Built-in Dishwasher SERVICE MANUAL
Contents
1. a separate circuit If direct wiring dishwasher Use flexible armored or non metallic sheathed copper wire with grounding wire that meets the wiring requirements for your home and local codes and ordinances Use strain relief method provided with house wiring junction box or install a U L listed CSA certified clamp connector to the house wiring junction box If using conduit use a U L listed CSA certified conduit connector If connecting dishwasher with a power supply cord Use a ULL listed 16 gauge three conductor power supply cord that meets all local codes and ordinances Maximum length of the power supply cord is 6 feet 1 8m a clamp connector to fit a 7 8 2 2cm diameter hole is required to secure power supply cord to dishwasher terminal box Power supply cord must plug into a mating three prong grounded outlet located in the cabinet next to the dishwasher opening Outlet must meet all local codes and ordinances Water You must have a hot water line with 20 120 PSI 138 862 KPa water pressure 120 F 49 C water at dishwasher 3 8 0 D tubing with compression fitting or flexible stainless steel braided fill line 1 2 minimum plastic tubing is optional but not recommended a 90 elbow with 3 8 N P T external pipe threads on one end Do not solder within 6 15 2cm from water inlet valve Page 8 48 Serial Number Version 00 00 Edition Nov 23 20052. Haier Built in Dishwasher SERVICE MANUAL Models ESD400 ESD401 ESD402 Features Energy Star for energy consumption of USA rules Stainless steel Interior tub Electronic control Triple level filter system Three spraying higher cleaning ratio The capacity for 12 place settings Soil sensor Part DW 8888 26 Serial Number Version 00 00 Edition Nov 23 2005 Haier Built In Dishwasher Model ESD400 ESD401 ESD402 Page 1 48 Serial Number Version 00 00 Edition Nov 23 2005 Haier Built In Dishwasher Model ESD400 ESD401 ESD402 Contents 1 Product Code Illumination and Series Introduction ccccccccseeeeeeeeeeeeeeeseeeseeeeeeaeeeeeeess 2 2 Foar O oean EE E A E EE E 2 SIde F KO CAUIM OM erst charset tent aa a e iene eens 4 4 Net dimensions A dae nan ty adden deen eh ee aes 5 DIA allao ietediasaaetean circa eneaats ips decsnragtnansane ns start antl Seats si sad on same sates A es 5 Oo AnlS ANG Feature Sasin ue deeds N eee wdesniaeteetees 25 Foes 6 6 i gee g ee arte mrt ne ete at URC eon ger ee oe ee nee Ter 25 a NOS Sareea tastes coe Sac acgeat arma aaccucedscoraeeosceadacte conc satecttsanere socasamen ee oae ee can cee ceneeee 26 ODISHWESME LO AGING enrarir ee E 26 tO Dishwasher A SO sree ciate tet tease clear ented esta cence ere iat eee te deca cea 30 Til VVASFINIG SyS TON esc isae bench ease tesco ehh ee eek aa bec aout ee Creme okie ate 36 TTADMIN SYSTEM ceri suteaseteianstietetatdcdyneda
3. If you are going the attach the dishwasher to the sides of the cabinet follow steps 6 through 12 Model ESD400 ESD401 ESD402 Page 17 48 Serial Number Version 00 00 Edition Nov 23 2005 Haier Built In Dishwasher Model ESD400 ESD401 ESD402 lf the minimum cutout height is less than 24 86 4 cm he adjust legs can be removed for additional clearance This will allow the dishwasher to fit into a 33 45 85 9 em high cutout but the dishwasher will be more difficult to move into position tf the wheels are removed protect the floor when moving the dishwasher ELPFUL TIP Built up floors Measure height of opening from underside of countertop to built up floor If the height is at least 33 3 4 84 Som the dishwasher will fit into the opening without modification to the countertop or flooring Put wheels L in position 1 and tum the front lewa er legs up all the way Add shims as needed in the area shown to bring dishwasher Up to proper height Note Shims must be securely attached to floor to prevent their movement when the dishwasher is operated stand dishwasher upright The dishwasher must be secured to the cabinet There are two brackets on top of the dishwasher that usually can be attached to the countertop this is not possible the brack ets M may be moved to the sides of the dishwasher Ifyou are going to attach the dishwasher to the countertop skip to step 13 If you are going the attach the dishwashe
4. Sterling Silver or Yes Silver Plate Run a rinse cycle if not washing Immediately Prolonged contact with food containing salt acid or sulfide eggs mayonnaise and seafood can damage finish Tin NiO Can rust Wooden Ware No Wash by hand Always Check Manufacturer s instructions before Washing Untreated wood can warp crack or lose its finish DISHWASHER CARE Cleaning Cleaning the exterior In most cases regular use of a soft damp cloth or sponge and a mild detergent is all that is necessary to keep the outside of your dishwasher looking nice and clean Cleaning the interior Hard water minerals can cause a white film to Build up on the inside surfaces es peqally just beneath the door area Do net clean the dishwasher interior until it has cooled Wear rubber gloves Do not use any type of cleanser other than dishwasher detergent because it may cause foaming or sudsing Page 38 48 Serial Number Version 00 00 Edition Nov 23 2005 Haier Built In Dishwasher Model ESD400 ESD401 ESD402 Make a paste with powdered dishwasher detergent on a damp sponge and clean OR Use liquid automatic dishwasher detergent and clean with a damp sponge OR See the vinegar rinse procedure in spotting and filming on dishes in Troubleshooting NOTE Run a Normal cycle with detergent after cleaning the interior 15 Drain Air Gap Check the drain air gap anytime your dishwasher isn t draining well Some state
5. ire Renal ning Your dishwasher starts a 2 minutes drain if needed Let the dishwasher drain completely The light turns off after 2 minutes NOTE If your dishwasher does not need draining press CANCEL Drain again the light turns off Select a new cycle and options To stop the drain You can press CANCEL again to stop the drain immediately Remember to drain the dishwasher before starting a new cycle 10 6 Changing a cycle During the first fill of a cycle 1 Press a new cycle and or options Check the detergent dispensers They must be filled properly for the new cycle After the first fill of a cycle Press 7 cancel Teni If your dishwasher has a dual digit display it shows Time Remaining Your dishwasher starts a 2 minutes drain tif needed Let the dishwasher drain completely The light turns off after 2 minutes NOTE If your dishwasher does not need draining press CANCEL againthe light turns off 1 Check the detergent dispensers They must be filled property for the new cycle 2 Press a new cycle and or options 10 6 Adding Items During a Cycle Page 34 48 Serial Number Version 00 00 Edition Nov 23 2005 Haier Built In Dishwasher Model ESD400 ESD401 ESD402 You can add an item anytime before the main wash starts Open the door and check the detergent dispenser If the cover is still closed you can add items TO add items 1 Carefully open the door slightly to stop the cycle Wait for t
6. Circuit Diagram 120V 60HZ Edition Nov 23 2005 Model ESD400 ESD401 ESD402 Door switch A aaa BK es BK Ww Ww JAK Ground Door switch X ee a W W Ww P2 6 J Contorl board P1 ee Display Temperature limiter Heater O R O AN Z m Ww P6 OR A V f W ax motor P10 7 Y A AE A A BU W P9 v BU SS Z W ashing motor LZ T NG Pie ne ee PK f vA REI bN BU moo gt gt EN ra Capacitor P P4 lt K Drain motor B q P3 lay Gy OR Y l B Dispenser o m reel E a Float switch A Inlet valve pa k p2 3 BU E a ee a D Rinse Aid Sensor Le R pa 1 LY y p BU Thermostat P2 2 R by 0 R l P7 W W l Soil sensor P12 1 R id P12 2 W Bf lt P2 3 BU 5V Page 47 48 Serial Number Version 00 00 Edition Nov 23 2005 Haier Built In Dishwasher Model ESD400 ESD401 ESD402 Sincere Forever Page 48 48
