MODEL IHA-96 HEAT ON DEMAND® HEAT ACTIVATOR & BASE
Contents
1. Clean only as directed above Spraying with a hose can get water in the electrical components and cause a short circuit or an electrical shock Condition Overheated Bases The Aladdin Heat on Demand Products are designed with a temperature measurement sensor located under the base guide This sensor should be cleaned weekly due to possible debris accumulation during operation If the sensor is not kept clean the base may be damaged after the initial heating cvcle bv either accidental or intensional re enterina a previouslv heated base Clean sensor weekly by wetting a Q tip with water and lightly swab the sensor Solution Clean Sensor To Clean 1 Wet a Q tip with water soaps or glass cleaner will damage the sensor 2 Swab the middle of the temperature measurement sensor To verify the sensor is clean 1 Place a clean dry base into the guide to be heated 2 After the heating cycle has ended Remove the base 3 Count 3 seconds 4 Place the same base back into the guide and the green ready lamp should glow within 4 seconds or less If not the temperature detection system is not functioning properly contact the Aladdin Technical service department X ELECTRICIAN MAINTENANCE 12 To prevent electrical shock hazard the vented rear access panel must be opened only by a qualified electrician Prior to performing any maintenance service or removing the vented rear access panel insure the Activator is t2. a minimum of 100 pounds safely more if anything else such as Heat on Demand bases are to be placed on the table You may obtain Model IHAT95 Table for Heat Activator which has been designed specifically for use with this system ANWARNING To prevent the possibility of fire place the Activator at least 6 inches from any combustible material with no obstructions within 6 inches of the rear vented access panel After setting the Activator in place plugging it into the proper electrical outlet and turning it on the installer should verify the proper operation of the lights as described in the section immediately following Ifthe lights do not operate as described below the installer should call the Aladdin Temp Rite Service Department In addition to checking for the proper operation of the lights the installer should verify that the yellow light blinks on and off for approximately 10 seconds when the operation switch in the base guide is activated if this does not happen call the Aladdin Temp Rite Service Department Finally the installer should verify that the Heat on Demand base heats properly Approximately 75 to 90 seconds after the base has been activated heated on the Activator for 10 seconds the round grey area in the top center of the base should be in the range of 200 to 250 degrees Fahrenheit 79 to 107 degrees Celsius If this is not the case notify the Aladdin Temp Rite Service Department C Be sure the
3. for the connection of the power cord N WARNING Each Activator is fitted with a grounded power cord and must be connected to a properly grounded receptacle Each receptacle must be wired to a dedicated circuit protected by a circuit protection device rated at not more than 20 amps Ifthe Activator is not grounded a significant electrical shock hazard will exist IHA 96 HEAT ON DEMAND ACTIVATOR The Activator has an on I off switch on the side of the unit near the point where the main power cord is connected Read the following sections of the manual regarding setup and operation before turning the Activator on INWARNING To prevent electrical shock hazard turn the main power switch to the Off O position and disconnect the Activator from the power source whenever performing service or maintenance functions Always turn the Activator Off O and disconnect it from the power supply prior to removing the rear vented access panel It is necessary to do this to prevent electrical shock while performing service B SETTING UP THE EQUIPMENT The Activator has been completely checked at the Aladdin factory prior to shipment to you No adjustments of any sort should be required to place the Activator into service The Activator should be located in a position convenient to the trayline operator and within 6 feet of the prescribed electrical outlet The Activator should be placed on a sturdy table capable of supporting
