ISO5500EVM User`s Manual (Rev. A)
Contents
1. 3 You will employ reasonable safeguards to ensure that your use of the EVM will not result in any property damage injury or death even if the EVM should fail to perform as described or expected 4 You will take care of proper disposal and recycling of the EVM s electronic components and packing materials Certain Instructions It is important to operate this EVM within TI s recommended specifications and environmental considerations per the user guidelines Exceeding the specified EVM ratings including but not limited to input and output voltage current power and environmental ranges may cause property damage personal injury or death If there are questions concerning these ratings please contact a TI field representative prior to connecting interface electronics including input power and intended loads Any loads applied outside of the specified output range may result in unintended and or inaccurate operation and or possible permanent damage to the EVM and or interface electronics Please consult the EVM User s Guide prior to connecting any load to the EVM output If there is uncertainty as to the load specification please contact a TI field representative During normal operation some circuit components may have case temperatures greater than 60 C as long as the input and output are maintained at a normal ambient operating temperature These components include but are not limited to linear regulators switching transistors pass transisto2. IC rules For EVMs not subject to the above rules this evaluation board kit module is intended for use for ENGINEERING DEVELOPMENT DEMONSTRATION OR EVALUATION PURPOSES ONLY and is not considered by TI to be a finished end product fit for general consumer use It generates uses and can radiate radio frequency energy and has not been tested for compliance with the limits of computing devices pursuant to part 15 of FCC or ICES 003 rules which are designed to provide reasonable protection against radio frequency interference Operation of the equipment may cause interference with radio communications in which case the user at his own expense will be required to take whatever measures may be required to correct this interference General Statement for EVMs including a radio User Power Frequency Use Obligations This radio is intended for development professional use only in legally allocated frequency and power limits Any use of radio frequencies and or power availability of this EVM and its development application s must comply with local laws governing radio spectrum allocation and power limits for this evaluation module It is the user s sole responsibility to only operate this radio in legally acceptable frequency space and within legally mandated power limitations Any exceptions to this are strictly prohibited and unauthorized by Texas Instruments unless user has obtained appropriate experimental development licenses from local regulatory auth
3. Should this evaluation board kit not meet the specifications indicated in the User s Guide the board kit may be returned within 30 days from the date of delivery for a full refund THE FOREGOING WARRANTY IS THE EXCLUSIVE WARRANTY MADE BY SELLER TO BUYER AND IS IN LIEU OF ALL OTHER WARRANTIES EXPRESSED IMPLIED OR STATUTORY INCLUDING ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE The user assumes all responsibility and liability for proper and safe handling of the goods Further the user indemnifies TI from all claims arising from the handling or use of the goods Due to the open construction of the product it is the user s responsibility to take any and all appropriate precautions with regard to electrostatic discharge EXCEPT TO THE EXTENT OF THE INDEMNITY SET FORTH ABOVE NEITHER PARTY SHALL BE LIABLE TO THE OTHER FOR ANY INDIRECT SPECIAL INCIDENTAL OR CONSEQUENTIAL DAMAGES Tl currently deals with a variety of customers for products and therefore our arrangement with the user is not exclusive Tl assumes no liability for applications assistance customer product design software performance or infringement of patents or services described herein Please read the User s Guide and specifically the Warnings and Restrictions notice in the User s Guide prior to handling the product This notice contains important safety information about temperatures and voltages For additional information on Tl s environment
4. operate the equipment FCC Interference Statement for Class A EVM devices NOTE This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense 3 2 3 3 FCC Interference Statement for Class B EVM devices NOTE This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning th
5. Board The ISO5500 is an isolated gate driver with several important features The printed circuit board PCB has been designed to support this device and to allow the user to evaluate its basic operation and features The left side of the PCB contains the interface to the input control and status functions of the integrated circuit IC The right side of the PCB has been designed to interface to an IGBT or MOSFET No electrical connections exist between the right and left sides of the PCB Refer to the ISO5500EVM schematic and bill of materials to become familiar with the PCB components and layout The PCB files Gerber ODB are available from Texas Instruments on request ISO5500 Operation Left Side Operation DC Power Control and Status 2 1 1 1 DC Power The left side of the ISO5500 and therefore the PCB can be operated using either a 3 8 V 10 or 5 V 10 dc power supply The small amount of dc current required lt 20 mA means that the device can also be battery operated The dc power supply must be connected to TP10 5 Vdc and TP9 5 Vdc return Also a user can solder wires directly to the PCB from the dc power supply by means of the plated through holes located next to the test points 2 1 1 2 Control and Status The interface to the device is via the JMP1 header It contains the VIN and VIN inputs the device RESET and FAULT indicator output The JMP1 header allows easy connections to test equipment using sta
