Pelco DF5 Series Fixed Mount Dome_manual
Contents
1. 20035 20034 BACK BOX INSTALLATION PENDANT MODELS PENDANT MOUNT o INSTALL MOUNT Install the mount for the pendant dome Refer to the instructions supplied with the mount If you are installing the dome outdoors make sure the mount is properly sealed to keep moisture from damaging Y the structure to which it is attached 20041 PREPARE WIRING Bring a coaxial cable for the camera through the mount Also bring wiring for power through the mount Refer to Tables A and B in the Appendix for wiring distances INSTALL THE BACK BOX Pull wiring from the mount into the back box Apply thread compound anti seize lubricant to the threads on the back box If you are installing the dome outdoors seal the inside of the pipe portion of the back box to prevent moisture or cold air inside of the mount from entering the unit and causing condensation on the dome Use a product such as Duct Seal or a foam insulation spray that is available from an electrical supply house Screw the back box into the mount Pelco Manual C1458M G 5 05 BACK BOX INSTALLATION PENDANT MODELS SURFACE MOUNT Pelco Manual C1458M G 5 05 1 REMOVE THE TOP MOUNT FROM THE BACK BOX If you have an outdoor model remove the sun shield Take out the black tilt table assembly inside of the back box by removing the nuts and washers that hold the three legs to the back box Take off the top mount by removing the three screws and lock wash2. 20048 Make sure no moisture has condensed inside of the unit before installing the lower dome Push gines E the lower dome inside of the back box line up AT LEN SS _ the mounting screw holes and reinstall the mounting screws a 20029 11 12 MAINTENANCE Clean the acrylic dome as needed Be careful not to scratch the surfaces of the dome Exterior Surface Clean the dome s exterior surface with a nonabrasive cleaning cloth and agent that is safe for acrylic plastic Either liquid or spray cleaner wax suitable for fine furniture is acceptable Interior Surface Except Chrome or Gold Clean the same as the exterior surface Interior Surface Chrome or Gold The inside surface of a chrome or gold dome is easily scratched Use the following precautions to maintain the dome s surface a b Always handle the dome from the outside of its circular flange Never touch the coated inside surface The acid in your fingerprints will eventually etch the coating if the fingerprints are not carefully removed according to the recom mended cleaning procedure in item e If dust or other contaminants accumulate on the dome s interior remove the debris with compressed air Compressed air cans are available from photographic equipment or electronic supply dealers If heavy residue accumulates and cannot be removed with air pressure rinse with water and immediately dry with air pressure so that water spots
3. NEMA Type 3 3R 3S 4 4X 6 or 6P enclosure it is designed for indoor use only and must not be installed where exposed to rain and moisture Only use replacement parts Pelco recommends After replacing repairing this unit s electrical components conduct a resistance measurement between line and exposed parts to verify the exposed parts have not been connected to line circuitry The installation method and materials should be capable of supporting four times the weight of the unit and equipment The product and or manual may bear the following marks This symbol indicates that dangerous voltage constituting a risk of electric shock is present CAUTION within this unit RISK OF ELECTRIC SHOCK This symbol indicates that there are important DO NOT OPEN operating and maintenance instructions in the literature accompanying this unit Please thoroughly familiarize yourself with the information in this manual prior to installation and operation Pelco Manual C1458M G 5 05 DESCRIPTION DF5 Series domes are discreet surveillance domes that are designed for indoor or outdoor use Models include pendant and in ceiling versions In ceiling models have plenum rated back boxes and can be installed in hard ceilings or standard 2 x 2 ft 6 x 61 cm suspended ceilings Indoor pendant models come in light gray or black finish Outdoor pendant models are light gray only and include a heater that allows operation down to 60 F