4. joint inventory and examination of the contents should be made by you and the delivery driver If concealed loss or damage is discovered after you have given the carrier a clear delivery receipt notify the carrier in writing immediately or within 10 days from the delivery date If you phone the carrier you must follow up the call in writing to protect your rights You can only improve your position as a claimant by promptly reporting such loss or damage You should also retain all cartons or containers and include the packing material until an inspection has been made or waived by the carrier Notification of loss or damage does not constitute the filing of a claim You should file your claim in writing with the carrier immediately Carriers will furnish the necessary form upon request You should also request an inspection If a claim is filed by phone always follow up immediately in writing V INSTALLATION NOTE This equipment is to be installed only by a qualified electrician Installation instructions may be obtained from the Aladdin Temp Rite Technical Services Department toll free at 1 800 888 8018 ext 3701 A ELECTRICAL CONNECTION Refer to the specifications data on page 5 the equipment data plate located near the main power switch your local codes and the National Electrical Code to be sure the ACTIVATOR is connected to the proper power source protected circuit of the correct voltage and amperage must be available
5. potentially hazardous situation which if not avoided COULD result in death or serious personal injury CAUTION The word Caution identifies a potentially hazardous situation which if not avoided MAY result in minor or moderate injury The word Caution may also be used to alert against unsafe practices and property damage only accidents NOTE The word Note is used to identify installation operation or maintenance information which is y important but not hazard related LH sPECIFICATIONS A MODEL arse eA IHA 96 B LENGTH EM 23 inches 60 3 cm C WID TFH ose 1634 inches 42 5 cm D HEIGHT Sicid cscs eaei 13 inches 33 7 cm E VOLTAGE eie IDEM MONTE 208VAC F 50 60 HZ G PHASE d hiec due 3 H AMPS c X n 14 I NEMA PLUG eite L21 20P J SHIPPING 71 POUNDS 32 2kg K NUMBER OF WIRES eir ed pe eR DRE Ed 5 L PLUG HUBBELL ONLY TWISTLOCK IV REGULATORY COMPLIANCE amp INDEPENDENT TESTING This equipment has been listed by the following organizations Underwriters Laboratories File Number E67324 National Sanitation Foundation Standard Number 4 This equipment has been verified to comply with the following Code of Federal Regulations Title 47 Section 18 Federal Communications Commission Code of Federal Regulations Title 29 Section 1910 97 Occupational Safet
6. Activator is plugged into the proper outlet as indicated in the specifications on page 5 of this manual Hubbell brand NEMA configuration L21 20P D Be sure there is at least 6 inches of clearance between the Activator and any combustible materials such as paper plastic or cardboard E Be sure there is at least 6 inches of clearance between the rear of the Activator where the vents are and any object which would restrict air flow F Turn the activator on by turning the main power switch located on the left side of the Activator at the rear to the up or on I position When this is done the red power light will glow VILoPERATION A Besure the Activator is plugged into the proper outlet B Be sure there is at least 6 inches of clearance between the Activator and any combustible materials such as paper plastic or cardboard C Be sure there is at least 6 inches of clearance between the rear of the Activator where the vents are located and any object which would restrict air flow D Turn the Activator on by turning the main power switch located on the left side of the Activator at the rear to the up or on I position When this is done the red power light will glow 1 Operator must place an unheated Heat on Demand base in the proper location to start the heating cycle To do this slide the base into the base guide until the heat activation switch 1s fully depressed 2 When the heater activation switch 1s d