6. C2 10 uF AVX TPSB106K020R1000 3 1 C3 1 uF AVX TPSA105K020R3000 4 1 C4 0 1 UF GARRETT X7RO805HTTD104K 5 2 C5 C13 0 01 uF KEMET C0805C103M5RACTU 6 1 C6 330 pF KEMET C0805C331J5GACTU 7 2 C7 C14 0 1 UF KEMET C0805C104K5RACTU 8 1 C8 100 pF KEMET C0805C101J5GACTU 9 1 C9 10nF KEMET C0805C103K1RAC3123 10 1 C10 10 uF TAIYO YUDEN UMK325BJ106MM T 11 1 C11 1 uF PANASONIC ECQ V1J105JM 12 1 C12 0 1 UF KEMET C0805C104M5RACTU 13 2 C15 C16 4 7 uF VISHAY SPRAGUE TR3D475K050C0300 14 1 C17 68 UF United Chemicon EMVY500ADA680MHZ0G 15 1 D1 UF4007 VISHAY UF4007 16 1 D2 DNI UF4007 16 AWG Wire Short 16 AWG Wire Short 17 1 D3 DNI UF4007 VISHAY UF4007 18 1 JMP1 HDR_THVT_2x4_100M Sullins S1032 04 ND 19 7 JMP2 JMP3 JMP4 JMP5 JMP6 JMP7 JMP8 HDR_THVT_1x2 Sullins S1032 02 ND 20 10 MFG1 MFG2 MFG3 MFG4 MFG5 MFG6 MFG9 MFG MFGO60_PTH Plated Through Holes 0 060 Holes for 10 MFG11 MFG12 Customer Use Only 21 2 P5 P6 Banana Jack ITT POMONA 3267 22 1 Q1 POWER FET DNI DNI 23 1 R1 3 3K VISHAY CRCW0805332FKEF 24 1 R2 0 Panasonic ERJ 6GEYOROOV 25 1 R3 100 Panasonic ERJ 6GEY101V 26 1 R4 10 Panasonic ERJ 1TYF100U 27 1 R5 DNI 10 Panasonic ERJ 1TYF100U 28 9 TP1 TP2 TP3 TP4 TP5 TP6 TP7 TP8 TP13 Test Loop Black Component Corporation TP 105 40 00 29 2 TP9 TP11 Test Loop Black KEYSTONE 5011 30 2 TP10 TP12 Test Loop RED KEYSTONE 5010 31 1 U1 ISO5500 Texas Instruments ISO5500 32 4 Bottom Side as shown on Bottom Side Silkscreen Bumpon Hemisphere Black 3M SJ 5003 33 5 To Be Install
7. TI does not offer any refunds returns or exchanges Furthermore no return of EVM s will be accepted if the package has been opened and no return of the EVM s will be accepted if they are damaged or otherwise not in a resalable condition If User feels it has been incorrectly charged for the EVM s it ordered or that delivery violates the applicable order User should contact TI All refunds will be made in full within thirty 30 working days from the return of the components s excluding any postage or packaging costs Governing Law These terms and conditions shall be governed by and interpreted in accordance with the laws of the State of Texas without reference to conflict of laws principles User agrees that non exclusive jurisdiction for any dispute arising out of or relating to these terms and conditions lies within courts located in the State of Texas and consents to venue in Dallas County Texas Notwithstanding the foregoing any judgment may be enforced in any United States or foreign court and TI may seek injunctive relief in any United States or foreign court Mailing Address Texas Instruments Post Office Box 655303 Dallas Texas 75265 Copyright 2015 Texas Instruments Incorporated IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries Tl reserve the right to make corrections enhancements improvements and other changes to its semiconductor products and services per JESD46 latest issue and to discontinue any
8. date of delivery for a full refund THE FOREGOING LIMITED WARRANTY IS THE EXCLUSIVE WARRANTY MADE BY SELLER TO BUYER AND IS IN LIEU OF ALL OTHER WARRANTIES EXPRESSED IMPLIED OR STATUTORY INCLUDING ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE EXCEPT TO THE EXTENT OF THE INDEMNITY SET FORTH ABOVE NEITHER PARTY SHALL BE LIABLE TO THE OTHER FOR ANY INDIRECT SPECIAL INCIDENTAL OR CONSEQUENTIAL DAMAGES Please read the User s Guide and specifically the Warnings and Restrictions notice in the User s Guide prior to handling the product This notice contains important safety information about temperatures and voltages For additional information on TI s environmental and or safety programs please visit www ti com esh or contact TI No license is granted under any patent right or other intellectual property right of TI covering or relating to any machine process or combination in which such TI products or services might be or are used TI currently deals with a variety of customers for products and therefore our arrangement with the user is not exclusive Tl assumes no liability for applications assistance customer product design software performance or infringement of patents or services described herein REGULATORY COMPLIANCE INFORMATION As noted in the EVM User s Guide and or EVM itself this EVM and or accompanying hardware may or may not be subject to the Federal Communications Commission FCC and Industry Canada
9. failures that might cause harm and take appropriate remedial actions Buyer will fully indemnify TI and its representatives against any damages arising out of the use of any TI components in safety critical applications In some cases TI components may be promoted specifically to facilitate safety related applications With such components Tl s goal is to help enable customers to design and create their own end product solutions that meet applicable functional safety standards and requirements Nonetheless such components are subject to these terms No Tl components are authorized for use in FDA Class III or similar life critical medical equipment unless authorized officers of the parties have executed a special agreement specifically governing such use Only those TI components which TI has specifically designated as military grade or enhanced plastic are designed and intended for use in military aerospace applications or environments Buyer acknowledges and agrees that any military or aerospace use of TI components which have not been so designated is solely at the Buyer s risk and that Buyer is solely responsible for compliance with all legal and regulatory requirements in connection with such use TI has specifically designated certain components as meeting ISO TS16949 requirements mainly for automotive use In any case of use of non designated products TI will not be responsible for any failure to meet ISO TS16949 Products Appli
10. or services or a warranty or endorsement thereof Use of such information may require a license from a third party under the patents or other intellectual property of the third party or a license from TI under the patents or other intellectual property of TI Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties conditions limitations and notices TI is not responsible or liable for such altered documentation Information of third parties may be subject to additional restrictions Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice TI is not responsible or liable for any such statements Buyer acknowledges and agrees that it is solely responsible for compliance with all legal regulatory and safety related requirements concerning its products and any use of TI components in its applications notwithstanding any applications related information or support that may be provided by TI Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which anticipate dangerous consequences of failures monitor failures and their consequences lessen the likelihood of
