Audio Transceiver Manual
Contents
1. On Note Different phones and tablets have different procedures to activate the Bluetooth function pair connect with other Bluetooth devices For example 6 11 Declaration of conformity 11 1 EU This product is CE certified according to the provision of the R amp TTE Directive 99 5 EC Declare that this product is in compliance with the essential requirements and other relevant provisions of Directive 1999 5 EC 11 2 Trademark Statement The Bluetooth word mark and logos are owned by the Bluetooth SIG Inc apt X words and logos marked with a or are trademarks registered or owned by CSR plc or one of its group companies and may be registered in one or more jurisdictions except that not all such marks are registered in all countries where products are available 11 3 FCC RF exposure This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment This equipment should be installed and operated with minimum distance 1 5cm between the radiator amp your body This transmitter must not be co located or operating in conjunction with any other antenna or transmitter 12 Warranty To avoid any damage or device malfunction do not drop the device from high places Keep the device away from humidity water and or other liquid If the device is exposed to water moisture or other liquid do not operate it to avoid any electrical shock explosion and damage to the device or yourself2. eB eB eB eB eB eB a a BB a BB eB eB eB eB eB eB BP eB eB eB eB a eB eB eB eB ee Ee Ee SK SK 4 Transmitter turn On Off Push the click button to TX mode from TX RX positon before power on TX or RX mode cannot be changed after powering on Ranger AT0200 Turn On press and hold the MFB button for about 5 seconds until the blue LED is on for 1 second Note For first time use or first time turn on after clear connection list Ranger ATO200 transmitter will automatically enter into pairing mode LED flashes blue quickly Turn Off press and hold the MFB button for about 3 seconds until the red LED is on for 1 second and then goes off 5 Transmitter pairing with a Bluetooth device After Ranger AT0200 under TX mode has connected to a Bluetooth stereo device you can stream music wirelessly Before pairing please make sure your Bluetooth stereo receiver supports Bluetooth A2DP profile Pairing procedure A Plug the 3 5 mm audio cable into Ranger AT0200 3 5 mm audio socket Plug the other end or 2 x RCA into the audio output of an audio source system e g iPod TV Treadmill etc B Ensure Ranger AT0200 has pushed into TX mode and the device is off C Put Ranger AT0200 and your Bluetooth stereo receiver device within 1 meter D Power on your Bluetooth stereo receiver device and put it into pairing mode E Press and hold Ranger AT0200 MFB button for around 5 7 seconds until the blue LED blinks quickly indicating it is in
3. pairing mode Note For first time use or first time power on after clearing the connection list Ranger ATO200 will automatically enter into pairing mode the Blue LED blinks quickly F Ranger AT0200 will then automatically search pair and connect with your Bluetooth stereo receiver device G After successful connection the Blue LED will flash twice every 4 seconds H Pairing is complete now you can enjoy the wireless audio button around 7 seconds blue led blinks quickly Push button to TX mode A Za pi _ Press multifunction me button around 3 5MM Jack S 7 seconds blue and red blinks C Auto off Ranger AT0200 will automatically power off if no devices can be connected within 5 minutes D Clearing pairing list Ensure Ranger AT0200 is off press and hold MFB button for around 10 12 seconds till red LED is on for 1 second and then Blue LED is on for 1 second 9 Product Specification Bluetooth V2 1 EDR Bluetooth profile supported A2DP and AVRCP Supported codec aptX SBC e Operation range Class 2 10 meters e TX mode working time up to 10 hours e RX mode working time up to 9 hours e Standby time up to 400 hours Charging time about 2 3 hours e Charging input voltage DC 5V e Battery 270mAH rechargeable Ll polymer battery e Weight 48 5g e Size 50mm L x37mm W X13mm H The working and standby times may vary when used wit
4. 1 Product description The Ranger AT0200 is a 2 in 1 Bluetooth receiver and transmitter which incorporates the latest aptX codec for less latency high audio quality The Ranger AT0200 is very simple to use and enables any Bluetooth enabled music device to connect to both Bluetooth and non Bluetooth devices It can be used to enable a phone to transmit music to a home stereo system or just as easily to allow a CD player or other device to transmit music to a Bluetooth enabled speaker system or headphones With a compact design and internal rechargeable battery with long playing time the Ranger AT0200 is the ideal solution to link your music devices any time and any place you need it 2 Product overview 1 LED Indicator 2 Multi Function Button MFB Power On Off Pairing 3 Micro USB charging socket 4 3 5 mm audio jack 5 TX RX switch button What s in the box A Ranger AT0200 B 3 5mm to 3 5mm audio cable C USB charging cable D 3 5mm to RCA audio cable E User manual F 3 5 audio connector 3 Charging LED Indicator Multi function Button MFB Ranger AT0200 comes with a built in rechargeable battery that provides a very long standby and working time We recommend charging the battery fully before using it for the first time 1 Insert one Micro USB charging cable end into Ranger AT0200 Micro USB socket and put the other end into a standard USB power outlet such as laptop or desktop 2 I
5. 88 or 1234 If pairing has failed power off Ranger ATO200 and redo the pairing process according to above mentioned procedures Ranger AT0200 can remember 8 paired devices When the number of paired devices exceeds 8 the first one will be replaced Each time Ranger AT0200 powers on it will connect to the last connected device automatically If you want to pair it to other devices turn off the current device s Bluetooth function first and try to pair the receiver to the new device according to above mentioned pairing procedures 7 2 LED indicator instruction LED indicator Status of Ranger AT0200 under RX mode Blue and red LEDs blink alternately and p Pairing mode lasts for 2 minutes continuously Blue LED flashes every 1 sec Standby mode not connected with a device Blue LED flashes twice every 4 seconds Connected with a device Red LED blinks Low power 7 3 Get maximum stable range Please kindly make sure there is no obstacle wall corner etc between receiver and transmitter www ranger technology com Dispose of the packaging and Dz this product in accordance with Same the latest provisions QDID B015006 FCC ID WJ5 BTTC200 Z PKMN TC200X 0378 ee LE