7. DEPARTMENT 1 800 888 5426 XV WARRANTY ALADDIN TEMP RITE EQUIPMENT LIMITED WARRANTY Aladdin Temp Rite ATR warrants to the original purchaser that the equipment listed below shall be free from defects in material and workmanship under normal use for the applicable warranty term set forth below ATR s obligation under this warranty is limited to the repair or replacement at the sole option of ATR of any part which upon inspection and examination by ATR or its authorized agent is found to be defective A written description detailing the nature of the claimed defect together with the equipment claimed to be defective if required by ATR must be delivered to ATR or its authorized agent within 30 days of discovery of the claimed defect but in no event later than 30 days after the expiration of the applicable warranty term HEAT ON DEMAND WARRANTY TERMS EQUIPMENT PARTS LABOR HEAT ACTIVATOR IHA 96 1 YEAR 90 DAYS BASES IHB98M IHB98G IHB98E IHB98T IHB98B 2 YEARS N A The warranty term commences 30 days after Aladdins invoice for the equipment THE WARRANTIES AND REPRESENTATIONS OF ATR CONTAINED HEREIN ARE EXPRESSLY IN LIEU OF AND THE BUYER WAIVES ANY AND ALL OTHER WARRANTIES EXPRESS OR IMPLIED INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE AND ANY OTHER REMEDIES AGAINST ATR WHETHER BASED UPON CONTRACT NEGLIGENCE STRICT LIABILITY OR OTHERWISE ATR SHALL
8. Machin Jernp Kite P O Box 2978 Hendersonville TN 37077 2978 1 800 888 8018 or 615 537 3600 Fax 1 888 812 9956 www aladdintemprite com better by degrees MODEL IHA 96 HEAT ON DEMAND HEAT ACTIVATOR amp BASE INSTALLATION OPERATION amp SERVICE MANUAL Manual P N 92682 HEAT ON DEMAND U S Patent 5 603 858 and 5 786 643 other U S Rev E 11 27 2006 and Foreign Pending Please read this manual completely before attempting to operate install or service this equipment Failure to follow these instructions and precautions could cause death injury or equipment damage After receiving inspect all components immediately Notify carrier of damage See page 6 Cpsu5ce pe Wye Pe IJ OLUJS IOU IU ple qOCfIUJGUE UOLTUCSEIOU CobAuSpt 1902 vISqqm Ieunb Eirec IHA 96 HEAT ON DEMAND SYSTEM CONTENTS I a EE 12 1 TP 4 IL SPECIFICATIONS 5 IV REGULATORY COMPLIANCE AND INDEPENDENT TESTING eme 3 V RECEIVING INSPECTIONS 6 VI INSTALLATION 7 OPERATION 9 VII OPERATOR MAINTENANCE H SANITATION amp CLEANING IX ELECTRICIAN S MAINTENANCE 12 TROUBLESHOOTING GUIDE 13 X PARTS ILLUSTRATIONS 14 15 ELECTRICAL SCHEMATIC 16 HEAT ON DEMAND BASE CARE amp HA
9. NDLING 17 XIV SERVICE 19 XV EQUIPMENT WARRANTY 19 IHA 96 HEAT ON DEMAND ACTIVATOR INTRODUCTION The Aladdin Temp Rite Heat on Demand Heat Activator is designed to provide a quick clean and efficient heat source for use with the Aladdin Temp Rite Heat on Demand base The Activator has been specifically created for use ONLY with Aladdin Temp Rite s Heat on Demand bases There is no exposed coil open flame or heated surface The only heat applied to the top surface of the base 1s that which is absorbed from internal component base parts This Activator contains no operator serviceable parts Please consult a qualified electrician or the Aladdin Temp Rite Service Department should the equipment require service Aladdin s toll free service line is 1 800 888 5426 This equipment is to be installed only by a qualified electrician There are no operator serviceable parts inside this Activator Operators should never remove the back panel or fuse access panel of this Activator LL SAFETY If you know how to correctly install operate clean and service the Heat on Demand System your satisfaction with the system will be increased and safety will be enhanced In accordance with generally accepted product safety labeling guidelines the following three signal words are used throughout this manual to alert you to potential hazards and to tell you how to avoid them WARNING The word Warning identifies a
10. NOT BE LIABLE FOR ANY CONSEQUENTIAL OR INCIDENTAL DAMAGES OR ECONOMIC LOSS OF ANY NATURE INCLUDING WITHOUT LIMITATION LOSS OF REVENUES AND OR PROFITS THAT MAY BE CLAIMED TO RESULT FROM ANY NEGLIGENCE OR BREACH OF WARRANTY OR CONTRACT BY ATR Exceptions and Exclusions This warranty is issued only to the original purchaser and is not transferable and applies only to the products installed within the United States of America its territories and Canada During the term of any labor warranty ATR will pay all pre approved shipping charges incurred in returning defective equipment to ATR and labor costs incurred in the removal and reinstallation