11. ss eee cease eeeneeeeeeeaeeeeeeeeeaseaeeeeeneeeeeenaeees 4 4 Component Changes to Change Turnon TUrnOff is sisssissessesseeseeeeeseessee 5 List of Tables 1 TOSt POMS ES ed a MN ana ee ensuite dedans en nes cents ane n ent 5 2 Blof Mate Ral S seen Retenir bas ame semence ne aman case De re Roca 6 1 Introduction 1 1 Overview This ISO5500EVM was designed to allow the user to evaluate the performance and features of the ISO5500 This includes the IGBT desaturation protection DESAT and the UVLO circuit that ensures a sufficient gate voltage is available to drive the IGBT or MOSFET The printed circuit board PCB also includes provisions to adjust the turnon turnoff characteristics by changing the loading between the ISO5500 output and the IGBT or MOSFET gate The EVM kit includes the ISO5500 data sheet Figure 1 shows the device pinout and the functional block diagram QuietZone is a trademark of 3M SLLU136A September 2011 Revised November 2012 ISO5500EVM 1 Submit Documentation Feedback Copyright 2011 2012 Texas Instruments Incorporated TA TEXAS INSTRUMENTS Printed Circuit Board www ti com 1 2 2 1 2 1 1 DEVICE PINOUT FUNCTION DIAGRAM Isolation Barrier Figure 1 1SO5500 Pinout and Functional Block Diagram ISO5500EVM Kit Contents ISO5500EVM printed circuit board with ISO5500DW installed P N 6512405 ISO5500EVM User s Guide This document IS05500 data sheet Printed Circuit
12. 5 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Reorient or relocate the receiving antenna e Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected e Consult the dealer or an experienced radio TV technician for help For EVMs annotated as IC INDUSTRY CANADA Compliant This Class A or B digital apparatus complies with Canadian ICES 003 Changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment Concerning EVMs including radio transmitters This device complies with Industry Canada licence exempt RSS standard s Operation is subject to the following two conditions 1 this device may not cause interference and 2 this device must acc
13. ENEER 3 OTY 4 JUMPER SHORTS WITH HANDLE TYCO P N 881545 2 TO BE Ba Devt ype Dis 200 INSTALLED ON JMP4 JMP7 LAYOUT DATE ISO5500 Eval Board 4 DURING EVM ASSEMBLY A 16 AWG GAUGE WIRE SHORT IS A Dalrymple lt Datel gt INSTALLED IN PLACE OF D2 RELEASED DATE Size Document Number Rev Sheet lt OrgAddr3 gt lt Date2 gt A 6512405 1 of 2 IS05500 Eval Board PAGE TITLE Evaluation Board Kit Important Notice Texas Instruments Tl provides the enclosed product s under the following conditions This evaluation board kit is intended for use for ENGINEERING DEVELOPMENT DEMONSTRATION OR EVALUATION PURPOSES ONLY and is not considered by TI to be a finished end product fit for general consumer use Persons handling the product s must have electronics training and observe good engineering practice standards As such the goods being provided are not intended to be complete in terms of required design marketing and or manufacturing related protective considerations including product safety and environmental measures typically found in end products that incorporate such semiconductor components or circuit boards This evaluation board kit does not fall within the scope of the European Union directives regarding electromagnetic compatibility restricted substances ROHS recycling WEEE FCC CE or UL and therefore may not meet the technical requirements of these directives or other related directives
14. IA TEXAS INSTRUMENTS User s Guide SLLU136A September 2011 Revised November 2012 ISOS500EVM This document describes the ISO5500 Evaluation Module EVM and allows designers to analyze and evaluate the Texas Instruments ISO5500 Isolated Gate Driver The ISO5500EVM can be used to evaluate device parameters while acting as a guide for board layout The board allows the user to evaluate device performance using a simulated 10 nF IGBT load installed on the board or to install an IGBT or MOSFET TO 247 package onto the board and drive it with the ISO5500 Contents 1 INTOAUCLION 2 52 una A A Uasss ler tele les 1 1 1 OVervieW sicarcaniticvesadwanevenwcaneninenduarevencneasecamanecanevemauianamameddvenexemasuabes aves ovawonemanexsernned 1 1 2 ISO5500EVM Kit Contents sassssssanassenesasnemmnaseeenanesenasenmescmennssenesanaeseneetiees 2 2 Printed GirCuit BOA 25cm smememanenenenenenmensnenenenenstenmammenensnesensm tesmenenenenssenneemaineensuene 2 2 1 ISO5500 Op ration secure EEE E aches aap camaewsmamemenuan EEO 2 2 2 schematic and Billtof Materials scie ssis soamesssessen cients suenesanessamnmisensenteseasnasencs nenteise 5 List of Figures 1 ISO5500 Pinout and Functional Block Diagram ssssssssrsrnssnsnnnnnnnnnnnnnnnnrrnrrrrrrrnnnnnnnnnnrnnnnnnnnn 2 2 High Side Interconnection Diagram aasassssssssssnnnnnnnnnrnnnnnnnnnnnrnnnnnsnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnn 4 3 Low Side Interconnection Diagram
15. If the user wishes to install a different device onto the PCB and that device does not use pin 15 as a VEE connection the user can simply use the jumper short from JMP8 This opens the pin 15 connection to VEE JMP8 can then be used as a test point for the output signal on pin 15 2 1 3 Test Points Test points have been provided for ready access to signal monitoring They are listed in Table 1 Table 1 Test Points TEST POINT VO FUNCTION TP1 Output FAULT PIN Left side TP2 Input RESET Left side TP3 Input VIN Left side TP4 Input VIN Left side TP5 Output VOUT Right Side TP6 Output GATE VOLTAGE Right Side TP7 Input DRAIN VOLTAGE Right Side TP8 Input DESAT VOLTAGE Right Side TP9 Output GND1 Left side TP10 Input VCC1 Left side TP11 Output VEE Right Side TP12 Input VCC2 Right Side TP13 Input VE Right Side 2 2 Schematic and Bill of Materials The ISO5500EVM schematic follows the bill of materials SLLU136A September 2011 Revised November 2012 ISO5500EVM 5 Submit Documentation Feedback Copyright 2011 2012 Texas Instruments Incorporated Printed Circuit Board Table 2 Bill of Materials I TEXAS INSTRUMENTS www ti com Item Qty Reference Value Manufacturer Manufacturer Part No 1 1 C1 68 UF AVX TPSE686K020R0150 2 1
