REFRIGERATORS AND FREEZERS
Contents
1. Do not store open containers with liquids inside the unit This will increase the amount condensation inside and outside of the unit and the evaporator coil will freeze up Do not store hot products inside the unit This will increase the amount of condensation inside and outside of the unit and the evaporator coil will freeze up The unit must be level and on a strong surface When moving the unit check the drain piping to make sure t was not disconnected or moved out of the drain pan This will not be covered under warranty Page 23 For Customer Service Call 1 877 693 3372 www edesausa com REACH INS OPERATIONAL SERVICE MANUAL Rev July TROUBLE SHOOTING Follow the next steps before requesting warranty service Failure to do so may result in service charges for you and may void your warranty 1 Refrigerator doesn t work a Check that the machine is still connected b Check that the ON OFF button is in the ON position 2 Refrigerator doesn t reach temperature a Verify unit is not on saving mode Check that the thermostat is not in OFF position Check that the machine is not in the defrost cycle d Ensure Equipment is in a ventilated place and removed minimum of 2 inches from any other appliance and away from any heat source The environment maximum temperature must be 38C 100F f To insure proper air flow product must not be placed higher than the maximum level mark located on the internal wall of the unit g I2. ELECTRICAL CONNECTIONS Page 8 For Customer Service Call 1 877 693 3372 www edesausa com REACH INS OPERATIONAL SERVICE MANUAL Rev July Refer to the amperage data in this manual or on data plate and your local code or the National Electrical Code to be sure unit is connected to the proper power source Verify correct incoming voltage according to the Data Plate information Do not under any circumstances cut or remove the ground prong from the power cord Fagor units must be properly grounded NEVER USE AN EXTENSION CORD Fagor will not warranty any unit that has been connected to an extension cord Fagor equipment must be grounded and connected in accordance with NEC Article 422 Appliances DANGER Power must be turned off and disconnected from the power source whenever performing maintenance repair or cleaning the condensing unit If machine is still running when power is off disconnect power at the circuit breaker before unplugging the machine WARNING Machine and compressor warranties are void if failure is due to improper electrical installation SHELVING INSTALLATION Hook shelf rails onto shelf pilasters Position all shelf rails equal in distance from the floor for level shelves Wire shelves are oriented so that cross support bars are facing down Note Single door Reach ins include an airflow guard on the rear of the shelves as well as a lip to maintain an air space at the rear of the cabinet Place s
3. CAREL PJEZ S COM VC Ne NA mi Vi gt For Customer Service Call 1 877 693 3372 www edesausa com Page 27 OF 2 QVF 2 Descripci n Description Simbolo a am Ventilador de Evaporador Evaporator s Fan Compresor C ompressor Color AWG Size JE 7 y O CE is AWG EECHER TEE Azul Claro Light Blue 18 AW D sawo ET wawo F Contactor Auxiliar Contactor EE CE Controlador El ctronico Electronic Controller MP Micro interruptor Puerta Door Micro Switch Interruptor Principal Maim Switch Sensor Deshielo Defrost Sensor Amarillo Yellow G Resistencia de Marco Frame Resistance INT L Interruptor Lampara Ligth Switch 18 AWG EA Ground Tierra geed 16AWG I Line Linea Neutre Neutro i EZ mawe x i SEE EE ES ie wawo m For Customer Service Call 1 877 693 3372 www edesausa com Page 28 QR 1G QVR 1G e ER ENE sg CE CAREL PJEZ C For Customer Service Call 1 877 693 3372 www edesausa com Symbol Ground Tierra Line Linea Neutre Neutro EEN EE Color Est ndar Standard Calibre AWG Color AWG Size ocn sawa 3 Pancita wawo o MEET EEN NEL EET EED NE owo C amome wane E mama awo Tu Page 29 QR 2G QVR 2G n a Descripci n Description Resistencia de Descarche Defrost Resistance Color AWG Size Marr n Brown Azul Obscuro Dark Blue Descripci n Description Ventilador de Evaporador Evaporator s Fan C V vi
