Spec Sheet - Western Environmental Canada
Contents
1. ai A HACC meu EEE EEE I 100 Viscosity in Centistokes 65 F as o A 1000 Figure 6 Chart of Approximate Scale Factors for Fluids of Different Viscosities Water Anti Freeze Scale Factor 1 044 1 007 ATF 1 000 1 002 0 999 0 993 Table 2 Samples of Fluids Viscosities and Scale Factors 10000 November 2012 Installation amp Operation Manual CHANGING FACTORY SETTINGS Each meter is calibrated at the factory for use with motor oil refer to the Change Scale Factor section of this manual The Unit of Measure is also selected prior to shipment Verifying Firmware Version To check the firmware version and code checksum press and hold the TOTAL and 1 buttons at the same time The last two digits on the lower right are the firmware version Using the Programming Feature Use the Programming feature to change the factory settings Push the AUTO and TOTAL buttons at the same time and hold for 2 seconds to bring up the Program PIN screen To enter your PIN 1 Press and hold the 10 button to select first digit of PIN 2 Press and hold the 1 button to select second digit of PIN 3 Press and hold the 0 1 button to select third digit of PIN 4 If necessary hold down the TOTAL key and press 10 1 or 0 1 to decr2. Consult the factory for the sequence The AUTO icon displays indicating the meter is in the EPM Mode The solenoid valve unlocks and the meter can now be used as a Standard Preset Batch Meter NOTE The AUTO button is used to toggle between Manual Mode and Batch Mode EPM Manual Mode Pull the trigger to begin the flow The display shows the amount dispensed When the desired amount has been dispensed release the trigger to stop the flow Press the RESET button once to reset the counter display to zero Amount Dispensed EPM Batch Mode To enter the Batch Mode from the Manual Mode press the AUTO button E ES When in the Batch Mode the batch quantity displays in the lower right hand corner of the screen AUTO D The meter is now in Batch Mode Batch Quantity 1 Change the batch size by pressing the 10 1 and or 0 1 buttons VS QT a Pressthe 10 button to increase the batch amount in increments of 10 units LI 43 LI b Press the 1 button to increase the batch amount in increments of 1 unit c Press the 0 1 button to increase the batch amount in increments of 0 1 units 2 Pull the trigger to begin the flow The meter solenoid valve automatically locks the dispensing valve in the full open position A Size The trigger falls back to the closed position The meter always locks in the maximum open position After the batch quantity is dispensed the flow automatically shuts off NOTE ForRF and BAT
3. Germany 49 7025 9208 0 Czech Republic Badger Meter Czech Republic s r o Maf kova 2082 26 621 00 Brno Czech Republic 420 5 41420411 Slovakia Badger Meter Slovakia s r o Racianska 109 B 831 02 Bratislava Slovakia 421 2 44 63 83 01 Asia Pacific Badger Meter 80 Marine Parade Rd 21 04 Parkway Parade Singapore 449269 65 63464836 China Badger Meter Rm 501 N 11 Longyue Apartment N 180 Longjin Rd Jiuting Songjiang District Shanghai China 201615 86 21 5763 5412
4. ga a eine idea 12 EPM Manual Mode em pe a a TET T ET e cines at mt ae A pd IO a ee T eee ee 12 EPM Pale Mode a pda Raiden 12 Ret mi to RF MOGE 45 ee 99 391959 372 79 994 99 pat a ee ADA ee A 13 OPERATING MODE FUNCTIONS 4 e 454544464565 EXE Ra eA RRA 14 Resettable Accumulated Totals 14 Emergency Override api FT RHE GAY 52395 24 335 33 99923235444 9 93 543733 14 CALCULATING THE SCALE FACTOR ae osia eomm ok ce ia a OE ew na 15 Viewing the Current Scale Factor 15 Absolute Scale Factor a ung aca are d PT TTT TTT TE Eee de An eee ae 15 CHANGING FACTORY SETTINGS e e i ma 3 3c9 9 933 9 99443 393999 99325299 242353 17 Verifying Firmware Version uu 4005 din ted A d 17 Using the Programming Feature ee ee ene 17 Changing the Unit of Measure 17 Changing the Scale Factor ea aa ev 39 wees RS Wes TE RES GEES HEH ESRD EE 18 Verifying Changes i es aux oe ha Ur qo P ee OREO ai d a eee eh AE OR ek d P 18 Enabling or Disabling the EPM Manual Mode o o o ooo ooo e 18 rod os AA 19 Power Level Display vv uw woes 3E COR de see SE E Para b d rta 19 November 2012 Page iii Electronic Preset Meter Model EPM 3 RF 2 4 GHz DIMENSIONS ss Do e e P d RARE O on lo dog Sa ae AAA 20 SPECIFICATIONS 4446480 pie d a aa de LIRE URRA 20 PART LIOF ero ie cca e se a aa voor RU P Hea n ae da d PUR a Rhee PNE UR eas 21 TROUBLESHOOTING Vana Rae dO Sl da a eeu teu Gee oe A ae Ale io ee