6. Do not place or keep this device near any heat source such as direct sunlight radiators stoves or other apparatus which produces heat It may cause explosion degrade the performance and or reduce battery life Do not modify repair or disassemble the device especially battery it may cause an explosion Doing so will void the warranty Do not place heavy objects on the device Use only supplied USB charging cable Service must be done by qualified service center or manufacturer Unplug this device when unused for long periods of time or during lightning storms CAUTION ELECTRIC SHOCK HAZARD The battery used in this device may present a risk of fire or chemical burn if mistreated Mit B09 BER MI HL HANEN size W420 x H150 mm F iPhone will auto scan for available Bluetooth devices Click Ranger AT0200 from the list of devices shown tap Yes or Confirm accordingly G After successful pairing and get connected the blue LED will blink twice every 4 seconds Receiving Press around 7 seconds till red Push button to RX Ranger AT0200 FAN _ 6 gt x C ex 2 Pairing 3 5MM Jack S Q PIN 0000 or Tap connect XM Note Pairing mode will last 2 minutes The receiver will enter standby mode if no devices can be connected within 2 minutes Ranger AT0200 receiver can pair with stereo Bluetooth devices using PIN code 0000 1111 88
7. h different mobile phones or other compatible Bluetooth devices usage settings usage styles and environments 11 10 Safety information e To avoid any damage or malfunction of the device do not drop device from high places e Keep device away from humidity water or any other liquid If the device is exposed to water moisture or other liquid do not operate it to avoid any electrical shock explosion and damage to the device or yourself e Do not place or keep this device near any heat source such as direct sunlight radiators stoves or other apparatus which produces heat It may cause explosion degrade the performance and or reduce battery life e Do not modify repair or disassemble device at discretion especially battery it may cause an explosion Doing this will void the warranty e Do not place heavy objects on the device e Use only supplied USB charging cable e Replacement or service must be done by qualified service center or manufacturer Unplug this device when unused for long periods of time or during lightning storms CAUTION ELECTRIC SHOCK HAZARD The battery used in this device may present a risk of fire or chemical burn if mistreated Note 1 Ranger AT0200 blue LED will flash 3 times within 4 seconds after connection with another Bluetooth device which also supports the aptX codec Both transmitter and receiver are incorporated with aptX codec it will help low latency and higher audio quality compare with
8. standard Bluetooth audio 2 The pairing mode will last 2 minutes Ranger AT0200 will enter standby mode if no devices can be connected within 2 mins 3 Ranger AT0200 can pair with stereo Bluetooth receiver devices using PIN code 0000 1111 8888 or 1234 LED indicator instruction We find most problems are caused by improper pairing 6 Receiver turn On Off Push the click button to RX mode from TX RX position before power on TX or RX mode cannot be changed after powering on Ranger AT0200 Turn On press and hold Ranger AT0200 MFB button for around 5 7 seconds until the blue LED is on for 1 second Turn Off press and hold Ranger AT0200 MFB button for around 3 4 seconds until the red LED is on for 1 second and then goes off 7 Receiver pairing with a Bluetooth device 7 1Pairing procedure A Plug the 3 5 mm audio cable into Ranger AT0200 3 5 mm audio socket Plug the other end or 2 x RCA into the audio input of your home hi fi stereo system B Ensure Ranger AT0200 has pushed into RX mode and the device is off C Put Ranger AT0200 and your Bluetooth enabled phone within 1 meter D Press and hold Ranger AT0200 MFB button for around 6 8 seconds until the blue and red LEDs blink quickly and alternatively indicating it is in pairing mode E Make your smartphone into Bluetooth mode Taking an iPhone as an example From your iPhone home page tap Settings General Bluetooth
9. t takes 3 hours to charge fully and reach its full capacity for the first time Each subsequent charge cycle take around 2 hours 3 LED will indicate red when charging and goes off when charging is complete 4 If you have not used the device for a few months LED might not turn red when first charging It might take 15 35 minutes before the LED turns red 5 We suggest fully charging the device at least once every two months aoe How to get the maximum range 8 Advanced functions 8 1 Streaming music When Ranger AT0200 is used as a receiver you can connect it to a 3 5mm stereo headset or stereo speaker with a 3 5mm to 3 5mm audio cable You will be able to listen to music and control pause play of music Playing music After short press MFB button once will pause the music Pausing 8 2 Charging and streaming music After short press MFB button once will play the music When battery is low but you still want to use Ranger AT0200 in TX or RX mode you can charge the device and stream audio sound simultaneously 8 3 Reconnecting to a Bluetooth device A Automatic connecting Once Ranger AT0200 is powered on it will automatically connect with the last connected device B Manual connecting When Ranger AT0200 is in standby mode and doesn t connect to any device short press MFB button once and it will automatically connect to the last connected device 410 j eee eB ee Be ee eg Be MP Be eB eB eB eB BP eB eB
Download Pdf Manuals
Related Search