Steam Iron Power Life Successor GC2860
Contents
1. Service Service Service Philips Consumer Lifestyle PRODUCT INFORMATION Features Clour Magenta Powerglide soleplate coating Pointed tip soleplate Steam output 32 g min Steam boost 95 g min Steam level control 3 settings Drip stop system Spray feature Tank capacity 270 ml Cord length 2m 360 degrees ball swivel Filling door Double active calc clean feature Vertical steam 95 g min Rubber bumper Electronic safety shut off Safety Information This product meets the requirements regarding interference suppression on radio and TV After the product has been repaired it should function properly and has to meet the safety requirements and legal regulations as officially laid down at this moment TECHNICAL INFORMATION Voltage 220 240 V Frequency 50 60 Hz Power 1830 2200 W Dimension F box 328 mm x 129 mm x 163 mm Width x Depth x Height Product net weight 1 24 kg Published by Philips Domestic Appliances and Personal Care 09 07 Printed in the Netherlands Steam Iron Power Life Successor GC2860 Water Advice In case you live in an area with hard water e g water hardness more than 8 dGH it is recommended to use a mixture of 50 tap water and 50 demineralized water Powerglide Soleplate Silver solgel coating for more robust scratch resistance smooth gliding amp easy to clean Pointed Tip This feature allow2. Ba 2 3 Tat ion o 7 a THERMOSTAT DIAL PRINTED 21 GC2860 WATER TANK ASSY 7 COVER 3 INSULATION SHEET 23 DOSING SEAL 13 SOS SEAL 14 SOLEPLATE MOUNTED ASSY I Disassemble THERMOSTAT DIAL PRINTED 21 Remove screws C 3x Disassemble WATER TANK ASSY 7 Remove screws D 3x Disassemble COVER 3 Note for re assembly Please ensure that INSULATION SHEET 23 is put in place during re assembly This metal part acts as a heat sink to prevent softening of COVER 3 plastics at the screw location D1 2 5 REPAIR INSTRUCTIONS Due to the high wattage of the iron only the specified cord set must be used Should damage be observed on the CORDSET 22 it must be replaced Continued usage is not allowed GC2860 After the product has been repaired it should function properly and has to meet the safety requirements amp legal regulations as laid down amp officially established at this moment The following tests are common checks that are conducted on a repaired product before it is returned to the consumer 1 Soleplate temperature Check that soleplate temperature is within IEC requirement Measure the temperature of the soleplate after the iron has reached steady state i e connected to the mains for at least 15 minutes The table below shows the temperature requirement Soleplate temperature Deg C Marking Material for example i Minimum Maximum Nominal Tolerance Test
3. e ldot 70 120 95 25 Acetate elastane polyamide polyproylene point ee 2 dots 100 160 130 30 Cupro polyester silk triacetate viscose wool eee 3 dots 140 210 175 35 Cotton linen Pr sA 2 Leakage current Check that leakage current is within IEC requirement Measure leakage current between LIVE NEUTRAL amp EARTH IEC requirement is that at 230 V supply the EARTH leakage current must be less than 0 75 mA 3 Water leakage Functionality 4 Loose part Check that there is no water leakage from any part of the product during operation Check that the functionality of the product product dependent eg steaming variable steam SOS ASO etc is working properly Check that there are no loose parts eg extra screw in the product that can cause short circuit or product malfunction 3 5 PARTS LIST Pos Service code Description 1 4239 021 52820 Soleplate mounted assy 230 V 2000 W 2 4239 015 70150 Ryton ring 3 4239 026 34230 Cover molded 4 4239 026 13220 Thermostat bush 5 4239 021 50160 Lamp assy 6 4239 015 55800 Tank top seal 7 4239 021 54040 Water tank assy GC2860 Australia 8 4239 026 34260 Plastic rattle spring 9 4239 021 43960 Spray pump 10 423902148990 SOS pump 11 4239 020 85140 Valve bellow assy 12 4239 02150220 Steam shaft assy 13 4239 015 58300 Dosing seal 14 4239 015 58310 SOS seal 15 4239 026 34320 SOS knob 16
4. 4239 026 34330 Spray knob 17 4239 02151880 Inlay ASO assy 18 4239 02151910 Filling door assy 19 4239 026 34370 Backplate Soft Touch 20 4239 026 34650 Ball swivel now white 21 4239 021 53580 Thermostat dial printed Eng 22 4239 000 08670 Cord set Australia 23 4239 010 10290 Insulation sheet 24 4239 026 34630 Steam slider 25 4239 021 50690 ASO NZ n z Blue i RESISTOR HEATING HJ INPUT UNIT aw lt gt E g F Lamp z rue o d THERMOSTAT GC2860 4 5 EXPLODED VIEW GC2860
5. s soleplate to reach tricky area Steam Boost The steam boost helps to remove stubborn wrinkles Drip Stop The water tank bottom has a valve that is controlled by a bimetal disc on the soleplate Water is only released into steam chamber via the tank valve when the soleplate temperature is high enough When the soleplate temperature is too low the tank valve is closed This prevents water from dripping onto the garment Double Active Calc Clean Function Protects the iron from scale build up via anti calc tablets within the water tank amp the calc clean function Vertical Steam This features a steam boost in vertical position to remove wrinkles in hanging garments Electronic Safety Shut Off The power to the heating element is cut off when the iron has been motionless The ASO pilot light starts blinking When the iron is moved it is automatically switched on Copyright reserved PHILIPS Subject to modification DISASSEMBLY ADVICE BACKPLATE 19 CORDSET 22 BALL SWIVEL 20 Remove screw A Disassemble BACKPLATE 19 Disconnect 3x quick connectors of CORDSET 22 Disassemble CORDSET 22 FILLING DOOR ASSY 18 INLAY PRINTED 17 SOS KNOB I5 SPRAY KNOB 16 SPRAY PUMP 9 SOS PUMP 10 LAMP ASSY 5 FILLING DOOR ASSY 18 screw B rear catch of INLAY PRINTED 17 INLAY PRINTED 17 2x quick connectors of LAMP ASSY 5 LAMP ASSY 5 a 8 26 O09 J a BoB a D OQ 8 D o O o n 6 5 6 fe
Download Pdf Manuals
Related Search