5. CH programming the meter automatically shuts off if the trigger is pulled and the meter does not sense any flow Also in case of an emergency or to interrupt a batch the meter is equipped with an Emergency Override Refer to the Emergency Override on page 14 section of this manual Page 12 November 2012 Installation amp Operation Manual Return to RF Mode To return to the RF Mode from the EPM Mode 1 If the batch quantity on the display is not zero press the RESET button to zero the display 2 Press the RESET button with a zero batch quantity on the display You ll see the flashing arrows indicating the meter is communicating with the RF System Arrows 3 When communication is complete the meter returns to the RF Mode and the trigger locks To manually reset the meter to the RF Mode 1 If the batch quantity on the display is not zero press the RESET button to zero the display 2 Re enter the Manual Mode key sequence November 2012 Page 13 Electronic Preset Meter Model EPM 3 RF 2 4 GHz OPERATING MODE FUNCTIONS These functions operate the same in RF Mode and EPM Mode Resettable Accumulated Totals The meter has two flow totalizers One is Resettable Total the other is Accumulated Total 1 Press and hold the TOTAL button to see the Accumulated Total Ww c i L 2 Continue holding the TOTAL button for three seconds to see the Resettable Total A RESETTOTAD RESETTOTAL displays the total fluid d
6. Electronic Preset Meter Badger Meter Model EPM 3 RF 2 4 GHz IOM 197 02 EN November 2012 pide Installation 8 Operation Manual Electronic Preset Meter Model EPM 3 RF 2 4 GHz Page ii November 2012 Installation amp Operation Manual CONTENTS SAPEDE Gas aw deen FRITTATA 5 Explosion and Fire Hazard 3 ee dew ee ee EGRE de dn e i ina heen cl nat dle S UR dn d SR A a Jeni oa ded a 5 Meter Hazas surrender ARAN d A SUA A Aaa A d aa E GRE 5 ELECTRONIC PRESET METER DESCRIPTION s a cete pecete ii anar cr Sox aa 6 DISCIANNGh alia RR 6 Product Identification Information ss e ceea ae yi a e aaa e e ne 6 CEFIN CATIGA ou pete e i ae E e de ci rro or eae Ge e dp Anale ge ap E ee EG EOS d cae AI di de ees 6 OPERATION cabin ri mati 7 Meter BULION Sa sensor sealed rain ein 7 UCD IDISDIAV 4 42a de Rak Anni 7 MIETERINSPAELEATION 2424244 442645 54 sl ille 8 Relieve System Pressure usas Guido eae gene and ai e Peewee NR 8 GIOUNGINO asian inerenti 8 FUSANO TIOCCOUlG sa ae va ne st a te c 60 e annie Rien 8 Apply Meter to Hose n at ar e tate e ai a ce SEU OSE EE Gu SETE 9 Apply Nozzle to Meter o n ee mia des wy oe e RY RO X 9 3 9 9 9 xxu HODES ai 9 METER OPERATION RF MODE 24 e 2048 dae ER eR OR E oe ka arie eS ee SEE AA 10 Connecting to an FMS Network as uw x dedos ee oi TIRI 10 o cessi 11 ERO COCOS 4 444 An ee U4 G Ae eee PNE MAG PAURA E ERR a do a ea 11 METER OPERATION EPM MODE 6 x2 ok duca mit ache
7. OT exceed the maximum working pressure level of the lowest rated system component Use only extensions and nozzles that are designed for use with this equipment Use only fluids and solvents that are compatible with the equipment Read all fluid and solvent manufacturer s warnings Tighten all fluid connections before operating this equipment Do NOT stop or deflect leaks with hands body gloves or rags Do NOT dispense towards any person or any part of the body Do NOT place hands or fingers over the end of or into the dispense valve Comply with all local state and federal fire electrical and safety regulations Use of this product in a manner other than specified in this manual may result in impaired operation or damage to equipment November 2012 Page 5 Electronic Preset Meter Model EPM 3 RF 2 4 GHz ELECTRONIC PRESET METER DESCRIPTION Disclaimer The user purchaser is expected to read and understand the information provided in this manual follow any listed Safety Precautions and Instructions and keep this manual with the equipment for future reference The information in this manual has been carefully checked and is believed to be entirely reliable and consistent with the product described However no responsibility is assumed for inaccuracies nor does Badger Meter Inc assume any liability arising out of the application and use of the equipment described Product Identification Information Record the product identificatio