4. number CA number if returned continuous motion applications for credit and RA number if returned for repair wo years on Esprit and WW5700 Series window wiper excluding wiper blades All merchandise returned for credit may be subject to a 20 restocking and refurbishing charge Eighteen months on DX Series digital video recorders NVR300 Series network video recorders and Endura Series distributed network based video products Goods returned for repair or credit should be clearly identified with the assigned CA or RA One year except video heads on video cassette recorders VCRs Video heads will be number and freight should be prepaid Ship to the appropriate address below covered for a period of six months ne M If you are located within the continental U S Alaska Hawaii or Puerto Rico send goods to Six months on all pan and tilts scanners or preset lenses used in continuous motion Service Department applications that is preset scan tour and auto scan modes Pelco 3500 Pelco Way Pelco will warrant all replacement parts and repairs for 90 days from the date of Pelco Clovis CA 93612 5699 hipment All goods requiring warranty repair shall be sent freight prepaid to Pelco Clovis California Repairs made necessary by reason of misuse alteration normal wear or accident If you are located outside the continental U S Alaska Hawaii or Puerto Rico and are are not covered under this warranty instructed to r
5. will not remain Avoid wiping the coated surface with direct hand pressure it will easily abrade unless extreme care is taken Once scratched the dome cannot be repaired If internal wiping is necessary avoid hand rubbing Instead make a wick as follows Use a very soft paper towel Roll a section into a tightly wound tube Tear the tube in half and wet the fuzzy end of the wick with a solution of isopropyl alcohol diluted with water Hold the dome with its opening facing downward and wipe the interior of the dome with the wet end of the wick Use a circular motion starting from the outside and spiraling into the center Use a new wick for each two passes over the dome Pelco Manual C1458M G 5 05 SERVICE MANUAL If you need to service your unit obtain a service manual in one of the following ways Go to Pelco s web site at www pelco com and find service manual C1458SM A Contact Pelco s Literature Department and request service manual C1458SM A Pelco Manual C1458M G 5 05 13 APPENDIX Table A Video Coaxial Cable Wiring Distances RG59 U 750 ft 229 m RG6 U 1 000 ft 305 m RG11 U 1 500 ft 457 m Minimum cable requirements 75 ohms impedance All copper center conductor All copper braided shield with 9596 braid coverage Table B 24 VAC Wiring Distances EXAMPLE An enclosure The following are the recommended maximum distances for 24 VAC applications and are that requires 80 vA and is calculated with a 1
6. 0 percent voltage drop Ten percent is generally the maximum allowable installed 35 feet 10 m from voltage drop for AC powered devices the transformer would require a minimum wire Wire Gauge gauge of 20 AWG 20 18 16 14 12 10 NOTE Models with 10 283 451 716 1142 1811 2880 xe Gc o heute 24 VAC tr MEIEEIESIIE EE the heater The heater uses 42 68 109 174 275 438 g 62 watts of o By the 30 94 150 288 380 603 960 5 camera uses 24 VAC add 3 28 45 72 115 083 292 3 the camera s power to that 5 40 70 1121179 285 452 720 S of the heater and refer to a 21 64 64 69 1037 219 Table B to determine the S 50 56 90 143 228 362 576 E size of wire to use lt 17 27 43 69 110 175 E r 60 47 75 119 190 301 480 g NOTE Distances are e 14 22 36 57 91 146 8 calculated in feet values in 70 40 64 102 163 258 411 5 parentheses are meters 12 09 91 49 78 125 E 80 35 56 89 142 226 360 10 17 27 43 68 109 x 90 31 50 79 126 201 320 3 9 15 24 38 61 97 14 Pelco Manual C1458M G 5 05 SPECIFICATIONS ELECTRICAL Input Voltage Input Power MECHANICAL Construction Back Box Mounting Bracket Lower Dome Trim Ring Indoor Outdoor Dimensions GENERAL Environment Operating Temperature Indoo
7. 51 C DomePak models with camera include a 1 3 inch format high resolution color or mono chrome camera See list of available models below MODELS DF5CA PG 02 3A LJ LI DF5 Series dome C Color camera M Monochrome camera Blank No camera A 24 VAC camera power NTSC standard color EIA standard monochrome Blank No camera PB Pendant black PG Pendant light gray Blank In ceiling back box 0 Smoked dome 1 2 f stop of light loss 1 Clear dome 2 Chrome dome 2 f stops of light loss 3 Gold dome 2 f stops of light loss EO Outdoor pendant includes heater and sun shield light gray smoked dome 1 2 f stop of light loss El Outdoor pendant includes heater and sun shield light gray clear dome 2 3 2 3 mm lens 2 8 2 8 mm lens 4 4mm lens 8 8 mm lens V2 2 5 6 mm varifocal lens V3 3 8 mm varifocal lens V35 3 5 8 mm varifocal lens V5 5 40 mm varifocal lens Blank No lens A Auto iris Blank Manual iris Pelco Manual C1458M G 5 05 INSTALLATION CONTENTS Pelco Manual C1458M G 5 05 The DF5 shipping carton contains two boxes Inspect each box to make sure all parts are present IN CEILING MODELS Back Box 1 Back box with tilt table assembly installed includes camera and lens if specified with order 1 Parts bag 1 Conduit fitting with lock nut 1 Safety chain bracket 1 Compass tool 1 Flat washer models without c
