Operation and Service Manual
Contents
1. Figure 2 2 16089B Product Overview Table 2 2 Contents of 16089B Description Agilent Part Number Quantity O Kelvin Clip Leads 16089 600021 1 Q Operation and Service Manual 16089 90010 1 1 Agilent internal only part number 2 Operation and Service Manual is not shown in Figure 2 2 Preparation for Use 2 3 16089C2. Figure 2 3 16089C Product Overview Table 2 3 Contents of 16089C Description Agilent Part Number Quantity D Kelvin Clip Leads 16089 60003 1 O Operation and Service Manual 16089 90010 1 1 Agilent internal only part number 2 Operation and Service Manual is not shown in Figure 2 3 2 4 Preparation for Use 16089D Figure 2 4 16089D Product Overview Table 2 4 Contents of 16089D Description Agilent Part Number Quantity O Alligator Clip Leads 16089 60004 1 Q Operation and Service Manual 16089 90010 1 1 Agilent internal only part number 2 Operation and Service Manual is not shown in Figure 2 4 Preparation for Use 2 5 Ambient Environmental Considerations Operating and Storage The 160894 B C D must be operated within an ambient temperature range of 0 C to 55 C and relative humidity up to 95 at 40 C non condensing The 16089A B C D may be stored within a temperature range of 40 C to 70 and ata relative humidity of up to 95 at 40 C non condensing Connecting the Test Leads for Use UNKNOWN terminals Turn levers right of Instruments 0888 Insert sda BSS Four terminal pair BNC terminals of test leads A9602001 Figure 2 5 Connecti
3. Note If the furnished short bar of 16089A or 16089D is corroded worn or damaged i reverse the position or replace it with a new short bar To reverse the short bar Y remove the 2 screws that fixes the short bar and reverse the position Operation Step by step instructions on how to make a measurement with the 16089A B C D are 1 Set the Cable Length setting to 1 m 4192A 4263B 4268A 4278A 4284A 4285A 4288A and 4294A only 2 Connect the test leads of 16089A B C D to the measurement Instrument s UNKNOWN terminals 3 Perform OPEN and SHORT compensation as described in the measurement instrument s operation manual Figure 3 3 and Figure 3 4 show how to make short condition for the SHORT compensation 4192A 4263B 4268A 4278A 4284A 4285A 4288A and 4294A only 4 Connect the component to be tested into the test clips Note When 16089D is used connect the test clips to the DUT correctly as follows A a Connect all test clips to the DUT Y Connect the same color test clips to the same terminal of the DUT m Connect the Hpot and Lpot clips marked V closer to the DUT than Heur and Leur Clips Figure 3 5 also shows how to connect a DUT using the alligator clips of the 16089D 3 4 Operation Hpot Lpot V markers Red Alligator Alligator Clip DUT Clip Figure 3 5 Connecting the DUT to the 16089D Operation 3 5 Service Introduction This chapter
4. 33126 U S A tel 305 267 4245 fax 305 267 4286 Australia New Zealand Agilent Technologies Australia Pty Ltd 347 Burwood Highway Forest Hill Victoria 3131 tel 1 800 629 485 Australia
5. 4 16089D aaa a 2 5 Ambient Environmental Considerations a a a a 2 a a a 2 6 Operating and Storage 2 6 Connecting the Test Leads for Use o oo a a a a 2 6 Packaging the Test Leads 2 a a a a a 2 6 3 Operation Introduction a a a a a 3 1 16089A BBC 2 aaa a 3 1 16089D aaa a 3 2 OPEN and SHORT Compensation a a e 3 3 Operation oo a a 3 4 4 Service Introduction a a a a a 4 1 Replaceable Parts 2 aoa a a a a 4 1 16089A Replaceable Parts a a a 4 1 16089B Replaceable Parts a a a 4 1 16089C Replaceable Parts 2 a a ee 4 2 16089D Replaceable Parts a a a a a 4 3 Contents 1 Figures 2 1 16089A Product Overview 2 2 2 2 16089B Product Overview 2 a a a a a a 2 3 2 3 16089C Product Overview 2 a a a a 2 4 2 4 16089D Product Overview 2 5 2 5 Connecting the Test Leads ee 2 6 3 1 16089A B C Test Leads Features e 3 1 3 2 16089D Test Leads Features A 3 2 3 3 Making a Short Condition for the 16089B and 160890 3 3 3 4 Making a Short Condition for the 16089A and 16089D 2 3 3 3 5 Connecting the DUT to the 16089D a a a a a a 3 5 4 1 Kelvin Clip Connections 4 2 Tables 1 1 Furnished Accessories 2 6 we a a 2 1 Contents of 16089A 2 2 A 2 2 Contents of 16089B a a 2 3 Contents of 160890 2 a a 2 4 Contents of 16089D 2 A 4 1 16089A Replaceable Pa