4. ONE 1 ENE Ts ont Verde Green 18 AWG A wawo 8 sao save DT sawo E 7 SE Se Color Est ndar Standard Calibre AWG Ref Color AWG Size i Ventilador de Evaporador Evaporator s Fan Compresor Compressor Ventilador de Condensador Condenser Fan Lampara Light Controlador El ctronico Electronic Controller MP Micro interruptor Puerta Door Micro Switch INT Interruptor Principal Main Switch RM Resistencia de Marco Frame Resistance Tl Sensor de Ambiente Environment Sensor T2 Sensor Deshielo Defrost Sensor INT L Interruptor Lampara Ligth Switch EA Ground Tierra isawG 1 Eq NE SCH RS yy e e Blanco White 18 AW J Line Linea Neutre Neutro Blanco White mawo Negro Black 14 AW awe Ju CAREL PJEZ C COM VC RDE Lc Ina kom F RM E py B For Customer Service Call 1 877 693 3372 www edesausa com Page 26 QR2 QVR 2 ENE TEI Color Estandar Standard Calibre AWG Color AWG Size Ara a de Conexi nes Juction Box A Aas scuba ae awo 87 EEE sawo E ME E e Mise tenor Paena Door Mico Sch ST rcs Sich ase de MSF Resse Sensor de Ambiente Environment Sensor Sensor Deshielo Defrost Sensor Interruptor Lampara Ligth Switch G SCH Amarillo Yellow 18 AWG Rojo Red isawG H e N Ground Tierra Negro Black 16 AWG EZ m Blanco White 18 AWG J Blanco White 14 AWG K Negro Black 14 AWG O Ae AO at
5. display Release the button and press the SET button one time Now you will see the number zero 0 With the button UP arrow set a value of 22 and then press the SET button You will see the PS again Use the button DOWN arrow to find the parameter EZY and press the SET button one time Using the UP or DOWN button set a value according to the chart below Page 11 For Customer Service Call 1 877 693 3372 www edesausa com REACH INS OPERATIONAL SERVICE MANUAL Rev July EZY Value Application For Refrigerators EZY Value Application Temperature in F Temperature in F Refrigeration Temperature in C Temperature in C A Refrigeration Temperature in F Refrigeration Temperature in C Pa Refrigeration Note Freezer equipment can be used like a refrigerator by selecting the value of the parameter EZY according to the chart above Refrigerators must never be used like a freezer After you chose the value for the EZY parameter press and hold the SET button for 5 seconds You will see the temperature on the display in F or C according to your selection Other functions Manual Defrost To select manual defrost hold the button DOWN arrow for 5 seconds The snowflake icon will appear on the display When this icon is solid it indicates that the equipment is in Defrost mode To exit manual defrost hold the DOWN button arrow for 5 seconds The snowflake icon will turn off Wait 2 minutes for the compr
6. equipment fan assembly or any other electrical or mechanical component Exclusions from and Conditions to Warranty Coverage This Warranty does not cover parts or accessories which a carry the warranty of a supplier or b are abused Application of this Warranty is further conditioned upon the following Installation The Equipment must be properly installed in accordance with Fagor s installation procedures and by a professional technician No Alteration The Equipment must not have been modified or altered from its condition at the date of original installation Use FAGOR EQUIPMENT IS NOT DESIGNED FOR PERSONAL FAMILY OR HOUSEHOLD PURPOSES AND ITS SALE FOR SUCH PURPOSES IS NOT INTENDED IN THE EVENT THE EQUIPMENT IS SO USED THIS WARRANTY SHALL BE NULL AND VOID AND THE EQUIPMENT SHALL BE DEEMED TO HAVE BEEN SOLD AS IS WHERE IS WITHOUT ANY WARRANTY OF ANY KIND INCLUDING WITHOUT LIMITATION ANY WARRANTY OF TITLE NON INFRINGEMENT MERCHANT ABILITY OR FITNESS FOR A PARTICULAR PURPOSE Proper Maintenance and Operation The Equipment must be properly maintained and operated in accordance with Fagor s maintenance and operating procedures All service labor and parts must be acquired from Fagor or its authorized service representative for the User s area This warranty is void if failure is a direct result of handling and or transportation fire water accident misuse acts of god s attempted repair by unauthorized persons improper
