3 - Solaxx Water Treatment Solutions
Contents
1. The chlorine output is controlled by the adjustment of the Timer of the power supply The Timer rl Cyanuric Acid 50 5 ppm regulates the hours per day of the amount of ON time the system requires to maintain the chlorine residuals as required The output is only regulated according to the chlorine Timer It operates independently from your filter pump run time Hours per Day Power Supply Control Panel NOTE Any interruption of power will cause the current memory cycle to reset itself when power is restored CHLORINE ADJUSTMENT After everything is setup the display will show you a default screen with the current hours of operation per day You may change this setting anytime by holding down the for 3 seconds straight See Fig 3 The display will flash indicating it is now ready for time setting changes In order to determine the proper chlorine timer setting for your spa measure the free chlorine level every couple of days during the first few weeks Adjust the timer accordingly to achieve 3 0 4 0 PPM of Free Chlorine It is advised to check the chlorine level at least once a week to make sure the spa is properly sanitized Weather bather load and sunlight have a major influence on the chlorine demand of the spa water Recommended Spa Water Conditions Salt Level a 3000 p m Note If the spa has reached an undesirable amount of chlorine it is recommended to unplug Free cid D a eae 2 4 0 ppm the Saltron MINI unit power2. by Green normal operation mode No action is needed default light 6 HI and Red light 1 salt level high No action is needed Stop adding salt to water if you are doing so Hours 05 by 2 water temperature Using MINI for water temperature above 110 F or 45 C is not recommended default high alternatin 7 HI Red light 1 salt level too high You will have to dilute your spa water with fresh water until the salt level is less than blinking 3000 ppm 2 water temperature too Stop using MINI until water cools down high 3 short circuit in Check to make sure there are no metal objects caught in between electrode plates chlorinator cell 8 88 blinking All lights Power supply failure Unplug and plug in the power cord to reset the power supply If the problem persists blinking call customer service Symptom in Spa Water 9 chlorine level is low Hours set too low Adjust the hours setting to higher number the maximum is 24 hours day Make sure cyanuric acid level in your spa is between 50 80 PPM 10 chlorine level is too high Hours set too high Adjust the hours setting to lower number the minimum is O hours day
3. g 170 9 SPA SIZE CALCULATION Use these three formulas to calculate the volume of water in the spa Rectangular Length Ft x Width Ft x Average Depth Ft x 7 5 Total U S Gallons Length M x Width M x Average Depth M x 1000 Total Litres Round 3 14 x Radius Ft x Radius Ft x Average Depth Ft x 7 5 Total U S Gallons 3 14 x Radius M x Radius M x Average Depth M x 1000 Total Litres Free Form Average Length Ft x Average Width Ft x Average Depth Ft x 7 5 Total U S Gal Average Length M x Average Width M x Average Depth M x 1000 Total Litres UNIT MAINTENANCE Inspecting the Cell The cell should be inspected every 3 months Unplug the Saltron MINI from the GFCI socket Inspect the cell for scaling white sugar like deposit If scaling exists the cell should be cleaned Cleaning the cell To clean the cell a bucket or a large cup should be used The bucket should be filled with 80 water and 20 muriatic acid NEVER ADD WATER TO ACID only acid to water It is recommended to wear safety goggles when handling the acid Place the entire cell into the bucket for 20 minutes Remove the cell and do the inspection again If the scaling remains repeat the process After the scale is removed rinse the cell with fresh water See Fig 4 Te 20 min 80 H20 20 HCI ill 4a 4b SPA CHEMISTRY CHART The Saltron MINI system is designed to autom