8. ash when RF communication is in progress with the keypad 4 Preset Batch quantity 5 History Icon 6 AUTO is an indicator of being in EPM mode 7 Low Battery Icon November 2012 Page 7 Electronic Preset Meter Model EPM 3 RF 2 4 GHz METER INSTALLATION Relieve System Pressure 1 Turn off the power supply to the pump or close the shutoff valve 2 Dispense any fluid in the system into a waste container by opening the meter s 3 Open all bleed type master air valves and fluid meter s in the system 4 Leave the meter s open until ready to pressurize the system Pressurized Equipment This equipment stays pressurized until the pressure is manually relieved To reduce the risk of injury from fluid spray from the meter follow the Pressure Relief Procedures when you e Areinstructed to relieve pressure e Stop dispensing e Check clean or service any system equipment e Clean or install nozzles Grounding Grounding reduces the risk of static soarking Ground all system components according to local state and federal codes Consult the pump user s manual and other system components to ground the following e Pump follow manufacturer s recommendations e Air and Fluid Hoses use only grounded hoses e Air Compressor follow manufacturers recommendations e Fluid Supply Container follow the local code Possible Explosion and Fire Movement of fluids through the dispensing system creates static electricity Static e
9. battery compartment is located in the lower case on the backside of the trigger guard 1 Position the unit face down 2 Unscrew the two screws Remove the battery door to expose the batteries 3 Replace the old batteries with 4 AA alkaline batteries NOTE Battery polarity markings are inside battery compartment 4 Dispose of used batteries properly according to local regulations NOTE Changing the batteries does not affect any of the programmed values or totals November 2012 Page 25 Electronic Preset Meter Model EPM 3 RF 2 4 GHz INTENTIONAL BLANK PAGE Page 26 November 2012 Installation amp Operation Manual INTENTIONAL BLANK PAGE November 2012 Page 27 Trademarks appearing in this document are the property of their respective entities Due to continuous research product improvements and enhancements Badger Meter reserves the right to change product or system specifications without notice except to the extent an outstanding contractual obligation exists 2012 Badger Meter Inc All rights reserved www badgermeter com The Americas Badger Meter 4545 West Brown Deer Rd PO Box 245036 Milwaukee WI 53224 9536 800 876 3837 414 355 0400 M xico Badger Meter de las Americas S A de C V Pedro Luis Ogaz n N 32 Esq Angelina N 24 Colonia Guadalupe Inn CP 01050 M xico DF M xico 52 55 5662 0882 Europe Middle East and Africa Badger Meter Europa GmbH Nurtinger Str 76 72639 Neuffen
10. cks and the batch quantity is displayed 3 Pull the trigger to the full up position to begin the fluid flow e The solenoid valve automatically locks the dispensing valve in the full open position The trigger falls back to the closed position It is not necessary to continue to hold the trigger Batch Quantity After the batch quantity is dispensed the flow automatically shuts off Do NOT press the RESET button before topping off If the RESET button is pressed the meter returns to a locked out position and does not allow additional fluid to be dispensed until a valid dispense order is received from the RF system 4 You have the option to top off the tank after the batch quantity has been dispensed a Totop off pull the trigger to begin the flow b Releasethe trigger when the desired amount has been dispensed 5 Pressthe RESET button when finished to complete the dispense order a Thetotal quantity dispensed is transmitted to the RF system b Themeter returns to the locked position C The meter is now ready to receive another dispense order from the RF system NOTE Ifthe original communication fails the meter automatically attempts to communicate with the RF system by resending the Dispense Result three times 30 seconds apart 6 Ifthe meter is unable to communicate a dispense result the History icon lights Page 10 November 2012 Installation amp Operation Manual History Icon The History icon indicat