16. LAW OF TORT CONTRACT OR ANY OTHER LEGAL THEORY AND EVEN IF THE EVM FAILS TO PERFORM AS DESCRIBED OR EXPECTED Limitations on Damages and Liability 8 1 General Limitations IN NO EVENT SHALL TI BE LIABLE FOR ANY SPECIAL COLLATERAL INDIRECT PUNITIVE INCIDENTAL CONSEQUENTIAL OR EXEMPLARY DAMAGES IN CONNECTION WITH OR ARISING OUT OF THESE TERMS ANDCONDITIONS OR THE USE OF THE EVMS PROVIDED HEREUNDER REGARDLESS OF WHETHER TI HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES EXCLUDED DAMAGES INCLUDE BUT ARE NOT LIMITED TO COST OF REMOVAL OR REINSTALLATION ANCILLARY COSTS TO THE PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES RETESTING OUTSIDE COMPUTER TIME LABOR COSTS LOSS OF GOODWILL LOSS OF PROFITS LOSS OF SAVINGS LOSS OF USE LOSS OF DATA OR BUSINESS INTERRUPTION NO CLAIM SUIT OR ACTION SHALL BE BROUGHT AGAINST TI MORE THAN ONE YEAR AFTER THE RELATED CAUSE OF ACTION HAS OCCURRED 8 2 Specific Limitations INNO EVENT SHALL TI S AGGREGATE LIABILITY FROM ANY WARRANTY OR OTHER OBLIGATION ARISING OUT OF OR IN CONNECTION WITH THESE TERMS AND CONDITIONS OR ANY USE OF ANY TI EVM PROVIDED HEREUNDER EXCEED THE TOTAL AMOUNT PAID TO TI FOR THE PARTICULAR UNITS SOLD UNDER THESE TERMS AND CONDITIONS WITH RESPECT TO WHICH LOSSES OR DAMAGES ARE CLAIMED THE EXISTENCE OF MORE THAN ONE CLAIM AGAINST THE PARTICULAR UNITS SOLD TO USER UNDER THESE TERMS AND CONDITIONS SHALL NOT ENLARGE OR EXTEND THIS LIMIT Return Policy Except as otherwise provided
17. RN HV Banana Jack CONNECTED TO P5 OR MFG1 LOAD D G MEG2 MEG4 gt HV CONNECTED TO MFG6 P6 Banana Jack Figure 3 Low Side Interconnection Diagram 2 1 2 4 Turnon Turnoff Adjust The PCB contains a single 10 Q gate resistor R4 and a short bus wire in place of diode D2 This simple configuration sets the peak current at approximately 3 A with turnon turnoff characteristics the same The PCB has provisions for the user to install the D2 and D3 diodes and R4 and R5 resistors This allows the user to evaluate device operation with different on off characteristics This is shown in Figure 4 The turnon characteristics can also be adjusted with the value of R2 which connects VC to VCC2 As shipped R2 is set to 0 Q but the user can change this and examine the effects on turnon characteristics 4 ISO5500EVM SLLU136A September 2011 Revised November 2012 Submit Documentation Feedback Copyright 2011 2012 Texas Instruments Incorporated 1 TEXAS INSTRUMENTS www ti com Printed Circuit Board Turnon Turnoff The R4 D2 As Shipped Same D3 RS o o To Change Turnon and R4 D2 Turnoff D3 R5 Wp Figure 4 Component Changes to Change Turnon Turnoff 2 1 2 5 The Interchange Jumper JMP8 The ISO5500 device is similar to other devices currently available from other manufacturers One of the similar devices uses pin 15 as an output driver for an LED The TI ISO5500 uses pin 15 as a VEE GND connection
18. TO 247 package The PCB has provisions to solder an IGBT directly onto the board 2 1 2 3 1 No IGBT or MOSFET Installed JMP3 When using the simulated load the user must install a jumper short onto JMP3 This connects a 10 nF capacitor C9 to the Vout pin The simulated IGBT consists of the 10 Q gate resistor R4 and this 10 nF capacitor C9 2 1 2 3 2 IGBT or MOSFET Installed REMOVE JMP3 If the user chooses to install an IGBT JMP must be left open with no shorting jumper installed The PCB has been designed with several large plated through holes or vias to support both high side and low side drive configurations Note Plated through holes are designated as MFGx on the schematic The connections for these modes are described next 2 1 2 3 3 High Side Low Side Operation and Interconnection The connections required for high side and low side operation are shown in Figure 2 and Figure 3 respectively The user can select the load and install it directly on the PCB SLLU136A September 201 1 Revised November 2012 ISO5500EVM 3 Submit Documentation Feedback Copyright 2011 2012 Texas Instruments Incorporated I TEXAS INSTRUMENTS Printed Circuit Board www ti com SCHEMATIC PCB CONNECTIONS HV P5 Banana Jack HV RETURN CONNECTED TO MFG5 D G S LOAD P6 Banana Jack Figure 2 High Side Interconnection Diagram SCHEMATIC PCB CONNECTIONS P5 HV RETU
19. Unless otherwise indicated this EVM is not a finished electrical equipment and not intended for consumer use It is intended solely for use for preliminary feasibility evaluation in laboratory development environments by technically qualified electronics experts who are familiar with the dangers and application risks associated with handling electrical mechanical components systems and subsystems It should not be used as all or part of a finished end product Your Sole Responsibility and Risk You acknowledge represent and agree that 1 You have unique knowledge concerning Federal State and local regulatory requirements including but not limited to Food and Drug Administration regulations if applicable which relate to your products and which relate to your use and or that of your employees affiliates contractors or designees of the EVM for evaluation testing and other purposes 2 You have full and exclusive responsibility to assure the safety and compliance of your products with all such laws and other applicable regulatory requirements and also to assure the safety of any activities to be conducted by you and or your employees affiliates contractors or designees using the EVM Further you are responsible to assure that any interfaces electronic and or mechanical between the EVM and any human body are designed with suitable isolation and means to safely limit accessible leakage currents to minimize the risk of electrical shock hazard
20. al and or safety programs please contact the TI application engineer or visit www ti com esh No license is granted under any patent right or other intellectual property right of TI covering or relating to any machine process or combination in which such TI products or services might be or are used FCC Warning This evaluation board kit is intended for use for ENGINEERING DEVELOPMENT DEMONSTRATION OR EVALUATION PURPOSES ONLY and is not considered by TI to be a finished end product fit for general consumer use It generates uses and can radiate radio frequency energy and has not been tested for compliance with the limits of computing devices pursuant to part 15 of FCC rules which are designed to provide reasonable protection against radio frequency interference Operation of this equipment in other environments may cause interference with radio communications in which case the user at his own expense will be required to take whatever measures may be required to correct this interference EVM Warnings and Restrictions It is important to operate this EVM within the input voltage range of 3 3 V to 5 V and the output voltage range of 10 V to 30 V Exceeding the specified input range may cause unexpected operation and or irreversible damage to the EVM If there are questions concerning the input range please contact a TI field representative prior to connecting the input power Applying loads outside of the specified output range may result in