4. supply from the GFCI socket Check chlorine levels each day Stabila G A Acid 50 80 ppm until the desired level is achieved Plug the power supply back into the GFCI socket once the chlorine level is within the desired limit SALT REQUIREMENT The best salt is a food quality granulated salt a 99 9 pure salt or solar salt These types of salt should be purchased from a pool store and are designed for use with chlorine generators Do not use rock salt iodized salt or salt with anti caking additives Do not use salt with more than 1 yellow prussiate of soda The optimum salt level is between 2000 2500 ppm Use the chart below to determine the amount of salt for your spa The column on the left is the amount of water in your pool The column on the top is the current salt level measured in your pool Always check your salt level before adding salt to the pool even if this is your first time Prior use of liquid chlorine and tablets could have caused an increase in salt levels Salt should not be removed from the spa water unless the salinity exceeds 4000 ppm or the salinity of the water is undesirable The only way to remove salt is by draining the water and adding fresh water NOTE Turn Saltron MINI unit off before adding sodium chloride and other chemicals and wait until complete dissolution before turning it on Salt Table I Amount of salt needed to achieve 2500 ppm level in your spa Spa Size in Gallons Salinity ppm measured in S
5. PA Liters 500 1000 1500 2000 2500 3000 100 Gallons 378 Liters 2 1 lbs 1 7lbs 1 3lbs 0 8lbs 0 4 Ibs 0 0 1 0kg 0 8kg 0 6kg 0 4kg 0 2kg 200 Gallons 757 Liters 42lbs 3 4lbs 26lbs 1 6lbs 0 8lbs 0 0 1 9kg 1 6kg 1 2kg 0 8kg 0 4kg 300 Gallons 1135 Liters 6 3lbs 5 0lbs 3 8lbs 2 5lbs 1 3 Ibs 0 0 28kg 2 3kg 1 7kg 1 1kg 0 6kg 400 Gallons 1514 Liters 8 4lbs 6 7 lbs 5 0lbs 3 3lbs 1 7 Ibs 0 0 3 8kg 3 0kg 2 3kg 1 5kg 0 8kg 500 Gallons 1892 Liters 10 4 lbs 8 4lbs 6 3lbs 4 2lbs 2 1 Ibs 0 0 4 7kg 3 8kg 28kg 1 9kg 0 9kg 600 Gallons 2271 Liters 12 5 lbs 10 0 lbs 7 5lbs 5 0lbs 2 5 Ibs 0 0 5 7kg 4 5kg 3 4kg 2 3kg 1 1kg Salt Table Il Amount of salt needed to achieve 3000 ppm level in your Swim SPA Swim Spa Size in Gallons Salinity ppm measured in Swim SPA Liters 0 500 1000 1500 2000 2500 3000 1000 Gallons 3780 Liters 2 11bs 1 7 lbs 1 3lbs 0 8 Ibs 0 4 Ibs 0 0 1 0kg 0 8kg 0 6kg 0 4kg 0 2 kg 2000 Gallons 7570 Liters 42lbs 3 4lbs 2 6lbs 1 6 Ibs 0 8 Ibs 0 0 1 9kg 1 6kg 1 2kg 0 8kg 0 4kg 3000 Gallons 11350 Liters 6 3lbs 5 0lbs 3 8lbs 2 5 Ibs 1 3 Ibs 0 0 2 8kg 2 3kg 1 7kg 1 1kg 0 6kg STABILIZER CYANURIC ACID LEVELS Cyanuric Acid Stabilizer Conditioner Required Spa Size in Gallons CYA ppm Level Before Addition with uncovered outdoor spas only a Liters 30 45 60 75 Cyanuric aci
6. Saltron mini Operating INTRODUCTION Saltron MINI Spa Sanitation System produces a pure form of chlorine by electrolysis of salt NaCl in order to sanitize your spa water After the salt is converted to chlorine and the bacteria are killed the chlorine converts back to salt and this process is ongoing The salt concentration used is very low less then that in a human tear Chlorine output can be easily adjusted by the timer on the power supply unit The chlorine level in your spa can be checked by using a standard chlorine test kit One Saltron MINI unit can treat up to 600 gallons 2 200L of spa water or up to 2000 gallons Swim Spa water IMPORTANT SAFETY INSTRUCTIONS WARNING WARNING WARNING WARNING WARNING WARNING WARNING WARNING WARNING Risk of Electric Shock Connect only to a grounding type receptacle protected by a groundfault circuit interrupter GFCI Contact a qualified electrician if you cannot verify that the receptacle is protected by a GFCI Make sure the power supply is unplugged from the wall outlet when using spa To reduce the risk of injury or electric shock do not allow children to use this product Power supply should be installed in a shaded area to protect the transformer from direct sunlight Disconnectthe power supply from the outlet when not in use Do not operate with a damaged cord or power supply To avoid risk of electrical shock do not put the power supply i