of such equipment Contact ATR before returning any claimed defective equipment or otherwise performing warranty repairs ATR assumes no liability for any work or repair performed without its prior approval After the expiration of any labor warranty the original purchaser is responsible for all shipping charges incurred in returning defective equipment to ATR and labor for removing and reinstalling such equipment ATR shall not be responsible for the replacement of expendable items like lamps and fuses or product failure resulting from normal wear and tear improper installation misuse sabotage abuse neglect accident unauthorized alterations or repair or other factors beyond the control of ATR Neither this warranty nor the liability of ATR may be modified or extended by action of any agent distributor or o
11. Reset Activator by turning power switch off waiting 15 seconds then turning power switch back on If Activator does not operate properly after resetting call Aladdin Temp Rite Service Department 4 Activator will not run White Incorrect voltage Check voltage at receptacle service light comes on Interrupted power Reset unit Turn the unit off wait 10 seconds amp turn the unit back on 5 Activator stops suddenly Power cord has become unplugged Plug back in power light goes out Power outage Call Facilities Maintenance Do not double cycle base Reset Activator by turning power switch off waiting 15 seconds then turn power switch back on If Activator does not operate properly after resetting call Aladdin Temp Rite Service Department Top is excessively hot Missing air filter Replace air filter immediately Over 185 F Dirty air filter Clean air filter often Activator suddenly stops and Power outage Call Facilities Maintenance will not re start Yellow light does not blink for Base has been heated within the past Use Another Aladdin Heat on Demand base approximately 10 seconds hour and is still hot 9 Green light comes on Base has been heated within the past Use a cool room temp Aladdin Heat on immediately after inserting base hour and is still hot Demand base Timer or IFR malfunction Call Aladdin Temp Rite Service Department 10 Low base temperature lt 200 F Refer to section VI B in manual Calibrate tem
12. actured to function in an institutional environment Through experience we have found certain conditions that may cause premature damage Functional as well as cosmetic difficulty will arise from repeated abuse of the bases The following four precautions listed below will add months to the utility of each base 1 HIGH DISH MACHINE TEMPERATURE Dish machine temperatures should not exceed 190 F Blow dryer temperature should not exceed 200 F Avoid prolonged exposure to heat inside the dish machine CONTINUED ON NEXT PAGE 17 IHA 96 HEAT ON DEMAND ACTIVATOR 2 MISHANDLING Abuse such as striking against metal object or dropping on the edge will shorten the life of the base Should the base become cracked or broken it should be removed from service Continued use could allow the base to absorb water As a safety feature this base is equipped with a pressure release valve to prevent pressure build up should water absorption occur before the base is removed from service 3 HIGH TEMPERATURE Avoid direct contact with open flame or high heat sources such as ovens dish heaters or steam tables To prevent heat damage to the bases DO NOT STACK BASES AFTER ACTIVATION 4 ABRASIVE CLEANERS Do not use cleaners which contain abrasives or abrasive pads to clean bases C STAINING OF THE BASES CAN BE CAUSED BY ANY OF THE FOLLOWING HARD WATER WHICH HAS A HIGH CONCENTRATION OF CALCIUM AND MAGNESIUM SALTS Detergent suppliers can test for wat
13. epressed the yellow panel light will blink indicating the Activator is heating NOTE Do not remove or tamper with the base during the heating cycle while the yellow light is blinking otherwise the activator will automatically stop heating 3 Atthe end of the heating cycle the yellow panel light will stop blinking and a green panel light that signals ready for use will illuminate IHA 96 HEAT ON DEMAND ACTIVATOR NOTE The green light will stay ON I as long as the heated base remains in position A CAUTION Never remove a hot Heat on Demand base and place it back on the Activator before using Never heat a base more than once in a one hour period