User Manual CM, VM Space Saver
Contents
1. 6 switched 2 always on Y SURGEN Space Saver Manual 3 3 Remote Control Connections Remote control connections are wired to the green 7 pin plug in Phoenix terminal block on the rear of the unit next to the power cord The terminal block is shipped with a jumper wire between pins 1 amp 2 so that the unit can be used without a remote control connection If you will be using remote control you will first need to remove this jumper wire You can unplug the terminal block to make connections and after you have made the connections to the terminal block plug it back into the connector on the rear of the unit Never solder tin wires before inserting into a terminal block solder cold flows and you will eventually have loose connections The connections are shown below Pin 1 Contact Closure Pin 2 Contact Closure Applied Voltage Pin 3 Applied Voltage Pin 4 Remote LED Pin 5 Remote LED Pin 6 Aux Relay Contact Pin 7 Aux Relay Contact LIEIEETETETE 3 3 1 Control Inputs The Space Saver products can be controlled by a DC voltage in the range 5V to 30V by a contact closure such as a relay by a switch latching or by another SurgeX product such as the SEQ Switches with gold contacts are recommended for the best long term reliability a DC Voltage The unit will power up when the voltage is present and power down when there is no voltage Connect the positive wire to Pin 2 Applied2. SurgeX Space Saver Product Line Compact Mount CM Versatile Rear Mount VM USER MANUAL Space Saver Manual I DESCRIPTION isaisa AA AA AA AAA AAA IN FEATURES ip A S EM ortis au n PD M En RAE RU EUR AA aaea 3 INSTALLATION A A A EDD DARE CEN MIT KR MAGNI 3 1 PHYSICAL DIMENSI NS een eee eo eroe so eene e Vo eo eoe re sena ti Vo eonun o ee iuge se ve eoa o d e ou dn se v s anoo oe V gus Ue s nSo o s e s v EVE suve 32 120V CONNECTIONS 5 n eee nann A COE GUN CREE A Ee e EE EUN RE OUR LEG UUS CERO NA 3 3 REMOTE CONTROL CONNECTIONS eee ee ee eo ooo tn seen osten nest en aetate setae e ena seen e enne oe toas e ense seen e eaae seen 3 34 NA O aadi es aaasta A ME MPa Ed erue Me 3 3 2 EXTERNAL LED CONNECTIONS occccccconnnccinononecinononacinanonecnnanonacnnannnaconononaconannnannannn nes ease ds ease nds nne 3 3 8 AUXILIARY RELAY CONTACTS ii 4 LED INDICATORS conri ii AA M a lun SEECTETCATION Sii A AAA AAA AA AAA AAA AAA A AA SURGEN Space Saver Manual 1 Description The SurgeX Space Saver products are 120V 15 20 Amp AC power quality products incorporating SurgeX Advanced Series Mode power conditioning and surge protection The surge protection is rated A 1 1 the highest standard of the Federal Commercial Item Description for Endurance Several mounting options and receptacle configurations are available SurgeX ICE Inrush Current Elimination circuitry is incorporated into all
3. Voltage and the negative wire to Pin 3 Applied Voltage The positive and negative connections must be made with the correct polarity for proper operation b Contact Closure Latching Switch The unit will power up when the contacts are closed and power down when the contacts are open Connect the two wires from the contacts or switch to Pin 1 Contact Closure and Pin 2 Contact Closure Applied Voltage 3 3 2 External LED Connections The CM and VM Space Saver products are able to drive external LEDs or other signaling devices through their 12V DC output which can provide up to 10mA of current External LEDs connected in this way will be On when the unit s AC receptacles are On and Off when they are Off When connecting LEDs to the 12V output a series resistor is required For example many LEDs work well with 10mA of current so a 1KQ resistor is usually a good choice If more than one LED is required then use a separate series resistor for each LED For example two external LEDs each with a 2kQ series resistor could be powered from one unit at SmA each Connect each LED anode to Remote LED through a resistor and the cathodes to Remote LED SURGEN Space Saver Manual 3 3 3 Auxiliary Relay Contacts The auxiliary relay contacts Pins 6 amp 7 provide a way to cascade units or to provide confirmation feedback to a central controller When the switched receptacles are on the aux relay contacts are clo