7. installation if serial number has been removed or altered or if unit is used for purpose other than it was originally intended Failure to comply with any of these conditions will void this Warranty In addition this Warranty does not cover defects due to apparent abuse misuse or accident For Customer Service Call 1 877 693 3372 www edesausa com Page 31 Parts Warranty Coverage Fagor warrants all new machine parts produced or authorized by Fagor to be free from defects in material and workmanship for a period of 90 days from the Warranty Commencement Date If any defect in material and workmanship is found to exist within the warranty period Fagor will replace the defective part without charge Defective parts become the property of Fagor Fagor will have no responsibility to honor claims received after the date the applicable Warranty expires Notwithstanding the foregoing any claim with reference to the Equipment or any parts therefore for any cause shall be deemed waived unless submitted by the User to Fagor within 30 days after the date the User discovered or should have discovered the claim In connection with all claims under this Warranty Fagor will have the right at its own expense to have its representatives inspect the Equipment at the User s premises and to request all of the User s records pertaining to the Equipment to determine whether a defect exists whether the conditions set forth in this Warranty have been satisfied a
8. FAGOR D REFRIGERATORS AND FREEZERS Manual for installation use and maintenance REACH INS OPERATIONAL SERVICE MANUAL Rev July Contents RECEIVING AND INSPECTING THE EOUIPMENT ees ese ee ee ese se ee ee ee ee ese see ee ee ee ee ee ee ee ee ee ee ee ee ee ee ee ee ee ee ee 3 Di oe teers wars ei ee ee EA Inn A 4 INSTALLATION loto 6 OFERA TION SS seeds 10 KANTENAN Gt GE 21 TROUBEESHOOTINGO sandie ici 24 WIRING DIAGRAM S ese eb Ee EE ee Ee EE Ge Ge EE GE EG idos 25 OR Lee ado telcel 25 GR ads 27 A RT e EE 28 OR TO OVA TO EG EE Ee Oe Ge Ge GE AA Ge EE EE ee 29 OR 2E SsONRIE EE 30 NU PTT PAINE EE ET OR N cen EE ER IE AA N N GO as N OE LE Pe Oe 31 For Customer Service Call 1 866 GO FAGOR www fagorcommercial com REACH INS OPERATIONAL SERVICE MANUAL Rev July RECEIVING AND INSPECTING THE EQUIPMENT Upon receiving your new Fagor Refrigerator check the package and the machine for any damages that may have occurred during transportation Visually inspect the exterior of the package If damaged open and inspect the contents with the carrier Any damage should be noted and reported on the delivering carrier s receipt In the event that the exterior is not damaged yet upon opening there is concealed damage to the equipment notify the carrier immediately Notification should be made verbally as well as in written form Request an inspection by the shipping company of the damaged equipment Retain all crating material until i
9. ON the power Never use high pressure water for cleaning the condenser coil Water can damage the electrical components located near or at the condenser coil Do not place filter material in front of condenser coil This material blocks air flow to the coil similar to having a dirty coil If you keep the Condenser clean you will minimize your service expense and lower your electrical costs Failure to maintain a clean condenser coil can initially cause high temperatures and excessive run times Continuous operation with dirty or clogged condenser coils can result in compressor failures This will not be covered under warranty Neglecting the condenser coil cleaning procedures WILL VOID YOUR WARRANTY To put back the condensing unit slide in the unit carefully in BE SURE THE DRAIN PIPE IS LOCATED OVER THE DRAIN PAN Replace front bottom panel Gasket Maintenance Gaskets require regular cleaning to prevent mold and mildew build up and to keep the elasticity of the gasket Gasket cleaning can be done with the use of warm soapy water Avoid the use of chemical cleaning products on gaskets as this can cause them to become brittle and prevent proper sealing Also never use sharp tools or knives to scrape or clean the gasket which could possibly tear the gasket and rip the bellows Gaskets can easily be replaced and do not require the use of tools or authorized service personnel To remove the gasket pull the gasket towards you To replace gaske