8. 59M Deleted exploded assembly diagrams which are included in C1458SM Changed manual pagination C1458M D 5 98 Revised model numbers Revised camera installation instructions Removed all material relating to the DF5C and DF5M models Revised the procedures under Section 3 7 Lower Dome Installation Revised one Note and deleted another under Section 4 1 Pendant Mount Installtion Added a Note in Section 4 2 Surface Mount Installation 6 98 Revised Section 4 1 and Figures 9 and 11 because of modifications to top mount C1458M E 5 00 Revised installation instructions and illustrations Revised camera installation instructions removed references to obsolete camera models Updated manual to new format C1458M F 1 02 Revised installation instructions and illustrations Added illustrations to show power connections for outdoor models C1458M G 8 02 Added CE certification Revised Important Safeguards and Warnings 5 05 Revised dimension drawing callout from 7 25 18 13 to 7 25 18 41 Pelco the Pelco logo Spectra Genex Legacy DomePak Copyright 2005 Pelco Esprit and Camclosure are registered trademarks of Pelco All rights reserved Endura and ExSite are trademarks of Pelco 16 Pelco Manual C1458M G 5 05
9. Coming from the circuit board are a black wire and a red wire with spade lugs on the end Connect these to the power connectors on the camera BAAT TINAA POSITION AND SET UP CAMERA PowERiNPUT TO CAMERA Turn on power and adjust the tilt table for desired OUTDOOR MODELS 20049 viewing of the camera on the monitor Refer to the camera and lens manuals to set up the camera and lens for proper operation Pelco Manual C1458M G 5 05 LOWER DOME INSTALLATION IN CEILING MODELS LOWER DOME INSTALLATION PENDANT MODELS Pelco Manual C1458M G 5 05 o e 1 Remove the two mounting screws Push the lower Snap the clip on the end of the trim ring leash into the hole on the lip of the back box Line up the snaps on the trim ring with the mounting screws on the back box Snap the trim ring into the plastic snap washers on the mounting screws 20031 dome inside of the back and make sure the lens does not touch the lower dome If the lens touches the lower dome readjust the tilt table Lightly apply O ring lubricant to the O ring Install the O ring in the groove of the trim ring Attach the trim leash to a retainer screw inside of the lower dome Outdoor Models Turn off power Plug the two pin heater connection in the lower dome into the mating connector in the back box Turn power on PLUG HEATER CONNECTIONS NEAREST 7 MOUNTING RETAINER SCREW HOLES SCREW FRONT amp BACK
10. DF5 Series Fixed Mount Dome Installation Operation Manual C1458M G 5 05 Pelco 3500 Pelco Way Clovis CA 93612 5699 USA www pelco com In North America and Canada Tel 800 289 9100 or FAX 800 289 9150 International Customers Tel 1 559 292 1981 or FAX 1 559 348 1120 CONTENTS Section Page IMPORTANT SAFEGUARDS AND WARNINGS ccccsccccsssececssseeecssseeecssseeesseeeessseeeees 3 DESGRIPTION 5 ies oe hri ci Pere EU ea teer tes Ere a Ee e ea ee ue EN Edda 4 MODELS 4 INSTALLATION 5 CONTENTS wd INZCEILING MODELS 2 5 tt otters rnt vot eer He rc ee ter t iin etti nals 5 PENDANT MODELS 3 cct secet Pneu Ert er c Cere reve e e tot enit t t d 5 BACK BOX INSTALLATION IN CEILING MODELS HARD CEILING 6 BACK BOX INSTALLATION IN CEILING MODELS SUSPENDED CEILING 7 BACK BOX INSTALLATION PENDANT MODELS PENDANT MOUNT 8 BACK BOX INSTALLATION PENDANT MODELS SURFACE MOUNT 2 9 CAMERA AND LENS INSTALLATION eese n LOWER DOME INSTALLATION IN CEILING MODELS eene 11 LOWER DOME INSTALLATION PENDANT MODELS seen 11 MAINTENANCE ttr t iet e ot rnit aetati ta t de deer SERVICE MANUAL APPENDIX CEP 14 sldseldeuiem 15 WARRANTY AND RETURN INFORMATION eese tnnt 16 LIST OF TABLES Table Pag