4. ations Operational Voltage Range Current rating Power Rating Maximum Load Inrush Energy Under Voltage Shutdown Over Voltage Shutdown Surge Let through Voltage Meets Federal Guidelines EMI RFI Filter Normal Mode EMI RFI Filter Common Mode Maximum Applied Surge Voltage Maximum Applied Surge Current Maximum Applied Surge Energy Endurance Number of Outlets Remote Control Voltage Remote Control Current Draw Contact Closure Max Resistance Auxiliary Relay Contact Rating 12 Volt Output Max Current Dimensions no rack ears or feet Weight Temperature Range Humidity Range 90 to 150 Volts AC 15 20 Amps 1 800 2 400 Watts 1000 Joules total during power up 90 V resume at 100V 145V resume at 135V Zero let through Voltage for a 6000 Volt surge Grade A Class 1 Mode 1 CID A A 55818 40 dB 100 KHz 50dB 300 KHz 50 dB 3 MHz 50 dB 30 MHz 50 Ohm load 18dB 300 KHz 30 dB 1 MHz 50 dB 5 MHz 50 dB 20 MHz 50 Ohm load 6 000 Volts Unlimited due to current limiting Unlimited due to current limiting C62 41 1991 category B3 pulses 1 KV gt 500 000 3 KV gt 10 000 6 KV gt 1000 2 8 18 or 24 Model Dependent 5 to 30 Volts DC 4 mA maximum 100 Ohms 30 Volts DC at 1 Amp 20 mA Refer to Section 2 1 Physical Dimensions Refer to Section 2 1 Physical Dimensions 5C to 35C 596 to 9596 R H Non condensing Agency Listings ETL and
5. cETL UL 1449 Third Edition Type 3 Surge Protective Device UL 1283 CSA C22 2 No 8 M1986 R2004 Listed as base models SX 1115 RT SX 1120 RT 1 2 x 50 microsecond industry standard combination wave surge as per IEEE C62 41 CAUTION Do not repeatedly turn a unit off on off on with a heavy load connected The ICE circuitry absorbs the inrush energy each time the unit is turned on and may overheat if this is done too many times in a short period of time Wait one minute between repeated turn ons CAUTION Do not install this device if there is not at least 10 meters 30 feet or more between the electrical outlet and the electrical service panel
6. of the Space Saver products ICE eliminates problems associated with inrush currents from large loads such as amplifiers With SurgeX ICE it is not necessary to take inrush currents into account when designing the AC power for a system and special time delay circuit breakers are not required you only need to ensure that the steady state currents of all products plugged into the Compact Mount or Versatile Rear Mount product are within the 15 20 Amp rating The Space Saver products incorporate contact closure and applied DC voltage remote control capabilities Two or more CM or VM products can be connected together to provide control and power conditioning for larger systems They can also control other SurgeX products with their auxiliary relay contacts and or its 12V DC output A plug in Phoenix terminal block on the rear panel accommodates the remote control connections and also the low voltage outputs There are three inputs which control power state one 12V DC output and one auxiliary relay providing normally open contacts The inputs can be controlled by an applied DC voltage from 5V to 30V or by a contact closure The inputs and 12V DC output are designed to withstand incorrect connections including polarity reversal and shorts 2 Features e SurgeX Advanced Series Mode surge elimination SurgeX Impedance Tolerant EMI RFI filtering e SurgeX ICE Inrush Current Elimination e SurgeX CouVs Catastrophic Over Under Voltage Shu