21. cations Audio www ti com audio Automotive and Transportation www ti com automotive Amplifiers amplifier ti com Communications and Telecom www ti com communications Data Converters DLP Products DSP Clocks and Timers Interface Logic Power Mgmt Microcontrollers RFID OMAP Applications Processors Wireless Connectivity dataconverter ti com www dip com www ti com clocks interface ti com logic ti com microcontroller ti com www ti rfid com www ti com omap Computers and Peripherals Consumer Electronics Energy and Lighting Industrial Medical Security Space Avionics and Defense Video and Imaging TI E2E Community www ti com wirelessconnectivity www ti com computers www ti com consumer apps www ti com energy www ti com industrial www ti com medical www ti com security www ti com space avionics defense www ti com video Mailing Address Texas Instruments Post Office Box 655303 Dallas Texas 75265 Copyright 2015 Texas Instruments Incorporated
22. ciated with handling electrical mechanical components systems and subsystems User assumes all responsibility and liability for proper and safe handling and use of the EVM by User or its employees affiliates contractors or designees User assumes all responsibility and liability to ensure that any interfaces electronic and or mechanical between the EVM and any human body are designed with suitable isolation and means to safely limit accessible leakage currents to minimize the risk of electrical shock hazard User assumes all responsibility and liability for any improper or unsafe handling or use of the EVM by User or its employees affiliates contractors or designees 4 4 User assumes all responsibility and liability to determine whether the EVM is subject to any applicable international federal state or local laws and regulations related to User s handling and use of the EVM and if applicable User assumes all responsibility and liability for compliance in all respects with such laws and regulations User assumes all responsibility and liability for proper disposal and recycling of the EVM consistent with all applicable international federal state and local requirements 5 Accuracy of Information To the extent TI provides information on the availability and function of EVMs TI attempts to be as accurate as possible However TI does not warrant the accuracy of EVM descriptions EVM availability or other information on its websites as accu
23. day warranty period Regulatory Notices 3 1 United States 8 1 1 Notice applicable to EVMs not FCC Approved This kit is designed to allow product developers to evaluate electronic components circuitry or software associated with the kit to determine whether to incorporate such items in a finished product and software developers to write software applications for use with the end product This kit is not a finished product and when assembled may not be resold or otherwise marketed unless all required FCC equipment authorizations are first obtained Operation is subject to the condition that this product not cause harmful interference to licensed radio stations and that this product accept harmful interference Unless the assembled kit is designed to operate under part 15 part 18 or part 95 of this chapter the operator of the kit must operate under the authority of an FCC license holder or must secure an experimental authorization under part 5 of this chapter 3 1 2 For EVMs annotated as FCC FEDERAL COMMUNICATIONS COMMISSION Part 15 Compliant CAUTION This device complies with part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation Changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to
24. e equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help Canada 3 2 1 For EVMs issued with an Industry Canada Certificate of Conformance to RSS 210 Concerning EVMs Including Radio Transmitters This device complies with Industry Canada license exempt RSS standard s Operation is subject to the following two conditions 1 this device may not cause interference and 2 this device must accept any interference including interference that may cause undesired operation of the device Concernant les EVMs avec appareils radio Le pr sent appareil est conforme aux CNR d Industrie Canada applicables aux appareils radio exempts de licence L exploitation est autoris e aux deux conditions suivantes 1 l appareil ne doit pas produire de brouillage et 2 l utilisateur de l appareil doit accepter tout brouillage radio lectrique subi m me si le brouillage est susceptible d en compromettre le fonctionnement Concerning EVMs Including Detachable Antennas Under Industry Canada regulations this radio transmitter may only operate using an antenna of a type and maximum or lesser gain approved for th
25. e transmitter by Industry Canada To reduce potential radio interference to other users the antenna type and its gain should be so chosen that the equivalent isotropically radiated power e i r p is not more than that necessary for successful communication This radio transmitter has been approved by Industry Canada to operate with the antenna types listed in the user guide with the maximum permissible gain and required antenna impedance for each antenna type indicated Antenna types not included in this list having a gain greater than the maximum gain indicated for that type are strictly prohibited for use with this device Concernant les EVMs avec antennes d tachables Conform ment la r glementation d Industrie Canada le pr sent metteur radio peut fonctionner avec une antenne d un type et d un gain maximal ou inf rieur approuv pour l metteur par Industrie Canada Dans le but de r duire les risques de brouillage radio lectrique l intention des autres utilisateurs il faut choisir le type d antenne et son gain de sorte que la puissance isotrope rayonn e quivalente p i r e ne d passe pas l intensit n cessaire l tablissement d une communication satisfaisante Le pr sent metteur radio a t approuv par Industrie Canada pour fonctionner avec les types d antenne num r s dans le manuel d usage et ayant un gain admissible maximal et l imp dance requise pour chaque type d antenne Les types d antenne non inclus dan