11. amera 1 Split lock washer models without camera 1 Screw models without camera Lower Dome 1 Acrylic lower dome with trim ring PENDANT MODELS Back Box 1 Back box with tilt table assembly installed includes camera and lens if specified with order 1 Parts bag models without camera 1 Flat washer 1 Split lock washer 1 Screw Lower Dome 1 Acrylic lower dome with trim ring 1 Parts bag 1 O ring 1 O ring lubricant 1 Thread compound anti seize lubricant BACK BOX INSTALLATION IN CEILING MODELS HARD CEILING e PREPARE CEILING Locate the center point of the mounting location Drill a hole in the ceiling using a 3 32 inch drill Insert the compass tool into the hole Use a pencil and the compass tool to draw a circle on the ceiling Carefully cut out the circle 20037 20039 20040 INSTALL THE BACK BOX Attach the conduit fitting lock nut and safety chain bracket Install a safety chain cable not supplied that will support up to 16 pounds 7 3 kg Install one end of the safety chain cable to the safety chain bracket and the other end to a support structure in the ceiling ATTACH SAFETY CHAIN HERE 20033 Prepare the wiring for camera and lens power refer to Tables A and B in the Appendix for wiring distances Pull wiring into the back box through the conduit fitting Compress the spring clips on the back box and push it through the hole until the clips sprin
12. e A Video Coaxial Cable Wiring DISIAN S Aresen ah 14 B 24 VAC Wiring DistanCeS i srne tte te ra OE AEE 14 Pelco Manual C1458M G 5 05 IMPORTANT SAFEGUARDS AND WARNINGS Observe the following WARNINGS before installing and using this product 10 11 12 13 Read these instructions Keep these instructions Heed all warnings Follow all instructions Do not block any ventilation openings Install in accordance with the manufacturer s instructions Do not install near any heat sources such as radiators heat registers stoves or other apparatus including amplifiers that produce heat Only use attachments accessories specified by the manufacturer Use only with the cart stand tripod bracket or table specified by the manufacturer or Sold with the apparatus When a cart is used use caution when moving the cart appara tus combination to avoid injury from tip over Refer all servicing to qualified service personnel Servicing is required when the appara tus has been damaged in any way such as power supply cord or plug is damaged liquid has been spilled or objects have fallen into the apparatus the apparatus has been exposed to rain or moisture the apparatus does not operate normally or the apparatus has been dropped To reduce the risk of shock do not perform any servicing other than that contained in the operating instructions unless you are qualified to do so Unless the unit is specifically marked as a
13. ers inside of the back box PREPARE THE CEILING SURFACE Using the back box as a template mark the three 22 fastener holes and the center hole for wiring Make the holes for the fasteners and wiring PREPARE WIRING Bring a coaxial cable for the camera through the center hole in the mounting surface Also bring wiring for power through the hole Refer to Tables A and B in the Appendix for wiring distances INSTALL THE BACK BOX If you are installing the mount outdoors apply sealant around the holes in the mounting surface Position the back box over the mounting holes and pull the wiring into the back box Secure the back box to the mounting surface with appropriate hardware for your installation Reinstall the tilt table assembly 20043 10 CAMERA AND LENS INSTALLATION If the camera and lens are installed already start at step 2 1 INSTALL CAMERA AND LENS If applicable extend the lens to the maximum length before installing the camera in the back box Attach the camera to the tilt table with the 1 4 20 screw flat washer and lock washer supplied IN CEILING MODEL PENDANT MODEL 2 CONNECT CAMERA POWER Indoor Models Connect power wires and video cable to the camera Outdoor Models Connect video cable to the camera Connect power wires to the circuit board mounted on the side of the back box Connect the wires to the connectors marked AC IN HI line voltage AC IN NT neutral and GND
14. eturn goods to the USA you may do one of the following Pelco assumes no risk and shall be subject to no liability for damages or loss resulting from If the goods are to be sent by a COURIER SERVICE send the goods to he specific use or application made of the Products Pelco s liability for any claim whether Pelco based on breach of contract negligence infringement of any rights of any party or product 3500 Pelco Way iability relating to the Products shall not exceed the price paid by the Dealer to Pelco for Clovis CA 93612 5699 USA such Products In no event will Pelco be liable for any special incidental or consequential damages including loss of use loss of profit and claims of third parties however caused If the goods are to be sent by a FREIGHT FORWARDER send the goods to whether by the negligence of Pelco or otherwise Pelco c o Expeditors he above warranty provides the Dealer with specific legal rights The Dealer may also have ER EET CA 94080 USA additional rights which are subject to variation from state to state Phone 650 737 1700 Fax 650 737 0933 REVISION HISTORY Manual Date Comments C1458M 4 97 Original version C1458M A 7 97 Added indoor pendant models C1458M B 12 97 Added DF5C and DF5M pendant models Added outdoor pendant models Removed column for 22 gauge wire from Table B Added dimensions for pendant models to Figure 17 C1458M C 2 98 Deleted references to SD5 P which is covered in C14
