma maximum Program 1 Bypass Switch When this pin is connected to ground pin 8 or 12 the Program 1 video channel is placed into bypass When this pin is left unconnected the bypass state is controlled by the front panel bypass switch and other internal controls This pin should not be connected to any other signals it should either be open or connected to ground Program 2 Bypass Switch When this pin is connected to ground pin 8 or 12 the Program 2 video channel is placed into bypass When this pin is left unconnected the bypass state is controlled by the front panel bypass switch and other internal controls This pin should not be connected to any other signals it should either be open or connected to ground TES9 Hardware User Manual Iss 02 4 6 Specifications Troubleshooting In This Chapter This chapter contains the following sections Troubleshooting TES9 Hardware User Manual Iss 02 Troubleshooting 5 1 Troubleshooting Other error conditions not outlined in this section may depend on the software m
31. rt connector For convenience of cable construction the plug can be removed from the socket by loosening the small screws at the two ends of the plug Note 7o avoid interference or damage caused by external electrical transients it is advisable to use a shielded multi conductor cable for the GPIO connections Connect the shield drain wire to pin 8 or 12 of the terminal block in addition to the ground signal wire The following table shows the pin out of the GPIO connector The pins are numbered from left to right as seen from the rear Pins 1 5 10 and 15 are identified on the panel as shown in Figure 2 3 Table 4 7 GPIO Connections Description GPI 0 GPI 1 GPI 2 GPI 3 GPI 4 GPI 5 GPI 6 Ground Pgm 1 Bypass Indicator A Pgm 1 Bypass Indicator B Pgm 1 Bypass Switch Ground Pgm 2 Bypass Indicator A Pgm 2 Bypass Indicator B Pgm 2 Bypass Switch GPI 0 6 These are general purpose 5V logic signal inputs or outputs Each signal is pulled up to 5V by 10K ohms Depending on the application these can be used to provide control or status to an external device or accept control inputs For safe operation these signals must remain within the range 0 5V DC If unused leave them unconnected Program 1 Bypass Indicator A and B When the TES9 s Program 1 video channel is active these pins are connected together by internal relay contacts When it is in bypass the
32. s video input signal s This allows it to forward the data to other systems combine locally generated data with that already carried in the input and bridge data from one video signal to the other In addition to processing VANC data in 292M and 259M signals the TES9 can insert and extract VBI data signals in 259M signals These data lines contain a digital representation of the analog waveforms used for VBI data transmission in standard definition analog broadcasting One very commonly used VBI data type 1s closed captioning which complies with the CEA 608 standard the TES9 can both insert and extract CEA 608 VBI data Features 1 2 Introduction This section describes capabilities that are available in the TES9 hardware platform It is important to note that the various software products that can operate in the TES9 may make use of different subsets of these features The following are the principal features of the TES9 e One or two complete video paths depending on the model e The two video paths allow the TESI to support several interesting applications which include the following Bridging data from one video signal to another for example CEA 608 captions can be extracted from a 259M signal on one input converted to CEA 708 DTV captions and inserted into a 292M signal on the other input Processing VANC data in two independent 292M video channels Inserting data into one 259M and one 292M signal for example
33. the TES9 and other equipment A null modem cable is normally required to connect to other equipment such as computers One null modem cable is supplied with the TES9 The pin list for these ports and the wiring for the null modem cable are in section MODEM This is a RJ11 jack for 33 6 Kbps connection through a standard analog telephone line This is typically used for captioning data input or remote maintenance LAN This is a RJ45 jack for 10baseT or 100baseT Ethernet connection to a local area network This port is typically used for high speed data transfer between the TES9 and other equipment It can also be used for setup and for loading new software into the TES9 LTC This BNC connector accepts an unbalanced linear time code LTC input that conforms to SMPTE 12M This could for example allow certain TES9 operations to be triggered at specific instants in time This should normally be left unconnected Control Connections GPIO This 15 pin terminal block provides remote bypass control and bypass indication contact closures for both TES9 video channels as well as seven general purpose input output GPIO signals The connector pin out and description are in section LOAD This miniature push button switch can be used to control the operating mode of the TES9 You may be able to press it with one of your fingers 1f not use a narrow object such as a pencil If you press and hold the button with the TES9 power off and kee
34. tion TES9 Hardware User Manual Iss 02 Mounting the TES9 in a Rack This section describes how to mount the TESO in the rack In using these instructions consult Figure 3 1 Note that the TES9 should be attached to both the front and rear of the rack because of the weight of the potentially large number of cables connected to the rear of the TES9 rear rack mounting is strongly advised Before You Begin The first step in installing the TES9 is to select a suitable location The TES9 requires a 1 rack unit 1 75 space in a standard 19 rack Its two cooling fans draw cool air in through the intake vents at the front and exhaust warmer air out the right side as seen from the front The TES9 s power dissipation is quite modest approximately 25 watts nevertheless it is important to select a location that allows this airflow in order to ensure a long operating life 9 bracket gt E 1 i O E 1 p 0 ol P 0 1 TES9 Py ol 12 Rack bracket O o Ob 0080 00 d 0 0 0 b 0 0 i 0 p 0 0 0 0 D o ono 0 lt J es e e Bus n E ME ooo ou m m jon e A 6 Cord attach 4 10 32 3 8 32 5 10 32 3 4 screws 5 16 screws 3 8 screws ss 5S oGccc gt 000000000900 ss Gu e 09000006000 0 dle eccesso A O 900000000 Figure 3 1 TES9 Rear View Rack mounting Detail
35. ware User Manual Iss 02 Basic Connections The required connections to the TES9 depend on the application You may wish to familiarize yourself with the video and data connections supported by your software before proceeding with this section This information can be found in the software manual supplied with your TES9 In general you will need to connect video to the IN and OUT jacks for the Program 1 channel and also for the Program 2 channel if applicable You will also need to connect one or more data cables RS232 LAN modem for transferring data to and from the TES9 During this installation phase you will also need to connect a Windows PC to PORT A using the supplied null modem cable for use in setting your TES9 operating parameters Afterwards you can decide whether to disconnect the PC from PORT A or leave it permanently connected Video Connections Itis strongly recommended that you first connect a video test signal or a DA feed of your program to the PROGRAM IN jack of the TES9 and connect the TES9 OUT jack to monitoring or test equipment This will allow you to become familiar with the operation of the TES9 discover its features and try out its setup software with no effect on your program path circuit you must use HD grade 75 ohm cable such as 8281 or 1694 types for all video connections Important n all cases whether the TES9 is in your program path or in a test Once you have gotten to know the T
Download Pdf Manuals
Related Search