11. el connections are either 1 2 NPT or 1 2 BSPP depending on meter model Apply Nozzle to Meter On the opposite end apply sealant to the end of the nozzle Recommended sealant is Loctite 243 Thread the nozzle onto the meter Screw it in tightly with an open ended adjustable wrench Open all dispense position shut off valves Start the pump to pressurize the system Before use to ensure accuracy purge all air from the fluid lines and dispense valve s November 2012 Page 9 Electronic Preset Meter Model EPM 3 RF 2 4 GHz METER OPERATION RF MODE Connecting to an FMS Network When the meter is first installed it must be attached to the network with the keypad powered ON Also when the keypad is replaced the meter must be reconnected 1 Press and hold the 10 key 2 While holding down the 10 key press and release the RESET button The meter will then search for and connect to the network When the battery pack is attached to the meter it automatically enters the RF Mode The trigger is in the locked out position No fluid can be dispensed by the meter until a dispense order is received from the keypad 1 Pressing the meter RESET button causes communication to occur between the meter and the keypad Two arrows in the lower right hand corner of the meter screen flash This indicates communication is in progress between the meter and keypad Arrows 2 When the communication is complete the trigger unlo
12. ement a PIN digit 5 Press RESET to confirm PIN and enter the programming mode with Scale Factor and Unit of Measure screen displayed 6 Pushand hold AUTO and TOTAL for 2 seconds to exit the programming mode Changing the Unit of Measure The meter has four Units of Measure e Pint PT Quart OT e Gallon GAL e Liter L Changing the Unit of Measure from metric to English or from English to metric clears the Resettable Total and the Accumulated Total The current Unit of Measure is flashing when you enter the Programming Mode To change the Unit of Measure 1 Press and hold the TOTAL button until the Unit of Measure you want is displayed 2 Press the RESET button to save your selection 3 Ifyou select L Liters the decimal point begins to flash Press the TOTAL button to change the decimal point to either a period or a comma 4 fnoScale Factor changes are necessary press and hold the TOTAL and AUTO buttons until the display flashes three times then goes blank OR Press the RESET button to advance to the EPM Manual Mode Enable screen November 2012 Page 17 Electronic Preset Meter Model EPM 3 RF 2 4 GHz Changing the Scale Factor IMPORTANT Changing the Scale Factor changes the accuracy of the meter potentially causing over dispensing or under dispensing of the liquid This has the potential to cause a mechanical breakdown Scale Factor Digits 1 Press the RESET button to advance th
13. es there is dispense result information that has not been communicated to the keypad to complete a work order To send the dispense result information to the keypad press the RESET button to initiate communication History Icon Error Codes The meter has several Error Codes that may display These provide indication at the meter that there is an error in communication between the meter and keypad The meter radio is not working To clear the error press the RESET button on the meter The meter is not configured to a keypad To clear the error code press the RESET button on the meter Verify that the meter radio address is configured properly System busy To clear the error press the RESET button on the meter Meter lost connection to network Out of range network connection lost Keypad not powered Meter moved out of range of keypad Meter not connected to a network First time being powered up Network selected is not available SFO The Scale Factor setting for the meter is set to 0 000 Scale Factor 0 To input a valid Scale Factor for the meter follow the instructions in the Change Factory Settings section of this manual All other Are for factory purposes only Error Codes To clear the meter press RESET November 2012 Page 11 Electronic Preset Meter Model EPM 3 RF 2 4 GHz METER OPERATION EPM MODE The meter can be put in EPM Mode for startup purposes by entering the Manual Mode key sequence