7. Dao not kink o pinch cropper tubing drain hose power sup ply cord or direct wire between dishwasher and cabinet Center dishwasher in opening HELPFUL TIP Built up floors Tilt dishwasher backward to move into opening Once in position support front of dishwasher by lowering or shimming front feet Page 19 48 Serial Number Haier 18 20 Built In Dishwasher Version 00 00 Edition Nov 23 2005 Remove cardboard from under dishwasher HELPFUL TIP lt is okay if dishwasher fits tightly into cabinet opening Do not remove insula tion blanket it reduces the sound level Align front of dishwasher door panel Y with cabinet doors Z You may need to adjust alignment to look good with your cabinets HELPFUL TIP Prop up one side of frame te hold dishwasher up off floor when adjusting front legs Check that leveling legs AA are firmly against the floor Close and latch the door and place level against the front panel EB Check that dishwasher is plumb Adjust level ing leg o add shims under rear wheel until dishwasher is level Note Shims must be securely attached to floor to pre vent their movement when the dishwasher is operated Re peat for other side of dishwasher NOTE Shims must be securely attached to floor to prevent heir movement when the dishwasher is operated Repeat for other side of dishwasher Place level against top front opening of tub CC Check that dishwasher
8. and gentle dry Use main During the heated dry detergent China Crystal the heating element dispenser section On some models cycles on and off Final Minimum Water Heated Timeimin Usage Rinse igqal Li ve prior to entertaining Use main The sensor adds water detergent and time to the cycle if dispenser needed for maximum section cleaning This cycle uses a shortened dry time Towel drying may be needed Pre Main Rinse Final an Minimum Water wash Wash Heated Timeimin Usage Rinse igal L Use this cycle fora quick wash and light dry to cleanup cookware O Quick Wash Use this rinse cycle O for rinsing dishes glasses and silverware that will not Do not use be washed right a 7 paka J detergent with Rinse amp Hold away this cycle Main Final Time Wash Heated imin Rinse Ifthe incoming water temperature is less than the recommended temperature or food soils are heavy the cycle will automatically compensate by adding time heat and water as needed ENOTE The sensor in your dishwasher monitors the soil level Cycle time and or water usage can vary from the numbers above as the sensor adjusts the cycle for the best wash performance Page 33 48 Serial Number Version 00 00 Edition Nov 23 2005 Haier Built In Dishwasher Model ESD400 ESD401 ESD402 10 5 Canceling a cycle Anytime during 4 cycle press tama Tein If your dishwasher has a dual digiplay it shows
9. cover latch 3 Add rinse aid until the indicator window looks full 4 Clean up any spilled rinse aid with a damp cloth 5 Close the cover Rinse aid setting The amount of rinse aid released into the final wash can be adjusted The factory setting is at 3 For most water conditions Set the adjuster to 2 or 3 If there are rings or calcium hard water spots on dishes try a higher setting To adjust the setting Open the dispenser cover Turn the adjuster inside the dispenser to the desired setting 10 4 Cycle Selection Charts Page 31 48 Serial Number Version 00 00 Edition Nov 23 2005 Haier Built In Dishwasher Model ESD400 ESD401 ESD402 Select the wash cycle and options desired The dishwasher starts filling once you press cycle unless you select a delay wash You can select an option as the machine ts filling A e shows what steps are in each cycle Temperatures indicate where extra heat is added Water usage is shown in U S gallons liters This model meets the ENERGY STAR guidelines for energy efficiency Cycle time includes dry time An asterisk by the cycle time indicates the cycle time might be longer depending on the temperature of the water entering the dishwasher a Lise this cycle for all day to day soil types Gaal including both normal and heavy soils giving Use both Ant Bacterial YOU exceptional cleaning performance T tabla Pere combined with p On some models reassuri
10. front levaler legs to the same height Min Wheel poston Number of turns cutout height see illustration on front leg a4 86 4 cm gaia em a d E a ee a 34 112 87 6 cm Page 16 48 Serial Number Haier Built In Dishwasher Version 00 00 Edition Nov 23 2005 lf the minimum cutout height is less than 24 86 4 cm the adjust legs can be remowed for additional clearance This will allow the dishwasher to fit into a 33 4 5 85 9 cm high cutout but the dishwasher will be more difficult to move into position tf the wheels are removed protect the floor when moving the dishwasher HELPFUL TIP Built up floors Measure height of opening from underside of countertop to built up floor If the height is at least 33 3 4 84 Semi the dishwasher will fit into the opening without modification to the countertop er flooring Put wheels L in position 1 and tum the front leveler legs Up all the way Add shims as needed in the area shown to bring dishwasher Up to proper height Note Shims must be securay attached to floor to prevent their movement when the dishwasher is operated stand dishwasher upright The dishwasher must be secured to the cabinet There are two brackets on top of the dishwasher that usually can be attached to the countertop lf this is not possible the brack ets M may be moved to the sides of the dishwasher Ifyou are going to attach the dishwasher to the countertop skip to step 13
11. or local plumbing codes require the addition of a drain air gap between a built in dishwasher and the home drain system If a drain is clogged the drain air gap protects your dishwasher from water backing up into it The drain air gap is usually located on top of the sink or countertop near the dishwasher NOTE The drain air gap is an external plumbing device that is not part of your dishwasher The warranty provided with your dishwasher does not cover service costs directly associated with the cleaning or repair of the external drain air gap TO clean the drain air gap Clean the drain air gap periodically to ensure proper drainage of your dishwasher Follow the cleaning instructions provided by the manufacturer With most types you lift off the chrome cover Unscrew the plastic cap Then check for any soil buildup Clean if necessary 16 Storing Storing for the Summer Protect your dishwasher during the summer months by turning off the water supply and power supply to the dishwasher Winterizing your dishwasher Protect your dishwasher and home against water damage due to freezing water lines If your dishwasher is left in a seasonal dwelling or could be exposed to near freezing temperatures have your dishwasher winterized by authorized service personnel Page 39 48 Serial Number Version 00 00 Edition Nov 23 2005 Haier Built In Dishwasher Model ESD400 ESD401 ESD402 17 Function Schedule 1 Anti Bacterial wash Heavy soil Th
12. Haier Built In Dishwasher Model ESD400 ESD401 ESD402 Drain You must a Use the new drain hose supplied with your dishwasher If this is not suitable use a new drain hose with a maximum length of 12 feet 3 7 m that meets all current AHAM IAPMO test standards is resistant to heat and detergent and fits the drain connector on your dishwasher have a high drain loop 20 inches 50 8cm above the subfloor or floor connect drain hose to waste tee or disposer inlet above drain trap in house plumbing and 20 inches 50 8cm minimum above the floor use an air gap if the drain hose is connected to house plumbing lower than 20 inches 50 8cm above subfloor or floor use 1 2 minimum D drain line fittings Measured from the lowest point on the underside of countertop May be reduced to 33 7 8 86cm by removing wheels from dishwasher Minimum measured from narrowest point of opening Maybe increased to 6 7 8 17 5cm if height of opening is 34 1 2 87 6cm at lowest point Cut openings in shaded area of cabinet walls or floor as specified in chart OPENING FOR DIANETER directwie e P ORRERI 14127 3 8ern Page 9 48 Serial Number Version 00 00 Edition Nov 23 2005 Haier Built In Dishwasher Model ESD400 ESD401 ESD402 A PN Electrical Shock Hazard Disconnect electrical power at the fuse box or cir cuit breaker box before installing dishwasher Failure to do so can result