15. g back Tighten the screws until you hear a clicking noise CEILING 20036 20035 Pelco Manual C1458M G 5 05 BACK BOX INSTALLATION IN CEILING MODELS SUSPENDED CEILING NOTE The ceiling tile cannot be thinner than 0 50 inch 1 27 cm or thicker than 1 75 inches 4 45 cm Pelco Manual C1458M G 5 05 Q PREPARE CEILING TILE Remove the ceiling tile from the ceiling Insert the compass tool supplied into the center of the tile If necessary use a 3 32 inch bit to drill a hole Draw a circle on the tile using the compass tool and a pencil Carefully cut out the circle 20032 INSTALL THE BACK BOX Attach the conduit fitting lock nut and safety chain bracket Attach to the bracket one end of a safety chain cable not supplied that will support up to 16 pounds 7 3 kg Do not attach the other end yet ATTACH SAFETY CHAIN HERE 20033 Compress the spring clips on the back box and push it through the hole until the clips spring back Tighten the screws until you hear a clicking noise Reinstall the ceiling tile Remove adjacent ceiling tile Prepare the wiring for camera and lens power refer to Tables A and B in the Appendix for wiring distances Pull wiring into the back box through the conduit fitting Attach the safety chain to a support structure Replace the adjacent ceiling tile CEILING
16. r Outdoor Weight In ceiling without camera Pendant without camera 24 VAC outdoor models only 62 VA for heater Aluminum Steel Acrylic Eggshell white molded plastic UL94V0 Aluminum See dimension drawing Indoor or outdoor depends on model 32 to 120 F 0 to 49 C 60 to 122 F 51 to 50 C continuous operation 50 to 122 F 46 to 50 C continuous operation prevents icing 40 to 122 F 40 to 50 C continuous operation de ices within 3 hours after power up 2 80 Ib 1 27 kg 4 25 lb 1 93 kg Add 1 50 0 68 kg for heater and sun shield Assumes no windchill factor for detailed test conditions contact Pelco CAMERA Maximum Camera and Lens Size 5 00 L x 2 75 W x 2 75 H 12 70 x 6 99 x 6 99 cm CERTIFICATIONS RATINGS UL cUL NEMA 1 IP 20 NEMA 4 IP 66 7 25 18 41 6 6 16 76 5 90 14 99 8 25 20 96 20050 Pelco Manual C1458M G 5 05 Models DF5 0 DF5 1 DF5 2 DF5 3 DF5PB 0 DF5PB 1 DF5PG 0 DF5PG 1 DF5PG E0 DF5PG E1 In ceiling models Pendant models TOP PORTION OF BACK BOX DOME IS SECURED IS REMOVABLE FOR SURFACE TO CEILING BY MOUNT APPLICATIONS MOUNTING BRACKET d 10 90 27 69 5 90 14 99 20051 15 PRODUCT WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace without charge any merchandise proved defective in material or If a
17. warranty repair is required the Dealer must contact Pelco at 800 289 9100 or workmanship for a period of one year after the date of shipment 559 292 1981 to obtain a Repair Authorization number RA and provide the following information Exceptions to this warranty are as noted below 1 Model and serial number 2 Date of shipment P O number Sales Order number or Pelco invoice number Five years on FT FR8000 Series fiber optic products 3 Details of the defect or problem e Three years on Genex Series products multiplexers server and keyboard If there is a dispute regarding the warranty of a product which does not fall under the Three years on Camclosure and fixed camera models except the CC3701H 2 warranty conditions stated above please include a written explanation with the product CC3701H 2X CC3751H 2 CC3651H 2X MC3651H 2 and MC3651H 2X camera models when returned which have a five year warranty Method of return shipment shall be the same or equal to the method by which the item was wo years on standard motorized or fixed focal length lenses received by Pelco wo years on Legacy CM6700 CM6800 CM9700 Series matrix and DF5 DF8 Series ixed dome products RETURNS In order to expedite parts returned to the factory for repair or credit please call the factory at wo years on Spectra Esprit ExSite and PS20 scanners including when used in 800 289 9100 or 559 292 1981 to obtain an authorization
Download Pdf Manuals
Related Search