14. ispensed since the Resettable Total was last set back to zero 3 Press the RESET button while viewing RESETTOTAL to set it back to zero 4 Release the TOTAL button to return to the operating display Resettable Total NOTE The Accumulated Total cannot be reset unless the you change the unit setting from English units to metric units or from metric to English units Refer to the Change Factory Settings Change Unit of Measure section of this manual Emergency Override In case of an emergency or to interrupt a batch the meter is equipped with an Emergency Override 1 Press the red O button to activate the Emergency Override The override closes the valve immediately stopping fluid flow 2 Batching can continue after an Emergency Override by pulling up on the trigger Page 14 November 2012 Installation amp Operation Manual CALCULATING THE SCALE FACTOR A Scale Factor is a number used to adjust meter accuracy The Scale Factor is set at the factory using motor oil with a viscosity of 10W The primary use for Scale Factor recalibration is to batch fluids with different viscosities If the fluid has a lower viscosity more fluid can slip past the meter gears without being detected Changing the Scale Factor adjusts the meter to compensate for the loss The meter multiplies each pulse by the Scale Factor number to correct the accuracy when it converts to the specified units The reading is then always correct For an appr
15. lectricity can cause volatile fumes resulting in an explosion and fire The dispensing system must be grounded Flushing Procedure NOTE If the system has multiple dispense positions begin at the position farthest from the pump and move towards the pump If this installation is new or if the fluid in the lines is contaminated flush the system before installing the meter s 1 Close fluid dispense valves at every position 2 Oncethe main fluid outlet valve at the pump is closed the air pressure to the pump motor is properly adjusted and the air valve is opened Slowly open the main fluid valve Place the hose end in a waste container Make sure hose is secure so no fluid leaks during flushing Slowly open the dispense valve and allow enough oil to pass through it to ensure that the system is clean e ur d MP Close the valve and repeat for all dispense positions Page 8 November 2012 Installation amp Operation Manual Apply Meter to Hose Close the drain valve before starting this procedure 1 Attach a swivel to the meter Apply thread sealant to the male end of hose Recommended sealant is Loctite 243 2 Insert the metal end of the hose into the swivel Tighten completely with an open ended adjustable wrench NOTE The threaded end of the meter always has female threads The metal end of the hose must have male threads Apply thread sealant Loctite 243 or equivalent to the male end The inlet and outlet swiv
16. n Part Number Page 22 November 2012 Installation amp Operation Manual fh N EDON IN RG BNO neme Description PartNumber November 2012 Page 23 Electronic Preset Meter Model EPM 3 RF 2 4 GHz TROUBLESHOOTING Pressurized Equipment Relieve the pressure prior to checking or repairing the meter Make sure all valves controls and pumps are operating correctly Battery Icon is Batteries are low Replace batteries displayed Display Blank Press RESET button Loose battery connection Remove battery pack and check battery connection Press RESET button Batteries dead Replace batteries e Press RESET button Meter does not latch Meter not in AUTO mode Press AUTO button and program batch size for batching Meter not reset after prior batch Press RESET button Low batteries e Check for battery icon Replace batteries e Press RESET button Page 24 November 2012 Installation amp Operation Manual MAINTENANCE Low Battery Indicators When the batteries need changing a progression of warnings appears on the meter screen First Warning QT The Low Battery icon appears in the lower left corner of the display That means the odiis batteries are low and need to be changed when the icon appears Second Warning The Battery icon flashes The battery power is too low and meter functions are disabled Low Battery Icon Changing the Batteries The