10. Y Page 7 For Customer Service Call 1 877 693 3372 www edesausa com REACH INS OPERATIONAL SERVICE MANUAL Rev July 6 For leveling insert shims between the castor and the frame rail Install the desired number of shims Make sure the slot of the shim is in contact with the threaded stem of the castor FIG 2 If more than one shim is used turn the slot of the shim at a 90 angle If shims are installed in line they may slip out Turn the bearing race clockwise to tighten and secure the castor Use provided tool to secure all castors properly FIG 3 FIG 1FIG 2 FIG 3 Optional legs are hand tightened Thread leg into cabinet bottom frame rail The end of the leg is adjustable for easy leveling Caution To avoid damage to lower rail assembly slowly raise unit to upright position Caution When lifting unit remember to leave the cabinet upright for 24 hours before plugging into power source Failure to meet this requirement can cause compressor failure and unit damage LEVELING Set unit in its final location A level cabinet looks better and will perform better Effective condensate removal and door operation will be effected by leveling Machine must be leveled front to back and side to side with a level tool Castors kit will include shims for leveling Insert the shim between the castor and the frame rail See installation of castors Lock front castors so cabinet does not move Ensure drain hose is inside drain pan
11. essor to start Note If the equipment doesn t reach the temperature first verify that the defrost cycle is not ON The unit will go into defrost every six hours for an average of 20 minutes The defrost cycle is time initiated and temperature terminated NOTE Good air flow inside the cabinet is critical Do not block air flow to the fans Allow three inches of space along the front back and sides CAUTION Do not introduce hot foods chemical or corrosive products drugs or open beverage bottles The unit must run for at least 24 hours before any product is placed inside Failure to do so may ice up the evaporator coil Consequently the unit will never reach the desired set point This failure will not be covered under warranty Page 20 For Customer Service Call 1 877 693 3372 www edesausa com REACH INS OPERATIONAL SERVICE MANUAL Rev July MAINTENANCE Stainless Steel Care and Cleaning Proper cleaning of stainless steel requires soft cloths or plastic scouring pads Never use steel pads wire brushes or scrapers Cleaning solutions need to be alkaline or non chloride cleaners Any cleaner containing chlorides will damage the protective film of the stainless steel Chlorides are commonly found in hard water salts household and industrial cleaners If a cleaner containing chloride is used be sure to rinse repeatedly and dry thoroughly upon completion Stainless steel must be cleaned every day with soap and water Extre
12. f FREEZER check that the temperature is not Celsius h Check that the gasket is in good condition and door is sealed i Check thatthe fan is moving Open the door and press and hold door switch for verification j Don t put any food inside until the unit has reached the proper temperature k If FREEZER food must be previously frozen before being placed inside the cabinet Be sure castors or legs were installed oo 3 There is water inside the refrigerator a Check that the drain pan inside the cabinet is in position b Check that there is not food clogging the drain line 4 There is water under the refrigerator a Check that the drain pipe is over the pan b Check that the cabinet is level Warning To insure proper operation of equipment it is recommended that the unit is on for 24 hours prior to the introduction of perishables Page 24 For Customer Service Call 1 877 693 3372 www edesausa com WIRING DIAGRAMS OR 1 QVR 1 ROE Rese recen ET ve Azul Obscuro Dark Blue 18 AWG EE Ground Tierra Line Linea Neutre Neutro Micro interruptor Puerta Door Micro Switch 1 Sensor de Ambiente Environment Sensor Interruptor Principal Main Switch Sensor Deshielo Defrost Sensor Resistencia de Marco Frame Resistance INTL Interruptor L mpara Ligth Switch ve z EN NE a necesi uc o Cea Ector Bec Ca E SS CE CAREL PJEZ S Page 25 For Customer Service Call 1 877 693 3372 www edesausa com QM