6. Technologies from another country Agilent Technologies warrants that its software and firmware designed by Agilent Technologies for use with an instrument will execute its programming instruction when property installed on that instrument Agilent Technologies does not warrant that the operation of the instrument or software or firmware will be uninterrupted or error free Limitation of Warranty The foregoing warranty shall not apply to defects resulting from improper or inadequate maintenance by the Buyer Buyer supplied software or interfacing unauthorized modification or misuse operation outside of the environmental specifications for the product or improper site preparation or maintenance No other warranty is expressed or implied Agilent Technologies specifically disclaims the implied warranties of merchantability and fitness for a particular purpose Certification The Agilent Technologies certifies that this product met its published specifications at the time of shipment from the factory Agilent Technologies further certifies that its calibration measurements are traceable to the United States National Institute of Standards and Technology to the extent allowed by the Institute s calibration facility or to the calibration facilities of other International Standards Organization members Exclusive Remedies The remedies provided herein are the buyer s sole and exclusive remedies Agilent Technologies shall not be liable fo
7. on the non marked side On the other Kelvin clip the gray cable is screwed on the V marked side and the black cable is serewed on the non marked side 16089C Replaceable Parts Table 4 3 16089C Replaceable Parts Reference Agilent Part Designator Number Qty Description 16089 60003 1 Test Leads 16089 04008 1 Cover Top 0515 0914 2 Screw Flat Head M3x0 5 L6 1 16005 60013 1 Test Clip Assembly Red 16005 60015 1 Test Clip Assembly Black 2 0890 1809 2 em Tube Heat Shrinkable Red 0890 1808 2 cm Tube Heat Shrinkable Black 1 Corresponding to designator in Figure 4 1 2 The whole unit Agilent internal only part Connection from the cables to the Kelvin clip is shown in Figure 4 1 E So TO ot 2 L Test Lead A9605001 Figure 4 1 Kelvin Clip Connections 4 2 Service 16089D Replaceable Parts Table 4 4 16089D Replaceable Parts Agilent Part Number Qty Description 16089 60004 1 Test Leads 16089 04004 1 Cover Top 0515 0914 2 Screw Flat Head M3x0 5 L6 0340 1085 2 Insulator Alligator Clip Red 0340 1086 2 Insulator Alligator Clip Black 1400 1252 4 Alligator Clip 7121 2696 2 Wire Marker V 16089 01201 1 Short Bar 0515 1550 2 Screw 1 The whole unit Agilent internal only part Table 4 5 shows the correspondence between the Alligator Clips and the
8. Agilent 16089A B C Kelvin Clip Leads Agilent 16089D Alligator Clip Leads Operation and Service Manual o Agilent Technologies Agilent Part No 16089 90020 Printed in JAPAN November 2002 Fourth Edition Notice The information contained in this document is subject to change without notice This document contains proprietary information which is protected by copyright All rights are reserved No part of this document may be photocopied reproduced or translated to another language without the prior written consent of the Agilent Technologies Agilent Technologies Japan Ltd Component Test PGU Kobe 1 3 2 Murotani Nishi ku Kobe shi Hyogo 651 2241 Japan Warranty This Agilent Technologies instrument product is warranted against defects in material and workmanship for a period of one year from the date of shipment except that in the case of certain components listed in this manual the warranty shall be for the specified period During the warranty period Agilent Technologies will at its option either repair or replace products which prove to be defective For warranty service or repair this product must be returned to a service facility designed by Agilent Technologies The Buyer shall prepay shipping charges to Agilent Technologies and Agilent Technologies shall pay shipping charges to return the product to the Buyer However the Buyer shall pay all shipping charges duties and taxes for products returned to Agilent