13. amage may occur Load plastic items in the top rack only Only plastic items marked dishwasher safe are recommended Load plastic items so the force of the spray does not move them during the cycle To avoid chipping do not let stemware touch other items Small bowls pans and other utensils can be placed in the top rack Load bowls in the center section for best stability Utility shelf Fold down the extra shelf on the left or right side of the top rack to hold additional cups stemware or long items such as utensils and spatulas Adjustable 2 position top rack You can raise or lower the top rack to fit tall items in either the top or bottom rack Raise the top rack to accommodate items up to 7 1 in 18 cm in the top rack and 12 2 in 81cm in the bottom rack or lower the top rack to accommodate items up to 9 in 23 cm in the top rack and 10 2in 26cm bottom racks Adjusters are located on each side of the top rack To remove the top rack 1 Pull the rack forward slightly to access track stops Page 28 48 Serial Number Version 00 00 Edition Nov 23 2005 Haier Built In Dishwasher Model ESD400 ESD401 ESD402 2 To release press the button of the track stop and pull track stop out of the track 3 After removing both track stops pull rack out To replace the top rack 1 Place the rollers on each side of the rack into the rack tracks and push the rack back 2 Insert track stop into rack 3 Pull
14. anytime during the delay countdown After adding items close the door firmly until it latches The delay countdown will not continue if the door is not latched You can delay the start of a cycle up to 12 hours The first time you use Delay Start you will see showing a 1 hour delay Page 35 48 Serial Number Version 00 00 Edition Nov 23 2005 Haier Built In Dishwasher Model ESD400 ESD401 ESD402 After the first time that you use delay the control will start by calling up the last delay that you can You can adjust from there if you want to change it To delay the start 1 Close the door 2 Repeatedly press until you see the desired hours of delay in the display When the delay reaches 12 hours the delay turns off Press Delay Start again to select a new number of delay hours 3 Select a wash cycle and options NOTE To cancel the delay and cycle press Cancel To cancel the delay and start the cycle immediately press Delay Start until no hours show in the display Plate Warmer Use the Plate Warmer option to warm serving dishes or dinner plates Note Do not use the option with cycles 1 Open the door 2 Press plate warmer button plate warmer glows 3 Allow 8 minutes to heated the dishware 10 7 Cycles Status Indicators Follow the progress of your dishwasher with the Cycle Status indicators Water Heated on ESD310 311 312 models Water Heated glows only when the cycle pauses to heat water to a set temperature Was
15. ccsdadodwe do picytaaatie Quvaatnawt tite tade nado mutedalsuneuuaietdoasidites 36 13 OVEN Protection Float scutaioetivectctvnelstedievetetidnesisadaldesbielobentspaetdaualssedlieelebibiedaabeleeabls 36 14 Washing special items and dishwasher CaLe ccccceeeeeeeeeeeeeeeeeeeeeeaneeeeeeeeseaeeeeeesaaees 37 W 2 2 ales a 8 yeepeneeee errant nr eran sree haere ence eta tr ree Ne Ree ent ist th eet arte erent eer S 38 1G SHO FING scenes teas Aacaaetactassceanntdecsseanoncasiedtasannese dense acendasuaescasaniedace teanenteieceranceeedenaonenladanccuse 38 A 72 CHONG ONG aaeianats oteotel aches dase e Jat aera N 39 18 Maintenances Services and Trouble Shooting cccccsseseeeeecesseeeeeceaeeeeeeeeeeaeeeesesaaeees 41 Tee FFG CINE eA AI eo tei ssas ste rete chances diner tadatad tee Sacetenteat ln oes arse aca cred netisuadleside ube inddetle nena 46 Page 2 48 Serial Number Version 00 00 Edition Nov 23 2005 Haier Built In Dishwasher Model ESD400 ESD401 ESD402 1 Product Code Illumination and Series Introduction Model Identification ESD UU C A B C A Energy Star Dishwasher B Series of factory design C Code of Color 0 White 1 Black 2 Stainless steel Examples ESD400 It represents energy star dishwasher of 400 series the color of appearance is white ESD401 It represents energy star dishwasher of 400 series the color of appearance is black ESD402 lt represents energy star dishwasher of 400 series t
16. ches 7 6 cmijand check that space s between inner door and tub is equal on both sides If spacing is not equal loosen bracket screws and shift tub Tighten bracket screws If secunng to sides of cabinet replace the plastic buttons G Check that top of door does not contact screws brackets or countertop If it does dishwasher must be lowered and re leveled Remove paper or towel from dishwasher Page 24 48 Serial Number Version 00 00 Edition Nov 23 2005 Haier Built In Dishwasher Model ESD400 ESD401 ESD402 Secure Dishwasher A WARNING Tip Over Hazard Do not use dishwasher until completely installed Do not push down on open door Doing so can result in serious injury or cuts pen dishwasher door and place towel A over pump as sembly and spray arm of dishwasher This will prevent screws from falling Into pump area when securing dishwasher to countertop Check that dishwasher is still level and centered in the opening Hn E _ sx secure dishwasher to countertop with two No ST4 2 x18 B Phillips head screws B The dishwasher MUST be secured all to keep it from tipping when door is opened Do Not drop i li srews into bottom of dishwasher 4 Open door about 3 inches 7 6 cmijand check that space s between inner door and tub is equal on both sides If spacing is not equal loosen bracket screws and shift tub Tighten bracket screws If secunng to sides of cabinet replac
17. ck for leaks Drain Connection To help minimize vibration noise route drain hose to avoid contact with motor door springs water line cabinet floonng or the edge ofthe hole where it passes through the cabinet Do not remove drain loop N from side of dishwasher 8 Place the smaller drain hose damp N onto the small end of the drain hose O Remove the plug from the ba a connector P 9 Push the drain hose into the connector P up to the rib O on the drain hose a a a Use pliers to open clamp N and slide clamp onto connec 10 tor F between nbs O on connector Jd Page 23 48 Serial Number Version 00 00 Edition Nov 23 2005 Haier Built In Dishwasher Model ESD400 ESD401 ESD402 Secure Dishwasher A WARNING Tip Over Hazard Do not use dishwasher until completely installed Do not push down on open door Doing so can result in serious injury or cuts pen dishwasher door and place towel A over pump as sembly and spray arm of dishwasher This will prevent screws from falling Into pump area when securing dishwasher to countertop Check that dishwasher is still level and centered in the opening Hn E _ sx secure dishwasher to countertop with two No ST4 2 x18 B Phillips head screws B The dishwasher MUST be secured all to keep it from tipping when door is opened Do Not drop i li srews into bottom of dishwasher 4 Open door about 3 in
18. cting Hi Temp Wash If user select Sanitize Rinse option the dishwasher would heat water to 161F in this step 6 Normal Wash Light soil level Pre wash warmly 130F Main wash gt Final Rinse gt Drvina lf heated drv is selected Notice The temp should 140 F when selecting Hi Temp Wash If user select Sanitize Rinse option the dishwasher would heat water to 161F in this step 7 China Crystyle Wash Pre wash warmly 130F Main wash gt Final Rinse gt Drvina lf heated drv is selected 10 Speed Wash 120F Main wash 11 Rinse amp Hold Rinse only 12 Plate Warmer Page 41 48 Serial Number Version 00 00 Edition Nov 23 2005 Haier Built In Dishwasher Model ESD400 ESD401 ESD402 18 Maintenances Services and Trouble Shooting J L5 O OL7 OL8 OL9 OL10 L02 KD Ke K3 kA K ke koi K7 ke ko Kioo Ko2 N Nees LY ey Ae NF SE ee SY eA Nee VEN G7 rout S1 S2 S3 S4 S5 S6 S7 S8 L i O E S E O Tni If the 2 digit 7 segment displayer display Er it shown that the temperature sensor is fault Page 42 48 Serial Number Version 00 00 Edition Nov 23 2005 Haier Built In Dishwasher Model ESD400 ESD401 ESD402 Analysis of the common breakdowns Phenomenon the cycle and option can not been selected Is the door closed N Close the door Y Do you put the plug if N gt Put the plug into the outlet installed into the outlet Is the po