7. atically generate the chlorine for your spa It is very important to note that chlorine is just one component of your spa water chemistry Please make sure your spa water meets the optimum chemistry levels in the following Spa Chemistry Chart FACTORS PREFERRED LEVELS 1 Salt 2000 2500 ppm 3000 ppm for Swim Spa 2 PH 7 4 7 6 3 Free Chlorine 3 0 4 0 4 Cyanuric Acid 50 80 ppm OPERATION MODE AND TROUBLE SHOOTING Saltron MINI Operation Mode and Trouble Shooting Symptom on Power Supply Possible Causes Solution Display LED 1 no display no lights 1 power outage Make sure there is power to the unit 2 fuse burnt Check and change the fuse if it s burnt 3 power supply failure Call customer service 2 Soe no lights MINI in rest mode No action is needed If you want it to operate immediately unplug plug the power or adjust the timer Both will start the operation right away 3 and no lights 1 chlorinator cell is Put it back into the water Hours 05 by outside water default 2 open circuit in Check the wire connections and make sure no cut or broken wire alternating chlorinator cell 4 LO and Yellow 1 salt level low Add more salt to spa and allow time for it to dissolve Hours 05 by light 2 water temperature low Don t use MINI if the water temperature is under 65 F or 15 C default 3 chlorinator cell at its Call customer service for replacement alternating life end 5 Hours 05
8. d CYA also known as stabilizer or conditioner prevents rapid breakdown of 100 Gallons 378 Liters 1 0 oz 0 8 oz 0 6 0z 0 4 oz 0 2 oz 0 0 chlorine by direct sunlight Maintain CYA 28 g 23 9 17 9 11 g 6 g concentrations between 50 80 ppm by diluting 200 Gallons 757 Liters 2 0 oz 1 6 oz 1 2 0z 0 8 0z 0 4 oz 0 0 with fresh water 57 9 45 g 34 g 23 g 11 g i 300 Gallons 1135 Liters 3 0 oz 2 4 oz 1 8 oz 1 2 0z 0 6 oz 0 0 Regulations may exist regarding use of 85 g 68 g 51 g 34 g 17 g Cyanuric acid in spas please consult with your 400 Gallons 1514 Liters 4 0 oz 3 2 02 2 4 02 1 6 oz 080 0 0 spa professional 113 g 91 9 68 g 45 g 23 9 Use the following chart to determine the amount 500 Gallons 1892 Liters 5 0 oz 4 0 oz 3 0 oz 2 0 oz 1 0 oz 0 0 i i i 142 9 113 9 85 9 57 9 28 g of Cyanuric acid needed Test water with a test 600 Gallons 2271 Liters 6 00z 4 802 3601 24oz 1207 0 0 kit that includes CYA testing then use the table j 170 9 136 9 102 9 68 g 34 9 below to determine the amount to add Note Indoor spas do not require the addition of CYA Swim Spa Size 1000 Gallons 3780 Liters 10 oz 8 0z 6 oz 4 oz 2 oz 0 0 280 g 230 9 170 9 110 9 60 g 2000 Gallons 7570 Liters 20 oz 16 oz 12 oz 8 oz 4 oz 0 0 570 g 450 g 340 g 230 g 110 g 3000 Gallons 11350 Liters 30 oz 24 oz 18 oz 12 0z 6 oz 0 0 850 g 680 g 510 g 340