9. Cables Table 4 5 Clip and Cable Correspondence Alligator Clip Cable Color Color Marker Red Orange V Red Red Black Gray y Black Black Service 4 3 REGIONAL SALES AND SUPPORT OFFICES For more information about Agilent Technologies test and measurement products applications services and for a current sales office listing visit our web site http www agilent com find tmdir You can also contact one of the following centers and ask for a test and measurement sales representative 11 29 99 United States fax 61 3 9272 0749 Agilent Technologies tel 0 800 738 378 New Zealand Test and Measurement Call Center fax 64 4 802 6881 P O Box 4026 Englewood CO 80155 4026 Asia Pacific tel 1 800 452 4844 Agilent Technologies 24 F Cityplaza One 1111 King s Road Canada Taikoo Shing Hong Kong Agilent Technologies Canada Inc tel 852 3197 7777 5150 Spectrum Way fax 852 2506 9284 Mississauga Ontario L4W 561 tel 1 877 894 4414 Europe Agilent Technologies Test amp Measurement European Marketing Organization P O Box 999 1180 AZ Amstelveen The Netherlands tel 31 20 547 9999 Japan Agilent Technologies Japan Ltd Call Center 9 1 Takakura Cho Hachioji Shi Tokyo 192 8510 Japan tel 81 426 56 7832 fax 81 426 56 7840 Latin America Agilent Technologies Latin American Region Headquarters 5200 Blue Lagoon Drive Suite 4950 Miami Florida
10. ction gives supplemental performance characteristics Supplemental performance characteristics are not specifications but are typical characteristics included as additional information for the operator Supplemental performance characteristics are not guaranteed Supplemental Performance Characteristics of 16089 A m Applicable DUT size Diameter of DUT s terminals 0 0 0 000 ccoo lt 15 mm Supplemental Performance Characteristics of 16089B m Applicable DUT size Diameter of DUT s terminals 0 0 0000 ect reren lt 7 9 mm Length of DUT s terminals 0 00 00 00 ccc enn etn nent e tenes gt 3 mm General Information 1 3 Supplemental Performance Characteristics of 16089C m Applicable DUT size Diameter of DUT s terminals 0 00 00 00 ccc nsere eerren eee lt Space between DUT s terminals 00000 0 00 ccc nnn n teen e ees gt Length of DUT s terminals o gt Supplemental Performance Characteristics of 16089D m Applicable DUT size Diameter of DUT s terminals o lt 1 4 General Information Preparation for Use Introduction This chapter explains how to install the Agilent 16089A B C Kelvin Clip Leads and Agilent 16089D Alligator Clip Leads The topics covered include initial inspection ambient environmental considerations connecting the test leads for use and repackaging the test leads for shipment Initial Inspection These test leads have been carefully
11. dition or the like which if not correctly performed or adhered to could result in injury or death to personnel Caution sign denotes a hazard It calls attention to a procedure practice condition or the like which if not correctly performed or adhered to could result damage to or destruction of part or all of the product Note denotes important information It calls attention to a procedure practice condition or the like which is essential to highlight Contents 1 General Information Introduction a a a a a l 1 Using the 16089A BC D aaa a a ee en 1 1 Product Description ccccccllc a 1 1 Accessories Supplied 2 1 1 A 1 2 Operating and Safety Precautions 2 1 2 Operating Ce e 12 Service ccccclccl ee Ce 1 2 Specifications Ce A 1 3 Common Specifications for the 16089A B C D o 1 3 Specifications for the 16089A B C Cc 1 3 Specifications for the 16089D Ce 1 3 Supplemental Performance Characteristics Ce o 1 3 Supplemental Performance Characteristics of 16089A 1 3 Supplemental Performance Characteristics of 16089B 2 2 1 3 Supplemental Performance Characteristics of 160890 1 4 Supplemental Performance Characteristics of 16089D 1 4 2 Preparation for Use Introduction a a a a a 2 1 Initial Inspection 2 a a a a a 2 1 16089A aaa a 2 2 16089B aaa a 2 3 160890 aaa a 2