13. he outlet of the evaporator at 32 C 90 F For Customer Service Call 1 866 GO FAGOR www fagorcommercial com REACH INS OPERATIONAL SERVICE MANUAL Rev July Wire gauge recommended for 2 voltage drop in supply circuits Voltage Plug Size 60 ft 120 ft az se us 15 5 15P 14 AWG 14 AWG 12 AWG 12 AWG 10 AWG 10 AWG 8 5 9 1 11576071 5150 20 amp 12 awa ug age sawa sawe sawa 6AWG Note Breaker sizes are recommended by the manufacturer to protect the equipment by over load this breaker only must be dedicated for the equipment If the equipment is installed far away of the circuit breaker these are the wire gauge recommend to connect the appliance if the distance is higher that the chart values please contact an electrician Distance in feet from the breaker or the power supply to the appliance For Customer Service Call 1 866 GO FAGOR www fagorcommercial com REACH INS OPERATIONAL SERVICE MANUAL Rev July INSTALLATION UNCRATING Remove the outer packaging Cut the 4 clamps that hold the refrigerator to the skid Lift the unit off the skid If machine was laid down during this operation remember to leave the cabinet upright for 24 hours before connecting to power source LOCATION Units represented in this manual are intended for indoor use only Be sure the location chosen has a floor strong enough to support the total weight of the unit and its contents For the mos
14. helves on shelf clips making sure all corners are seated properly Page 9 For Customer Service Call 1 877 693 3372 www edesausa com REACH INS OPERATIONAL SERVICE MANUAL Rev July OPERATION For Freezers or Refrigerators with electronic control After connecting your unit turn ON rocker switch located next to the controller The display will light up showing the temperature inside the unit Also the compressor and fan icons will flash for a period of three minutes After this delay the unit will start cooling Compressor Icon Evaporator Fan Icon Temperature inside the cabinet Verify you don t have any alarms on the temperature controller If after you turn ON the equipment the controller shows the alarm icon or an error code call for technical service They will help you fix the problem Note The controller on the equipment is programmed to display internal temperatures in Fahrenheit To change to Celsius see point 4 2 Description of Buttons on the Controller To increase Set Point of Temperature To Turn the unit ON OFF without unplugging the equipment press and hold 3 seconds To Change the set point To access programming mode To decrease Set Point of Temperature To set a manual defrost press and hold 3 seconds Changing the Set Point of the temperature on the controller The unit comes with a factory default set point 8 F Freezers 32 F Refrigerators These set values will make the unit pe
15. i 4 O 4 RSR OM RG Resistencia de Desague Drain Resistance Ventilador de Condensador Condenser Fan CE TA Ti Sensor de Ambiente Environment Sensor Sensor Deshielo Defrost Sensor Interruptor L mpara Ligth Switch Controlador El ctronico Electronic Controller RS 3 see A lt Amarillo Yellow 18 AWG Rojo Red 18 AWG Ground Tierra Negro Black 16 AWG Interruptor Principal Main Switch Resistencia de Marco Frame Resistance Line Linea Neutre Neutro Bianco White 18 AWG Negro Black 14 AWG a as NIS E D For Customer Service Call 1 877 693 3372 www edesausa com Page 30 WARRANTY Limited Warranty Two Years Parts amp Labor Warranty Fagor Commercial Inc Fagor Warrants to the fist end user purchaser the User that the Fagor brand equipment sold hereunder except for parts and accessories which carry the warranty of a supplier the Equipment will be free from defects in material and factory workmanship under normal conditions of use and maintenance for a period of two 2 years from the date of installation Warranty commencement date but in no event to exceed twenty seven 27 months from the date of shipment from the factory Warranty is Not Transferable Warranty Coverage If there is a defect in material or factory workmanship covered by this Warranty reported to Fagor during the period the applicable Warranty is in force and effect Fagor will repair or replace at Fagor s op
16. ll Invoices not paid within the specified terms will be subject to a 1 5 per month delinquency charge Buyer agrees to pay all costs of collection including such attorney s fees as may be allowed by law Taxes This price list does not include any Federal State City or Local taxes which may apply and are subject thereto Shipment Requested carrier will be used upon request Fagor has the right to ship via any responsible carrier if requested carrier is unavailable Shipping charges are payable by consignee and any claims arising as such charges shall be resolved between the carrier and the consignee Shipping dates are approximates Fagor is not