17. n N AN ee eae ac 24 MAINTENANCE 4 4459 2694465500 PRIORI d OT EDEN URE OSS OER Oe A 25 Low Battery INGICALOIS s Largo RUP cit tooo eae cd ACE EP sp apele P E NM S s ee eee eee ii eS 25 Changing the Batteries 4 ex 24 8 645 64664 eb OE EES Vd SEWUESSS Wu PRAG S LEA 25 Page iv November 2012 Installation amp Operation Manual SAFETY Explosion and Fire Hazards Improper grounding poor ventilation open flames or sparks can cause a hazardous condition and result in an explosion or fire and cause serious injury Be sure the fluid system is properly grounded See your pump instruction manual for details If there is static sparking or if you feel an electric shock while using the meter stop dispensing immediately Identify and correct the problem before continuing Provide fresh air ventilation This will avoid the buildup of fumes from the fluid being dispensed Do not smoke while dispensing flammable fluids Keep the dispensing area free of debris including solvents rags and spilled gasoline Meter Hazards Equipment misuse can cause the meter to rupture or malfunction and cause serious injury This equipment is for professional use only Read all instructions tags and labels before operating the equipment Use the equipment only for its intended purpose Do NOT modify or alter the equipment Do NOT leave equipment unattended while dispensing Check equipment daily Repair or replace worn or damaged parts immediately Do N
18. n numbers from the nameplate here Model Number Serial Number Tag Number if applicable Certification e Contains FCC ID SAGEM35XB e Contains IC 8735A EM35XB FCC CERTIFIED PART 15 SUB PART C CE0681 EC R amp TTE Certified This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation To satisfy FCC RF exposure requirements for mobile transmitting devices a separation distance of 20 cm or more should be maintained between the antenna of this device and persons during operation To ensure compliance operations at closer distances than this are not recommended Page 6 November 2012 Installation amp Operation Manual OPERATION The Electronic Preset Meter RF3 EPM RF3 is equipped with RF radio frequency communications to communicate with a fluid management system keypad to get authorization and dispense information This is referred to in the manual as the RF Mode The meter can also be run as a standard EPM This is referred to in the manual as the EPM Mode This is intended for start up purposes or when the fluid management system is not in use Once a work order has been entered at the keypad the operator simply pushes the RESET button on the meter to start communications between the meter and the ke
19. oximate Scale Factor for fluids of different viscosities consult the charts on the next page NOTE The meter s original Scale Factor was written on the trigger when it was calibrated at the factory It may have been revised after field installation Use the Scale Factor showing on the display not the one written on the trigger IMPORTANT Changing the Scale Factor changes the accuracy of the meter potentially causing over dispensing or under dispensing of the liquid Viewing the Current Scale Factor To view the current Scale Factor press and hold the TOTAL button and the AUTO button at the same time Absolute Scale Factor For absolute Scale Factor perform this test 1 Runa measured amount of fluid through the meter 2 Ifthe meter delivers 4 20 quarts and the display shows only 4 00 quarts then the Scale Factor needs to be adjusted 3 Divide what the meter delivered 4 20 by what the display shows 4 00 You get an error factor of 1 05 The existing Scale Factor is 1 0123 4 Tocalculate a new factor 1 0123 existing Scale Factor x 1 05 error factor 1 0629 new Scale Factor 5 Enter that number as described in the Change Scale Factor section of this manual NOTE Use the Scale Factor showing on the display not one written on the trigger November 2012 Page 15 Electronic Preset Meter Model EPM 3 RF 2 4 GHz Page 16 Scale Factor 1 06 1 04 4 1 01 4 0 99 4 0 98 Scale Factor