12. gives replaceable parts information for the 16089A 16089B 16089C and 16089D Replaceable Parts Table 4 1 Table 4 2 Table 4 3 and Table 4 4 list the replaceable parts for the 16089A B C and D respectively Figure 4 1 shows the connection from the cable to the clip assembly of the 16089C The parts listed can be ordered from your nearest Agilent Technologies office Ordering information should include the Agilent part number and the quantity required 16089A Replaceable Parts Table 4 1 16089A Replaceable Parts Agilent Part Number Qty Description 16089 60001 1 Test Leads 16089 04001 1 Cover Top 0515 0914 2 Screw Flat Head M3x0 5 L6 16089 60011 2 Large Clip Assembly 7121 2696 2 Wire Marker V 16089 01201 1 Short Bar 0515 1550 2 Screw 1 The whole unit Agilent internal only part Red and orange cables are screwed on the one Kelvin clip assembly Gray and black cables are screwed on the other Kelvin clip assembly Orange and gray cables are marked V 16089B Replaceable Parts Table 4 2 16089B Replaceable Parts Agilent Part Number Qty Description 16089 60002 1 Test Leads 16089 04002 1 Cover Top 0515 0914 2 Screw Flat Head M3x0 5 L6 16005 60010 2 Kelvin Clip Assembly 1 The whole unit Agilent internal only part Service 4 1 On one Kelvin clip the orange cable is serewed on the V marked side and the red cable is screwed
13. inspected electrically and mechanically before being shipped from the factory They should be in perfect physical condition no scratches dents or the like and they should be in perfect electrical condition Verify this by carefully performing an incoming inspection to check the test lead set for signs of physical damage and missing contents If any discrepancy is found notify the carrier and Agilent Technologies Your Agilent Technologies sales office will arrange for repair and replacement without waiting for the claim to be settled 1 Inspect the shipping container for damage and keep the shipping materials until the inspection is completed 2 Verify that the shipping container contains everything shown in Figure 2 1 Figure 2 2 Figure 2 3 and Figure 2 4 and listed in Table 2 1 Table 2 2 Table 2 3 and Table 2 4 3 Inspect the exterior of the 16089A B C D for any signs of damage Preparation for Use 2 1 16089A Figure 2 1 16089A Product Overview Table 2 1 Contents of 16089A Description Agilent Part Number Quantity D Kelvin Clip Leads 16089 60001 1 O Operation and Service Manual 16089 90010 1 1 Agilent internal only part number 2 Operation and Service Manual is not shown in Figure 2 1 2 2 Preparation for Use 16089B
14. ipped with two insulated Kelvin clips Three sizes of Kelvin clips are provided The 16089A Kelvin Clip Leads is equipped with two large Kelvin clips the 16089B Kelvin Clip Leads is equipped with middle size clips and the 16089C Kelvin Clip Leads is equipped with small size clips The 16089D consist of a direct attachment four terminal pair type test leads that are equipped with four alligator clips General Information 1 1 Accessories Supplied The following accessories are supplied with the 16089A B D Table 1 1 Furnished Accessories Description Part Number Quantity Operation and Service Manual P N 16089 90010 1 Operating and Safety Precautions Operating You need observe only normal precautions in handling and operating the 16089A B C D Do not exceed the operating input power voltage and current level and signal type appropriate for the instrument being used refer to your instrument s operation manual Caution Electrostatic discharge Esp can damage the highly sensitive microcircuits in your instrument ESD damage is most likely to occur as the test leads are Y being connected or disconnected Protect them from ESD damage by wearing a grounding strap that provides a high resistance path to ground Alternatively ground yourself to discharge any static charge built up by touching the outer shell of any grounded instrument chassis before touching the test port connectors Never touch the test cli
15. ltages capable of causing death are present in this instrument Use extreme caution when handling testing and adjusting this instrument Safety Symbols General definitions of safety symbols used on equipment or in manuals Warning Y Caution Y Note vi Instruction manual symbol the product will be marked with this symbol when it is necessary for the user to refer to the instruction manual in order to protect against damage to the instrument Indicates dangerous voltage terminals fed from the interior by voltage exceeding 1000 volts must be so marked Protective ground terminal For protection against electrical shock in case of a fault in the instrument Used with wiring