responsible for any delays in deliveries that are beyond our control Damaged Merchandise Inspect shipment for any damage before accepting it If damaged open and inspect the contents with the carrier Any damage should be noted and reported on the delivering carrier s receipts Fagor assumes nor responsibility for damages while in transit Concealed Damage If there is concealed damage to the equipment notify the carrier immediately Notification should be made verbally as well as in written form Request an inspection by the shipping company of the damaged equipment Retain all crating material until inspection has been made Cancellations amp Returns Cancelled orders and returned merchandise are subject to a 25 restocking and handling charge Written authorization is required for a return of any eq
17. me stains or grease should be cleaned with a non abrasive cleaner and plastic scrub pad When using a stainless steel chemical cleaner make sure it is recommended for commercial applications Never use an acid based cleaning solution Many food products have an acidic content which can deteriorate the stainless steel finish Be sure to clean ALL food products from any stainless steel surface Failure to do so will result in spots and rust on the surface affected Cleaning the Condenser Coil DANGER Power must be turned off and disconnected from the power source whenever performing maintenance repair or cleaning the condensing unit Disconnect machine Remove front bottom panel and carefully slide out the condensing unit The condenser coil requires regular cleaning It is recommended every 30 60 days depending on the accumulation of dust and grease If the buildup on the coil consists of only light dust and debris the condenser coil can be cleaned with a simple brush Heavier dust build up may require a vacuum or even compressed air to blow though the condenser coil Page 21 For Customer Service Call 1 877 693 3372 www edesausa com REACH INS OPERATIONAL SERVICE MANUAL Rev July If heavy grease is present there are de greasing agents available for coils The condenser coil may require to be sprayed with de greasing agent and then to be dried with compressed air Be sure all electrical and mechanical parts are dry before turning
18. nd whether or not the applicable Warranty is in effect THE FOREGOING WARRANTY IS IN LIEU OF AND EXCLUDES ALL OTHER WARRANTIES NOT EXPRESSLY SET FORTH HEREIN WHETHER EXPRESS OR IMPLIED BY OPERATION OF LAW OR OTHERWISE INCLUDING BUT NOT LIMITED TO ANY REPRESENTATION OF PERFORMANCE AND ANY IMPLED WARRANTIES OF TITLE NON INFRINGEMENT MERCHANTABILITY OR FITNESS FOR A PARTICLULAR PURPOSE NO OTHER WARRANTIES ARE AUTHORIZED ON BEHALF OF FAGOR UNLESS SPECIFICALLY ISSUED BY FAGOR Fagor shall have no liability for incidental or consequential losses damages including without limitation or expenses loss of sales spoiled food profits or goodwill claims whether or not on account of refrigeration failure or punitive or exemplary damages directly or indirectly arising from the sale handling or use of the Equipment or from any other cause relating thereto whether arising in contract tort warranty strict liability or otherwise Fagor s liability hereunder in any case is expressly limited at Fagor s election to repair or replacement of Equipment or parts therefore or to the repayment of or crediting the user with an amount equal to the purchase price of such goods Prices amp Specifications Fagor reserves the right to change the prices and specifications of the equipment and or material without notice Prices are FOB Fagor warehouses All orders are subject to acceptance by Fagor Commercial Inc Terms All orders are subject to credit approval A