This will result in a double heating of the base which will cause damage to it 4 The sequence of operation for this equipment is designed to activate a base in 10 seconds 5 Always turn the main power switch to the off 0 or down position at the end of each meal assembly period 6 DO S and DON TS 1 Heat only Aladdin HEAT on DEMAND bases 2 When calling Aladdin for service refer to Model Number IHA 96 and Serial Number shown on the Data Plate on the left side of the unit Never strike Activator surface with sharp objects or heavy weights Never cover bottom of base during activation with paper cloth foil or other material Never place Activator for operation near other equipment with remote controls Never attempt to heat any metal objects o
14. er hardness and make recommendations for appropriate detergents and rinse agents and or water softener LOW DISH MACHINE TEMPERATURE LOW CONCENTRATION OF DETERGENTS POOR WASHING RINSING ACTIONS i e clogged spray jets low water pressure final rinse activator not tripped Proper dish machine maintenance will eliminate most potential problems INADEQUATE SPACING BETWEEN BASES IN THE DISH MACHINE SLIDING OVER A METAL SURFACE MAY LEAVE A STREAK ON THE PLASTIC D PERIODIC MAINTENANCE Bases are equipped with a pressure relief poppet on the bottom In the unlikely event that water has entered the base the poppet allows any water to escape During the periodic inspection of the bases verify the poppet is present If the poppet is missing or damaged the base should be removed from service Pressure Relief Poppet Generally the care and handling procedures previously outlined will prevent any further action Yet sometimes persistent problems call for additional care The bases are generally stain resistant but there are some points to remember The contact surfaces get very heavy wear and stain exposure If staining occurs it is recommended that a special cleaning be performed Commercial destaining formulas are available Please contact your detergent supplier 18 XIV sERVICE In the event service is required on your Aladdin HEAT ON DEMAND Activator please call ALADDIN TEMP RITE SERVICE
15. od a Wipe the top and sides with a clean damp cloth using warm water and mild dishwashing detergent Abrasive pads are not recommended for cleaning b Usea soft nylon brush on any food soil and in corner areas AUTION To prevent 23 to the top surface do not use harsh chemicals or under diluted sanitizers AUTION Never use bleach or AAN containing bleach to clean the stainless steel portions of the Heat Activator The use of this type of product can induce rusting d Inspect and clean the air intake filter see parts illustration page 14 located on the bottom of the Activator in the front with warm water and mild detergent once each month or more frequently if it is heavily soiled To remove the air intake filter turn the Activator off and disconnect it from the power source Turn the Activator on the side and remove the thumbscrew holding the air intake filter in place and lift the filter out The air intake filter may be immersed in water or run through a dish machine Insure that it is thoroughly dry before placing it back in the Activator IHA 96 HEAT ON DEMAND ACTIVATOR Do not operate Activator with the air intake filter removed Foreign particles could enter the Activator and cause an electrical failure If the Activator is operated without the air filter in place it is possible for a person to stick their fingers in the moving fan blade and cause personal injury This Activator is not hose washable
16. oot Bolt M 5 x 10 Pan S S Circuit Breaker 2 Amp Screw M 3 x 45 Pan S S Plate Cover Fuse Bolt M 5 x 25 Plug Electrical 20 Amp 5 wire Twist lock NEMA L21 20 Washer Flat M 3 Nut Sealing Topaz Fuse 20 Amp Bushing Threaded Fan Label Warning Fuse access panel Assembly Light Red Label Caution Assembly Light Green Label Warning Vented Back Panel Assembly Light White Endcap Terminal Block Block Terminal 6 Prong Control Temp IHA96 Base Temp Control Timer Digital Primary IHA96 Sensor IHA96 Housing Plunger Assembly IHA96 Base Timer IHA96 Bolt M5 x 16 Pan slot S S Timer Safety Fixed le flole le din gt je Electrical parts illustrated on the parts illustration wiring schematic and parts list are for purposes of illustration only Only the parts listed on page 15 are replaceable in the field by a qualified electrician All other service work will require that the Activator be returned to the Aladdin Temp Rite factory for service Should the Activator have to be returned for service to the Aladdin factory contact the Aladdin Temp Rite Service Department to make arrangements fora loaner or maintenance float Activator 15 IHA 96 HEAT ON DEMAND ACTIVATOR Xll ELECTRICAL SCHEMATIC CIRCUIT EMI FILTER PUWER SUPPLY xc os Qui 1 gk L ec u