26. ed on JMP4 JMP7 Jumper Shorts With Handle TYCO 2 881545 2 6 ISO5500EVM SLLU136A September 2011 Revised November 2012 Copyright 2011 2012 Texas Instruments Incorporated Submit Documentation Feedback 1 TEXAS INSTRUMENTS www ti com Printed Circuit Board Table 2 Bill of Materials continued Item Qty Reference Value Manufacturer Manufacturer Part No NOTE ASSEMBLY INSTRUCTIONS BELOW INSTALL JUMPER SHORTS ITEM 33 ONTO THE FOLLOWING JUMPER LOCATIONS JMP1 3 TO JMP1 4 JMP1 5 TO JMP1 6 JMP2 JMP8 JMP9 INSTALL 16AWG WIRE IN PLACE OF D2 SLLU136A September 2011 Revised November 2012 ISO5500EVM 7 Submit Documentation Feedback Copyright 2011 2012 Texas Instruments Incorporated SHUNT PARKING LOT JMP4 JMP5 JMP6 JMP7 TESTLOOP RED HDR_THVT_1x2 10uF TP11 TESTLOOP BLACK P5 HDR_THVT_2x4_100M Banana Jack MFG5 GND1 JMP2 HDR_THVT_1x2 MeGt IMEG3 TP10 MFG10 D1 i SOURCE e cine DRAIN a MFG4 TESTLOOP RED C1 C2 VIN C4 de 14 UF4007 GATE GND1 MFG6 TP9 68uF 10uF 0 1uF 0 01UF RESET DNI UF4007 POWER FET FAULT ai NC TESTLOOP BLACK MFG9 GND1 P6 Banana Jack H IS05500 e HDR_THVT_1x2 DNI UF4007 DNI 10 C9 8 10n JMP8 HDR_THVT_1x2 TEXAS INSTRUMENTS NOTES 1 Q1 POWER FET IS POPULATED BY EVM CUSTOMER ONLY Srp saa bet ene 2 SHORTING JUMPER 3 MUST BE REMOVED IF USER INSTALLS FET ONTO THE EVM BOARD BNG
27. ept any interference including interference that may cause undesired operation of the device Concerning EVMs including detachable antennas Under Industry Canada regulations this radio transmitter may only operate using an antenna of a type and maximum or lesser gain approved for the transmitter by Industry Canada To reduce potential radio interference to other users the antenna type and its gain should be so chosen that the equivalent isotropically radiated power e i r p is not more than that necessary for successful communication This radio transmitter has been approved by Industry Canada to operate with the antenna types listed in the user guide with the maximum permissible gain and required antenna impedance for each antenna type indicated Antenna types not included in this list having a gain greater than the maximum gain indicated for that type are strictly prohibited for use with this device Cet appareil num rique de la classe A ou B est conforme a la norme NMB 003 du Canada Les changements ou les modifications pas express ment approuv s par la partie responsable de la conformit ont pu vider l autorit de l utilisateur pour actionner l quipement Concernant les EVMs avec appareils radio Le pr sent appareil est conforme aux CNR d Industrie Canada applicables aux appareils radio exempts de licence L exploitation est autoris e aux deux conditions suivantes 1 l appareil ne doit pas produire de brouillage et 2 l ut
28. est facility as defined in the notification 173 issued by Ministry of Internal Affairs and Communications on March 28 2006 based on Sub section 1 1 of Article 6 of the Ministry s Rule for Enforcement of Radio Law of Japan 2 Use this product only after you obtained the license of Test Radio Station as provided in Radio Law of Japan with respect to this product or 3 Use of this product only after you obtained the Technical Regulations Conformity Certification as provided in Radio Law of Japan with respect to this product Also please do not transfer this product unless you give the same notice above to the transferee Please note that if you could not follow the instructions above you will be subject to penalties of Radio Law of Japan Texas Instruments Japan Limited address 24 1 Nishi Shinjuku 6 chome Shinjuku ku Tokyo Japan http www tij co jp ZEATE T FAREY HSGRMBSBSTReLTTHVEtA ARMOCPAICRL TSH BREBTOL HO AFOUFNA NEER TULE lt KBEMHW ETN CCHRB lt K EEU 1 BRAT A ROR ARS CET lt FR18F3 AO AMBER A1735 CEOSHLEREESO MBM CEAR 2 RRRAO TFEMSRCHAUEEX 3 RN R RIENREMS RCHARUEEX ZB Ami Lito TEAC TORA REX BEAIBALZURY BE B T SUEDELRT Re FEU e USER BRAM RAAB AS Na NEEND eE TAERE BATEYA FYAYIDXYYRASE Raw ie XM 6 TA 24815 ME HEIL http www tij co jp EVALUATION BOARD KIT MODULE EVM WARNINGS RESTRICTIONS AND DISCLAIMERS For Feasibility Evaluation Only in Laboratory Development Environments
29. ffice Box 655303 Dallas Texas 75265 Copyright 2012 Texas Instruments Incorporated STANDARD TERMS AND CONDITIONS FOR EVALUATION MODULES Delivery TI delivers TI evaluation boards kits or modules including any accompanying demonstration software components or documentation collectively an EVM or EVMs to the User User in accordance with the terms and conditions set forth herein Acceptance of the EVM is expressly subject to the following terms and conditions 1 1 EVMs are intended solely for product or software developers for use in a research and development setting to facilitate feasibility evaluation experimentation or scientific analysis of Tl semiconductors products EVMs have no direct function and are not finished products EVMs shall not be directly or indirectly assembled as a part or subassembly in any finished product For clarification any software or software tools provided with the EVM Software shall not be subject to the terms and conditions set forth herein but rather shall be subject to the applicable terms and conditions that accompany such Software 1 2 EVMs are not intended for consumer or household use EVMs may not be sold sublicensed leased rented loaned assigned or otherwise distributed for commercial purposes by Users in whole or in part or used in any finished product or production system Limited Warranty and Related Remedies Disclaimers 2 1 These terms and conditions do no
30. ilisateur de l appareil doit accepter tout brouillage radio lectrique subi m me si le brouillage est susceptible d en compromettre le fonctionnement Concernant les EVMs avec antennes d tachables Conform ment la r glementation d Industrie Canada le pr sent metteur radio peut fonctionner avec une antenne d un type et d un gain maximal ou inf rieur approuv pour l metteur par Industrie Canada Dans le but de r duire les risques de brouillage radio lectrique l intention des autres utilisateurs il faut choisir le type d antenne et son gain de sorte que la puissance isotrope rayonn e quivalente p i r e ne d passe pas l intensit n cessaire l tablissement d une communication satisfaisante Le pr sent metteur radio a t approuv par Industrie Canada pour fonctionner avec les types d antenne num r s dans le manuel d usage et ayant un gain admissible maximal et l imp dance requise pour chaque type d antenne Les types d antenne non inclus dans cette liste ou dont le gain est sup rieur au gain maximal indiqu sont strictement interdits pour l exploitation de l metteur Important Notice for Users of this Product in Japan This development kit is NOT certified as Confirming to Technical Regulations of Radio Law of Japan If you use this product in Japan you are required by Radio Law of Japan to follow the instructions below with respect to this product 1 Use this product in a shielded room or any other t