19. detergent NOTE Use both sections for cycles with 2 washes Use only the main wash section for cycles with 1 wash See the Cycle Selection Charts for more details How much detergent to use Different brands of dishwasher detergent have different amounts of phosphorous for softening water If you have hard water and use a detergent with a phosphorous content of less than 8 7 you might need to use more detergent or use a detergent with a phosphorous content higher than 8 7 The amount of detergent to use depends on the hardness of your water and the type of detergent If you use too little dishes won t be clean If you use too much in soft water glassware will etch 10 3 Rinse Aid dispenser Rinse aids prevent water from forming droplets that can dry as spots or streaks They also improve drying by allowing water to drain off of the dishes during the final rinse by releasing a small amount of the rinse aid into the rinse water Your dishwasher is designed to use a liquid rinse aid Do not use a solid or bartype Filling the dispenser The rinse aid dispenser holds 4 8 0z 145ml of rinse aid Under normal conditions this will last for about three months Rinse aid is released through an opening in the dispenser You do not to wait until the dispenser is empty to refilled it Try to keep it full but be careful not to overfill it 1 Make sure the dishwasher door is fully open 2 Open the dispenser by pushing the
20. e Cut a 1 1 2 3 8cm diameter hole in cabinet wall or foor onthe side of the opening dosest to the sink Connect drain hose to waste tee or waste disposer follow ing one method 11 a ad oto anairgap Tt noairgap te no waste disposer re OO a anair gap is recommended Waste disposer air gap 1 Remove the disposer knockout plug Cut end of drain hose I if needed ido not cut ribbed section 2 Attach drain hose to air gap J with large spring type clamp K If the drain hose was cut use a 1 1 2 to 2 3 8 to 5cm screw type clamp 3 Use a rubber hose connector L with spring or Screw type clamgs M to connect air gap to disposer inlet W This connection N MUST be before drain trap 0 and at least 20 50 8cm above the floor where dishwasher will be installed Go to step 12 No waste disposer air gap 1 Cut end ofdrain hese Tif needed do not cut ribbed section 2 Attach drain hose to air gap J with lange spring type clamp Ifthe drain hose was cut use a 1 1 2 to 2 3 8 lo 5 om screw type damp 3 Use a rubber hose connector L with spring or screw wpe damps M to connect air gap to waste tee P This connection P MUST be before drain trap O and above the floor at 15 4 5 40cmito 39 2 5 1 00cm at least 20 50 8 cm above the floor where dishwasher will be in Stalled so to step 12 Page 13 48 Serial Number Vers
21. e must ex tend to the lett front of cabinet opening Go to step 6 Power supply cord method Cut a 1 1 2 3 80m hole Din left hand cabinet rear or side C iption allocations are shown Wood cabinet Sand hole until smooth Aa Install a mating three proung grounding type wall recep tacle Ein the cabinet next to the dishwasher opening So p to step 6 oy Page 11 48 Serial Number Version 00 00 Edition Nov 23 2005 Haier Built In Dishwasher Model ESD400 ESD401 ESD402 Water line HELPFUL TIP Routing the water line through the left side of cabinet opening will make water connection easier Cut a 162741 3 em minimum hole F in left hand cabinet side rear or floor Optional locations are shown The hale F is about 1 46 higher than hole C or hole D T Measure overall length of copper tubing G required At tach copper tubing to water line with manul shutoff valve Carefully feed copper tubing through hoe in cabinet copper tubing will bend and kink easily until it is far enough into he cabinet opening to connect it to dishwasher inlet on the fount left of dishwasher Turn shutoff valve H to ON position Flush water into a bucket to get rid of particales that may clog the inlet vake 9 Turn shutoff valve to OFF position Page 12 48 Serial Number Version 00 00 Edition Nov 23 2005 Haier Built In Dishwasher Model ESD400 ESD401 ESD402 Drain hos
22. e the plastic buttons G Check that top of door does not contact screws brackets or countertop If it does dishwasher must be lowered and re leveled Remove paper or towel from dishwasher Page 25 48 Serial Number Version 00 00 Edition Nov 23 2005 Haier Built In Dishwasher Model ESD400 ESD401 ESD402 6 PARTS AND FEATURES j 7 pe 9 2 3 10 12 an 5 11 NE 13 h 1 Upper spray 8 Adjustable Top rack 2 Upper rack track 9 Middle spray arm 3 Water inlet opening in tub wall 10 Silverware basket 4 Spray arm 11 Overfill protection float 5 Bottom rack 2 Heating element 6 Vent system 13 Detergent dispenser T Utility shelf twoa 7 Control Panel 000 Ha Tega Wah yamm aak Page 26 48 Serial Number Version 00 00 Edition Nov 23 2005 Haier Built In Dishwasher Model ESD400 ESD401 ESD402 8 START UPGUIDE Before using your dishwasher remove all packaging materials Using New Dishwasher 1 Rinse aid is essential for good drying Be sure to fill the dispenser before you use your new dishwasher Each filling will last about 1 to 3 months depending on your usage 2 Scrape large food soil and hard items toothpicks or bones from dishes You do not need to pre rinse your dishes 3 Properly load the dishwasher See Dishwasher Loading Load dishes with space in between so water will reach the soiled surfaces Make sure nothing prevents the spray arm s from sp
23. ere with the spray arm rotation Conserve water energy and save time over hand rinsing by running a rinse cycle to keep dishes moist if you do not plan to wash them soon Foods such as eggs rice pasta spinach and cooked cereals may be hard to remove if they are left to dry over a period of time Quiet operating tips To avoid thumping clattering noises during operation Make sure lightweight load items are secured in the racks Make sure pot lids and handles pizza pans cookie sheets etc do not touch interior walls or interfere with the rotation of the spray arm Load dishes so they do not touch one another NOTE For built in models keep sink drain plugs closed during dishwasher operation to prevent noise transfer through drains 9 1 Loading Top Rack The top rack is designed for cups glasses and smaller items Many items up to 9 K we i ieee i i l 1 e ca a Te j S in 22 cm fit in the top rack See recommended loading patterns shown NOTE The features on your dishwasher rack may vary from the drawings shown Place items so open ends face down for cleaning and draining Load glasses and cups in top rack only The bottom rack is not designed for glasses and cups Damage can occur Place cups and glasses in the rows between tines Placing them over the tines can lead to breakage and water spots China crystal and other delicate items must not touch each other during dishwasher operation D
24. grounded cord connected dishwasher The dishwasher must be grounded In the event of a malfunction or breakdown grounding will reduce the risk of electric shock by providing a path of least resistance for electric current The dishwasher is equipped with a cord having an equipment grounding conductor and a grounding plug The plug must be plugged into an appropriate outlet that is installed and grounded in accordance with all local codes and ordinances WARNING Improper connection of the equipment grounding conductor can result ina risk of electric shock Check with a qualified electrician or service representative if you are in doubt whether the dishwasher is properly grounded Do not modify the plug provided with the dishwasher if it will not fit the outlet have a proper outlet installed by a qualified electrician For a permanently connected dishwasher The dishwasher must be connected to a grounded metal permanent wiring system or an equipment grounding conductor must be run with the circuit conductors and connected to the equipment grounding terminal or lead on the dishwasher SAVE THESE INSTRUCTIONS Tip Over Hazard Do not use dishwasher until completely installed Do not push down on open door Doing so can result in serious injury or cuts A WARNING 4 Electrical Shock Hazard Electrically ground dishwasher Connect ground wire to green ground connector in terminal box Do not use an extension cord Fail