17. p probe 13 IHA 96 HEAT ON DEMAND ACTIVATOR X PARTS ILLUSTRATION 75289 ron 75159 Assy Yellow Vola 75290 Assy Green Light 75291 92728 5 Assy White M 5 x 16 Pan Slot S S Light Assy T 34803 5 75205 2 Cover Screw Black ail M 3 x 6 Pan Slot S S Tu r 75325 2 how M 3 External Starwasher 92739 Switch Guard 75211 4 21042 67178 M 5 x 10 Pan Slot S S Activation Switch Power Switch 34803 4 i Y S e 2 Cover Screw Black a E 75073 8 N M 4x 6 Pan Slot S S a 75214 2 T M 5 x 25 Pan Stot S S 75212 8 fo 34803 2 M 3 x 45mm Pan Slot S S Cover CERA d ack 75325 8 M3 External Starwasher 75215 8 75084 M 3 Flat Washer Circuit Breaker a N v 75211 2 p 75091 Fuse 3 p 92738 1 Cover Plate 75211 4 M 5 x 10 Pan Slot S S Ey 34803 4 75211 4 75074 4 Cover Screw Black M 5 x 10 Pan Slot S S 1 34803 4 Cover Screw Black i 75086 Plug 92771 Air Filter Assembly 1 1 75207 Thumb Screw Assy 14 PARTS LIST Description Part No Description Qty Switch Activation Guard Switch Power Cover Bolt Head Black Assembly Air Filter Switch Power Assembly Thumb screw Panel Back Vented Assembly Light Yellow Base Guide IHA 96 M3x 6 Pan S S F
18. r bases other than Aladdin Heat on Demand bases Never heat an Aladdin Heat on Demand base that has been heated within the past hour Never heat Aladdin Heat on Demand Bases in the microwave oven Never stack bases after activation Never Heat a base with a dish in it Never power up the activator with a base present on the surface Otherwise the service lamp will glow and the unit must be reset without the base present Never strike Aladdin Heat on Demand bases against any hard surface to clean Use caution when scraping base prior to warewashing Never heat an Aladdin Heat on Demand base missing the pressure relief poppet Any base found without a poppet should be removed from service VIII OPERATOR MAINTENANCE 7X WARNING Electrical hazard inside the operator should never open the back panel or fuse access panel of this activator The back panel should only be opened by a qualified electrician who has read the service and installation manual A SANITATION AND CLEANING PROCEDURES NWARNIN To prevent electrical shock hazard the main power switch must be in the down or off O position before cleaning the Activator 1 Because the top surface remains relatively cool soil on the top of the Activator will not cook onto the top resulting in a quick and easy cleanup 2 Heat on Demand Activator should be cleaned and sanitized after each day s use or as necessary by the following meth
19. rtain environmental conditions can affect the life of your bases Performance and aesthetics are a function of the condition of the bases These bases are designed to function optimally when used in accordance with these instructions The following explanations can help you get the longest service from your bases As with any piece of equipment the better it is taken care of the greater the expected usefulness A WAREWASHING There is a right way to warewash your bases to assure extended usefulness Send the bases through the warewashing process at an angle of 60 to 80 degrees Avoid inappropriate detergent formulations Through experience and testing Aladdin has determined that detergents with very high chlorine levels clean the bases more effectively The high level of chlorine will not damage the product and will assist in the prevention of stain build up The proper rinse aid will minimize water spotting and will improve the drying process Water temperatures in wash and final rinse cycles need to be closely controlled Wash temperature range should be 150 F minimum while the final rinse range should be 180 190 F maximum In semiautomatic automatic rack type dish machines the bases will have to be racked If an ample number of racks are available the bases can be allowed to stand for a few minutes in the rack after emerging from the machine This will allow for better drying B PREMATURE FAILURE The bases are designed and manuf