31. ndard clip leads or QuietZone connectors Each of the four signals also has a test point for additional connections These are TP1 through TP4 ISO5500EVM SLLU136A September 2011 Revised November 2012 Submit Documentation Feedback Copyright 2011 2012 Texas Instruments Incorporated 1 TEXAS INSTRUMENTS www ti com Printed Circuit Board 2 1 2 Right Side Operation 2 1 2 1 DC Power Power is provided to Vcc2 on the right side of the device at TP12 Vdc and TP11 Vdc The dc supply must be able to provide a bias voltage over the range of 15 Vdc to 30 Vdc As the current requirement is extremely low the user may choose to operate the IS05500 by battery Solder holes are provided next to the test points if the user chooses to hardwire these connections If a negative gate drive is required a dc supply or battery must be connected across VE P5 or MFG1 to VEE MGF11 or TP11 The voltage range must be between 0 V and 15 Vdc 2 1 2 2 DESAT JMP2 One of the features of the ISO5500 is the IGBT desaturation protection JMP2 provides access to the DESAT pin It is a 2 pin male header and installing a shorting jumper onto JMP2 disables the DESAT function 2 1 2 3 IGBT or MOSFET As shipped the ISO5500EVM does not have an IGBT installed The user can evaluate device operation using a simulated IGBT load or they can remove the simulated load and install an IGBT onto the board Most IGBTs are available in the standard
32. o penalties of Radio Law of Japan RRER AES ORMORKRTY LESREVCSOROERSE BHT Y RORC M E RIERE ENT UVEWVEOPHWET KABA SH CUSVEOOCPAIRL TH BRABTOLO ALFOUTHAD PEER TWEE BEPHWETNCCER lt K EE 1 m Se PS ne ne D en 2 RRAD FEMSRCHAUEEX 3 RT RIEREMSRCH RUEEX ZA Fm Lo TEACO TOE CRE BRALBALZURY RE BETESUEDELKT RTA TEUSUES R BRAN RAIMBAE NSRP HOCCeCHB lt KEEW ARTETA 4 YAYINLA YARNS Raw ie Raa 6 TA 24815 Baa FEIL 3 3 3 Notice for EVMs for Power Line Communication Please see http www tij co jp Isds ti_ja general eStore notice_02 page SRA BIO COMBA Y LEB EUICSSRORBSRICIUTHH RNECZECKE lt KEKEE Uo http www tij co jp Isds ti_ja general eStore notice_02 page 4 EVM Use Restrictions and Warnings 4 1 EVMS ARE NOT FOR USE IN FUNCTIONAL SAFETY AND OR SAFETY CRITICAL EVALUATIONS INCLUDING BUT NOT LIMITED TO EVALUATIONS OF LIFE SUPPORT APPLICATIONS 4 2 User must read and apply the user guide and other available documentation provided by TI regarding the EVM prior to handling or using the EVM including without limitation any warning or restriction notices The notices contain important safety information related to for example temperatures and voltages 4 3 Safety Related Warnings and Restrictions 4 3 1 User shall operate the EVM within Tl s recommended specifications and environmental considerations stated in the user guide other available documentation provided by TI and any other applicable req
33. orities which is responsibility of user including its acceptable authorization For EVMs annotated as FCC FEDERAL COMMUNICATIONS COMMISSION Part 15 Compliant Caution This device complies with part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation Changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment FCC Interference Statement for Class A EVM devices This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense FCC Interference Statement for Class B EVM devices This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 1
34. product or service per JESD48 latest issue Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete All semiconductor products also referred to herein as components are sold subject to Tl s terms and conditions of sale supplied at the time of order acknowledgment TI warrants performance of its components to the specifications applicable at the time of sale in accordance with the warranty in Tl s terms and conditions of sale of semiconductor products Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty Except where mandated by applicable law testing of all parameters of each component is not necessarily performed Tl assumes no liability for applications assistance or the design of Buyers products Buyers are responsible for their products and applications using TI components To minimize the risks associated with Buyers products and applications Buyers should provide adequate design and operating safeguards TI does not warrant or represent that any license either express or implied is granted under any patent right copyright mask work right or other intellectual property right relating to any combination machine or process in which TI components or services are used Information published by TI regarding third party products or services does not constitute a license to use such products
35. rate complete reliable current or error free 10 Disclaimers 6 1 EXCEPT AS SET FORTH ABOVE EVMS AND ANY WRITTEN DESIGN MATERIALS PROVIDED WITH THE EVM AND THE DESIGN OF THE EVM ITSELF ARE PROVIDED AS IS AND WITH ALL FAULTS TI DISCLAIMS ALL OTHER WARRANTIES EXPRESS OR IMPLIED REGARDING SUCH ITEMS INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR NON INFRINGEMENT OF ANY THIRD PARTY PATENTS COPYRIGHTS TRADE SECRETS OR OTHER INTELLECTUAL PROPERTY RIGHTS 6 2 EXCEPT FOR THE LIMITED RIGHT TO USE THE EVM SET FORTH HEREIN NOTHING IN THESE TERMS AND CONDITIONS SHALL BE CONSTRUED AS GRANTING OR CONFERRING ANY RIGHTS BY LICENSE PATENT OR ANY OTHER INDUSTRIAL OR INTELLECTUAL PROPERTY RIGHT OF TI ITS SUPPLIERS LICENSORS OR ANY OTHER THIRD PARTY TO USE THE EVM IN ANY FINISHED END USER OR READY TO USE FINAL PRODUCT OR FOR ANY INVENTION DISCOVERY OR IMPROVEMENT MADE CONCEIVED OR ACQUIRED PRIOR TO OR AFTER DELIVERY OF THE EVM USER S INDEMNITY OBLIGATIONS AND REPRESENTATIONS USER WILL DEFEND INDEMNIFY AND HOLD TI ITS LICENSORS AND THEIR REPRESENTATIVES HARMLESS FROM AND AGAINST ANY AND ALL CLAIMS DAMAGES LOSSES EXPENSES COSTS AND LIABILITIES COLLECTIVELY CLAIMS ARISING OUT OF OR IN CONNECTION WITH ANY HANDLING OR USE OF THE EVM THAT IS NOT IN ACCORDANCE WITH THESE TERMS AND CONDITIONS THIS OBLIGATION SHALL APPLY WHETHER CLAIMS ARISE UNDER STATUTE REGULATION OR THE