19. nspection has been made Contact the dealer through which you purchased the unit Check the compressor compartment housing and visually inspect the refrigeration package Be sure lines are secure and base is still intact A NOTE FROM OUR QUALITY CONTROL MANAGER CONGRATULATIONS ON YOUR NEW PURCHASE WE WOULD LIKE TO WELCOME YOU TO THE FAGOR TEAM THE UNIT IN FRONT OF YOU IS A GREAT PIECE OF EQUIPMENT THAT WILL BECOME ONE OF YOUR MOST RELAIBLE TOOLS IN YOUR DAILY OPERATIONS FOR YEARS TO COME PRIOR TO SHIPPING YOUR UNIT OUR TRAINED SERVICE TECHNICIANS TESTED YOUR UNIT FOR A PERIOD OF 12 HOURS THIS PERFORMANCE TEST WAS RECORDED AND A COPY OF THE RESULTS IS INCLUDED WITH THIS SERVICE MANUAL DURING THIS TEST OUR HIGHLY QUALIFIED PERSONNEL INSPECTED YOUR MACHINE FOR LEAKS LOSE COMPONENTS AND IMPROPER NOISE LEVELS WE ALSO TESTED THE COOLING PERFORMANCE IN AN EFFORT TO GIVE YOU THE BEST AND MOST RELAIBLE UNIT POSSIBLE For Customer Service Call 1 866 GO FAGOR www fagorcommercial com REACH INS OPERATIONAL SERVICE MANUAL Rev July SPECS SCENE Cu Ft Shvls BTU S Hr QR 1 CES EE IR N or2 49 6 3644 239 4048 475 _ opze 4 6 2108 112 1348 475 avez as 6 2108 112 1340 475 avez as 6 ses 239 4048 475 ave 2G6 as 6 2108 112 1340 475 Note The pressure in the suction line is recommended at 32 C 90 F maximum of ambient temperature Superheat measured in t
20. rform at its maximum capacity Therefore it is not recommended to change the set point If set point needs to be changed follow the next steps Note If you change the set point of temperature the performance of the equipment will change Changes made in the parameters of the controller will not be covered under warranty Page 10 For Customer Service Call 1 877 693 3372 www edesausa com REACH INS OPERATIONAL SERVICE MANUAL Rev July Push the SET button for one 1 second You should see a flashing number Release the button 2 Press the up and down arrows to increase or decrease the set temperature Then press the set button to save the new set point Note The maximum value you can set in the controller is Forrefrigerators 5 C 40 F For freezers 16 C 2 F 3 If you wish decrease the value of the set point for a new temperature press the button DOWN arrow see the picture below Press this button to reach the desired value Release the button and then press the SET button to keep and save the new value Note The minimum value you can set in the controller is Forrefrigerators 1 C 30 F For freezers 23 C 8 F Changing the reading temperature from F to C or vice versa To change the reading of the temperature from F to C or vice versa you need access to the programming mode in the controller To do this press and hold the SET button for five 5 seconds until PS is shown in the
21. t efficient operation be sure to provide at least three 3 inches between sides back and top of the unit The unit should not be installed under ambient temperatures higher than 100 F If the relative humidity is higher than 60 the door frames may sweat water This is not a malfunctioning of the unit WARNING The following actions will void your warranty Modification of power cord Connecting the unit to any extension cord Neglecting to install the castors or optional legs Inside cabinet The first cleaning must happen when you unpack the unit and before it is turned ON For this you have to clean the unit with warm water and mild detergent When it is cleaned and dry proceed to install accessories and plug your unit in to a dedicated outlet WAIT 24 HOURS BEFORE PLACING PRODUCT IN THE UNIT This will guarantee that it is working properly Consequential damages are not covered under warranty Outside cabinet Be sure that the unit has access to ample air to breathe Avoid hot corners and locations near stoves and ovens It is recommended the unit be installed no closer than 3 from any wall The place where the refrigerator is placed must be open and clean This will reduce the amount of debris and dirt on the condenser fan and coil Page 6 For Customer Service Call 1 877 693 3372 www edesausa com REACH INS OPERATIONAL SERVICE MANUAL Rev July DATA PLATE The data plate is located inside the cabinet near the
22. t press the gasket against the groove of the door the gasket will snap back into place Doors Hinges During transportation the doors hinges may become loose If the door s don t look aligned tighten the screws that hold the hinge brackets to the frame of the unit If the doors are loose or sagging this can cause the hinge to pull out of the frame which may damage the doors and the door hinges In some cases this fix or adjustment may require a qualified service agent or maintenance personnel Page 22 For Customer Service Call 1 877 693 3372 www edesausa com REACH INS OPERATIONAL SERVICE MANUAL Rev July Drain Maintenance Each unit comes equipped with a drain pan located outside the unit The drain pan catches the condensation produced inside the evaporator coil If the drain hose