20. ther person or by custom or practice CALL ALADDIN TOLL FREE AT 1 800 888 5426 IF YOU HAVE ANY QUESTIONS ABOUT THIS WARRANTY OR YOUR ATR PRODUCT Org 12 95 Rev 08 99 19
21. urned Off o and is disconnected from the electrical supply NOTE Fasteners used in the Activator are metric Any attempt to replace metric fasteners with English fasteners could result in stripped threads or improperly affixed components Electrical parts illustrated on the parts illustration wiring schematic and parts list are for purposes of Illustration only Only the parts listed on page 15 are replaceable in the field by a qualified electrician All other service work will require that the Activator be returned to the Aladdin factory for service Should the Activator have to be returned for service to the Aladdin factory contact the Aladdin Temp Rite Service Department to make arrangements for a loaner or maintenance float Activator ELECTRICIAN S TROUBLESHOOTING GUIDE MALFUNCTION CAUSE SOLUTION 1 No Power Indicator Light Main Power switch is off Turn on main power switch Improper electrical plug connection Insert and twist plug correctly Check receptacle Power outage Call Facilities Maintenance Burned out light bulb Check bulb and replace assembly 2 Base does not start to heat No Incorrectly positioned base Position base snugly against alignment blinking yellow light but red fixture so that switch is fully depressed power light is on Base does not finis g Tncorrectly positioned base Remove original base and correctly reposition No green light a new base in alignment fixture Do not double cycle the same base
22. x p gt E sTo LIA s 20 5 67 NC RED ames SN SHIELDED CABLE 34 BB SS TT ET M ABER COLOR GEN GREEN war wHITE 1 ERN BROWN vEL BLU T BLUE PUR pet oe NOTES ibeere LTVIST WIRES WHERE POSSIBLE lt HOT N L1 L2 L3 ain 2 SERVICE SPECIFICATIONS 120 208VAC 20AMP 3PHASE 6OHZ Electrical parts illustrated on the parts illustration wiring schematic and parts list are for purposes of illustration only Only the parts listed on page 15 are replaceable in the field by a qualified electrician All other service work will require that the Activator be returned to the Aladdin Temp Rite factory for service Should the Activator have to be returned for service to the Aladdin Temp Rite factory contact the Aladdin Temp Rite Service Department to make arrangements for a loaner or maintenance float Activator 16 BASE CARE amp HANDLING INSTRUCTIONS To prevent damage bases should be activated HEATED only by Aladdin IHA 96 Activator Do not microwave Do not place in any type of oven or heat source Do not stack bases after activating 7 WARNING Aladdin recommends that these bases not be immersed in liquids for longer than 15 minutes HEAT ON DEMAND BASE CARE AND HANDLING INTRODUCTION Ce
23. y and Health Administration IHA 96 HEAT ON DEMAND ACTIVATOR This equipment generates uses and can emit radio frequency energy and if not installed and used in accordance with these instructions may cause harmful interference to radio communications devices Changes or modifications to this equipment not expressly approved by the party responsible for compliance could void the user s authority to operate this equipment There is no guarantee however that interference will not occur in a particular installation Ifthis equipment is found to cause harmful interference to radio communications the user is encouraged to correct the interference by one or more of the following means A Reorient or relocate the receiving antenna B Increase the separation between the equipment and the receiver C Connect the equipment into an outlet or on a circuit different from that which the receiver is installed D Consult your sales representative Aladdin Temp Rite Service Department or an experienced radio TV technician NOTE Each user is responsible for adherence to existing local codes regarding the posting of warning notices V RECEIVING amp INSPECTING THE EQUIPMENT Even though this equipment is carefully packaged care should be taken during unloading so the equipment is not damaged Carefully check for any visible signs of damage to the carton If evidence of damage exists the carton should be opened immediately and a
Download Pdf Manuals
Related Search