25. he color of appearance is stainless steel 2 Features 2 1 Energy Star for energy consumption of USA rules 2 2 Stainless steel Interior tub 2 3 Electronic control 2 4 Triple level filter system 2 5 Three spraying higher cleaning ratio 2 6 The capacity for 12 place settings 2 Soil sensor Page 3 48 Serial Number Version 00 00 Edition Nov 23 2005 Haier Built In Dishwasher Model ESD400 ESD401 ESD402 3 Safety Precaution DISHWASHER SAFETY Your safety and the safety of others are very important We have provided many important safety messages inthis manual and on your appliance Always read and obey all safety messages This is the safety alert symboal This symbol alerts you to potential hazards that can kill or hurt you and others All safety messages will follow the safety alert symbol and either the word DANCER or WARNING These words mean You can be killed or seriously injured if you don t rey DAWN GE R immediately follow instructions You can be killed or seriously injured if you don t WARNI NG follow instructions All safety messages will tell you what the potential hazard is tall you how to reduce the chance of injury and tell you what can happen ifthe instructions are not followed IMPORTANT SAFETY INSTRUCTIONS WARNING When using the dishwasher follow basic precautions including the following Read all instructions before using the dishwasher m Do not operate the dishwasher unless all encl
26. he spraying action to stop before opening the door 2 Open the door If the detergent dispenser cover is still closed add the item 3 Close the door firmly until it latches The dishwasher resumes the cycle after about a 10 seconds pause 10 7 Option Selections You can customize your cycles by pressing an option If you change your mind press the option again to turn the option off Select a different option if desired You cancel change an option anytime before selected option begins For example you can press an unheated drying option anytime before drying begins Hi Temp Wash Select this option to heat the water during parts of the cycle Higher water temperatures helps clean tough soils Hi Temp Wash with the Pots amp Pans Normal raises the water temperature in the main wash This option adds heat water and wash time to a cycle NOTE Hi Temp Wash is an option with the Pots amp Pans and Normal cycles Always use Hi Temp Wash if you have hard water You can t change this option after the first filling NOTE Anti bacteria Wash automatically uses this option Sanitize Rinse is an option with the Pots amp Pans Normal cycle Only these sanitization cycles have been designed to meet the NSF ANSI requirements You can t change this option after the main wash complete If you change this option the remaining time displayed by LED will reduce add 3 minutes Heated Dry Select this option to dry dishes with heat The dishes take longer
27. hing or rinsing continues as water heated Once water reaches the set temperature the light goes off and the cycle resumes Washing on ESD310 311 312 models Washing glows during prewash and main wash periods Turbidity Sensor on ESD310 311 312 models Turbidity Sensor glows during the sensing part of the cycle Your dishwasher sense soil lever at the end of the Pre Wash Washing continues while Sensing occurs Rinsing on ESD310 311 312 models Rinsing glows during rinse periods Drying on ESD310 311 312 models Drying glows when the dishwasher is drying after the final rinse Clean Clean glows when a wash cycle is complete The light will remain ON until door is opened Sanitized Sanitized glows when cycle has met sanitization condition The light will remain ON until door is opened Add Rinse Aid on ESD310 311 312 models Fill the Rinse Aid dispenser when Add Rinse Aid is lit A rinse aid prevents water from forming droplets that dry as spots or streaks If the Rinse Aid dispenser is empty the light glows when you select a cycle or while a cycle is running 11 Wash System The five level wash system provides excellent cleaning results Three levels of filtration and a Soil collector system filter the wash water and prevent food Serial Number Version 00 00 Edition Nov 23 2005 Haier Built In Dishwasher Model ESD400 ESD401 ESD402 particles from redepositing on the clean dishes The wash water continuously f
28. in death or electrical shock Prepare cabinet Disconnect the power supply Turn water off Put on glowes and safety glasses lf you are replacing a dishwasher Check that the water line A reaches to the back left of opening where the water connection will be made heck that the direct line B reaches to the back left of opening where the electrical connection will b made lf the water line and the direct wire reach into the opening far enough go to step 10 page 10 lf you are installing a new dishwasher complete all of the following steps Electrical Folow all national and local codes and orndinaces for com pleting electrical supply to cabinet HELPFUL TIP Wiring the dishwasher will be easier if you route wire into the cabinet opening from the left side Page 10 48 Serial Number Version 00 00 Edition Nov 23 2005 Haier Built In Dishwasher Model ESD400 ESD401 ESD402 Direct wire method 3 Cut a WF 1 8m hole C in righthand cabinet side rear or floor Optional locations are shown Wood Cabinet Sand hole until smooth Run wire into house wiring junction box Use strain relief A method provided with junction box If no strain relief is provided install a U L listed CS4 certified clamp connec tor for flexible type wire If installing conduit attach a U L listed CsA certfied conduit connector to junction box Run other end of wire through cabinet hole Cabl
29. inning freely 4 Add detergent Always use a quality brand detergent 5 Close the door 6 Press the desired cycle and option selections The dishwasher starts filling when you press a cycle You can select options as the machine fills See Dishwasher Use 9 DISHWASHER LOADING Remove leftover food bones toothpicks and other hard items from the dishes To conserve water energy and save time it is not necessary to rinse dishes before putting them into the dishwasher The wash module removes food particles from the water The module contains a chopping device which will reduce the size of food items NOTE If hard items such as fruit seeds nuts and eggshells enter the wash module you might hear chopping grinding crunching or buzzing sounds These sounds are normal when hard items enter the module Do not let metallic items such as pot handle screws get into the wash module Damage can occur It is important for the water spray to reach all soiled surfaces Load dishes so they are not stacked or overlapping if possible For best drying water must be able to drain from all surfaces Load heavy pots and pans carefully Heavy items can dent the stainless steel interior of the door if they are dropped Page 27 48 Serial Number Version 00 00 Edition Nov 23 2005 Haier Built In Dishwasher Model ESD400 ESD401 ESD402 or bumped Make sure pot lids and handles pizza pans cookie sheets etc do not interf