terminals to indicate the terminal which must be connected to ground before operating equipment Low noise or noiseless clean ground earth terminal Used for a signal common as well as providing protection against electrical shock in case of a fault in the instrument A terminal marked with this symbol must be connected to ground in the manner described in the installation Operation manual and before operating the equipment Frame or chassis terminal A connection to the frame chassis of the equipment which normally includes all exposed metal structures Alternating current power line Direct current power line Alternating or direct current power line Warning denotes a hazard It calls attention to a procedure practice con
16. ng the Test Leads Packaging the Test Leads If shipment to a Agilent Technologies service center is required each test lead set should be repackaged using the original factory packaging materials Alteratively comparable packaging materials may be used Wrap the test leads in heavy paper and pack in anti static plastic packing material Use sufficient shock absorbing material on all sides of the 16089A B C D to provide a thick firm cushion and to prevent movement Seal the shipping container securely and mark it FRAGILE 2 6 Preparation for Use Operation Introduction This chapter describes using the test leads and compensation techniques for these test leads 16089A B C 16089C 16089A 16089B 49603001 Figure 3 1 16089A B C Test Leads Features 1 Kelvin Clips These are connected to the DUT 2 Four terminal pair BNC terminals These terminals are connected to the UNKNOWN terminals of your measurement instrument Operation 3 1 16089D 16089D ALLIGATOR CLIP LEADS A9603002 Figure 3 2 16089D Test Leads Features Alligator Clips red These are connected t
17. nologies assumes no liability for the customer s failure to comply with these requirements Do NOT operate in an Explosive Atmosphere Do not operate the instrument in the presence of flammable gasses or fumes Operation of any electrical instrument in such an environment constitutes a safety hazard Keep Away from Live Circuits Operating personnel must not remove instrument covers Component replacement and internal adjustments must be made only by qualified maintenance personnel Do not replace components with the power cable connected Under certain conditions dangerous voltages may exist even with the power cable removed To avoid injury always disconnect power and discharge circuits before touching them Do NOT Service or Adjust While Alone Do not attempt internal service or adjustment unless another person capable of turning off power and capable of rendering first aid and resuscitation is present Do NOT Substitute Parts or Modify Instrument Because of the danger of introducing additional hazards do not substitute parts or perform unauthorized modifications to the instrument Return the instrument to a Agilent Technologies Sales and Service Office for service and repair to ensure the safety features are maintained Dangerous Procedure Warnings Warnings such as the example below precede POTENTIALLY DANGEROUS PROCEDURES throughout this manual Instructions contained in the warnings must be followed Warning Dangerous vo
18. o the high terminal of the DUT Alligator Clips black These are connected to the low terminal of the DUT V markers These show the Hpot and Lpot terminals Ae N e Four terminal pair BNC terminals These terminals are connected to the UNKNOWN terminals of your instrument 3 2 Operation OPEN and SHORT Compensation The 160894 B C D have inherent stray capacitance residual inductance and residual resistance that affect the measurement To cancel the effects caused by these residuals and thus minimize their effect on measurement accuracy the measurement instrument s OPEN and SHORT compensation capabilities must be used The procedures are described in the measurement instrument s operation manual Y marks Black Voltage terminal Voltage terminal Current Current terminal terminal Current terminal 16089B 16089C Figure 3 3 Making a Short Condition for the 16089B and 16089C When you perform SHORT compensation for the 16089A or 16089D use the furnished short bar as shown in Figure 3 4 V markers Short Bar Lt Sava AMO WOLNO sor 16089A 16089D 49603003 Figure 3 4 Making a Short Condition for the 16089A and 16089D Operation 3 3