7. sed There is a 1 second delay before the aux relay closes which allows time for the SurgeX Inrush Current Elimination ICE circuit to operate This short delay in combination with the SurgeX ICETM makes it unnecessary to sequence the power to several large loads such as amplifiers because of inrush current SurgeX Space Saver products when cascaded can turn on a bank of large amplifiers with no inrush current and therefore no risk of tripping a circuit breaker To cascade two or more Space Saver products connect the aux relay contacts of one unit to the contact closure input of the next unit To provide confirmation feedback connect the aux relay contacts to an input on the central controller The relay contacts are rated for 1 amp at 30 V DC 4 LED Indicators There are four LED indicators Self Test O Power located on the front panel Their function is as follows Over Under Voltage LO Remote Y Protection Self Test Green When illuminated the surge protection circuitry is functioning correctly Power Red When illuminated the power switch is turned on power is applied to the unit and the AC voltage is within normal limits Over Under Voltage When illuminated indicates that the AC voltage is either Protection Orange below 90V or above 145V Remote Yellow When illuminated indicates that the remote control is active and the rear switched receptacles are on SURGEN Space Saver Manual 5 Specific
8. tdown e Accepts both DC voltage and contact closure control inputs e Two or more units can be cascaded together for larger systems e Auxiliary relay output can be used to control other SurgeX products e 12 Volt dc output can be used to control other SurgeX products or drive LEDs e Auxiliary relay or 12 Volt dc output can be used to provide confirmation feedback e Flexible form factor o Compact Mount CM products have a standalone brick form factor with options for built in receptacles or an 18 or 24 outlet power strip o Versatile Rear Mount VM products have a IRU form factor designed to be vertically mounted to the rear of an equipment rack with hinged and fixed brackets SURGEN Space Saver Manual 3 Installation Compact Mount CM products are designed to rest on a flat surface or to be mounted onto a flat surface such as a wall To mount the CM product use six 6 32 Phillips pan head screws included to attach the removable mounting brackets included to the sides of the product The attached power strip available with CM 1115 20 RT18 and CM 1115 20 RT24 is designed to rest on a flat surface or to be mounted along the side of a standard eguipment rack Versatile Rear Mount VM products are designed to be mounted vertically either to a flat surface or spanning the rear of a standard eguipment rack Use eight 6 32 Phillips pan head screws included to attach the removable mounting brackets included
9. to the sides of the product It is recommended to attach the hinged mounting bracket to the side of the product closest to the input power cord 3 1 Physical Dimensions Base Unit Attached Power Strip Model Width Depth Height Weight Width Length Height Weight CM 1115 20 RT 4 95 9 50 5 66 8 5 Ib NA NA NA NA CM 1115 20 RT18 4 95 9 50 5 66 8 5 Ib 1 625 48 1 5 5 8 Ib CM 1115 20 RT24 4 95 9 50 5 66 8 5 Ib 1 625 62 L3 4 8 Ib VM 1115 20 RT 17 41 10 63 1 73 11 Ib NA NA NA NA Space Saver Manual SURGEN 3 2 120 Volt Connections Connect power to the unit by plugging the cord into a 120V AC 15 20 amp wall or floor receptacle Do not plug the unit into a re locatable power tap The various receptacle configurations are detailed in the following tables Each receptacle is rated for a maximum load of 15 Amps but the total load must not exceed 15 Amps 20 Amps for e GM IIls RT CM 1120 RT 20A products 7 CouVs P d 7 EMI RFI Filter t 15A 120V or 20A 20V Dutlets 2 Dutlets GM Iis RTI8 CM 1120 RTI6 GM Ill5 RT24 CM 1120 RT24 S 4 radi 2 a Pd A AE 154 20V or 204 120V 154 120V or 20A 120V 18 Dutlets 24 Dutlets ra i VM III5 RT CouVs A 7 EMI RFI Filter Pd mm Dutlets 8 Dutlets B switched 2 always on VM 1120 RT NNININ 204 120V 8 Outlets
Download Pdf Manuals
Related Search