30. ion 00 00 Edition Nov 23 2005 Haier Built In Dishwasher Model ESD400 ESD401 ESD402 Waste disposer no air gap 1 Remove the disposer Knockout plug Do net cut end of drain hose 2 Attach drain hose l to disposer inlet N with large spring tyre clamp K This connecting N MUST be before drain trap O and at least 20 50 8 cm abowe the foor where dishwasher will be installed So to step 12 No waste disposer air gap 1 Cut end of drain hese I ido not cut ribbed section 2 Attach drain hose to waste tee P with 1 1 2 to 2 3 8 to Som screw lype clamp M This connection P MUST be before drain trap O and at least 20 50 8 cm abowe the foor where dishwasher will be installed Go to step 12 Parts avalable trom local plumbing supply stores HELPFUL TIP To reduce the vibration of the hose keep the hose away from the floor and the edge of the hole where it passes through the cabinet Insert drain hose I into hole cutin cabinet to the back center of opening where drain connection will be made Page 14 48 Serial Number Version 00 00 Edition Nov 23 2005 Haier Built In Dishwasher Model ESD400 ESD401 ESD402 Prepare dishwasher A WARNING gt Tip Over Hazard Do not use dishwasher until completely installed Do not push down on open door Doing so can result in serious injury or cuts A WARNING Excessive Weight Hazard Use two people to move and install d
31. ird rinse 161F Sanitize Rinse Drying If heated dry is selected Notice If user selected the soak option the dishwasher would add a 4h scour amp soak rinse before the cycle start 2 Anti Bacterial wash Middle and light soil Rinse 161F Sanitize Rinse Drying if Heated dry is selected 130F Pre wash Notice If user selected the soak option the dishwasher would add a 4h scour amp soak rinse before the cycle start 3 Pots and Pans Wash Pre wash warmly 140F Main wash Drvina lf heated drv is selected Notice The temp Should 150 F when selecting Hi Temp Wash If user select Sanitize Rinse option the dishwasher would heat water to 161F in this step lf user selected the soak option the dishwasher would add a 4h scour amp soak rinse before the cycle start Notice The temp should 140 F when selecting Hi Temp Wash If user select Sanitize Rinse option the dishwasher would heat water to 161F in this step 4 Normal Wash Heavy soil level Pre wash warmly 4130F Main wash Drvina lf heated drv is selected Notice The temp Should 140 F when selecting Hi Temp Wash If user select Sanitize Rinse option the dishwasher would heat water to 161F in this step Page 40 48 Serial Number Version 00 00 Edition Nov 23 2005 Haier Built In Dishwasher Model ESD400 ESD401 ESD402 5 Normal Wash Middle soil level Drvina lf heated drv is selected Notice The temp should 140 F when sele
32. is level fram side to side If dishwasher is not level adjust front legs up or down until dishwasher is level Model ESD400 ESD401 ESD402 Page 20 48 Serial Number Version 00 00 Edition Nov 23 2005 Haier Built In Dishwasher Model ESD400 ESD401 ESD402 HELPFUL TIP SSS SE Select the proper size twist on connectors to connect your household wiring to 16 gauge dishwasher wiring 3 Insert wire ends into twist n connector Do not pre twist bare wire Twist connector Gently tug on wires to be sure both are SSE tured 2 Connect the wire B as follows using twist on connectors C sized to connect direct wire to 16 gauge dishwasher wire From bare ground wire D into a U shaped hook Wrap ground wire hook clockwise around ground connector E and under the washer F Securely tighten ground connec tor E and under the washer F Securely tighten ground connector E Do not unte knot in the wires ower supply wire Terminal box wire White gu White Black black Ground wire gt Ground connector Tighten clamp connector or conduit connector screws G Reinstall terminal box cover H with wires inside terminal box Goto step 5 The cover must be outside the box on the ight side Make sure no wires are pinched by cover Page 21 48 Serial Number Haier Version 00 00 Edition Nov 23 2005 Built In Dishwasher Model ESD400 ESD401 ESD402 Powe
33. ishwasher Failure to do so can result in back or other injury 1 a Grasp sides of dishwasher door and put dishwasher on its back Remove two screws A attaching access panel B and lower panel C7 to dishwasher using a WF hex socket nut driver or Philipis screwdriver remove panels and set panels aside on a protactive surfice Check that grounding dip Lr is attached to the lower panel Page 15 48 Serial Number Version 00 00 Edition Nov 23 2005 Haier Built In Dishwasher Model ESD400 ESD401 ESD402 Apply pipe joint compound E to Sorel bow fitting F and connect fitting to water inlet valve G Tighten elbow until snug and be sure that it faces to the rear Remove terminal box cover H Pull appliance wires I hrough hole in terminal box Do not untie the knot in the WIPES lf you are direct wiring install a U_L listed CSAscertified damp connector J to the terminal box lf using conduit use a UL isted CS4 certified conduit connector If you are installing a power supply cord kit do so now and follow kitinstructions HELPFUL TIP Put cardboard under dishwasher until it is installed opening The cardboard will help protect floor covering during installation Qoos Measure height of cabinet opening from underside of countertop to floor where dishwasher will be installed K you need the lowest point Check chart for that height opening Put wheels L in the required position Turn both
34. lows through the filter trapping food particles Two water jets located under the spray arm remove the food particles from the filter A coarse strainer prevents bones pits and other large objects from entering the pump system 12 Drying System Ps During drying you can see steam escaping through the vent at the upper left corner of the door This is normal as the heat dries f K your dishes B ee 13 Overfill Protection Float The over fill protection float in the front right corner of the dishwasher tub keeps the dishwasher from overfilling It must be in place for the dishwasher to operate Check under the float for objects that may keep the protector from moving up or down NOTE Periodically check the coarse strainer and remove any objects on the strainer IMPORTANT The vapor is hot Do not touch the vent Page 37 48 Serial Number Haier Version 00 00 Built In Dishwasher Edition Nov 23 2005 Model ESD400 ESD401 ESD402 14 Washing special items and dishwasher care WASHING SPECIAL ITEMS If you have doubts about washing a particular tem check with the manufacturer to see if it is dishwasher safe Material Aluminum Disposable Aluminum Bottles and cans Cast Iron China stoneware Crystal sold lass Ha llow Handle Knives Pewter Brass Bronze Dis posable Plastics To clean interior Dishwasher Safe Comments Yes High
35. ng sanitization cactibnk flinimum Time min 39 Light sail Lise this cycle for D hard to clean eal baked on 0 cookware and Use both F harder than normal detergent di water conditions dispenser sections Pre First Second Main Rinse Final Dry Minimum Wash Wash Wash Wash Hested Timetmin EF nse eld i O Lise this cycle for loads with normal amounts of food soil The energy usage label is based on this cycle Use both Normal detergent On models without dispenser soil sensor sections Pre Main Rinse Final Minimum Water Wash Wash Heated Timetmin Usage wi ae om Li 1308 it Llse this cycle for loads with normal amounts of food soil The energy usage label is based on this cycle Use both Normal detergent On some models dispenser with soil sensor sections Pre Main Rinse i iry Minimum Water Wash Wash i Timel min Usage i iqal L 130 zg o jenni Je Light soil E Page 32 48 Serial Number Version 00 00 Edition Nov 23 2005 al Haier Built In Dishwasher Model ESD400 ESD401 ESD402 Use this cycle for g china and crystal aS This cycle uses a light C wash and gentle dry Use main During the heated dry detergent Light the heating element dispenser section On some models cycles on and off Final Dry Minimum Water Heated Timeimin Usage Rinse igal Li lse this cycle for a china and crystal al This cycle uses a light C wash