9. ion of the Cell Holder Use the adhesive tape provided to anchor the CELL HOLDER to the spa skirt Another option is to directly attach it to the side of the Power Supply See Fig 2a 2c NOTE The Saltron MINI over the wall cell should be removed whenever the spa is in use After installing the CELL HOLDER simply hang the cell outside the spa inside the CELL HOLDER during spa use INSTALLATION AND OPERATION Operation of the Saltron MINI I Turn on the power to the spa equipment Il Turn on main spa pump 111 Add required type and amount of salt to spa Spread over the surface and allow salt to dissolve for at least 20 minutes IV Place the cell in the spa anywhere below the waterline preferably one foot under V Plug the Power Supply into an 110VAC 220 VAC GFCI protected outlet NOTE Be sure to test the chlorine level for the next few days and properly adjust the chlorine output by adjusting the Hours Per Day on the power supply front panel DO NOT EXCEED RECOMMENDED CHLORINE LEVELS Make the required adjustment and allow the spa to react to this change for a minimum of 2 days After 2 days retest the spa water and make any further adjustments as required until the Saltron MINI unit maintains an adequate Free Available Chlorine residual NOTE The Saltron MINI system works based on a natural convection of water nota forced convection as in in line systems This operation is independent of the main circulat
10. ion pump The cell must be submerged underwater for proper operation As the cell is energized to generate chlorine bubbles will appear and is normal If the cell is removed from spa water chlorine generation is automatically stopped N 1 Chlorinator Cell 2 Power Supply 3 Cell Holder 4 Plug 5 SPA 6 Water for salt levels see the SPA Chemistry Chart a a UT INSTALLATION AND OPERATION POWER SUPPLY FUNCTION 1 When the Power Supply is first plugged in All three LED lights and the display will be ON for approximately 3 seconds while the Saltron MINI unit self tests 2 Normal Operation If your Saltron MINI unit is operating properly the Green LED light will display solid GREEN and the display will show the operation hours per day This indicates that power is being delivered from the Saltron MINI unit to the cell and is producing sanitizer and your spa is being sanitized by Hypochlorous Acid chlorine NOTE While sanitizer is being produced bubbles can be seen 0 Chlorine Time O coming from the cell 3 Abnormal Conditions i A f f Recommended Spa Water Conditions further explanation of the abnormal conditions please refer to the Troubleshooting Guide Salt Level 2000 3000 p The LED lights will flash rapidly and or the display will also flash to indicate a problem or failure For 4 Chlorine Output Control Free Chlorine 1 9 ir rau le 0 4 0 pom
11. n the water To reduce the risk of electric shock do not use extension cords to connect unit to electric supply if necessary contact a qualified electrician to provide a properly located outlet Make sure the power supply is unplugged from the wall outlet when cleaning servicing the cell assembly SPECIFICATIONS Saltron MINI Power Supply Size For Spas or Swim Spas up to 2000 gallons INPUT 100 240 VAC 50 60 Hz 0 2 Amp OUTPUT 5 0 VDC 2 0 Amp 104 F 40 C Saltron MINI Cell Normal output equivalent to 1 1 oz 32 grams of free available chlorine per day Reverse Polarity Function The Reverse Polarity Function is designed to automatically clean the cell plates maximizing the cell s ability to manufacture chlorine INSTALLATION AND OPERATION Installation ofthe Power Supply Unit The power supply can be mounted to a wall next to the spa or directly on the spa wall The wall needs to have easy access to a GFCI socket In addition install the Power Supply Unit to a wall that ensures the least amount of direct exposure to rain garden sprinkler water direct sunlight When installing the power supply to the spa wall please use the stainless steel screws provided fasten the Power Supply Unit to the top of the spa skirt just below the acrylic lip Before tightening the screw adjust the height of the Power Supply Unit to make sure that the waterproof connector is outside of the spa water See Fig 1 Installat
Download Pdf Manuals
Related Search