19. p contacts Use a work station equipped with an anti static work surface Service The voltage levels found in these test leads when used with the intended instruments do not warrant more than normal safety precautions for operator safety Nevertheless service should be performed only by qualified personnel 1 2 General Information Specifications This section lists the complete 16089A B C D specifications These specifications are the performance standards and limits against which the 16089A B C Dis tested When shipped from the factory the 16089A B C D meets the following specifications Common Specifications for the 16089A B C D Applicable Instrument PO 4263B 4268A o 4278A 4284A 4285A 4288A 4192A 4194A 4294A Maximum de Bias Voltage 00 rr 42 V peak max Frequency Range c 0oooocococccco een een tenn tte ene es 5 Hz to 100 kHz Operating Temperature 0 0 00 enura EEEE EEEE EEEE EEEE 0 to 55 C Operating Humidity o ae ee teen etnies lt 95 RH 40 C Non operating Temperature cciciiiiiis ie 40 to 70 C Non operating Humidity 0 0 0 0 002 n tenes lt 95 RH 40 C Weight 2 2 ee enn een dete need dnt teen tte e ttt n net eenes 300 g 1 Except for the frequency range over 100 kHz Specifications for the 16089A B C Cable Length ooo 0 94 m Specifications for the 16089D Cable Length ooo 1 3m Supplemental Performance Characteristics This se
20. r any direct indirect special incidental or consequential damages whether based on contract tort or any other legal theory Assistance Product maintenance agreements and other customer assistance agreements are available for Agilent Technologies products If you need assistance contact your nearest Agilent Technologies Sales and Service Office Addresses are provided at the back of this manual Copyright 1991 2000 2001 2002 Agilent Technologies Japan Ltd Manual Printing History The manual printing date and part number indicate its current edition The printing date changes when a new edition is printed Minor corrections and updates which are incorporated at reprint do not cause the date to change The manual part number changes when extensive technical changes are incorporated November 1991 2 2 0 0 0 ccc nes First Edition part number January 2000 aaan ccc cence es Second Edition part number April 2001 Third Edition part number November 2002 2 00 0 0c ccc cece cece eens Fourth Edition part number 16089 90000 16089 90000 16089 90010 16089 90020 Safety Summary The following general safety precautions must be observed during all phases of operation service and repair of this instrument Failure to comply with these precautions or with specific WARNINGS given elsewhere in this manual violates safety standards of design manufacture and intended use of the instrument The Agilent Tech
21. rts a a 4 2 16089B Replaceable Parts a a 4 3 16089C Replaceable Parts a a a a 4 4 16089D Replaceable Parts a a a a a 4 5 Clip and Cable Correspondence oo a a a a a a Pree RN NNN 00 NA OP wD DY Contents 2 General Information Introduction The purpose of this manual is to enable you to use your Agilent 16089A B C Kelvin Clip Leads and Agilent 16089D Alligator Clip Leads efficiently and confidently This manual contains both general and specific information To use the 16089A B C D to perform a specific function without having to read the entire manual follow the directions in Using the 16089A B C D Using the 16089A B C D The 16089A B D has been designed to operate specifically with the 4263B LCR Meter a To install the 16089A B C D turn to Chapter 2 m To operate the 16089A B C D turn to Chapter 3 a To order replaceable parts for the 16089A B C D turn to Replaceable Parts in Chapter 4 Product Description The 16089A B D has been designed to operate specifically with the following four terminal pair type LCR meters and impedance analyzers 4263B 4284A 4192A 4268A 4285A 4194A 4278A 4288A 4294A The 16089A B C D make it possible to measure odd shaped components that cannot be measured with conventional test fixtures The 16089A 16089B and 16089C consist of a direct attachment four terminal pair type test leads that are equ
Download Pdf Manuals
Related Search