36. omplete and Electrasol Automatic Dishwashing Detergents have been approved for use in all Haier dishwashers Keep your detergent fresh and dry Don t put powder detergent into the dispenser until you re ready to wash dishes All wash cycles except RINSE ONLY require detergent in the main and pre wash cup 10 2 Detergent Dispenser The detergent dispenser has 2 sections The small Pre Wash section empties detergent into dishwasher when you close the door The larger Main wash section automatically empties detergent into the dishwasher during the wash See the cycle Selection Charts Use automatic dishwashing detergent only Other detergents can produce excessive suds that can overflow out of the dishwasher and reduce washing performance j Govorinich 2 Main Wash section Add detergent just before starting a cycle S Pro Wash sactan Store tightly closed detergent in a cool dry place Fresh automatic dishwasher detergent results in better cleaning NOTE Do not use detergent with a rinse cycle Filling the dispenser 1 If the dispenser over is closed open the cover by pushing the cover latch 2 Fill the Main Wash section with detergent See How much detergent to use 3 Fill the Pre Wash section if needed 4 Close the dispenser cover It is normal for the cover to open partially when dispensing Serial Number Version 00 00 Edition Nov 23 2005 Haier Built In Dishwasher Model ESD400 ESD401 ESD402
37. on the track stop to make sure it is locked into place 4 Repeat on the other side 9 2 Loading Bottom Rack The bottom rack is designed for plates pans casseroles and utensils Many items up to 12 2 in 31 cm tall fit in the bottom rack See recommended loading patterns shown NOTE The features on your dishwasher rack may vary from the drawings shown Do not load glasses cups or plastic items in the bottom rack Load small items in the bottom rack only if they are secured in place Load plates soup bowls etc between tines Overlap the edges of Plates for large loads Load soup cereal and serving bows in the rack in a variety of ways depending upon their size and shape Load bowls securely between the rows of tines Do not nest bowls because the spray will not reach all surfaces Utensil load Load cookie sheets cake pans and other large items at the sides and back Loading such items in front can keep the water spray from reaching the detergent dispenser Secure heavily soiled cookware face down in the rack Make sure pot handles and other items do not stop rotation of the spray arm s Utensil load The spray arm s must move freely Do not load items between the bottom rack and the side of the dishwasher tub because they might block the water inlet opening NOTE Spin the spray arms Be sure items in the basket do not stop the rotation of the spray arms You can fold down two rows of tines at
38. osure Use the dishwasher only for its intended function i di aka te in Hen Lise only detergents or rinse agents recommended ma E ANAE EN GATTE for use id J el sea er Ope sat them out of the mE Do not abuse sit on or stand on the door lid or dish reach of children racks of the dishwasher When loading items to be washed To reduce the risk of injury do not allow children to 1 Locate sharp items so that they are not likely to play nf J mg e aaar Ma cab dee maa a damage the door seal and Under certain conditions hydrogen gas may be Load sharp knives with the handles up to reduce produced in a hot water system that has not been ES Oia ress E EO i TE Ifthe hot water system has not been oa ee bey il dle ere used for such a period before using the dishwasher Paice nye ASE Eh erie B ufa ly aE tum on all hot water faucets and let the water flow tems n a eat ee ee ee fram each for several minutes This will release any recommendations accumulated hydrogen gas As the gas is flammable Do nat touch the heating element during or donot smoke or use an open flame during this time immediately after use Remove the door or lid tothe washing compartment when removing an ad dishwasher from service or discarding it SAVE THESE INSTRUCTIONS Page 4 48 Serial Number Version 00 00 Edition Nov 23 2005 Haier Built In Dishwasher Model ESD400 ESD401 ESD402 Before Using Your Dishwasher GROUNDING INSTRUCTIONS 4A WARNING For a
39. ovide Easy access to water electricity and drain Convenient loading Corner locations require a 2 5 1cm minimum clearance between the side of the dishwasher door and wall or cabinet Square opening for proper operation and appearance Cabinet front perpendicular to floor Level floor If floor at front of opening is not level with floor at rear of opening shims may be needed to level dishwasher NOTE Shims must be securely attached to floor to prevent their movement when dishwasher is being operated If dishwasher will be left unused for a period of time or in a location where it may be subject to freezing have it winterized by authorized service personnel Make sure pipes wires and drain hose are within the shaded area HELPFUL TIP If the floor in the dishwasher opening in uneven example tile flooring only part way into opening you will needed to take special care in measuring dimensions and in leveling dishwasher Page 7 48 Serial Number Version 00 00 Edition Nov 23 2005 Haier Built In Dishwasher Model ESD400 ESD401 ESD402 Electrical It is the customer s responsibility To contact a qualified electrician To assure that the electrical installation is adequate and in conformance will all national and local codes and ordinances You must have 120 volt 60Hz AC only 15 or 20 amp fused electrical supply COPPER WIRE ONLY We recommend a time delay fuse or circuit breaker
40. r supply cord method A WARNING Electrical Shock Hazard Plug into a grounded 3 prong outlet Do not remove ground prong Do not use an adapter Do not use an extension cord Failure to follow these instructions can result in death fire or electrical shock Check that power supply cord does not touch dishwasher motor or lower part of dishwasher tub Goto step 5 Water Connection HELPFUL TIP Compression fittings Slide nut l onto copper tubing J about 1 inch 2 5 em Slide ferrule K onto the tubing Do not position ferrule on the end ofthe tubing Put the tubing into the elbow L as far as it will go Slide the nut and ferrule forward and start the nut onto the elbow threads M Be careful when handling and position ing the copper tubing It bends and kinks easily Peat fe ce To prevent vibration duning operation route the water sup ply line so thatit does not touch the dishwasher base frame or motor Make sure the water line stays within the shaded area shown on page 7 when the dishwasher Is installed inthe cabinet With copper tubing J pushed into compression fitting as far as it will go use an adjustable wrench and tighten com pression fitting nut I to elbow L on water inlet valve Page 22 48 Serial Number Version 00 00 Edition Nov 23 2005 Haier Built In Dishwasher Model ESD400 ESD401 ESD402 6 Place Paper towel under elbow Turn on water supply and che
41. r to the sides of the cabinet follow steps 6 through 12 Page 18 48 Serial Number Version 00 00 Edition Nov 23 2005 Haier Built In Dishwasher Model ESD400 ESD401 ESD402 Check the door spring tension With another person holding he dishwasher to prevent it from tipping open and close the doora few times lf the door opens by itself adjust the door spring tension To adjust the door spring tension unhook the spring T from he rear leg of dishwasher With a S16 nut driver or hex sockelremove the screw U from the tensioner W The screw can be put into one of three holes 1 2 3 in front leg of dishwasher The dishwasher is shipped with the screw in the back hole lf the door opened by itself move the lensionertohole 2 or 3 and replace screw Re allach door spring to rear leg Tensioners on both sides of dishwasher should be secured at same holes 14 rasp the dishwasher door at the edges of the door i panel Tilt dishwasher backwards on wheels 2 Move dishwasher close to cabinet opening Do not push on front of panel or on console they may dent d 5 If dishwasher has a power supply cord insert power supply cord into hole cut into cabinet 1 6 Check that water line is on the left side of opening and drain hose is near the center of the hole in the cabinet lf using direct wire check that itis on the right side of opening 1 T Carefully move dshwasher completely into cabinet opening