20. rough the Scale Factor digits 2 Press the TOTAL button to change the selected number NOTE All digits can be scrolled between 0 and 9 except the first It can only be scrolled from 0 to 1 or from 1 to 0 3 Press the RESET button advance to the next number in Scale Factor Unit of Measure ZEN Scale Factor Digits 4 Repeatsteps 2 and 3 for all five digits in Scale Factor If no Scale Factor changes are necessary press and hold the TOTAL and AUTO buttons until the display flashes three times then goes blank OR Press the RESET button to advance to the EPM Manual Mode Enable screen Verifying Changes Press and hold down the TOTAL and AUTO buttons at the same time to verify that the Scale Factor is correct Enabling or Disabling the EPM Manual Mode To enable or disable the EPM mode 1 Pressthe RESET button to advance to the AUTO icon on the display There will be no other icons flashing on the display 2 Pressthe AUTO button to toggle the AUTO icon on and off When the icon is turned on the meter can be put in EPM mode through the special key sequence on the meter keypad When the AUTO icon is turned off the key sequence is disabled and the meter cannot be put in EPM mode 3 Press the RESET button to advance to the Network Program screen Page 18 November 2012 Installation amp Operation Manual Network Program The Radio Network is used to differentiate multiple FMS networks For standard installa
21. tions the default setting of zero will not need to be changed The Network setting must be between 0 and 255 To change the network setting 1 Press 1 to increment network setting or press 0 1 to decrement network setting 2 Press RESET to advance to the Power Level Display screen NOTE When NOT in programming mode you can view the Radio Network by holding down the TOTAL button while pressing the 10 button Power Level Display 1 The radio power level is set at the factory The display is for validation purposes only 2 Press RESET to return to Scale Factor and Unit of Measure screen NOTE When NOT in programming mode you can view the Power Level by holding down the TOTAL button while pressing the 1 button Saving Changes To save your changes and exit the programming mode 1 Press and hold down the TOTAL and AUTO buttons at the same time The display will flash 3 times and go blank 2 Press the RESET button to turn on the display November 2012 Page 19 Electronic Preset Meter Model EPM 3 RF 2 4 GHz DIMENSIONS Pia 7 0 SPECIFICATIONS Tested with DTE 25 motor oil at ambient temperature Minimum maximum flow range will vary with fluid viscosity Page 20 November 2012 Installation amp Operation Manual PARTS LIST heme Description Partnumber November 2012 Page 21 Electronic Preset Meter Model EPM 3 RF 2 4 GHz ems Descriptio
22. ypad The meter receives authorization from the keypad to unlock and the dispense batch quantity When the trigger is pulled the preset dispense batch quantity dispenses The meter automatically shuts off when the dispense batch quantity has been reached A Topoff feature allows additional fluid to be dispensed and tracked after the batch quantity has been dispensed Upon completion of the dispense the operator presses the RESET button The meter then locks prohibiting any unauthorized dispense of fluid to occur and the dispense quantity is sent to the keypad Meter Buttons 10 1 0 1 Used to enter the dispense Batch quantity when cn in the EPM Mode These buttons are NOT used in RF Mode TOTAL Used to display the accumulated total of fluid dispensed as well as the re settable total AUTO Used to enter and exit the manual or batch mode when in EPM mode This button is NOT used in RF mode RESET e Used to initiate RF communications from the meter to the Keypad ae RESET OTA RES Used in EPM mode to clear the previous batch Used to reset the re settable total dispensed while pressing the TOTAL button SHUTOFF Used to stop the flow through an Emergency or Override STOP LCD Display 1 2 1 Displays resettable total accumulated total and scale factor 2 Displays unit of measure 3 Arrows fl
Download Pdf Manuals
Related Search