36. rs and current sense resistors which can be identified using the EVM schematic located in the EVM User s Guide When placing measurement probes near these devices during normal operation please be aware that these devices may be very warm to the touch As with all electronic evaluation tools only qualified personnel knowledgeable in electronic measurement and diagnostics normally found in development environments should use these EVMs Agreement to Defend Indemnify and Hold Harmless You agree to defend indemnify and hold TI its licensors and their representatives harmless from and against any and all claims damages losses expenses costs and liabilities collectively Claims arising out of or in connection with any use of the EVM that is not in accordance with the terms of the agreement This obligation shall apply whether Claims arise under law of tort or contract or any other legal theory and even if the EVM fails to perform as described or expected Safety Critical or Life Critical Applications If you intend to evaluate the components for possible use in safety critical applications such as life support where a failure of the TI product would reasonably be expected to cause severe personal injury or death such as devices which are classified as FDA Class III or similar classification then you must specifically notify TI of such intent and enter into a separate Assurance and Indemnity Agreement Mailing Address Texas Instruments Post O
37. s cette liste ou dont le gain est sup rieur au gain maximal indiqu sont strictement interdits pour l exploitation de l metteur Japan 3 3 1 Notice for EVMs delivered in Japan Please see http www ti co jp Isds ti ja general eStore notice_01 page HABA Ic HAE NE EPA h R RICOIWUTE ROECSZECHRKEEW http www tij co jp Isds ti_ja general eStore notice_01 page 3 3 2 Notice for Users of EVMs Considered Radio Frequency Products in Japan EVMs entering Japan may not be certified by TI as conforming to Technical Regulations of Radio Law of Japan If User uses EVMs in Japan not certified to Technical Regulations of Radio Law of Japan User is required by Radio Law of Japan to follow the instructions below with respect to EVMs 1 Use EVMs in a shielded room or any other test facility as defined in the notification 173 issued by Ministry of Internal Affairs and Communications on March 28 2006 based on Sub section 1 1 of Article 6 of the Ministry s Rule for Enforcement of Radio Law of Japan 2 Use EVMs only after User obtains the license of Test Radio Station as provided in Radio Law of Japan with respect to EVMs or 3 Use of EVMs only after User obtains the Technical Regulations Conformity Certification as provided in Radio Law of Japan with respect to EVMs Also do not transfer EVMs unless User gives the same notice above to the transferee Please note that if User does not follow the instructions above User will be subject t
38. t apply to Software The warranty if any for Software is covered in the applicable Software License Agreement 2 2 Tl warrants that the TI EVM will conform to TI s published specifications for ninety 90 days after the date TI delivers such EVM to User Notwithstanding the foregoing TI shall not be liable for any defects that are caused by neglect misuse or mistreatment by an entity other than TI including improper installation or testing or for any EVMs that have been altered or modified in any way by an entity other than TI Moreover TI shall not be liable for any defects that result from User s design specifications or instructions for such EVMs Testing and other quality control techniques are used to the extent TI deems necessary or as mandated by government requirements TI does not test all parameters of each EVM 2 3 If any EVM fails to conform to the warranty set forth above TI s sole liability shall be at its option to repair or replace such EVM or credit User s account for such EVM TI s liability under this warranty shall be limited to EVMs that are returned during the warranty period to the address designated by TI and that are determined by TI not to conform to such warranty If TI elects to repair or replace such EVM TI shall have a reasonable time to repair such EVM or provide replacements Repaired EVMs shall be warranted for the remainder of the original warranty period Replaced EVMs shall be warranted for a new full ninety 90
39. uirements and employ reasonable and customary safeguards Exceeding the specified performance ratings and specifications including but not limited to input and output voltage current power and environmental ranges for the EVM may cause personal injury or death or property damage If there are questions concerning performance ratings and specifications User should contact a TI field representative prior to connecting interface electronics including input power and intended loads Any loads applied outside of the specified output range may also result in unintended and or inaccurate operation and or possible permanent damage to the EVM and or interface electronics Please consult the EVM user guide prior to connecting any load to the EVM output If there is uncertainty as to the load specification please contact a TI field representative During normal operation even with the inputs and outputs kept within the specified allowable ranges some circuit components may have elevated case temperatures These components include but are not limited to linear regulators switching transistors pass transistors current sense resistors and heat sinks which can be identified using the information in the associated documentation When working with the EVM please be aware that the EVM may become very warm 4 3 2 EVMs are intended solely for use by technically qualified professional electronics experts who are familiar with the dangers and application risks asso
40. unintended operation and or possible permanent damage to the EVM Please consult the EVM User s Guide prior to connecting any load to the EVM output If there is uncertainty as to the load specification please contact a TI field representative During normal operation some circuit components may have case temperatures greater than 80 C The EVM is designed to operate properly with certain components above 80 C as long as the input and output ranges are maintained These components include but are not limited to linear regulators switching transistors pass transistors and current sense resistors These types of devices can be identified using the EVM schematic located in the EVM User s Guide When placing measurement probes near these devices during operation please be aware that these devices may be very warm to the touch Mailing Address Texas Instruments Post Office Box 655303 Dallas Texas 75265 Copyright 2011 Texas Instruments Incorporated EVALUATION BOARD KIT MODULE EVM ADDITIONAL TERMS Texas Instruments Tl provides the enclosed Evaluation Board Kit Module EVM under the following conditions The user assumes all responsibility and liability for proper and safe handling of the goods Further the user indemnifies TI from all claims arising from the handling or use of the goods Should this evaluation board kit not meet the specifications indicated in the User s Guide the board kit may be returned within 30 days from the
Download Pdf Manuals
Related Search