42. r water i i ia supply line z i M flashlight N Teflon tape or pipe joint compound gt th O shallow pan P Shim stock if installed with built up floor P electric drill Q 1 2 3 4 and 1 1 2 hole saw bits R small tubing cutter S wire stripper T 1 1 2 2 screw type clamp if connecting to waste tee U copper tubing 3 8 recommended or flexible stainless steel braided fill line V clamp connector or conduit connector to fit a 7 8 2 2cm diameter hole Page 6 48 Serial Number Version 00 00 Edition Nov 23 2005 Haier Built In Dishwasher Model ESD400 ESD401 ESD402 5 2 Parts supplied A 2 drain hose clamps Sa an 1 large 1 small We E ay n Make sure all these parts are included See parts list for accessories available for your dishwasher B 2 No ST4 2 X 18 Philips head screws i C Drain hose Cabinet opening Do not run water drain lines or electrical wiring where they can interfere with or contact dishwasher motor or legs The location where the dishwasher will be installed must provide clearance between motor and flooring Do not install dishwasher over carpeted flooring Protect dishwasher and water lines leading to dishwasher against freezing Damage from freezing is not covered by the warranty A side panel kit is available from your dealer for installing your dishwasher at end of cabinet Check location where dishwasher will be installed The location must pr
43. the front of the bottom rack Fold down rack 1 Grasp the tip of the tine that is in the tine holder 2 Genily pull the tine out of the tine holder 3 Lay the row of tines down in the rack to make room for larger dishes bowls i EE pots pans or roasters 9 3 Loading Silverware Basket Load the silverware basket while it is in the bottom rack or take Serial Number Version 00 00 Edition Nov 23 2005 Haier Built In Dishwasher Model ESD400 ESD401 ESD402 the basket out for loading on a counter or table See recommended loading pattern shown NOTE Unload or remove the basket before unloading the racks to avoid spilling water droplets on the silverware Load items with covers down using the separators to prevent silverware nesting Place small items such as baby bottle caps jar lids corncob holders etc in the section s with hinged cover s Close the cover to hold small items in place IMPORTANT Always load sharp items knives skewers etc pointing down Do not load silver or silver plated silverware with stainless steel These metals can be damaged by contact with each other during washing Some foods such as salt vinegar milk products fruit juices etc can pit or corrode silverware Run a rinse cycle if you do not have a full load to wash immediately 10 DISHWASHER USE 10 1 Proper Use of Detergent Use only detergent specifically made for use in dishwashers Cascade Cascade C
44. to dry and some spotting can occur For best drying always use a liquid rinse and Some items such as plastics may need towel drying NOTE Heated Dry is an option with Anti bacteria Wash Pots and Pans Wash Normal and China cycles If you change this option the remaining time displayed by LED will add reduce 25 minutes Sanitize Rinse Select this option to raise the Water temperature in the final rinse approximately 160 F 71 The Sanitize Rinse Option adds heat and time to the cycle This high temperature rinse sanitizes your dishes and glassware in accordance With NSF ANSI standard 184 for Residential Dishwashers Certified residential dishwashers are not intended for licensed food establishments Child Lock On ESD310 311 312 models Use Child Lock to prevent un intended use of the dishwasher You can also use the Child Lock feature to prevent unintended cycle or option changes during a cycle When Child Lock is lit all buttons are disabled NOTE The dishwasher door can be opened while the controls are locked To turn on the Lock Press and hold heated dry button for 3 seconds Child Lock glows If you press any pad while your dishwasher control is locked the light flashes 3 times and selection is ignored To turn off the Lock Press and hold Heated Dry button for 3 seconds The light turns off Delay Start On ESD310 311 312 models Select this option to run your dishwasher at a later time or during off peak hours You can add items to the load
45. ure to follow these instructions can result in death fire or electrical shock Install where dishwasher is protected from the elements Protect against freezing to avoid possible rupture of fill valve Such ruptures are not covered by the warranty See Storing in the Dishwasher Care section for winter storage information E Install and level dishwasher on a floor that will hold the weight and in an area suitable for its size and use E Remove all shipping plugs from hoses and connectorsisuch as the cap on the drain outlet before installing See Installation Instructions for complete information 4 Net dimension Page 5 48 Serial Number Version 00 00 Edition Nov 23 2005 Haier Built In Dishwasher Model ESD400 ESD401 ESD402 25 63 5em 4 b 23 7 8 760 6cem 4 Fz 3 4 1 9 cm insulation may be compressed 33 7 8 86cm min with wheels removed l H ar53 em 4 5 Installation 5 1 Tools and materials needed A pliers B Phillips screwdriver C 5 8 0pen end wrench D measuring tape or ruler E 10 adjustable wrench that opens to 1 1 8 2 9cm F flat blade screwdriver G gloves H utility knife 2 twist on wire connectors which are the proper size to connect your household wiring to 16 gauge wiring in dishwasher J small level K safety glasses r a L 90 bow with 3 8 N P T external threads on one end The other end must fit you
46. water temperature and detergents can affect finish of anodized aluminum No Do not wash throwaway aluminum pans in the dishwasher These might shift during washing and transfer black marks to dishes and other items No Wash bottles and cans by hand Labels attached with glue can loosen and clog the spray arme or pump and reduce washing performance No Seasoning will be removed and iron will rust Yas Always check manufacturer s recommendations before washing Antique hand painted or over the glaze patterns may fade Gold leaf Can discolor or fade Yas Check manufacturer s recommendations before washing Some types of leaded crystal can etch with repeated washing Alo Goald colored flatware will discolor Yas Milk glass yellows with repeated dishwasher washing No Handles of same Knives are attached to the blade with adhesives which can loosen if washed inthe dishwasher Alo High water temperatures and detergent can discolor or pit the finish Alo Cannot withstand high water temperatures and detergents Material Dishwasher Safe Comments Plastics Yes Always check manufacturer s recommendations before washing Plastics vary in their capacity to withstand high temperatures and detergents Load plastics in top rack only Stainless Steel Yes Run a rinse cycle if not washing Immediately Prolonged contact with food containing salt vinegar milk products or fruit juice can damage finish
47. wer switch N Turn on the switch Gf installed turned on N Change the film switch Y Change the controller Page 43 48 Serial Number Version 00 00 Edition Nov 23 2005 Haier Built In Dishwasher Model ESD400 ESD401 ESD402 Phenomenon the dishwasher is running properly without water in tub Is the water shut up valve turned on N Turn on the valve The overfill floater is Y Frese up The water pressure is too The water pressure is 20 120PSI slow a A booster pump before filling shoule be added Is the water inlet valve ok Change water Inlet valve Page 44 48 Serial Number Version 00 00 Edition Nov 23 2005 Haier Built In Dishwasher Model ESD400 ESD401 ESD402 Heating trouble Phenomenon program controller stop turning Whether socket connector is connected well Connect it well Whether thermo limiter is OK Whether heater is OK PCB or circuit 1s broken Page 45 48 Serial Number Version 00 00 Edition Nov 23 2005 Haier Built In Dishwasher Model ESD400 ESD401 ESD402 Power supply trouble Phenomenon dishwasher cannot work check whether the power connector Connect it properly is in position check whether the circuit N the cable or the controller board between the two terminals hond Ba disrecten is open Page 46 48 Serial Number Haier Version 00 00 Built In Dishwasher 19
Download Pdf Manuals
Related Search