become loose or disconnected from moving or bumping the unit you may find a puddle of water inside outside of the unit Replace or fix any lose connections IF YOU NOTICE EXCESSIVE WATER ACCUMULATION ON THE INSIDE OF THE UNIT be sure the drain tube is connected firmly and not kinked or bent It is the owner s responsibility to maintain the drain pan leveled and with the drain hose inside of the pan Units installed in a humid environment will produce large amounts of water in the drain pan This is NOT a malfunction of the unit It is the customer s responsibility to clear the drain pan as necessary to avoid puddles of water underneath the unit
23. tion that part ground shipping only of the Equipment that has become defective and will cover labor cost straight time only within the corresponding warranty period of time Fagor shall bear all labor costs straight time only in connection with the installation of these replacement parts provided that the installation is conducted by Fagor or its authorized representative Charges for warranty travel time round trip total two 2 hours or up to 100 miles total Any charges exceeding those stated herein must have prior authorization by Fagor Travel outside of the two 2 hours or 100 miles and any work performed at overtime or weekend rates would be the responsibility of the owner user In the case Fagor deems the equipment non repairable said equipment will be replaced and the replacement unit s will carry the same warranty period from the original unit s installation date original Warranty Commencement Date Additional Three Year Compressor Part Warranty In addition to the warranty set above Fagor warrants the sealed compressor part only for an additional three 3 years based on the installation date This warranty is for defects both in workmanship and material under the normal and proper use and maintenance service The three 3 year extended warranty only applies to sealed parts of the compressor and does not apply to any other part or component including but not limited to cabinet temperature control refrigerant motor starting
24. top front left corner Under no circumstances should the data plate be removed from the unit The data plate is essential to identify the particular features of your machine and it is of great benefit to installers operators and maintenance personnel It is recommended that in the event the data plate is removed you copy down the essential information in this manual for reference before installation Removal of data plate will void the warranty Model re n SERIAL NUMBER FOR THE EOUIPMENT 8 digits and ends in M Electrical Refrigerant Type INSTALLATION OF CASTORS OR OPTIONAL LEGS To obtain maximum strength and stability of the unit be sure that castors are secure and unit is level Inside the unit you will find a Castor kit which includes four castor wheels leveling shims and assembly tool Installation of castors Cut the 4 straps that hold the refrigerator to the pallet Slide out unit until castor holes are exposed CASTORS WITH BRAKES MUST BE INSTALLED IN THE FRONT OF THE UNIT Carefully lift the unit high enough to install the casters Repeat the same operation to install the remaining castors CAUTION NEVER LAY MACHINE ON ITS BACK IF NEEDED LEAVE THE CABINET UPRIGHT FOR 24 HOURS BEFORE CONNECTING TO POWER SOURCE TO AVOID DAMAGE TO LOWER FRAME SLOWLY RAISE UNIT TO UPRIGHT POSITION FAILURE TO MEET THIS REQUIREMENT CAN CAUSE COMPRESSOR FAILURE AND UNIT DAMAGE THIS WILL NOT BE COVERED UNDER WARRANT
25. uipment All equipment returned must be in its original factory crate freight prepaid and must be in the same condition as originally shipped by Fagor Returns will only be authorized within 30 days of invoice date Warranty Register your product with Fagor Commercial to validate you warranty Service calls must be made directly through Fagor service department 1 866 463 2467 or e mail servicerequest fagorcommercial com You may register your product online at http www fagorcommercial com For Customer Service Call 1 877 693 3372 www edesausa com Page 32 FAGOR 2 For Customer Service Call 1 877 693 3372 www edesausa com Fagor Commercial Inc 13105 NW 47th Ave Miami FI 33054 Tel 305 779 0170 Fax 305 779 0173 1 866 GO FAGOR www fagorcommercial com Page 33
Download Pdf Manuals
Related Search